hi, i have a g3 prophet with ipl ver. 1.00 and spl ver. 1.00.0000
i've just upgraded to pdaviet 4.0.0.4 PV and everything works flawlessly. however, due to wifi connections dropping i upgraded my phone's radio firmware from 1.13 to 2.19, the known version without bug with the pdaviet firmware.
installation is flawless but now my prophet can not boot , i just shows the dopod screen and resets continuosly. please help
i tried reupgrading with the newer radio version, but the installer said that it can not install, eventhough i have put my prophet in the three colour screen (bootloader) help me
You tried to restore old radio to phone , if not .
TOLD me ! i help u !
i dont have the old radio installer, it is 1.13 and can't find it anywhere.
also, i tried to upgrade to newer radioand reinstall rom, but the installer can not recognize my dopod, altough i have put it in the bootloader screen and connect it via usb.
it says error [300], invalid update tool. i have tried the 2.69 radio, 2.19 radio, and even the AKU 2.2 installer, and all of them return the same message.
please help
Related
Hi!
It's the first time I'm posting here, but after some days of search, I've found a lot about upgrading / downgrading, but nothing about my problem.
I've an MDAcompact / T-Mobile PM10A / Austria and tried to upgrade to BigStorage-Rom according this thread: " Magician to 1.13 + 1.13 Radio + BigStorage ALL-IN-ONE Guide ". I've backed up my original Rom, but after the flash, there was no radio-stack at all (booting device: "no GSM" on display).
I've tried to update the radio-stack again - error message: 114 - error upgrading radio-stack, the same with 1.12 and 1.13. I've tried to downgrade the rom to 1.12 - ok, but no radio-stack. I've tried to restore the original Rom via SD-card in bootloader-mode - device says: not allowed.
Can anyone help me?
Thanks in advance!
did u try to use an origional rom? i mean a non Bigstorage rom upgrade ? because that should fix the problem ( atleast i think it shoud)
Try Downloading the origional t-mobile1.13 rom and upgrade ur device using that install file . If i am not mistaken the first thing that is upgraded is ur radio stack then the extended rom and finally the operating sytem ( if u upgraded u would see that it does it in 3 steps).
I've tried that. As soon, as I upgraded to the original rom from T-Mobile, it stopped at the radiostack-upgrade. After that, I opened the "original".exe-file from T-Mobile with winrar and tried to upgrade again, but without the "radio.nbf"-file, what was no problem. After that, I tried to update with the "radio.nbf"-file (stand alone) again, but the "error 114"-statement came up again.
I got this error before, but only because I flashed my device with the wrong ROM.
(...I once misread "Universal" as a meaning and not as a device codename, and flashed the wrong Radio stack. Thing worked, but radio invalid, no phone capabilities. Fortunately, a reflash with the correct radio ROM found here saved me. And my $300 investment. -.-)
Either the radio part of the ROM's accidentially corrupted (download again), or the radio driver is incompatible with your device hardware. I'm not aware of Minis being avaliable in anything other than GSM tho...
I downloaded the original rom-version from the official T-Mobile website. Fact was: up/downgrade of the rom itself "ms_.nbf/nk.nbf" no problem (I've extracted the exe-file via winrar to a folder and made that several times to up/downgrade), but update of the radio-stack "radio_.nbf" not possible, ended in error 114. The point is: as soon as I start the update-utility, it shows the "Device CE Image version", "Device Extended Image Version" but no "Device Radio Image Version", it looks like no radio-stack is installed at all.
I got that exact same error through the aforementioned Universal ROM debacle (-.-). Radio failed to flash, no radio at all.
There should be a standalone radio stack somewhere in the FTP for magician. I know I saved mine with the 1.12.00 version. Try flashing with that, there's a file inside that allows you to bypass the version detection IIRC (which allows a from-scratch flash). Flashing a standalone radio stack will hard reset your system, but otherwise will not touch anything else.
hi all,
I installed 5._Underground_edition_Crossbow_ROM.exe
on qtek 9100 for tmobile.
Before installing this rom I installed custom_ruu_wizard_1050412....... bin and unlocked CID and phone.Now after successfully installed 5._Underground_edition_Crossbow_ROM.exe, I cannot make a call and I cannot sync with active sync v4.5. What should I do? How do I make activesync work sothat I can try another ROM? Whenever I try to goto phone or activesync setup it gives me error "a problem has occured with device.exe".
Please help me out.....
before update
IPL : 1.08
SPL : 1.08
OS : 1.8.10.2
after crowbow update
IPL : 1.01
SPL : 1.01.0000
OS : 10.1.6.811
my mistake was I didn't update my 9100 to 2.26 before updating to Crossbow.So looks like communication cab has been not installed.Is there any way my 9100 can communicate with Activesync?
thanks in advance.
u shd hv read the threads here and then updated it..to upgrade to wm6 underground edition u shd hv SPL greater than 2.xx..due to which GSM is not flashed as it has 2.47 version..u need to upgrade now to a rom which has SPL 2.xx and then do the underground edition
but how do I upgrade ? ,because when I connect usb cable to the phone nothing happend. i.e. activesync cannot start.
You should take time to read and search the forums. There are numerous posts with similar issues...
You need to get to the bootloader. Turn off your phone, then hold down the camera button while you turn it on, and you will be at the rainbow (bootloader) screen. Now you can flash.
Read the thread by Dr. P in the Wizard Upgrading forum. You have to follow every step exactly as it says (the last step is to upgrade to a 2.x official ROM).
thanks mfrazzz, you saved my $200, I installed 2.26 rom and then upgrade and now its working like a charm.
Thanks once again.
Hi
I have downloaded several radio rom from wiki and when I run the .exe file it shows my version is 1.2.0 image and it will upgrade to v2.47.21 etc. but when I go to my pda to check the rom version it's not 1.2.0, it's
Radio rom V02.19.21.
Protocol version 4.1.13.09
Ex Rom 2.15.13.121
Why does the program not show the correct rom version, will it damage my pda as I try to upgrade the rom when I had version
IPL 1.00
SPL 1.00.0000
GSM 01.13.20
OS 1.0.13.21
It's stop the battery from charging.
Also since the upgrade from 1 to v2 I get a blank screen when I reply to SMS, couldn't find my phone provider with auto config as the Dopod is from Singapore and I am using it in Hong Kong.
Thanks
The installer used for flashing the radio rom is "hacked". that's why it displays incorrect info. Just proceed witht he install and you should be fine.
I can't help you with your sms issues...
Hi there.
I wanted to update to the latest ENG rom on my S200, downloaded it of MyQtek, but when i tryed to upgrade, it said "Wrong Vendor ID". After a search i found that had to update first with Aku 2.2 NVID, done that.
Then i tryed again, and it said the same, then i took the nk.rom from the original package and replaced the same on NVID package, and it did the upgrade, but now i have:
IPL 2.10
SPL 2.20.000
GSM 02.47.21
ROM 2.20.7.34
Where is the upgrade ?!
I downloaded the latest official radio ROM version for my prophet and ran the utility just as the wiki suggested, with the result that my radio ROM is totally gone and my device doesnt start... remains stuck at the club i-mate splash screen for a while and restarts, continuing over and over... my IPL is 1.00 and SPL is 1.00.000 with no GSM/radio version showing up
help please
Did you used the correct update RUU (for you it must be a G3 update RUU)?