Related
Can someone upload an old ROM for the prophet? I can't start up my prophet, but I've got it in bootloader. So I nedd a little bit old ROM so I can install on it.
Understand?
Thanks!
Look for the first link here http://forum.xda-developers.com/showpost.php?p=1166927&postcount=2
Are this ROM old ROM?
Not really old but if your phone stuck in bootloader this one is ok
I can't make it, it says that i should connect to Active Sync, and how im I suppose to do that?
Go in bootloader (screen with 3 coulours) by Hold down the camera button and reset the device. (Boot Loader Mode is: Press Camara + Soft Reset, then release soft reset and keep pressing camara button till appear the Boot Loader.)
When you are in bootloader logicaly your PC must detect the Prophet, then run the update
Sorry for my bad English but I'm Franch
Yes i've got it in bootloader, and its stands USB on the PPC screen. But it aint the Active Sync that finds it, it says "Uknoknown Unit" or something when i connect them together..
Active Sync isn't a problem, update work or there is an error message?
In right corner down on the PC sreen it comes up "A unkknown Device connected" or something like that, nothing more is happening..??
It sayd that it can't recognize the unit..
Qtek_S200 said:
It sayd that it can't recognize the unit..
Click to expand...
Click to collapse
In bootloader mode, on connecting via usb ,if u r getting 'USB' written on left down corner of ppc then ur ppc can be flashed via proper RUU and nk.nbf
Be sure that this nk.nbf dont include ipl/spl parts for risk free flashing and for not getting brick device.
thanx
nandlal
Im trying to flash a ROM with that, but it coming up on the screen that "Not connected". It's standing that i nedd to connect with Active SYnc!!
could somebody upload an ipl/spl lower than 2.09 or higher but not 2.09^^
rest doesn't matter language english or german would be good...
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
I think you have been bricked your device...
dineshkumaar said:
Hi...
I was trying to Upgrade my O2 XDA Exec Rom with Windows Mobile 6.5 by explode. The process went successfully till 99% and after that it ended up with Error. Then I unplugged my pda from the pc and tried to restart the device. I was surprised that the device did not respond to any of the following
Soft Reset
Hard Rest
Boot Loader mode Start (Bulb + Power + Reset)
It is totally blank screen whatever you do.
When I connected the device to the pc with usb cable, a Red Light is shown for 2 seconds and then goes off and a message comes up on the pc that "USB DEVICE NOT RECOGNIZED".
Then I tried to Remove battery from the device for a whole night and the next day morning i did all the above procedures again to get no results.
Kindly Help me out
Thanks
Dinesh Kumaar
Click to expand...
Click to collapse
if it's not recognized, remove the SIM card, the SD card, and on the PC open activesync and disable usb connections. for more info open this link
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
what if the device is bricked
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
dineshkumaar said:
Thanks for your quick reply
Kindly let me know what could be done with the bricked device. Can it be repaired again.
Thanks again
Dinesh Kumaar
Click to expand...
Click to collapse
you have to find another rom and try to flash it to your PDA.
ARE YOU RUNNING windows XP on your PC?
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
dineshkumaar said:
Yes ! I have Windows XP SP2 and Active Sync Version 4.5.0 (Build 5096)
Thanks
Click to expand...
Click to collapse
have you tried to upgrade another ROM, and if you did, is your PDA now working?
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
dineshkumaar said:
I cannot update my rom as my pc cannot recognize my device. is there any other way to update rom?
Click to expand...
Click to collapse
Have you read here?
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader_Serial
Try to reflash with another ROM
Hope it helped
And don´t forget to vote!
I had already done those steps to get no results.
its my badluck.
If you cannot get into bootloader and you have done the steps above, then you cannot flash to another rom.......it would seem you now have a paperweight im afraid
I am still not able to revive my device. I know that it is just due to corrupt bootloader but don't know how to repair it.
If anybody ever has solution for this... kindly let me know.
Regards
Have you tested mtty?
I would recommend to PM a chef on Universal forum
Good luck,
Mtty is not detecting my device
it says can't open usb port
One More thing I have noted is that when I keep the device connected with the pc, at a certain interval of about 10-15 mintues my device's Led shows RED Light for few seconds and then turns off followed by the the "USB device not recognized" on my pc.
I hope this can be used as a hint towards reviving my device.
Regards
have you followed orbs advise above and pm a chef on that section, they maybe able to help. From my knowledge (limited on that device) i ddont think there is any recovery proceedure that you have not tried. Have u downloaded offical wm5 rom and tried it. I know and appreciate that it will probably not work due to corrupt bootloader, but what else is there to do??
To understand more, what did you do PRIOR to trying to flash to 6.5.
Did you hardspl correctly? Had you already flashed to another rom and just felt like flashing to another new rom?? Give us more detail.
Thanks for your reply
I dont know how to PM Chef.
I had used 3 other Rom versions of WM6.1 on my device. They ran very much fine on my device. But When i found WM6.5 xplode, I wished to try that too. But the rom update procedure went successfully till 99% and after that it showed an error that upgrade was not successfull. I pulled out the device and tried to restart if by all methods but I wasnt able to power on at all.
Thanks
Regards
ok, goto the thread that you got the rom off, click the chefs name and you will get a menu there to send pm, do it, he might have seen a similar problem or know how to correct bootloader.
good luck
noup really no...
Is bricked
my bro has bricked an Universal and the same led turns red no power off no bootloar no power it means the flash chip is dead!
Sorry to heard that.
He waits too long for the upgrade it tooks at least 40 minutes
then ERROR... but you know... the batt was died in middle process ( th batt was ****ed up, it say full charged but no! it was on 60 or 50%) then the stupid thing is make a hardreset.. i told him dont hR your device... justa simple reste and reinit the process... and huh! its bricked.
if you are interested on sell your parts
maybe my bro want some parts.
my advice(similar to other people):
1. Charge your batery somehow (in other device or anything else)
2. put your devce in bootloader mode and connect it to pc - it wll be detected like microsoft usb sync
3. use mtty try difrend versions becuse sometimes 1.42 does not detect it properly - read here for what to do with mtty
IMO this may be battery problem or nand chip problem - in both cases it is hardware fail
Hi ! I have a problem with my Kaiser ! The screen is black, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays black ! Is there a way to make my kaiser working ? (Sorry for my english)
Remove battery and then press power button 30 seconds or more.
Worked for me.
Assface said:
Remove battery and then press power button 30 seconds or more.
Worked for me.
Click to expand...
Click to collapse
it doesnt work ! I think there is a problem with spl , because this problem appears after unsuccessful hard spl installing ! I don know how to fix this
IP13 said:
Hi ! I have a problem with my Kaiser ! The screen is blank, the device doesn't turn on ! But when i hold the power key & soft reset hole at the same time,
green light comes on, but the screen stays blank ! Is there a way to make my kaiser working ? (Sorry for my english)
Click to expand...
Click to collapse
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
krouth said:
Not trying to oversimplify things, but is the device fully charged? Did you have any problems during the flash? Which SPL did you flash? Have you tried a hard reset? Can you get to the bootloader screen to verify the version of SPL installed vs. the version you tried to install?
Just a few questions to help us try to figure out what is going on. Take care!
Click to expand...
Click to collapse
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
IP13 said:
The device is fully charged ! The problem was when I tried to install hard spl ...the screen stuck and I made a reset ,after this the phone ca not be turned on and all I see is green light.
I can not get to bootloader screen , when i try to turn on the device the screen i black (blank) but the green light is on
Click to expand...
Click to collapse
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
krouth said:
How are you trying to get to the bootloader screen? Have you fully read through this thread:
http://forum.xda-developers.com/showthread.php?t=533976
Finally, I would recommend downloading the original ROM and installing it. The ROM for the Tilt is here:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
That is straight from HTC's website, and you might look to see if your specific phone is there. You should be able to download it, connect your phone with the USB cable and run the downloaded file from your computer to bring your phone back to it's original state.
If that works, I would then re-read the link above thoroughly and give it another shot. Hope this helps!
Click to expand...
Click to collapse
Active sync doesnt recognize my Kaiser!
IP13 said:
Active sync doesnt recognize my Kaiser!
Click to expand...
Click to collapse
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
krouth said:
When you try to run the original HTC ROM installation program (from my previous post) with your phone connected - does it recognize your Kaiser?
Click to expand...
Click to collapse
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
IP13 said:
no,it doesnt recongnize my kaiser ! when I connect my kaiser via USB Windows says that i have conected a "ZTE USB Modem 6000 CDMA 1x"
Click to expand...
Click to collapse
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
krouth said:
I am not asking what Windows thinks you have connected, or whether or not ActiveSync sees the device. What I am asking is: When you run the original HTC ROM installation program:
"RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe"
downloaded from HTC's website, is that program able to see your phone and go through the installation process?
Click to expand...
Click to collapse
I cant install this rom because it shows me an error : "ERROR [260] CONNECTION
The Update Utillity cannot connect your PDA Phone . Please check that your USB cradle/cable is connected properly between the PC and your PDA phone .
Chech the following :
1.The PDA Phone is connected to the USB cradle/cable.
2.The USB cradle/cable is connected to the PC "
I have allready checked the cable (it works with my other PDA)
delower10 said:
Uninstall Ur Active synce And Install Again .
Then Put Ur Phone In Bootloader Mode I Hope Work Fine
CHK And Post Result
Click to expand...
Click to collapse
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
IP13 said:
I cannot acces bootloader mode , when I am pressing keys to acces bootloader mode the phone screen is still black /blank .
Click to expand...
Click to collapse
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
krouth said:
To access bootloader, you should hold down the camera button (on right side of phone) and the use the stylus to press the reset button (on bottom of phone.) When the phone goes blank, release the camera button.
When you do this, do you still get the blank/black screen?
Also, did you follow EACH step in the following thread:
http://forum.xda-developers.com/showthread.php?t=433835
Click to expand...
Click to collapse
Yes ! I also get the blank screen after following all this steps !
IP13 said:
Yes ! I also get the blank screen after following all this steps !
Click to expand...
Click to collapse
I am not sure.... I have done some searching and ran across this thread:
http://forum.xda-developers.com/showthread.php?t=423486
It has numerous posts about problems people have experienced flashing - maybe you might get some insight there - or at least post your question there where more people might be monitoring the thread. Good luck!
Please take your issue to the right place, better than open a new thread, I sugest
http://forum.xda-developers.com/showthread.php?t=433835
Your situation should be taken by the right guys, not just gessing if this or that might solve the situation, male a post there
Also have a look at the sticky on the top, try to get Dave Shaw help
THx I will try to ask there ....
Fanning the flames.
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
tyler51773 said:
Okay if you can't access the boot loader then you need to go higher up. I think the chain is Radio Rom, then SPL, then OS. Basically your SPL is gone, that is why your screen is black and you can't get into the boot loader --- cause its gone. So no duh, it can't load the OS. So, your only hope is that your radio rom is working so you can access the phone via cmd interface programmed within it.I really don't know what i'm talking about, but I've bricked my phone too and with some guidance (er explicit instructions in chat) I was (er she was) able to fix it [my situation was far more complicated with a "security locked" device, and a "radio from hell"]. Your key words are frankenkaiser. which you can find here:
http://forum.xda-developers.com/showthread.php?t=394584
Good luck, if you can get into the oemsbl I'm sure your in business. If your feeling nervous bust out the paypal and head to irc.freenode.org #xda-devs {albeit someone will likely help you without the donation but for real your going to hold someone up for an hour or two you should throw them atleast 20$ to save u 200$ }
Click to expand...
Click to collapse
Thx man , appreciate this !!
Hello!
I killed my PDA-it. 3 Color does not load mode. With or without the battery I found some 3 types of drivers shown in the picture. Not associated with MTTY, absolutely dead. : (
I'd be happy if you share with me some trick for possible recovery.
Thank you!
How did you brick it??
Do a search for QC diag drivers or MotoQ drivers install them.And download mtty.When the driver is installed check which port the diag driver is installed on and connect mtty to that port,then type cego a the type task 8 (this should reboot it.
press n hold camera & soft reset button. tri colour screen wii appear
Is dead "MTTY" and I want 3 types of drivers. MTTY claim 3 colors mode. Not associated with PDA. I have another PDA operating "Cruise" which is associated with "MTTY" without a problem. Will try with this kind of drivers: "MotoQ drivers" will tell the result.
Thank you!
the hard reset procedure is holding gps and internet button pressed for 2 seconds and without releasing them stick your stylus into the soft reset hole.
keep those two buttons pressed until the grey screen appears then release them and press the green button for confirmation and the green button again after it's done to reboot
Try to remove the battery and cable, wait 1 minute, insert the battery and start the device with pressed camera button.
When the tricolor appears plug in the cable, wait for USB message on your device and flash.
Dark Dragon
I have similar issue.
have a polaris whcic i can not make HR
tried almost everything.
Has HTC original rom but is stucke at alignment screen.
Need to make HR.
Tried camera+reset makes soft reset
tried gps+explorer makes SR
I can acess it trhoug active sync, can it help to make HR?
rpsilva said:
I have similar issue.
have a polaris whcic i can not make HR
tried almost everything.
Has HTC original rom but is stucke at alignmen screen.
Need to make HR.
Tried camera+reset makes soft reset
tried gps+explorer makes SR
I can acess it trhoug active sync, can it help to make HR?
Click to expand...
Click to collapse
i think if you see the calibration/alignment screen...windows recognizes the phone and usb and you can reflash the rom
martinasa said:
Is dead "MTTY" and I want 3 types of drivers. MTTY claim 3 colors mode. Not associated with PDA. I have another PDA operating "Cruise" which is associated with "MTTY" without a problem. Will try with this kind of drivers: "MotoQ drivers" will tell the result.
Thank you!
Click to expand...
Click to collapse
i ave in the past a similar problem....mtty did not recognizes the phone and usb...the solution for me was to start the same on a older windows xp pc...
Hello again.
Phone not come in 3 color mode.
martinasa said:
Hello again.
Phone not come in 3 color mode.
Click to expand...
Click to collapse
also not with: press n hold camera & soft reset with stylus ..?
what it makes after you start the phone..'?
Ok I had the same problem. Now i can enter in 3 colors. Make this:
Step 1. Download and read this:
http://forum.xda-developers.com/showthread.php?t=393337
You need motorola Q drivers and a Windows XP 32bit to work.
Step 2. Read the post of jpg001 of this link:
http://forum.xda-developers.com/showthread.php?p=5515006
You need use the files of jpg001 to work
Step 3. You need a mtty called "mtty_0513_Test.exe" because other version freezes, at least for me. If you need more information i will be here. I'm trying to Hard-SPL my Polaris to work.
[email protected] said:
i think if you see the calibration/alignment screen...windows recognizes the phone and usb and you can reflash the rom
Click to expand...
Click to collapse
the problem is that I do not have hardspl installed yet.
have flashed with original rom but the problem remains.
The main issue is that at boot is stucked at "tap the screen..." and want to make HR to see if helps.
Tried to install Hardspl but always an error and stays at 0%
I am assuming hardware problem with touch screen....
If you can help...
rpsilva said:
the problem is that I do not have hardspl installed yet.
have flashed with original rom but the problem remains.
The main issue is that at boot is stucked at "tap the screen..." and want to make HR to see if helps.
Tried to install Hardspl but always an error and stays at 0%
I am assuming hardware problem with touch screen....
If you can help...
Click to expand...
Click to collapse
than i think you also must use mtty (reset the phone)....from post above or here:
http://forum.xda-developers.com/showthread.php?t=425922
the best is to use windows xp for that
luzbel_es said:
Ok I had the same problem. Now i can enter in 3 colors. Make this:
Step 1. Download and read this:
http://forum.xda-developers.com/showthread.php?t=393337
You need motorola Q drivers and a Windows XP 32bit to work.
Step 2. Read the post of jpg001 of this link:
http://forum.xda-developers.com/showthread.php?p=5515006
You need use the files of jpg001 to work
Step 3. You need a mtty called "mtty_0513_Test.exe" because other version freezes, at least for me. If you need more information i will be here. I'm trying to Hard-SPL my Polaris to work.
Click to expand...
Click to collapse
very interesting....very interesting
[email protected] said:
very interesting....very interesting
Click to expand...
Click to collapse
Thank. 1 long week reading posts...
Now I'm flashing Oficial rom and seems to work!! It will revive !!
Ok! It's finish and work!! My polaris back to life!!
Original Title: what is the solution <<>> cotulla
Hi guys
I was trying to upgrade my I mate Jam to HTCMAG_ROM_WWE_O2
I followed the instructions but after the hard reset the screen stay on USB and down there is v1.00 and nothing else, On my PC its only shows please wait and dont remove or dissconnect >>etc.
what is the solution with it,
regards
By the way where I can be back to the old version ,,
Which OS do you use on your PC?
Vista and 7 did not work for me. Only Xp.
orbN said:
Which OS do you use on your PC?
Vista and 7 did not work for me. Only Xp.
Click to expand...
Click to collapse
Yeah that was the problem,, I use WIndows 7 on my labtop,,
I tried at home using XP it worked but now the problem is showing on the screen as follows :
HTCMAG_ROM_WWE_3
by Cotulla
64RAM
Bad Radio
I tried to hard reset using contacts and calender with softreset it tells to press the green blah blah..
I did and still the same.
I tried to install any other upgrade else than WWE_3 but nothing
Help please;
Hi,
install the required radio 1.12.
So long,
MrFX
MisterEffiks said:
Hi,
install the required radio 1.12.
So long,
MrFX
Click to expand...
Click to collapse
Can't do anything. when I hard reset it shows the USB and version blah blah then it restart again..
I tried to install the original rom and any other rom but same problem.
if connected to the computer via USB it keep restarting over and over
and other solution ??
will Bootloader help ? I tried but it is still the same issue.
torontovka said:
Can't do anything. when I hard reset it shows the USB and version blah blah then it restart again..
I tried to install the original rom and any other rom but same problem.
if connected to the computer via USB it keep restarting over and over
and other solution ??
will Bootloader help ? I tried but it is still the same issue.
Click to expand...
Click to collapse
I'm Having the same problem, so please if anyone know the solution please post it here...
Thanks in Advance...
torontovka said:
Original Title: what is the solution <<>> cotulla
Hi guys
I was trying to upgrade my I mate Jam to HTCMAG_ROM_WWE_O2
I followed the instructions but after the hard reset the screen stay on USB and down there is v1.00 and nothing else, On my PC its only shows please wait and dont remove or dissconnect >>etc.
what is the solution with it,
regards
By the way where I can be back to the old version ,,
Click to expand...
Click to collapse
Hey I came up with a solution, worked for my device hope it would w0rk for y0u either...
Anyhow, when it shows usb/cable at the top and radio version at bottom, Press and hold Contacts and calendar button and press Reset button with your stylus, this will hard reset your device and will bring your device alive...
looking forward for your reply...
HaSnAiN.ZaiDi said:
Hey I came up with a solution, worked for my device hope it would w0rk for y0u either...
Anyhow, when it shows usb/cable at the top and radio version at bottom, Press and hold Contacts and calendar button and press Reset button with your stylus, this will hard reset your device and will bring your device alive...
looking forward for your reply...
Click to expand...
Click to collapse
just want to help to straighten !!
i-Mate JAM hard reset
To perform a full reset
A full device reset clears memory, deletes all data and restores the Pocket PC Phone to its default settings. Programs installed at the factory remain, erasing all data that you have created and programs you have installed. Press and hold the power button, and then use the stylus to press the soft reset button at the same time. Be sure you have backed up all your data in a SD card or on your PC before performing a full reset.