WIFI SUspension - 8125, K-JAM, P4300, MDA Vario ROM Development

helloooo.....i hope u guys can resolve my issue w/ a registry edit or something because i have tried almost EVERYTHING...neways, at times i like to leave my wifi on (because i don't have the data plan) sooo only turn my screen off to do so....however i turn the screen off and then i turn it back on after a few minutes and wifi is gone!!!!! it makes me sooo mad....on my old hp jornada, wen i used to turn off the screen, wifi would stay connected forever (well actually unless i turn the ppc off) so if some1 could plz help me w/ this, i WOULD APPRECIATE THIS SOOOO MUCH....just a way to keep wifi from suspending!!! thnx...~kareem
so basically i don't want wifi to suspend....let it run forever and idc about the battery

I will not use the wi-fi connection in the way you mentioned because of my utter urge to conserve battery power but there is a key in the registry HKLM\Comm\TNETWLN1\Parms\HTCAutoOffWifiTime with a DWORD value of 20000 try increasing this value and see what happens??
Please do make a backup of this whole key before playing arond with it to much. I stuffed the whole Wi-Fi of my Wizard once til such an extend where I had to Hard-Reset to get the Wi-Fi going again..

hope it works
Tip-Ex said:
I will not use the wi-fi connection in the way you mentioned because of my utter urge to conserve battery power but there is a key in the registry HKLM\Comm\TNETWLN1\Parms\HTCAutoOffWifiTime with a DWORD value of 20000 try increasing this value and see what happens??
Please do make a backup of this whole key before playing arond with it to much. I stuffed the whole Wi-Fi of my Wizard once til such an extend where I had to Hard-Reset to get the Wi-Fi going again..
Click to expand...
Click to collapse
kool thnx...i put some huge random number...i'll c wat happens..however i juss want a reg edit that wont suspend wifi wen my screen is off or my screensaver is on..thnx

didn't work
kareem9nba said:
kool thnx...i put some huge random number...i'll c wat happens..however i juss want a reg edit that wont suspend wifi wen my screen is off or my screensaver is on..thnx
Click to expand...
Click to collapse
didn't work...o well thnx for the effort neways

Related

treo 750v after wm6, screen keeps turning on

anything im missing guys?
after flashing with the new ATT wm6 all works fine except the screen backlight keps coming on, even after pressing the screen off button it comes back on after a few secs.
peeps. anyone experience this?
i had the same problem
u cent stop it by turning your screen brightnes to 50% or above (using palm bult in brightness program (press function button (the white spot) + "P" ))
vladimir2989 said:
i had the same problem
u cent stop it by turning your screen brightnes to 50% or above (using palm bult in brightness program (press function button (the white spot) + "P" ))
Click to expand...
Click to collapse
woohoo! problem solved, thanks man!
My Voda WM6 works fine with backlight set to 40%
Sigh...I should have come here to see the solution first before I hard reset my phone.
I got the same problem, but I perform a hard reset to resolve it.
Guys I posted this on another thread here but I thought I'd mention it here as well just in case you guys can help me out.
I have my Treo 750v to connect to the net and check for emails every 30 minutes but whenever it does, the screen comes on!
Is there anyway I can get around this?
I would appreciate any help.
Thanks.
D.C
Dead Cell said:
Guys I posted this on another thread here but I thought I'd mention it here as well just in case you guys can help me out.
I have my Treo 750v to connect to the net and check for emails every 30 minutes but whenever it does, the screen comes on!
Is there anyway I can get around this?
I would appreciate any help.
Thanks.
D.C
Click to expand...
Click to collapse
Stupid as it sounds, this does appear to be a bug in the Treo WM6 update. It's still there in 2.23 VF as well. If you have Keyguard set to kick in at screen off and you set the brightness to anything other than 20% or 60% (at least for me) then the screen keeps turning on and often won't turn off after the 1 minute timeout. Got mine at 60% and its fine.

kjam black sleep

i think we did all sort of upgrading and hacking for the kjam, and one of the most annoying problem no one did find its solution till now.
the dead sleep screen.
for who dont know what i'm talking about, i mean by "dead sleep screen" when the device after some minutes of ur choice turn the backlight off, u expect to turn backlight on again by pressing either any button, or touching the screen or the power on, but nothing will light the screen again, and when the device go in standby mode and turn off the screen, same issue no key and no screen touch will wake it up again.
i faced this problem in almost most of the roms, and to be clear:
NO OVERCLOCKING SOFTWARES ARE USED
NO ADDITIONAL SOFTWARES ARE USED
RADIO 2.19 WICH IS PERFECT
last time i flashed my device to the new new tnt5 rom, expecting a solution for this problem but this time the problem is getting more annoying and present each time.
please if anyone have a solution, a patch file, a registrytweaking, let us know as this problem is the most killer for the device, u cant imagine that 10 calls are missed and u cant hear the ring of ur phone just because of its hibernation.
P.S.: i saw some time ago a patch file for the jasjam or jamin called "auto suspend patch" anyone tried if it's effective, and if it work on kjam, or maybe the experts have a more solid solution.
thanks for all ur support and help
Starting from ROMs using OS 5.2.1413 and changing the PagePool to 12MB, I never has the Sleep of Death problem now.
I used Underground 3.0 and now NBD 8.2 WM6 ROM, with IPL and SPL 3.08, Radio 2.69.11.
Warning.
Please try not to double post threads anymore.
I've never experienced (nor heard of) this "sleep of death" problem. When the backlight dims (but the wizard is still on) i can light it up again by pressing any key (or tapping anywhere). When the phone goes in standby, instead, i can only use the power button to start it again.
Things have been this way since the first time i bought the phone, with every rom, in any language.
@ anichillus:
sorry for that, didnt know that i have a double post, it happened accidently when i had a down connection then i refresh and resend the page, weird i think it shouldnt post it as second thread.
@risidoro:
i think u r more than lucky man, i know a lot of pplz facing this sleep from time to time, the way they missed some calls, and pplz think that they are away them.
@starkwong:
please can u tell me the easiet way to up the page pool from 6 to 12, maybe a packtool?
P.S.: i tried the followings in order to fix the sleep death screen
1- REMOVING THE SD CARD, SOFT RESET (DIDNT WORK)
2- REMOVING THE NON OVECLOACK BATTERY, CLEAN REGISTRY, SOFT RESET (DIDNT WORK)
3- CHARGED BATTRY, RESETTING THE BACKLIGHT SETTINGS (DIDNT WORK)
4- INSTALLING THE (AUTO SUSPEND PATCH) THIS FILE WORKS, AND TILL NOW I DIDNT FACE IT AGAIN, WILL CONTINUE CHECKING AND TESTING, TO SEE HOW MUCH THIS PATCH FILE IS EFFECTIVE FOR THE DEATH SLEEP.
vuedesprit said:
@ anichillus:
sorry for that, didnt know that i have a double post, it happened accidently when i had a down connection then i refresh and resend the page, weird i think it shouldnt post it as second thread.
Click to expand...
Click to collapse
No problem, i was suspecting that
To change page pool size, I recommend using the Wizard Service Tool.
http://forum.xda-developers.com/showthread.php?t=329170
Sorry I'm a bit late;
I had the Standby of Death SOD this is when the phone fails to come out of standby with a power button press. This issue only affects some people on some networks. I'm not sure if its a network problem or a software problem but as only a minority of people have it, I suspect its mainly a network problem there is a software solution.
The solution is to change the phone settings band option from auto 3G/2G to either 3G Only (WCDMA + UTMS 2100 in Europe) or 2G Only (GSM + AUTO) depending on your requirements.
Also read this thread http://forum.xda-developers.com/show...standby&page=2 where the resolution was to get a new SIM.
Obviously this only solves the problem when the crash is because of the sim and/or settings which impact the sim. To rule out a software cause its best to start with a hard reset.

weird? i think so

so heres a weird thing that happened last night. i was playing around with tornadopowercontrol and i accidently set cpu speed to ultra slow. it stayed workin for a few seconds and then turned off. got scared, i turn it back on, it loads to the main home screen, loads up tornadopowercontrol (had it in the startup mode -hidden) and then it turns off and reboots. Not sure why, maybe cause its still stuck in that low cpu speed? this continues to happen, not sure how to stop it.... any suggestions?
Try a hard reset! From the Wiki: "Turn off your phone, then press both soft keys next to D-Pad and power on device. After moment release both soft keys. On the black screen asking for confirmation press "green phone" button and wait couple minutes for phone to initialize"
Sync it and edit your Power_On.lnk inside \Windows\ and put it back to whatever speed you had it at,
I don't think he can get it to this point!
thanks a lot!!!!
I was just about to try the ultra slow thingy
prajith said:
thanks a lot!!!!
I was just about to try the ultra slow thingy
Click to expand...
Click to collapse
lol no problem ya couldn't sync it to reset it back to original settings. ultimately required a hard reset hope i have my stuff backed up somewhere! lol i tried puttin it to a lower settin cause i was just listening to music and didnt' think i needed it running at 252. but i guess 116mhz is much to low, anyone know wats probably the safest (and lowest) speed it can run at?
i had a similar problem but managed to solve it without hard reset. i powered up the phone with pc cable connected ... lucklly it was able to connect through ActiveSync before programs from startUp and i`ve managed to overwrite the file.
my vox works ok even with 140 as lower setting but SmartToolKit seems to lockup way too often ... right now i`m using 164 and i haven`t see a lockup in about a week or so.
264 seems to be the upper limit (damn rocket) , beyond that it start to act crazy.
lastOne said:
i had a similar problem but managed to solve it without hard reset. i powered up the phone with pc cable connected ... lucklly it was able to connect through ActiveSync before programs from startUp and i`ve managed to overwrite the file.
my vox works ok even with 140 as lower setting but SmartToolKit seems to lockup way too often ... right now i`m using 164 and i haven`t see a lockup in about a week or so.
264 seems to be the upper limit (damn rocket) , beyond that it start to act crazy.
Click to expand...
Click to collapse
is the 264 mhz stable? or does it lock up? anything with smartoolkit locks up i just turn it off nowadays

Programmatically disable backlight

I searched around a bit for this information but all I found was the section of the registry where you can control the backlight brightness. I also tried MBVklight but that doens't seem to do the trick either.
I'm trying to turn off/on the backlight using .NET. I would imagine it requires a P/Invoke so if anyone can point me in the right direction it would be much appreciated. I want to do this because hitting the power button disables wifi, so I want wifi to stay on but have the screen off.
Thanks in advance!
Using advanced config 3.3 you can set the wifi to stay on after hitting the power button, which is effectively what you want to do yh? It will cane your battery tho, but its useful for donloading on device
Hmm yeah that would do the trick. Thanks!
I have an old Titan that I'm no longer using so I'm turning it into a bedside alert system in case my regular phone isn't on ring and someone needs to wake me up (I'm in charge of all the servers where I work). It needs to maintain a wifi connection so it can receive the signal but it's constantly plugged in so power isn't a problem.
sorted, no problems and good idea
I installed Advanced Config 3.3 and went into Menu -> More settings -> Connections and checked "Enable Wi-Fi on standby mode" and did a soft reset but it doesn't seem to be working. If I hit the power button on the phone to enter standby the wifi light stops blinking and it stops receiving connections. Is there another setting I'm missing?
mm let me try on mine, ill get back to you.......
Any luck? It's not really a big deal since I modified my application to be full screen with a black background so it would be doing minimal burn in, but I'd still prefer if it was fully off.

TP keeps turning itself off every 30 seconds

Hi
Unless I'm actively using it my TP keeps turns itself off after 30 seconds no matter what power settings I use (and despite a factory reset and SPB restore). This isn't too much of an issue, except when I'm trying to use GPS/Satnav (TT7) whilst driving, where turning itself off is a real pain.
Could anyone please suggest how this issue can be resolved?
Many thanks in advance...
Is it physically turning off, requiring you to press the on key, let it reboot, or,
is it going to sleep, and you press the on key to wake it up?
If it is the latter, go to start>settings>system>power, click on the
advanced tab and change the backlight & power off settings there.
If it actually turning off, sounds like it might be a defective phone.
Thanks for your reply!
I've repeatedly altered the power settings but it makes no difference at all, if I set it to turn off at any given time (or not at all) it'll still turn off after 30 seconds. And to claify, it doesn't reboot, it just turns the screen off. It *feels* like a software issue, because it'll stay working forver as long as I tap the screen occasionally, something somewhere just counts down 30 seconds if i don't and turns off the screen...
The max time you can put on it is 5 min. The default setting out of the box is 30 seconds --which sound like what you currently have.
Set the "On Battery Power: Turn off backlight if device is not used for xxx MIN). Make sure first that that's checked, and select the drop down.
Eventually --to conserve battery power--, it will 'sleep'.
Your NAVIGATION software should have a setting to over-ride this to NEVER TURN OFF DISPLAY WHILE NAVIGATION.
Aside from that, there is no other way to keep the backlight on --unless it's plugged into a power outlet.
Many thanks again for your reply; As I mentioned previously I've already changed the power settings settings (frequently) and I'm definitely not on the 30-second default, no setting appears to make any difference, be it 5 minutes or 'never turn off'. It also happens when the 'phone is plugged into a power source too.
(And I have got the 'don't turn off whilst navigating' box ticked for the satnav but the issue applies generally, not just to the satnav, that's just where it's most irritating).
Is there any possibility something has changed in the registry to over-ride the control panel settings in this way?
How about doing a hard reset and not doing a spb restore? You realize that all you did when you restored the phone was restore the bug, right?
Edit: I doubt it will work, but you can try the backlight cab. It will restore all the stock backlight reg settings if yours are messed up.
timpollard said:
Hi
Unless I'm actively using it my TP keeps turns itself off after 30 seconds no matter what power settings I use (and despite a factory reset and SPB restore). This isn't too much of an issue, except when I'm trying to use GPS/Satnav (TT7) whilst driving, where turning itself off is a real pain.
Could anyone please suggest how this issue can be resolved?
Many thanks in advance...
Click to expand...
Click to collapse
Hi,
I have same problem as you. TP keeps turns itself off after 30 sec!!
And I am using TT7. So this problem is so annoying.
I tried hard resetting and install programs one by one. and check if TP is keeping backlight on or not. And I installed TT7 and worked perfect.( display is always on)
That was yesterday.
Today I was using TP, it happened again.
The registry setting is still 3min on battery, uncheck on AC power.
30 sec problem happens both status.
This thing did not happen before Raphael_Cingular_US_5.11.502.2_Radio_Sign.
TP worked fine for a while on this radio.
Now even I check " NEVER TURN OFF DISPLAY WHILE NAVIGATION" box in some apps. TP turn off backlight.
I tried backlight.cab, that did not work and still turning off.
(thanks anyway )
ATT Fuze
Raphael_Cingular_US_5.11.502.2_Radio_Sign
Added Japanese IME
Resco Explorer, regedit
Resco Today Plugin
Spb time, Today plugin
TT7
TomTom 7 - v7.910.9185
I will try hard reset again.
Somebody please help us out.
Did you try the cab? If that doesn't work, just flash another rom.
I am also having this problem. I did get it to stop once by going in to the registry and actually editing it. But it started to do it again after a wile. I am trying it again today and see if it work. I am using a trial version of BestRegEdit and was wonder if it could have changed it back because it was a trial. So if some one elce wants to give it a shot it us under HKey_Current_user\ControlPanel\Power\Display and you will change that 30 to what ever amount of time you want. I pick 0 because i never want it to turn off. Hope this helps Oyeah, does anyone know of a free resitry editor? This is my last day on the BestRegEdit Thanks
Uh, total commander, regedit, dotfred's task manager and probably a few more.
Farmer Ted said:
Did you try the cab? If that doesn't work, just flash another rom.
Click to expand...
Click to collapse
Thanx,
I tried cab, and did not work. So I installed test rom and works fine now. NO 30 seconds backlight off now.
[March 1st] New ATT test rom Radio 1.12.25.19 OS AKU 1.4.6 Build 20771
I will use this until new "Signed" and Works Ok radio comes.
* Recently I use resco explorer and regedit addon. Free app: regedit.Mrln works fine, I think. I have been using these for keyboard layout section.
Glad you solved it, I had an interesting problem, similar to the screen issue, wonder it it might be related. I flashed to a new rom over the weekend, and no matter what I did, the backlight would turn off after 10 seconds. You could reset it to 30 in the power profile, but after a reboot, it would revert back to 10 seconds. Reflahsed it, and after the flash, when it starts loading the customizations, it would freeze. Flashed again, and it hung at customization again! Downloaded the rom again, deleted the old one, and flashed and it worked and the backlight would stay put!
Maybe the one you downloaded was corrupt?
Anyway, glad you got it working.
P.S. The rom isn't an "official" that I downloaded, it was one of the 6.5 that the cooks on the rom page whipped up. I think it was just a corrupted download.
This issue has happened to me a few times. even while i'm still using the phone and typing the screen goes off.
very annoying.
I found it only happened to me using EnergyROM. when I flashed to a different rom the problem was solved.
recently I flashed back to the newest version of EnergyROM again (after the previous ROM decided to hard reset all by itself) and this issue happened again in the first hour!
I really wish I could find a usable ROM for once and for all
My Case: WMWifiRouter was it!
This happend even when TP under Test rom env. I just gave up and installed latest version cause this ver is less stressfull.
Luckly 30 sec issue did not happend for a while until I installed WMWifiRouter.
Just after I install V1.50 30 sec thing and happend.
KB0907027: [BUG] v1.50 backlight timeout issue
http://support.wmwifirouter.com/knowledge/KB0907027/
I Installed V1.52 and now works fine and no backlight problem.
If you installed WMWifirouter check the link.
I use EnergyROM as well and i noticed that right after a fresh flash, if you tried to modify certain settings using the gui (i.e. alarm times, connection settings etc) they wouldnt stick - perhaps a direct registry edit using one of the tools previously mentioned might force the device to remember the changes? this worked for me when i had trouble with my alarm times not being saved.
ive also heard that sometimes a soft-reset isnt enough to commit changes to the registry - i.e. once making a reg edit, cold boot the device - that is press and hold the power button and turn it entirely off.
hope this helps

Categories

Resources