Database Info

Stuck in bootloader, please help!

Hello all,
Yesterday I tried to update my MDA Compact to qtek 1.06 and I saw to executables in the package:
getdevice.exe and enterbl.exe
I runned getdevice.exe for getting the device data for in the change.bat. That went oke, but out of curiosity I had to run the enterbl.exe, which made me go to the boot loader immediately. And now I'm stuck at the boot loader!
Whatever I do it won't boot to WME anymore! Soft reset, pressing the camera+power+reset, everytime it goes to the "Serial V1.00"screen.
When I remove and put back the backcover of the device (where the battery and sim are) it will go off and after a press on the power button it will boot to WME. But when I manually reset the device or when it automaticaaly reset itself after installing the ExROM tools, it goes back to the boot loader (Serial - V1.00) screen!
I even dumped the ROM with mmty to the SD card and flashed the device with that ROM again, but after it says Checksum is OK and I press reset it just goes straight to bootloader again.
I'm really out of clues of what to do. Can someone please help?
EDIT: When removing and putting back the backcover I can reset the device and it will boot back to WME so I can use it. But still when I softreset (with button or through software) it goes to boot loader. :-(
So using the backcover as a reset button is possible and does work, but it isn't very handy/usefull off course.
TIA
Regards,
Aurora13

Check the forum, the answer is there
Yes, you are still in bootloader mode and it's actually getting ready for you to flash.
Donno which part of it goes wrong, mine also have the same issue. What you need to do now is to restart your desktop pc / laptop (from the info I gathered from the forum). Then run that update thing again. This time, the same screen will appear saying it's trying to get the device data. Difference is, this time you no longer see the current version of ROM (as the Magician is in bootloader mode now). And you will see it show you the ROM that you going to upgrade to. Just follow the instruction, everything is straight forward. Hope this help.
cheers..

Thanks man!
You're the man cyberjaya!
It is working now, here is what I did (as told by cyberjaya):
- Rebooted my laptop
- Connected the MDA to the laptop
- Started the upgrade program of the qtek 1.06 ROM
- It didn't found my version, but it would let me update it to 1.06
- Flashing....(15 minutes is a LOOOONG time if you have to wait )
I did reset it a few times and it just boots normally!
Thank you ver much cyberjaya!
Regards,
Aurora13

No problemo
Am using laptop to flash also. Likely it's the USB hub thing (which listed in the "hardware devices" list). Read it somewhere, it's not recommended to flash using USB hub. Enjoy your new ROM!! .
cheers

I had a thought:
Isn't this the way to do a ROM upgrade without editing the ROM files?
Because it can't detect a different ROM and it will do the upgrade...
Or am I missing something?

need some help

hello,
I've tried to install skype ona my cingular 2125 and now it doesn't work.
the phone just stuck on .cab extractin screen and i restart it.now the only thing it show is the cingular startup screen and that's all.I have the cingular rom update uttility but it says that the device is not connected to the pc using usb,and ask me to check the connection.
what i can do about this issue?can anyone help me?
thank you in advance

Try turning off USB connection in activesync. With the phone turned off, if you hold the camera button when you plugin the usb to phone (already connected to PC), it should start up in the bootloader.
Other method to get the bootloader is to hold the camera and the comm manager button and turn on the phone.
You should be able to use the ROM update utility with the bootloader.
Look at Karhoe's guide in the stickies at the top of this forum...

Maybe hard reset will be enough ?
Turn off Your phone. Press and keep hold of both soft keys, press the power button for approximately 0.5 to 1 second, phone will ask U if U are sure, press 0.
hard reset is a lot safer than reflash...

i can't believe
thank you for all the advises but unfortunateli non of them helps.I've trie everything and it still shows cingular's wellcome screen and that is all.after that the only thing i can do is to remove the battery because nothing else work.I put the original rom from cingular and everything was OK with the setup, but after that -the same.I've tried with this hard reset- the same.probbably the nezt thing that i will do is to hit it into the ground )

mi4 said:
I put the original rom from cingular and everything was OK with the setup, but after that -the same.
Click to expand...
Click to collapse
Missunderstanding here
Our goal was making Your phone alife again.
None of mentionated procedures could help with some unknown to us bug in Your version of 3-rd party software

The latest skype works perfectly for me, in WM5 and WM6, since you are going to hard reset, why not perform a WM6 upgrade?

re
I was tried to reflash with the original aku2 rom from htc/cingular (the flash was successfull)but after that the phone is still not working.allways the same- cingular's startup screen and that's all.also try with hard reset with no success.I doubt that this phone will ever work again.or if there is another way to "clean" the whole memory?!is it possible to hardware reset the phone?

Format BINFS and reflash, that will clean everything except the IPL and SPL

Help with Error 260 on Wizard update

Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?

denflorida said:
Hi, help please...
I have Wizard G3 with TNT 5 Touch Flow and tried to update radio T-mobile UK 2.19 Radio Only. update went OK but now on loading I see HTC boot screen then it moves to TNT 5.0 screen and then fades in two minutes and starts back with HTC boot screen. It then circulates like that for ever without passing to the Today screen. On connection with PC for new update with any rom it shows: Error (260) update error. What can be done?
Click to expand...
Click to collapse
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
1. Disconnect your phone from the usb cable,shut down any firewall,disable any Anti virus,Reboot your PC.
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. On your PC Open windows Task Manager...>Tab Processes...>wescomm.exe...>End process
4. Power off the phone completely (Not stand-by,shut off completely),or you may take the battery out for few seconds
5. Make sure your phone is not Connected to the PC via USB cable and remove the dummy Sdcard or mini-Sd card
6. Get your phone into Bootloader mode (Multicolor screen) by pressing camera button + Power on button
7. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Be sure that your battery is charged over 70%)
8. "USB"will appear on the bottom of the screen of the Bootloader (Multicolor screen)
9. Run the Upgrade again and it will work fine without any problems.
10.Never use Bluetooth sync for the Upgrade
While upgrading, the ActiveSync program will not go on, however the upgrade is running.Please be patient when you're flashing your device, even if 98%. It can wait a little bit, 5 ~ 7 minutes.
Don't cancell the flash or get the phone off the usb cable till it confirms "Congratulations" or stops with an Error!!!
Hope it'll work, Good luck

Hi, this is the first time i saw a Paki guy on this web. I know there is alot of talent in IT profession in Pakistan. Anyway its good to see u here and i got a relief that with the help of a senior member like you i can get my phone work again.
To cut the chase, I have X01HT by Softbank Japan. It is Herms200 by HTC Japanese WM5 ROM. I have installed Asukal's English MUI and it was working fine for me. Now i'm planning to visit Pakistan this month so i though to unlock the sim and i used Prof v3a to unlock. I've successfully unlocked the sim and i guess CID also. When i use some other carrier's sim, i can receive the calls but cant make the calls out coz Softbank rom has a security which comes at screen and ask for password and dont let me do anything on the PDA. After studying alot on this forum i figured that i need to change the rom to get rid of that password message. i used the Olipro's Hard SPL and got bootloader 2.10 Olipro. I checked the other necessary stuff and when satisfied i started rom update. I end up with the same message of Error 260. Now my phone has no OS and it starts at bootloader. i tried everything possible like i make sure to remove all firewalls on my PC, used all the versions of Activesync and everything possible that i could. I trust that there is nothing wrong with the ROM etc but it is with connection.
Now if i update to the original ROM, i'm afraid that it will also upgrade my Bootloader and could never be able to flash english rom. I'm really depressed for the last three days and loosing sleep as well. I trust that you or any other senior member can help me with this.
Thanks in advance and looking forward anxiously.

Farrukh, wrong forum.
You know you have a Hermes, then you should know to post your questions in Hermes related forum, not wizard.
denflorida:
Try to update other Radio-only ROMs in xda's FTP server.

Sorry Brother, i know i have herms but i couldn't find some related topic in herms and i figured that Activesync problem is the same in all devices.
Anyway, thanks for the prompt reply. I'll try to find some from Herms.
Thanks

8125 rom update
i have tried to do a rom update on my 8125 g4. i recently purchased it off ebay and i have two problems. the reason i want to update it is because when i try to enable the wifi my device freezes. the other problem is that i can not seem to get the phone into boot loader mode. i have tried :
-turning the phone off and holding the camera button as i turn it on.
-holding the camera button and pluging it in to a usb port.
- using wizard service tool to enter boot loader mode.
after each of these different attempts i had to either remove the battery for 3 secs or hold the reset button for a few seconds before i can turn it back on. the phone still turns and just i can not use the wifi

Yes!!! Thank you! your instructions worked for me and got me past the Error [260] with my 8125 .

zabardast_1 said:
it's a case of bad flash,did anything during flash happened like lose usb connectivity,pc crashed,battery discharged or something like unusual ?
Try to soft reset and see if it works,otherwise you'll have to reflash to official carrier's rom in boodloader mode,
Click to expand...
Click to collapse
Thanks! Worked for Topaz and latest radio update.

Flashing CID Locked Kaiser

I have a problem with my device after installing Sprite Terminator, it has set a device password and i cannot figure out what it is.
Is it possible to re-flash the original rom to the phone, it is an OEM kaiser and has never been CID unlocked ?
I was wondering about flashing the stock rom via SD card or i can browse the contents of the phone and send files to it etc via activesync, i just can't run anything on the phone itself as stuck on the password screen.
I seem to be able to get to the bootloader screen and it says USB down the bottom
Hope someone can give me some advice
Thanks

Install HardSPL and you will be able to flash via SD card, or use CID unlocking program.
have you tried doing a hard reset?

The sprite software stops a hard reset so that isn't an option.
It's currently running the stock HTC rom as i have not flashed it at all,
Can i just do a simple reflash of the stock rom or do i need to go the HardSPL route. i was under the impression that i could just flash an original rom over the top as long as it's the same carrier etc without and cid unlock or hardspl, I cannot run anything directly on the phone as it's stuck at a password screen but activesync connects fine

boot it in a tri colour screen
hold two soft buttons(line next to green and red button) and stick in the stylus at the same time
release the stylus hold the buttons
when you see the confirmation screen release buttons and confirm the Hard reset.
that should work, I dont see how can a program disable a hard reset when the OS is not booted up.
good luck

spooki37 said:
The sprite software stops a hard reset so that isn't an option.
It's currently running the stock HTC rom as i have not flashed it at all,
Can i just do a simple reflash of the stock rom or do i need to go the HardSPL route. i was under the impression that i could just flash an original rom over the top as long as it's the same carrier etc without and cid unlock or hardspl, I cannot run anything directly on the phone as it's stuck at a password screen but activesync connects fine
Click to expand...
Click to collapse
or just reflash the same rom.....
just thought that Hard reset idea would be easier.
just out of curiosity try doing the Hard reset as I said, before you reload the Rom, I am also interested in that Sprite software and would love to know if it is Hard reset disabled

I can boot into the tri colour screen, i hold the two soft buttons down push the soft reset and the phone starts, Smart mobility, animated HTC Logo, Windows Mobile 6 splash creen then straight to the enter device password screen nothing else,
Sprite Terminator says it disables the hard reset option so i think reflashing is my only option.

are you holding two buttons while you sticking the stylus in?
you have to hold them and at the same time do the soft reset.....
I dont see how the software can alter the bootloader.... I could be missing something
alternatively just run the rom update for your CID and you should be fine

I was holding down the 2 soft buttons and the device just boots back to the device lock screen.
The software does stop a hard reset somehow and you can remotely lock your phone if it gets stolen by sending an SMS to it.
http://www.spritesoftware.com/store...MoreLink&utm_campaign=Terminator-HMP-MoreLink
I reflashed the phone with the stock rom and it is now working ok. many thanks for your help

no problems
good to now that it is working.....and that you sorted it out.

Kaiser stuck on green WM6.1 clear memory screen

I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?

bsgbelg said:
I have a Kaiser which I updated a while ago with WM6.1 official Belgian dutch. Since it became way to slow, I wanted to hard reset the device. Since a couple of hours, it has been stuck on the green WM screen saying The device is erasing the memory, Please wait...
I have been looking through the forum, but have not found the same issue.
It does not come up in acctive sync, so a normal relaod is not possible. Any ideas?
Click to expand...
Click to collapse
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!

Not possible to flash anything
what I've tried so far:
- activate active sync to install hardSPL. Not working
- install HardSPL through microSD. Not working
- install ROM through SD. Not working
I tried a non HCSD for a change, and then I see the loading scree flashing up, but quickly says No rom found and returns to the bootloader screen.
The only thing that works is load the bootloader (red green blue white) into a screen that says:
KAIS130
SPL-3.29.0000
CPLD-8
Serial
When connected to USB, it says USB, but no disk is showing in Explorer or any connection is made to AS
The only thing I've done in the past is flash the 6.1 rom through the system provided by HTC with a file called RUU_Kaiser_HTC_NLD_3.29.404.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
Please help, I really like this phone and hate to loose it

put it into bootloader, connect it to the computer and then flash one of the htc roms. make sure its an htc rom, you cant flash a custom rom cause you dont have hardspl

I have not been able to find the original rom, only the exe from htc which says Connect with active sync. Do I have to set it in bootloader and then execute the program?

Solved
Just want to let you know I sorted it out!
Flashing the original rom does not need active sync, the bootloader USB connection is sufficient.
After this, the phone restarted in 'Erasing memory' mode, but was able to finish it and reinstall the whole rom.
I believe I got the taste of it and will start testing some other roms...

msd24200 said:
manually go into bootloader if you want to reflash the rom, if phone is powered on hold camera button in and the softreset button at the same time! it sounds like you possibly have had a bad flash, OR you had a bad download!!!
Click to expand...
Click to collapse
Thanks, worked fine

majedaly said:
Thanks, worked fine
Click to expand...
Click to collapse
good to know