Related
Hi,
I've got a problem with my carkit (O2 XDA-Carkit) after I upgrade to the new ROM-Version of T-Mobile (1.60).
With the old Rom-Version, the carkit works as a loadspeaker for all kind of sound. The voice-instructions from tomtom for example, came out of the carkit-speaker loud and clearly. Each kind of sound, the device made, came out of the speaker of the carkit.
Now, after upgrading to the new ROM, only the telephone works with the speaker of the carkit. With Incoming or outgoing calls I can use the carkit as usual...the speaker works and the mikro works also. But every other sound (e.g. tomtom voice-instructions) came direktly out of the speaker of the mda2 in a poor quality.
Some hints, how I could use my carkit again as a speaker for all kind of sound without goinig back to the old ROM ?
Any other kind of hints...maybe to use a bluetooth headset therefor (so that all kind of sound came out of the headset....not only telephone...I've got a Plantronics Headset...but also only the telephone works)
thx for help
best regards
rob.
Yep.......I have the same problem here.......don't know why they changed settings on the handsfree profile here.
Another thing you will find out is that the charging is very slow on the XDA carkit with the XDA II. If you run TomTom, Yeti and a bright screen the xda II will not charge, but drain!!
It has something to do with the wiring of the interface, but unless someone will come up with a solution I will go for a new carkit or a BT solution. (It's a bloody shame though it doesn't work properly with the XDA carkit! :evil: )
Hi,
the charging-problem is also a mess.
I think, the problem is only the GPS-driver from tomtom. In my tests, only when the GPS-driver is loaded, the battery-power goes down. With stopping the GPS-driver, the battery will charge again, but only, if the battery-power is more than about 75 - 80%.
If the battery is less than 75%, it will not charge at all, even if, there is no App runnung and the screen is off.
You said, you will go for a new carkit or bluetooth-solution. Do you know a carkit or bluetooth-solution, wich offers the feature, that all sounds (tomtom instuctions...etc.) came out of a loadspeaker or thru a headset (without connecting the wired headphone ;-)
As far as I know, at the moment all devices works only with the telephone-funktion....
best regards
rob.
Same here,
i have build my own carkit, and have put ground to pin 19,
sound was normally going though the connector to my car stereo
now it doenst anymore :evil:
I am sure this isnt a hardware thing it is software
could be the settings on the handsfree profile. on the xda2...
this is very very frustrating. just being finished with my carkit and now i cant use it anymore
also you cant set the phone to speakermode anymore..
I am sure this isnt a hardware thing it is software
could be the settings on the handsfree profile. on the xda2...
Click to expand...
Click to collapse
Does anybody know how to change this back?
I found that the registry points to a certain file in your windows directory: HandsFree_Dll.dll
(I found this here: HKLM\Services\Handsfree)
Can someone with the old 1.03 ROM please upload this file so i can try if this solves the problem...
TIA,
Max
Akira, Max :
I am building my own car kit, and have no success.
I do not obtain audio out with or without grounding pin 19.
I'm running Rom 1.60.00WWE.
Did you solve your problem ??
I must correct my last update.
I obtain audio when in phone mode, but not during playing waves or TomTom directions. Even Ring Tones do not go out trough the bottom connector.
So is it a software problem ?
Can it be corrected ?
hello i have a HBH-DS 970 sony and it work good but i have a probleme and i know that i am not alone .
when the heaset is detected the phone purpose handfree and wireless stereo if i put handfree and wireless stereo i don t heard the ring on the phone only on the headset if i put only handfree the ring is on the phone (very good ) but when i want to listen music i must be configurate bluetooth et put wireless stereo to .
nobody can make a today plugin to have choise handfree or wireless stereo on the today screen.
thanks to your comment sorry for my english
sud the little frenchy
sud, this is a problem for all of Windows Mobile. The best solution I have is to put a BT icon somewhere on your today screen, so that at least with one click you can get to configuration and set "wireless stereo".
I usually put the BT icon in my system tray.
Funny, my Wizard will switch between handsfree, and stereo headphones when there is a call, or listening to music on my DS970 with no problems. I don't need to do anything.
Doesn't do it on my Universal though. As he says, you have to manually switch.
I am guessing there is a registry setting or 2 somewhere that will resolve this.
thanks for your interested for this probleme.
the bluetooth icone can be put on today screen but i search a solution for put an icone handfree and an other wireless stereo or like said alanJC maybe in the registry.
to be continued
@AlanJC: I understood the problem to be... well, the problem that I have! Maybe I misunderstood. It's not that if you are in 'wireless stereo' for music you can't auto-switch to 'hands free' for voice, and back again. It's that you have to set 'wireless stereo' in the first place, whilst 'hands free' seems to work by default.
@sud: I've never seen the Today icons you are looking for... and I've looked too. Great idea. PLEASE post here if you find them.
http://www.teksoftco.com/index.php?section=freeware here is the soft to switch but with the last rom is ok without it
Hi,
I am using O2 xda mini s, and i just bought a sony ericson HBH-DS970 stereo bluetooth earphones.
I am using WM6 Xplorer Rom and radio version 02.25.11.
Currently I am a bit frustrated with my bluetooth earphone as the quality is very poor eventhough I read that the quality of the sound if used with other bluetooth handphone / pocket PC is superb.
I have ben searching this forum to either tweaks the registry or any patch to improve the sound but currently I'm still lost. I found one old post (WM5) which guide us to tweaks -> HKLM/software/microsoft/bluetooth/a2dp/settings....
but my problem is that there is no settings folder under my a2dp, there are 4 folder with label 1,2,3,4.
Are there any way i can improve the sound quality???
will changing the radio rom affect the quality of bluetooth reception??
Please enlighten me..
Thanks
http://forum.xda-developers.com/showthread.php?t=297762&page=100
Try the settings from cduncan...
If there is no registry entry, you will have to manually put them.
You can change the bitpool setting for quality of music.
HTH
Cheers Sids,
I have already do as you said... previously went to that post but feel lost, and since the thread have over 100 pages, therefore i feel inappropriate to ask you or duncan.
One more thing though, can i ask you what is your personal preference on those settings?? I cant put a lot of bass, because it will sound terrible, like broken speaker.. what todo??
cheers mate
p/s My problem is that the quality of the sound that coming out of my BT earphone is just poor (although others are highly recommending this DS970). I have no problem with pairing it with my wizard or the playback.
I have play around with the BitPool and the only difference that I notice was the volume level, not the sound quality. any advice??
One more thing, is the selection of Radio Rom have any effect to the quality of the bluetooth signal i.e. to the output in my BT earphone??? Help...
Thanks again
Hi,
I cant say about your BT headsets. But I confirmed these things - Updated firmware from the manufacturer (Jabra for me) and the quality with other A2DP enabled (maybe nokia/SE) phone.
I have set my bitpool setting to 60 which is Farias default, but he placed the reg entry in AD2P folder instead of A2DP by mistake.
I am using equalizer settings with TCPMP for the nice sound, which I dont get with Windows Media Player. Maybe you could try that out.
Even after those settings and tweakings, I dont think BT headsets can replace wired headsets for an audiophile. You will only just get passable sound quality. Maybe its got to do with bandwidth that BT provides.
Lastly, I may be wrong, but Radio roms are only used for GSM radio. Its got nothing to do with BT.
Gurus, please correct me if I am wrong anywhere.
Sid
I'm using faria ROM Real Thing and using Oakley OROKR as my bluetooth stereo. But I have unusual problem. When I listen MP3 from pocket music 4.3.4 my OROKR produced a lag sound. Sometimes the sound was disapeared and suddenly back to normal again (with lag of course). I have try my OROKR with my PALM Treo 650 using A2DP s/w it's produced same quality like my MDA. Is this happen cause the registry setting or my OROKR problem? Help me?
PS: If I used OROKR to call it's 100% normal
For what it's worth, i have tested my plantronics pulsar 590a (bt ver2) with other htc devices with bluetooth ver 2 and audio was excellent. the wizard only has bt ver 1.2 and that is maybe where sound quality is lost. just a thought...
did you buy the headphones on ebay? Got mine on ebay and I was very disappointed with the sound quality. i checked online and, for my surprised, i discovered that what I got from ebay was a cheap fake. I bought a new set from sony shop and voila, they work perfect. Sound is amazing..with the SE k800i i am using from time to time. Couldnt get them to worjk with my xda2i tho
Hi all,
Laurentius and I are looking at resolving the current issues with A2DP (Many fixes will be in our latest rom, however issues vary from headset to headset.
Some work fine, others are poor quality and some receive PDA lockups or long pauses between streams.
Please could those with A2DP issues, and the need for this protocol to work properly, post the following information.
The current Rom you are you using
The make and Model of your headset
A list of issues you are currently having with A2DP.
Please also try the following to resolve the issue.......
HKLM\Software\Microsoft\Bluetooth\A2DP\Settings\
Remove (Delete the following entries)
BitPool
MaxBitpool
and add the following
[HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\AudioGateway]
"Capability"=dword:0000003C
[HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\A2DP\Settings]
"SampleRate"=dword:0000BB80
"UseJointStereo"=dword:00000001
Please then remove (un-pair) your headset and Soft Reset
After SR please re-pair Headset and test A2DP again.
Please keep this thread clean and only post A2DP issues with the required information listed above.
Thanks,
Cheers,
Beast
Hi Beast,
Isn't:
"UseJointStereo"=dword:00000000
to get proper stereo sounnd?
Regards,
KOR!
I have latest V1 rom from Lt.Cmdr.Ivan - BT headset is Philips SHB7102 (works great with my Wizard and SEk800i). I did exacetely what U have asked for (but i have left jointstereo=0) and nothing happend. It sounds like 2s of music folowed by 15s of silence, then again 2s of music and 15s of silence. I messed with bitpool walues and couldn't find any working set. I'm afraid that's something wrong with max BT speed and not with A2DP implementation. I had BT speed switch app when I used broadcom BT stack and A2DP works great. Unfotunatelly normal mono BT headset doesnt work at all with this BT stack so I'm back to original stack
jarekt said:
I have latest V1 rom from Lt.Cmdr.Ivan - BT headset is Philips SHB7102 (works great with my Wizard and SEk800i). I did exacetely what U have asked for (but i have left jointstereo=0) and nothing happend. It sounds like 2s of music folowed by 15s of silence, then again 2s of music and 15s of silence. I messed with bitpool walues and couldn't find any working set. I'm afraid that's something wrong with max BT speed and not with A2DP implementation. I had BT speed switch app when I used broadcom BT stack and A2DP works great. Unfotunatelly normal mono BT headset doesnt work at all with this BT stack so I'm back to original stack
Click to expand...
Click to collapse
I've found that with MS stack and my Jabra BT620s the best bitpool is 33... good quality and good range (no interruptions)... jointstereo must be 1 otherwise the sound uses too bandwidth...
jarekt said:
I have latest V1 rom from Lt.Cmdr.Ivan - BT headset is Philips SHB7102 (works great with my Wizard and SEk800i). I did exacetely what U have asked for (but i have left jointstereo=0) and nothing happend. It sounds like 2s of music folowed by 15s of silence, then again 2s of music and 15s of silence. I messed with bitpool walues and couldn't find any working set. I'm afraid that's something wrong with max BT speed and not with A2DP implementation. I had BT speed switch app when I used broadcom BT stack and A2DP works great. Unfotunatelly normal mono BT headset doesnt work at all with this BT stack so I'm back to original stack
Click to expand...
Click to collapse
I also have Ivan's V1 Rom and have an Itech Radio headset. I completed the changes that you suggested and found that A2DP works well it did before the changes too. I have noticed that the sound quality may be a little better and the pauses are slightly reduced.
The main problem I have found with A2DP with all AKU0.5 ROMS is the pairing of the headset. If you soft reset you phone while the headset is on, A2DP will be auto detected when the phone comes up. If you play music then the music starts and stops and the phone becomes unstable. The work around is to turn your headset off, soft reset the phone. When the phone comes up turn the headset on and activate A2dp by pressing the button on the phone. Music then plays fine.
The registry changes you suggested did not help the above problem. AKU0.5 ROMS all seem to have this A2DP autodetect error on reset at least with my headset. Very frustrating.
gewin said:
I also have Ivan's V1 Rom and have an Itech Radio headset. I completed the changes that you suggested and found that A2DP works well it did before the changes too. I have noticed that the sound quality may be a little better and the pauses are slightly reduced.
The main problem I have found with A2DP with all AKU0.5 ROMS is the pairing of the headset. If you soft reset you phone while the headset is on, A2DP will be auto detected when the phone comes up. If you play music then the music starts and stops and the phone becomes unstable. The work around is to turn your headset off, soft reset the phone. When the phone comes up turn the headset on and activate A2dp by pressing the button on the phone. Music then plays fine.
The registry changes you suggested did not help the above problem. AKU0.5 ROMS all seem to have this A2DP autodetect error on reset at least with my headset. Very frustrating.
Click to expand...
Click to collapse
Sorry I meant to say " When the phone comes up turn the headset on and activate A2DP by pressing the button on the HEADSET."
mamiware said:
I've found that with MS stack and my Jabra BT620s the best bitpool is 33... good quality and good range (no interruptions)... jointstereo must be 1 otherwise the sound uses too bandwidth...
Click to expand...
Click to collapse
Hi Maniware,
Can you please further shed light in detail on the jointstereo?
Why jointstereo to be 1 or 0?
Thanks in advance!
KOR!
It goes well with joint stereo. Seems that it needs much less bandwidth. I've heard that jointstero=1 means that there is mono sound in effect.
"UseJointStereo"=dword:00000001 << mono
"UseJointStereo"=dword:00000002 << joint stereo
"UseJointStereo"=dword:00000000 << stereo
AFAIK
qtek 9000 - Logitech Mobile Bluetooth Headset
I'm not quite sure if my problem is right here - because i still have the original (last build) WM5 ROM (130.96 GER, Radio 1.09.00, ExtROM 1.30.185 GER).
I encounter statics while using the Logitech bluetooth headset, which is a mono one, making phone calls impossible due to stressed phone partners ... Only the person on the other end of the line encounters interruptions, me, as calling, not.
This is the main issue for me to update the ROM, and I'm trying to find out if any of your nice new ROMs will be of help.
Anyway, I haven't tried yet I'm afraid to destroy my device ...
thanx
Anna
my feedback:
device:
itech r35
Problems:
sound muted after 2 seconds of music.
audio players used:
audio manager
windows media player
i tried your advices, but not worked for me....
Sometimes it works when i put 70 (binary) on both Maxbitpool and bitpool...but on next device activation or reboot it just stop working...
A2DP and wireless
Just to be clear, my results are when I do not have wlan activated.
I changed UseJointStereo=dword:00000000.
Quality is good and it is definitely stereo.
Still have the auto detect problem. Interesting though, if I walk out of range for a while with the headset on, when I come back into range the A2dp is autodetect and the music starts playing through the headset again, quality is good. If I soft reset with the headset on and A2DP is autodetected, the headset is unusable.
If you do any of this with wlan on the quality is very poor with starts and stops.
Also noticed that audio manager does a better job with bluetooth than gsplayer, I think audio manager may have better caching.
Freezing
I think there's a problem with the latest core os files (AKU 0.7.0)... i havent' tried the MS BT stack, but with the Widcomm, using the bluetooth for anything more than 1 min, completely freezes the phone.
It does when listening music, transferring files, etc... if BT is idle, nothing happens (except than freezing the device when the Comm Manager gets confused and enables BT instead of gsm radio).
So it seems related to the core files.
Switching on and off, transferring data thru BT is a critical task and subject to lockups.
For the record, i used to use the BT A2DP and file transfer without ANY problem whatsoever in my old and horribly-underpowered HTC Tornado (omap850 @195mhz) so IT MUST WORK!
im using your latest rom and Motorola HT820 does not have a problem with it... even in the earlier roms you cooked... even tried it in indra's xoj version and darkforce's rom..
just wanted to clear it out just so you can rule something out...
rnzk8 said:
im using your latest rom and Motorola HT820 does not have a problem with it... even in the earlier roms you cooked... even tried it in indra's xoj version and darkforce's rom..
just wanted to clear it out just so you can rule something out...
Click to expand...
Click to collapse
Hi,
Now that sucks,
I have the same headset HT820 and audio sucks, long pauses etc etc.
Can you post your firmware Revision for me please, it should be printed on the inside of the headband.
Cheers,
Beast
Haha.. can you help my friend Beasty please
He's so happy with his new headset.
rofl......
Cheers,
Leo
@Beast J.K.
rnzk8 said:
im using your latest rom and Motorola HT820 does not have a problem with it... even in the earlier roms you cooked... even tried it in indra's xoj version and darkforce's rom..
just wanted to clear it out just so you can rule something out...
Click to expand...
Click to collapse
Plantronics Pulsar 260
Sound stops coming fter about 1 second of playback (used TCPM,
Audio Manager)
The same result after applying those reg mods....
Please try and install the stack found here: http://forum.xda-developers.com/showthread.php?t=291639
A2DP problems should go away, but then will come the freeze-after-1-min problems, like with my HP Stereo bluetooth headset
I've flash to your latest WM6 AKU 0.7 (WIFI Fix update 3) ROM just now. But sadly to say, the freezing thing still occurs after playing music with Audio Manager. It even freezes when watching videos using WMP. Usually around 1 minute it shall start freezing. FYI:
Bluetooth model: i-tech Clip
AnnaD said:
I'm not quite sure if my problem is right here - because i still have the original (last build) WM5 ROM (130.96 GER, Radio 1.09.00, ExtROM 1.30.185 GER).
I encounter statics while using the Logitech bluetooth headset, which is a mono one, making phone calls impossible due to stressed phone partners ... Only the person on the other end of the line encounters interruptions, me, as calling, not.
This is the main issue for me to update the ROM, and I'm trying to find out if any of your nice new ROMs will be of help.
Anyway, I haven't tried yet I'm afraid to destroy my device ...
thanx
Anna
Click to expand...
Click to collapse
I had the Qtek 9000 with italian version WM5 and i flashed WM6 with no problems. if you dont wanna have any problems unzip the attached file and add in the folder the 3 files (ms_.nbf ; nk.nbf ; radio_.nbf) from your prefered WM6 ROM (I personally use the latest Laurentius & Beast ROM http://forum.xda-developers.com/showthread.php?t=325466) start into bootloader (Power+backlite+softreset) and ROMUpgradeUt.exe
VERY IMPORTANT: you have to charge your batery before any flashing
Hi if someone can help me it would be much appreciated. I just bought a Touch Pro and everything is working fine....except for one really annoying issue.
Whenever I connect my bluetooth to a headset, it shows connected but no sound is coming out. The sound is muted. when connected to my Audi, I see that the phone has bars (shows connected and I can dial the phone), but when I make a call no sound. Similarly on my SE HBH-DS970 headset. The A2DP works perfectly, but when I make a call nothing.....I've searched google and through XDA and no solution.
Can someone suggest a solution? I've soft/hard reset the device already. If I should change Radio ROM which one would someone suggest that's stable? Thanks
If no one else has this problem, can anyone at least suggest to me if this sounds like a Hardware or software issue? If hardware I will return it, but if software I will try to find a solution. Like I said the phone connects to BT, but I just can't get handsfree to work. File transfers and A2DP work. Thanks
Just flashed to UK ROM and still no help....I've read some people having the same problems over at the Diamond thread...I'm the only one answering my own thread here hahaha....if anyone can help I'd greatly appreciate it. Thanks.
Hi,
I occasionally had such an issue with my Parrot CK3100, but I did not get the time yet to investigate further. After the call was connected I did not hear anything, and I am not sure whether the other party could hear me.
On another day, the handsfree was working perfectly OK.
Cheers
Michael
Thanks for replying Michael....I'm at a loss and I tried all the suggestions posted. I hope it's a software issue...I'm going to buy a bluetooth headset tomorrow and see if that works. It's not the end of the world, but annoying since all my ppc, s60, BB, and UIQ phones prior to the TP have not had any such issues.
Do you think it's a software issue?
have you tried playing music?
Yes.....A2DP works perfectly....no problems whatsoever with file transfers either....I'm guessing either it's a software problem or the phone has a new bluetooth software that's not agreeing with my older SE headset, but the car is another issue. The Car is 2007 and I'm sure the Bluetooth software is not that old. I've tried Euro WWE and Asian WWE ROM and no go.....I'm going to try the Cingular ROM and see what happens.
Just another quick update....I tried 2 other different bluetooth headsets and still the same problem... for some reason the sound for handsfree will not come through...anyone know of registry hack possibly that will allow sound to come through?
May not be entirely related to your problem...
Mine is worst...whenever I have paired my Jabra or iTech BT headset, when the phone rings, 8/10 times the phone will auto pickup (and no I did not setup the phone to auto pickup) and the it will NOT connect to the bluetooth. Instead it will be just like an auto pickup and the sound will come thru the phone headset. This is driving me nuts!!!!