Hi all,
I have a problem with MS Voice Command 1.6.
It 'sorta' works right now ... when I press the button on my BT headset (Motorola H700) it initiates the voice command on the Treo. However, the 'beep' is played from the treo speaker, not the BT headset. When I spoke the voice command, I must also speak to the Treo mic, not the BT headset. This sucks when you are in a noisy environment.
When the call is connected, it does go through the BT headset so that's good. But it's just when you want to initiate a voice command, you have to speak to the mic on the phone. All the announcements also come through the phone's speaker only, not the BT headset.
Has anybody found a fix to this?
Thanks in advance
Try deleting the headset and reacquiring it via bluetooth. I had to do this a couple of times before this corrected
Hmmm I've done it quite a few times already ... but I can try it again.
Mine does this too. If there is no fix, I will have to go back to the at&t one.
Removing and re-adding BT headset doesn't work. After doing some more homework, it seems like the problem is Treo 750, among a # of other phones (like Hermes) uses a BT stack that is incompatible with MS's and that is the reason why.
Searching on the Hermes site there IS actually a workaround which fixes half the problem.
To make long story short, after trying to fix recommended by that site, now I can speak to the BT headset to issue voice command.
Meaning, when I press the BT headset button, I hear the VC chime from my headset, not from the phone's speaker. And when I issue voice command I also speak to the BT headset, not the phone's mic.
What it doesn't fix, is notification STILL comes through the phone's speaker and not the BT headset, even with all the correct settings under MVC.
But I'm ok with that ... I can live with this.
number16 said:
Removing and re-adding BT headset doesn't work. After doing some more homework, it seems like the problem is Treo 750, among a # of other phones (like Hermes) uses a BT stack that is incompatible with MS's and that is the reason why.
Searching on the Hermes site there IS actually a workaround which fixes half the problem.
To make long story short, after trying to fix recommended by that site, now I can speak to the BT headset to issue voice command.
Meaning, when I press the BT headset button, I hear the VC chime from my headset, not from the phone's speaker. And when I issue voice command I also speak to the BT headset, not the phone's mic.
What it doesn't fix, is notification STILL comes through the phone's speaker and not the BT headset, even with all the correct settings under MVC.
But I'm ok with that ... I can live with this.
Click to expand...
Click to collapse
you have a link to this fix???
Related
I have bluetooth headset NOKIA BH-101. it works with my htc tornado like handsfree. but i can not get it play all sounds. it only works with calls but when ii play sounds or video files it sounds out of my phone.
This gadget supports Hands-Free and Headset but does not work with voice dial function. Can anybody help?
makler1981 said:
I have bluetooth headset NOKIA BH-101. it works with my htc tornado like handsfree. but i can not get it play all sounds. it only works with calls but when ii play sounds or video files it sounds out of my phone.
This gadget supports Hands-Free and Headset but does not work with voice dial function. Can anybody help?
Click to expand...
Click to collapse
try to chek the settings
bestever said:
try to chek the settings
Click to expand...
Click to collapse
what exact setting do you mean?
try this cab i found on http://mobile.surrealnetworks.com/
Check this thread too:
http://forum.xda-developers.com/showthread.php?t=263735&highlight=a2dp
This will install newest bt stack.
I should also ask which ROM you're using. The newer ROMs seem to be a lot better.
I'd also like anyone who could to tell me which BT stack is included on the newer ROMs, like Nitro or vjgrace.
Exitao said:
Check this thread too:
http://forum.xda-developers.com/showthread.php?t=263735&highlight=a2dp
This will install newest bt stack.
I should also ask which ROM you're using. The newer ROMs seem to be a lot better.
I'd also like anyone who could to tell me which BT stack is included on the newer ROMs, like Nitro or vjgrace.
Click to expand...
Click to collapse
my ROM is WM6 by vjgrace v3.4
Again I could describe my Nokia BH-101 BT headset with handsfree functionality on WM6 by vjgrace v3.5. It works nice as headset i can hera incoming calls, answer them, call last dialed number. But I CAN NOT make it start voice calling, due to device itself - it does sounds special tone that means that voice dial is started, but my phone does not recognise it. by the way useing celetask - there is special feature - that alows you to redirect all sound to headset and it work. As for me i don't need it (you are to have special BT Headset for listening to music. This headset generates rather bad sound(but not voice).
So again
I can do:
makle calls,
answer calls,
dial last dialed call.
swap and hold calls.
I can not do:
make voice dial
any voice commands
What are the problems:
Everytime I answer the call not by the headset but via the phone it looses the connection with headset, so i need to restart BT service (or headset).
It happens even if I answer by headset but during the call i need to speak via phone then i press right softkey and choose "turn handsfree off" and aain phone looses the headset
In this case I I make new call but in right soft key menu "turn handsfree on" is not active
If it's possible to make phone speak contact's name litterally during incoming call so i could know who is calling me.
IRC, voice dialling with WM phones is a bit of a problem. I seem to recall reading about this somewhere in the XDA-Dev forums.
On my headset, the function that calls for redial is the same for voice dial (wtf? I know.) It always redials.
As for the speaking of the contacts' names, it should be possible... if your phone can speak the contacts' recorded voice names w/o BT.
I'm sure you've heard of this issue before but I was unable to find a fix!
I have been using VC1.6 through strictly the device mic / speaker and it has worked great except for some reason it does not announce incoming calls.
Currently using ATT TILT with WM6
Using 520 Plantronics BT Headset
I downloaded "Bluetooth Voice Command Configuration" from XCSdM but it doesn't seem to do anything to help!
When I press the talk/end button on the Headset it enables the bluetooth static but it does not give the VC prompt.
I'd also like it to be able to announce incoming calls through the bluetooth!
Anyone?!
Well, I got the incoming calls to announce!!! Now all I need to do is find out how to get the VC1.6 and my bluetooth synced so that when I press my bluetooth headset button it activates the VC...
Please? LOL
Does your bluetooth headset support the handsfree profile? Not all headsets support the handsfree profile (even if you can use it to pick up and answer calls). I've got VC 1.6 and voice command working just fine with my Tilt and Jabra 8010.
edit: seems your plantronics does support the HFP. Did you ensure you "checked" the box for Hands Free Service when you paired it?
Yes, it's completely paired and the handsfree is checked :-\
I'm stumped. I get incoming call notifications, I get announcement reminders, etc.... but when I push the button on the headset it tries to initiate (or answer) a call.... If I hold it down, it powers off the headset. If I double click it, it calls the last person I talked to.
Maybe I just don't know how to function my headset to get it to prompt for VC?
I followed the "RandyRants" Tip to get everything working and it did activate the announcement of incoming calls, etc... just can't make commands yet.
I'm also using the BT VC Config enabled @ 30 duration.
I'm 1/2 way there!! Now I just need to cross the finish line...
Here's the link yo RandyRants that I followed: http://www.randyrants.com/2007/05/wm6_tip_voice_c.html
Any advice?
Hi guys,
Have just installed skype but for some reason it outputs to the device loud speaker rather than the earpiece speaker. Any idea how to change this?
Cheers
I discovered the same thing - using the earplugs that come with the phone will isolate it though, and I assume a bluetooth handsfree set as well.
Bluetooth headset doesn't work for me in Skype, only the wired headset that ships with the device (which is fine).
I have used Skype on the Orbit2. It appeared the same problem and i think there is no solution at the moment. Maybe you can test it with the fring client.
I using Fring for my VOIP and output is on loud speaker as well
Does Fring work for you? The latest version always deletes my WiFi settings (does the same on my Prophet), and I have the hideous malarky of re-entering the WEP key.
yeah this is an old problem, it existed back in the day of the TyTn. It appears it's still unclear if this is a WM or Skype problem. You can use a bluetooth device if you reroute the audio using a third party application:
http://pocketpccentral.net/help/a2dp.htm
http://www.davidmays.com/blog/?postid=6
http://handheld.softpedia.com/get/Audio/BlueTooth-Audio-Today-42630.shtml
Skype forum dealing with this issue:
http://forum.skype.com/index.php?showtopic=96266&st=20
Hello,
a friend of mine have some troubles with his TP and a Blaupunkt Radio with build in handsfree.
The Bluetooth pairing was completed without any problems.
When a calls comes the radio mutes and switch to handsfree - thats ok
The caller can hear your voice over the handsfree microphone, but you can't hear the caller. It is the TP build in speaker used, not the handsfree speaker.
The TP has the headset symbol shown in the upper right corner of the dialer.
Second the radio don't switch back to radio when the call ist ended the Bluetooth Connection stays up. Only deactivating/activating of Bluetooth at TP closes the connection and the radio switch back.
I hope somebody can help me...
Thanks!
I had this problem with my TYTN using shaps rom. you ave to turn on the hands free on the first incoming call and then further calls are OK. (right menu and turn on hands free)
this has to be done every time you get in the car though.
Its a pain i never found a fix. I havnt used this on my Touch Pro yet.
With Pioneer DEH55BT all working fine.
Thanks for the workaround... Perhaps it works for my friend, i will test it in the afternoon.
But another radio is no solution,it have to be this!
Try installing jetware mobile, it improves the bt connection but I don't know if it will solve your problem.
Hey guys
I recently bought a Chatterbox XBi2 bluetooth headset that supports A2DP and Handsfree, and using MSVC the mic is activated on the phone, not the headset.
I am able to play music through it, and I can answer calls in the default configuration.
The default behaviour for the main button is to run redial.exe, and none of the remap posts I tried (reg keys/dll's/etc) worked, so I just copied voicecommand.exe over redial.exe, and this does work as it should. (MSVC voice launches and comes over the headset).
The problem is, the mic that is activated is the mic on the phone, not on the headset.
This is driving me nuts, as this headset is completely useless to me without MSVC.
Can anyone help???
thanks
Cory
EDIT: I have a touch diamond
I've been searching my ass off to no avail, someone must know something to point me in the right direction.
thanks