Related
It happened to me that the TC fell on the sidewalk face down, so I had to find and replace the screen. Couldn't find any pictorial guide so I decided to share my experience for the benefit of others with the same problem.
Cause: Cell phone shocked, fell down, hit
Symptoms: touch screen works OK, but display has cracks, blackened areas, which are spreading as time goes by.
Screen type : TC combines the matrix sensor (touch) and the LCD in 2 layers, the front touch-glass and shell, and the LCD itself underneath it.
Source of display: I bought via eBay on this source: Asia Bol
http://stores.ebay.com/newasiabol
Cost $70 inc. shipping and arrived within a week and a half. Rumors insists the at below $100 a screen is either factory dropout or refurbished.
Tools needed: Torx screwdriver T5-50, the size can be viewed after removing battery door, at lower corner.
A flat sharp tool ("fish knife") to help open the plastic case, but not too sharp to scratch the phone.
Here are the pictures and some notes:
1. Remove battery case and battery, SIM
2. Remove 2 screws from lower side
3. Prick open the shell with the flat tool
4. Prick open the top shell with the flat tool
5. CAREFUL as there are 2 tiny ribbons from the touch screen/hardware buttons into the PCB, one is held in place with sticky band (keys), the other (digitizer) is locked in-place with a lever, tiny one! - pull them out, not before noticing where they went into and lifting the lever on the smaller one.
6. Take apart the FRONT shell with the flat tool slowly as not to tear ribbons
7. Pull the LCD ribbon out
8. Carefully pull the old screen as it is held in place with sticky gum
9. Clean interior glass of phone if needed, pull out new screen protective sheet and put in place.
10. Connect new screen ribbon, 2 keyboard/jog tiny ribbons
11. Press shells in place
12. Pray you didn't forget anything and load SIM and battery
13. Good luck
more pictures...
following...(please note that where it's marked on the above picture as "jog wheel" - it is not. it's the glass digitizer ribbon.
Excelent work....!!!
Awesome man
Great contribution! You give me hope for the next generation of xda'ers!
Thank you!
Excellent work! Must be added to Polaris wiki page (if it hasn't yet!)
my lcd screen crashed 1 month ago. replaced a new screen for 450 CNY included the handwork fee.
great job.... thanks for sharing
My TC has got a big scratch on the screen (cheers to Jack, my cat who is responsible for that )...
I just ordered a new LCD screen, and by "mistake" i only ordered the digitizer...
Now after reading this post, it seems that I accidentaly did the right thing, since is only the front panel which is scratched and not the LCD itself... Am I correct?
Anyway do i have to disassemble the whole phone to get the front panel out???
As you see on the completly dismanteled TC picture above (left on the last picts row), there are:
Glass top, actually the outer top shell, and the LCD & Digitizer are one piece (the 'glassy' square with flat orange attachement)
If the scratch in on the shell glass, that's not the LCD screen, it is the so called "LCD LENS GLASS" or "faceplate".
If the TC fell and you see cracks and smears on the screen instead of what should be displayed, that's the LCD.
Please make sure where your scratches are.
Reuvenm said:
As you see on the completly dismanteled TC picture above (left on the last picts row), there are:
Glass top, actually the outer top shell, and the LCD & Digitizer are one piece (the 'glassy' square with flat orange attachement)
If the scratch in on the shell glass, that's not the LCD screen, it is the so called "LCD LENS GLASS" or "faceplate".
If the TC fell and you see cracks and smears on the screen instead of what should be displayed, that's the LCD.
Please make sure where your scratches are.
Click to expand...
Click to collapse
Thanks for the Info,you ve been very helpful .... Well my scratch is on the outside and I couldnt find any outside faceplate for my TC... Instead I ordered the digitizer (see picture attached) which for me it seemed as the right option (I did that before reading your post )... Now I will just have to wait and see when it comes, if i did the right thing........ I will let you know
well, I was (and still) confused as I was looking for some info about the screen assembly, and the only one I've found was on this lab site (not particular to TC model though).
Please read the paragraph in RED starting with "ATTENTION..." later on that page (the link above includes Google's translation from russian).
More confusing is that the part you mention here IS available as is...
puzzle solved.
I was curious so I dismantled the TC again, than I notice the the glass shell IS carrying a tiny ribbon, which means IT IS the digitizer (I though it's coming from the hardware keys).
So I assume you ordered the right part.
Reuvenm said:
puzzle solved.
I was curious so I dismantled the TC again, than I notice the the glass shell IS carrying a tiny ribbon, which means IT IS the digitizer (I though it's coming from the hardware keys).
So I assume you ordered the right part.
Click to expand...
Click to collapse
cheers... I feel ever so glad!!! ... but you would recon I would have to go through all the procedure to get it out and install the new one?
Actually it's a very delicate work with a steady hand and non scratching behaviour.
points to notice:
- The side silver bars are detached by sliding as well as pulling gently, as there are L shaped pins coming out of them into a niche in the body.
- The glass digitizer ribbon is run from one side of the main board into the other, so unlocking it (small lever and pull out) is needed as well as having the upper and rear shell apart as much as allowed, Or having the LCD wide ribbon out (& digitizer small one) and let the 2 shells free for easy access.
Saying that, it means that the procedure is almost identical as for replacing the LCD as the glass/digitizer is attached to front glass with sticky rubber and you need to get in there to release the tiny ribbon.
In your case I assume you also have to pull the bottom hardware keys' plate (assembly), in order to release it from the old shell/glass.
If that is the case, be carefull as the assembly is pinched into place by fragile plastic bumps that keep it in tight place in order to make a good push action (click). You'll have to widen the shell sides a bit and help it out.
! bent ribbon, and some mulfunction may occure.
Awesome Guide, Reuvenm you're the MAN!
I'd been searching all over for this guide so as to attempt to remove both the front and back camera. My Company just implemented this silly policy that doesn't allow phone w camera
Reuvenm, by any chance that you've had a good look at both the front and back camera and if it's a type which can be un-plug easily? Pls do not bother to disassemble the TC again, really. Just wanna check cos you may have shot some other pics of your disassembled gem that may show the front and back cameras
Anyway, great job and thanks a bunch in advance
you can disable the camera by software & registry, but I guess they want it to be out of sight..
as you see on the left pict on the first row of images, the front camera is a cubic aparatuse with 3-wings circle in the middle, just underneath the ext GPS antena hole:
this can be pulled out but I think it's ribbon (connection flat wires) is going via a cooling metal plate element and then to a PCB connector. Not sure about that as it's very delicate in there.
as for the back camera, I can't recall
here is a close up:
Hi Reuvenm, thanks for the really quick reply. Yeah i wanna get them removed altogether. So I took a leap of faith and viola! I had gotten the Back camera (3M pixel cam) out!
Followed the steps as you had illustrated and yes the 3M pixel camera was attached using some kind of L-shape flat metallic ribbon cable that ends up w a PCB connector. Wasn't difficult to remove though. I'll try to disassemble the Front camera tomorrow when i've got the time cos got to catch up on some work now.
A really big THANK YOU to Reuvenm for posting this amazing guide and i'll get some shots of the Front Cam removal and post them back here again.
Outstanding work man
You really got the guts gotta say
Elegantly done and explained!! I copied this guide with pics for future reference
This opens the door for a whole new era I guess, right guys!?
glass deformation
Hello gusy
Can you give me a suggestion ?
One day i noticed this "stain" on my screen when the device is off.
At first i thought it was liquid traped insinde the lcd (as seen on other phones) but it turned out not to be.
This stain is visible only in bright neon light (at my workplace), and it moves or dissapears almost completly when i press the screen.
Outside, or in normal light the sceen has no problem.
I think that the top glass part of the screen is to big and it bends a little causing this.
Can i remove the top layer of glass, cutt let's say a half of milimiter from the side, and stick it back on ? or is there someting holding it under ?
I noticed that in a corner i could peal it off, but i don;t want to take any chances to breack something.
thanks in advance
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Protection
Personally i prefer to have a screenprotecter on my device. I can recommend invisible shield. its very durable and will not be scratched. check it out on www.zagg.com
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
willyy1991 said:
Ok, i've had a problem with it, first i removed the protector that was as large as the device and made the screen very ugly, then i got the one from the box and putted it on, every air-bulb was gone when i kept rubbing etc.
1 stayed, under that bulb there was something white, i found out it was a 'piece' of dust.
It was kind of annoying so i removed the screen-protector, now when im trying to put it on i get lots of 'dust-bubbles',
Anyone has an idea of how to do it or should i just leave my diamond without the screen protector?
Click to expand...
Click to collapse
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
mhfalken said:
If you remove the protector, then there will alway be dust next time, because the dust get stuck to the protector glue. (I have also remove mine several times)
I have tried zagg, but I can't recommend it. It is a little sticky (which they also says on their homepage) and I don't like that. The floating feeling is gone. It is also not that invisible.
I have selected to buy a new original protector, and will use that.
The trick to get it on without bobbles is to start on the long edge and then slowly add it. (Keep the 'paper' on as long a possible).
(Michael
Click to expand...
Click to collapse
Where can you buy a new one, i need it really fast because my phone is without protection right now and no i am affraid of pressing it to hard to leave a permanent mark..
tnyynt said:
The original is washable. Wash it and dry it with a paper towel that sucks in the water bubbles, wipe dry and clean your screen and reapply it.
By the way, this goes to Accessories forum.
Click to expand...
Click to collapse
I did this and the dust keeps coming at the protector and my phone and there will be bubles because the dust gives it a 'height-problem'..
I bought invisible shield for mine, its pretty nice after say 4 days from install.
For first 2 days it might seem really bad but it gets much better.
I somehow scratched it without even noticing it, so I sent picture to zagg and they sent me new one. Even though scratch was very minor.
mhf
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Perhaps you could use isopropyl alcohol, usually it will remove glue without damaging the plastics surface (in that case: your display). DON'T USE nail polish remover, acetone or even benzine, it will remove the glue too - but your display would look "milky". You can get isopropyl alcohol at the pharmacy.
Tell us if that helped you
mhf said:
hi. this my first post on this web site
excuse me for my bad english
i have a diamond and i remove orginal screen protecter because i write sms with letter recorgnizer and the area that i write words on the screen become white and scratch. i remove orginal and buy a new one that for iphone. i cut it for my phone size and apply it. its sooo much stiky and i have a problem like orginal one.i wnat to remove it and when i do it a tiny layer of glue stand on my diamond screen. i can't clean it. and it give a bad scene to my diamond.
what's your idea. i give u a pichture from my diamond screen.
Click to expand...
Click to collapse
You might be interested in this thread: http://forum.xda-developers.com/showthread.php?t=421229
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
the exim screen protector is very good and smooth
I always use the Brando screenprotectors. See their online shop. They ship worldwide for only $ 3,00 shippingcosts.
It is very easy to install, easy to clean, 100% garanteed scratch free and very durable.
iixnullxii said:
I didn't get a screen protector with mine... I mean, I had a shipment protector with a little tab for peeling off, but nothing came with it for long term use. It's a Sprint, did they just not include one?
Click to expand...
Click to collapse
I've got a Sprint Diamond too, and didn't think I got a protector either, but it was in the separate bag that has the manuals. It should have come with one...Wish it woulda come with an extra one too, oh well.
I had the same problem with misalignment and dust bubbles with the HTC protector on my first few tries...i did however fix the problem...
Take the protector off and clean off the phone...use a microfiber cloth to get all the dust and oil off...after its super clean...take the protector and wash it off with some mild soap...rub the soap in with your fingers and get it clean. Be sure to note which side is down. After its clean, hold it around the edges and let the water bead off...i blew on the protector to get residual water off...some water is ok...actually helps with the install...the basically carefully apply it still holding the sides making sure not to leave finger prints. Start from the top and work your way down... i used a credit card pushed against the microfiber cloth to squeegie the protector down...be carefull with the few drops of water. After you have it down...there might be little bubbles or what looks like water spots where water is trapped under the screen...dont worry...just use your phone and leave it alone. Once it heats up from the excessive phone use it will start to dry up and the protector will come out very nice and smooth. Mine is flawless and i did the wash with soap apply and remove at least 3 or 4 times to get it right...Just be patient
I use screen protector from martinfields, what do you say about, anyone have one??
I think the best in market
My HTC one got a nasty scratch in it last week, so I ordered a Martin Fields.
It arrived this morning and I've got it on without any problems. So far I've noticed:
- It's not a perfect fit like the HTC one was. The hole for the speaker at the top is larger than the hole in the phone. It's not bad though.
- The visibility of the screen does seem better than the HTC protector, but I don't know if it's just the placebo effect of having a more expensive protector.
- It was _easy_ to put on, no bubbles at all
- The protector for the bottom buttons is awful. The circle is just the right size to completely hinder using the touch wheel and it's obvious that you've got a piece of plastic on there.
- It seems smoother than the original HTC one when using the stylus.
So far I'm impressed with it. I didn't bother with the camera hole or bottom hard buttons. The in box HTC one was fine for me, but when I got a scratch on it (my stylus somehow developed a sharp edge), it annoyed me.
I'm using the one supplied as standard with a uk CompactIV and it's great- you can hardly tell it's thereand the sensitivity seems fine.
I have 24 diamond screen protectors. Because i bought 24 diamonds and sold them all without screen protectors so i am sorted untill i buy another phone.
After using the martin fields one for a couple of days, I think it's great.
The screen looks much brighter and clearer through it (I thought the HTC one was great, but I do notice the difference). Plus the smoothness is brilliant, theres pretty much no friction for the stylus or fingers
where can i purchase the htc screen protector? the original that comes in the box...
I was peeling off my bodyguardz screen protector to put on a new one, and the darn thing was so stuck to my screen it took a lot of force to peel it off. As I was pulling it away I noticed that my "screen" seemed to be lifted off my HTC fuze!! After I kept pealing I noticed from the side that there was a film that was peeling off that had adhesive to the screen with the body guardz. I'm too scared to proceed and have left my phone that way.. my question is there a protective film (not counting any sort of screen protector even the one that comes with the fuze) on top of the screen, and that was what was peeling off? Is that film important for the touch screen itself aside from protecting it (or does it keep some part of the screen in place etc etc).
Thanks in advance, the screen does turn on and is still touch sensitive but I'm too scared to peel off the rest of the body guardz that have that "film" come off with it.
Someone removed that and lost their touchscreen so be scared IMHO.
aaahhhhh can you link me to that post? I tried doing a search, I cant separate that film from the bodyguardz either... =(
I think it is the digitizer that is comming off, or part of it anyways... the only thing I could find online is this
http://forum.xda-developers.com/showthread.php?t=392301&page=3
Post#27
"--------------------------------------------------------------------------------
Hello again
So
After giving it a lot of thought, i decided to disasamble my phone to see if i can get rid of that stain. I have to say that it was a bit difficult to folow the guide but i finaly opened my cruise.
In the end i realised where was my problem.
The digitizer has 2 components:
A glass layer witch is on the bottom, and a plastic one (on top) witch are keppt together by twosided adhesive tape.
The "stain" was caused by the plastic layer, witch for some reason wasn't staying straight (it had a small bump...).
I figured this out when i pealed this layer from the glass one, witch i shouldn't have done because the layer has a connection with the glass and the small ribbon witch goes into the mb.
So for any of you, if you encounter my problem, better let it that way, cause the alternative will be a new digitizer.
I'll go to the htc service in romania to see how much will they charge me for a new one, and if the amount is to much, i'll try to order one from the web(altho not that many companies ship to my country )
Wish me luck.
LE: I have a question thow
How can you remove the digitizer from the casing ?
I tryed to pull it but i was afraid to damage something (else).
--------------------------------------------------------------"
http://forum.xda-developers.com/attachment.php?attachmentid=100767&d=1216648485
Heres a link to the picture the guy with the polaris took... the HTC black bordered part is still on the screen but there is a film sitting on top of it thats peeling off with the bodyguardz.
This is a cruise polaris and not a raphael but I think this post is referencing the same thing. Does anyone have any advice to give me? My phone is still sitting there with half of the "digitizer" peeled off stuck to the bodyguardz grrrrrrr
bump...........
tassadar898 said:
I was peeling off my bodyguardz screen protector to put on a new one, and the darn thing was so stuck to my screen it took a lot of force to peel it off. As I was pulling it away I noticed that my "screen" seemed to be lifted off my HTC fuze!! After I kept pealing I noticed from the side that there was a film that was peeling off that had adhesive to the screen with the body guardz. I'm too scared to proceed and have left my phone that way.. my question is there a protective film (not counting any sort of screen protector even the one that comes with the fuze) on top of the screen, and that was what was peeling off? Is that film important for the touch screen itself aside from protecting it (or does it keep some part of the screen in place etc etc).
Thanks in advance, the screen does turn on and is still touch sensitive but I'm too scared to peel off the rest of the body guardz that have that "film" come off with it.
Click to expand...
Click to collapse
That has happened to me as well. I'm afraid you'll just have to get another digitizer off ebay.
ughhh!! any help on the assembly?
Spray some of the liquid that came with it on the touchscreen (underneath the bodyguardz screen protector; spray little by little or use your finger) and it should come off with a little less effort without tearing out the screen. That's what I did. Btw, make sure you turn off your phone and dry it before you turn it back on if you do that
Alright, I did send sms on my bicycle which resulted in I did drop the phone on the ground. Luckily I had ad NILLKIN glass screen protector, which did save most of the phone . I have ordered a new Nillkin screen protector from Aliexpress. And I hope to patch up this phone so it looks good again. How would you have done ?
As you can see at the bottom in the pictures there is physically damage, you can you see the screen bleeding thru also the huwawei logo is damaged.
My idea is UNDER the NEW Nillkin screen protector I will try to mask these "holes" so the screen is not beelding thru anymore. What material should I use to patch up these holes.. also.. how to repar the logo ? can I print it out on my computer printer ? it might look **** on paper but UNDER the glass protector it might look a lot better.
All creative ideas are appreciated, I have high hopes the phone will look good again..
And hopefully my phone will surrive until the M8 release.
Just to let you know desipite the glass look damaged like this the phone is still fully functional!!
ouch i can feel with you.
How about some black film, black paper or everything else that is black and thin
Yes some black material for sure.. Black film would be perfect in guess.. Just wonder where to get it also some black glue at the sides also..
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
alexre123 said:
Maybe you can find a front replacement? - http://www.ebay.com/itm/New-Front-O...-Parts-For-Huawei-Ascend-Mate-7-/201270995814
http://www.ebay.com/itm/Original-Re...s-Lens-For-Huawei-Ascend-Mate-7-/141549809429
Don't put a huawei printed logo there lol it will look bad and cheap.
Click to expand...
Click to collapse
Nice man might be a very good alternative! But how easy is it to change it really?
Do I need a heat gun for that?
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Or...if you have the courage go for it ) - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Joke man, don't do it yourself if you don't have experience
alexre123 said:
Don't know. I don't advise to do it yourself , just go with the phone to any service, I'm sure they know how to do the operation. Or maybe you have an huawei service near you.
Click to expand...
Click to collapse
I have done some smartphone repair myself, I changed the USB board on my old Galaxy Note 1.
I bought a smartphone repair kit with a few tools and very small screwdrivers. To change the glass is probably not much harder, but I need to know if I need a heat gun since I do not own any yet Hopefully it is not needed..but I would assume so...
I might also add the reason I bought a screen protector was that the original glass underneeth have a small crack too that goes accross the entire screen but it s quite invisible besides from certain angels.. so to change that screen to would actually be amazing..and it would make the secondary value when I sell this when M8 is released be a lot higher..
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
alexre123 said:
I think you need one. Look at the second yt movie at 22:34. Have an hair dryer?
https://meta.ifixit.com/Answers/View/3523/Using+a+hairdryer+instead+of+a+heat+gun
Hair Dryer vs Heat Gun
https://www.youtube.com/watch?v=9ELHDYjpLoc
If I was me I would go with the phone to a service. Anyway good to know Nilkin tempered glass do the job, I have one also on my screen
Click to expand...
Click to collapse
Yes the Nillkin glass did its job but I think I was unlucky, that the bottom of the phone got under my bicycle tire.. it felt like it...
I recommend Nillkin, IT has very good Oleophobic coating, which makes the whole device a lot more enjoyable to use, but be careful whren you put it on non 100% straight surfaces it will slip onto the floor.
Alright it is more or less decided I will buy a new front cover with glass, I will make sure to get original parts with gorilla glass. Since the ebay link you linked to are chipped from china I guess I can just order straight from alixpress instead...
I have heard singapore post have quite fast shipping compared to china post.
just one question is hard to see in the videos.. but do I really need to disassembly every component all the circuits boards just to change the front screen ? do I need to open the case at all when using the heat gun/hair dryer ?
If as in the every component and circuit board has to be disassembled it is over my competence probably... unless I am super careful..
Mutch better if you want to purchase an original front to replace it. Don,t know if you really need to take all the components of for replacing the front screen, but you can make some research on it or you can ask on other forums, maybe are others with more experience.
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
blackinfinity said:
yes I understand..must decide tomorrow then.. because of shipping times a fast decision need to be made otherwise I will have to wait too long..
Click to expand...
Click to collapse
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
ehhm... good luck OP
XDADEVX said:
Man I was repairing the whole Mate7 from the scratch!
If u shattered the screen ;
1.You will need new one which cost £40-£60 2.You will have to strip the WHOLE phone which is pain!
3.You will have to open the back cover,which is very hard process.You will need hard force to pop back cover from hinges.(first you need to remove small bottom cover which is plastic.)You will have to pry it underneath is adhesive which holds that small cover firmly.
4.Once you manage to remove back cover you have to disconnect all flex cables.There are 3 black screws and 4 chrome screws(smae like two at bottom) which holds motherboard.
There is small black cover which covers all connectors and it is tricky to remove it,because left side is kind of locked under chrome metalic cover plate! You need to pry it slightly to the right to flip it upwards.Be careful! One black screw holds that small black plate!
Once you remove the motherboard, another and very very hard part awaits you!
5.Removing the battery!
You will need heat gun to remove battery but even that heat gun might ot help you to remove BIG battery without damage !!
I tried to remove battery without damage but no luck.So I will advise you to buy new battery for mate7 mine cost me just £8 from china but I had to wait almost a month to deliver! Disaster shipping from china!
So if you apply lot of heat you might be lucky remove battery without damage.
But I was scared to apply too much heat on battery it could result in explosion or fire!!!
So I rather purchased one.
Once you remove battery, you can remove bottom part of phone which is usb board with speaker and plastics. It is up to you you dont need to remove it.
6.Removing the damaged screen from (middle) supporting frame!
This can be easy depends how screen is damaged. BUT
Here you have 2 options to replace screen.
A:You can buy screen without supporting frame which is harder and more work and heat gunning around the screen and prying screen from middle frame.Needs like 30-40 seconds of heating around the screen not in the middle.
B:You can buy s reen with middle frame which is very easy.Screen is already fited in frame so you dont need to mess with very slim adhesive srtips around the screen(which I done)
Then you will have to remove all parts from middle frame. Ear speaker ,loud speaker usb board and replace it to new housing.
Once you will set the new screen you can put all parts back together..
Replacing screen for this phone is PAIN!
It really needs skills and be careful because it is very easy to scratch back cover.
Click to expand...
Click to collapse
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
blackinfinity said:
Hello and thanks, I appreciate your detailed instructions.
But I need to say one really IMPORTANT THING
IT IS NOT THE SCREEN THAT I NEED TO CHANGE THE ACTUAL SCREEN AND LCD IS WORKING PERFECTLEY WHAT I NEED TO CHANGE IS THE Front Screen Outer Glass Lens. i HAVE HIGH HOPES THAT IF I ONLY CHANGE THIS I DO NOT NEED TO DO ALL THE INSTRUCTIONS YOU DO SINCE I AM ONLY CHANGING THE GLASS NOT THE ACTUAL SCREEN, IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT. I HOPE YOU WILL READ MY POST AND GIVE ME AN UPDATE BEFORE I PUSH THE BUY BUTTON THANKS!
This is the part I was going to order it is just the glass no lcd screen.
Click to expand...
Click to collapse
Sorry but you are like 10 year old child..
So u wanna change your ''front Screen Outer Glass Lens'' ??? (that is damn long name for glass )
You have so much hopes ? OK .. go on .. I leave you to it ..
I wish you very best of luck ..
''''IT IS A VERY IMPORTANT DIFFERENCE BETWEEN SCREEN AND OUTER GLASS AND FRONT''
DDDDDD this was so funny :laugh: :good:
Fingers :fingers-crossed:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
blackinfinity said:
You was talking about changing the lcd not only the front Glass. I just wanted to make sure you need to do all the instructions to change only front glass. The lcd is working..
Click to expand...
Click to collapse
And I will give you one last advice ; that my detailed post above I explained you how difficult it is .. YOU want to change glass only ??
And what you think, you can just do it without stripping phone apart ?? Are you magician ? You would have to open phone anyway !
And replacing glass on your screen, do you have any idea how you gonna do it? Removing glass from LCD is x10 TIMES hard that my instructions above man !
So you basically adding even more, harder work to hard work ..!
Do you even have
1.LCD separator heat machine ??
2.Cutting line wire ??
3.Cleaning alcohol chemicals ??
4.Optical clear adhesive glue ??
5.Ultraviolet curing lamp ??
Come oon man ...
I told you I wish you very best of luck..
This guy want to do the exact same thing - https://www.youtube.com/watch?v=O8HNBtl9MwI
You have the all process here - https://www.youtube.com/watch?v=nDiaQOzCvfE & https://www.youtube.com/watch?v=lUl8dCuhBGw
Take a look and decide if you want do it yourself and risk to mess things up or go with the phone and the replacing part to a service and let someone who did this before.
Hi!
A few days ago I dropped my phone and until it hit the ground, I accidently kicked him with my leg and it got knocked by the wall and finally touched the floor. When I lifted it up from the ground I noticed what you see in the picture. It look's like an air bubble between the screen and the screen protector. But this bubble is underneath the first layer of the screen. Until today the "bubble" hasn't expanded, and I hope it wouldn't go further. My phone has still got the warranty paper available, idk if I'm going to send my device to their service and they will repair it...or I can go to a random service to check it out and maybe they will be able to repair it, or do worse...
What is this "bubble" afterall?
Screen is made of multiple layers, the digitizer (for touch) is the top layer iirc, the screen LCD is underneath, usually glued together, looks like the two have separated
*Detection* said:
Screen is made of multiple layers, the digitizer (for touch) is the top layer iirc, the screen LCD is underneath, usually glued together, looks like the two have separated
Click to expand...
Click to collapse
Any chance to repair it without great costs?
Smantanasiceapa said:
Any chance to repair it without great costs?
Click to expand...
Click to collapse
Without replacing the screen, not sure, I know you have to use a heat gun to melt the glue between the screens to replace just the top glass layer, so it's possible if it has just come unstuck that could melt it back down, but might make it worse