Hi,
Recently my jasjam call, end, i.e,msg, start,ok and soft buttons light up but dont respond but at the same time the center control and side buttons do work (always). its not a physical problam coz i can still perform soft/ hard resets. i checked buttons option but all good. this problem comes and goes.
its strange.
Please help
pete
Related
I am getting a red green and blue screen with the 8125 when It turns off and then on :? and I have to hard reset but when I hard reset I don't loose my data. but my camera button doesn't work and my camera randomly opens after my 8125 comes out of sleep. Any Ideas on How to fix it???
By any chance is 8125 another name for Prophet\jamin\qtek s200?
What you are describing sounds like the bootloader, which you enter by pressing power + camera + reset.
I think your camera button is stuck and sending key presses at random.
Also, I think your comm manager button (under the volume slider) isn't working so instead of hard reset you get a soft reset which is the only way to exit bootloader.
8125
I think it is a wizard. But you can confirm at Cingular.com
Comm button works for sure but camera button doesn't seem to work even though it presses in. Thought it was software not hardware making it not work.
If you're using the stock case that came with the phone, that might be causing issues as well. check out this thread: http://www.howardforums.com/showthread.php?t=909904
Checked out cingular site. Scratch what I said about comm button, the HR on your device is probably different then mine, but I still think you are entering bootloader when you turn on your device.
Since it doesn't happen each restart, I doubt it's software related, especially since you are having trouble with the camera button. The only connection between camera and bootloader I can think of is the hardware button combination used.
Hi all
my device has become stuck and wont accept any screen inputs, but it will let me access some functions via the standard buttons. I think I need to perform a hard reset.
I have tried doing this by ressing power and soft reset but it doesn't seem to work.
As I dont have my booklet here I dont know if there's something else I should be doing.....
any advice at all please?
Thx
Press and hold both soft-key buttons, stick the stylus in the reset hole, release reset and wait for bootup to begin before releasing the soft-key buttons.
As I recall you get a confirmation screen.
Soft keys being the 2 hard keys above the ok and windows keys.
some random reason mine dosen't work
it will work.... use any solid PIN / Needle while prss n hold soft keys... mine worked
I'm using "Dutty's TouchFlo Rom 2 Final" on my tilt, but am facing problem with call end key. It doesn't respond during call and even in sleep mode...
I installed Tilt keyboard fix but no success..
Any help would be appreciated..
Regards..
I tried original ATT ROM... I think its hardware problem... coz when I press repeatedly it works... Can anyone help me out or tell me any solution..
Function design issue!
It is a design issue. To end a call you must either press the End Call (Hang-Up) button twice or press and hold on it. From a design stand point, this would prevent inadvertent hanging up on your caller while holding onto the phone and just clicking the hang-up button by mistake. At least that is what I was told by HTC.
Thank you so much asfoor. But sometimes i just end call with a single click and some time I have to press hard to end the call, same is when it goes to sleep mode...
I don't have that issue on the TyTN II. If it happens with different ROMs, then it's a hardware issue -- probably something in the contacts area.
it means i have to open it
When I wake the polaris up, it seems that the left button (the one in the wheel) is permanently pressed until I press another button. I have to do this in order to unlock the device, as the button is pressed I only get the message "Press cancel and then unlock".
This happens every time I wake up the device and sometimes when I am using it in other situations. It is almost unusable in this state.
I suppose it is a hardware problem. Any ideas for a way to fix it? I wouldn't like to send it to service, but I am fearing this is the only chance I have now. Any help would be appreciated. I have already switched it off, and also removed the battery for a while, but I have the same problem when I turn it on again.
This has happened to me for the first time yesterday. The device has not fallen to the ground any time since I have it (since February). I only carry it in my pocket.
Thanks for your help.
ah, I forgot to tell you. When the button stops being pressed (because I have pulsed another one) it doesn't work anymore. If a press it, no effect, the cursor doesn't move to the left...
I have read in another forum that someone who had a similar problem with the wheel managed to solve it by doing a hard reset and by restoring a backup done before the problem. He stated that using the option "erasing memory" didn't work and that he had to do the hard reset by doing "gps button + ie button + soft reset".
Here is the funny thing. I cannot do that kind of hardreset. Why? Because as the left button seems always pressed the confirmation screen in which you must press the send button to perform the hard reset, never appears. I guess it is due to the cruise which detects that the combination of buttons is no good or because the confirmation screen is shown but as the left button is pressed, you do not have enough time to press the send button (I don't even see the screen).
Is there anyway to perform the hard reset in another way? Thanks for your help...
Well, my cruise works fine now. What have I done? Nothing. Maybe it was a hardware problem in the contact of the button (some dirt or whatever) and now it is working. I don't know, although it wouldn't surprise me if it were software (I had a similar problem with the vibrator in a Mio A701, two days broken, got to work after that and never again failed). I just used the bluetooth and received a couple of calls.
Now I can hardreset. As the button is no longer permanently pressed, the combination of buttons works. Although I haven't pressed "send" to actually do it, since it seems fine.
More here if it fails again, but as I told you I read similar problems in the wheel in another forum...
hi. my soft keys on desire s starts to behave very strange. i thought that it was only problem in one rom, but now it appears in every rom which i flashed. so basically when i hold phone without touching anything except side and back body it is sometimes like i pushed home or search soft key. also back soft key button is big problem, when i push it it works as back,home and search button. any idea what might be problem? or should i just send phone to repair?