Hiya. Im new to this place.
I was given a broken SPV M1000 A while back. It just needed a bit of TLC. The device works 100% fine now after being taken apart and thourghly cleaned of goo and stuff. It obviosly had an abused life, as it seems to have been "RIPPED" from the cradle and damaged the port on the bottom.
I have resoldered it once and it was fine for a few months, but has degraded due to the connector being damaged. The socket is now beyond resoldering as the pins have been bent. Could someone tell me where to source another connector?
I sync using bluetooth and have two batteries and charge one while using another.
Is it possible to install WM5 on this device? I assume i need to get the connector on the bottom going again.
Thanks for any help.
Dave.
Related
My Xda/Qtek's charging slot is loose or bent and as such I am now not able to charge it or synchronise at all. Brought to the repair shop and was told that I need to change the whole mother board as the slot is attached
to the board and it is as good as getting another one than to fix it. Seems to me that the 2 pins in the centre or the slot is bent and I cannot get the connection on when I plug the charger in unless I twist the charger to one side I then get the yellow/orange light which indicate charging.
Appreciate if someone could help fix it. Cheers.
The charging socket is part of the mainboard, I have had this in the past with ipaqs, I got a jewellers eyepiece and a very slim pin and managed to get them lined up again, I am sure there was a post today about this very problem.
Thanks for info. I managed to strip apaart the xda and then soldered the
loose charging slot. It works fine now and I save having to pay for the replacement of the main board which is not worth it and also the service
costs.
help for newbie pls?
Hi, I currently have the same problem. I also want to try the solution that cruisin-thu suggested, unfortunately, I'm not much of a techie and I'm afraid that I might damage the mainboard if I don't know which parts to move. Does anyone know of any sites that have a picture of the xda II mainboard? I'd really appreciate the help.
Any hadware pro`s out there?
Somehow I have managed to damage the contact strip on the bottom of the phone. It will not charge in the cradle, but the battery charges in the cradle. Sync using the cradle is OK. I think it needs a new connector strip. Does anyone know if this is a "beyond economical repair" type of problem, or have any ideas how to approach this. I could take it to an O2 shop for a quote, but that may take weeks, and besides its an unlocked phone, and they might not be 2 impressed!!!
Thanks,
Justin
I had the same problem. Sent it to the XDA service centre
they said it wasn't covered by the waranty
Cost about £70 to get it repaired
tel 0808 100 3427
Thanks
just found out £104
I also have the same problem mate. Not quite sure how I bent it though.
I managed a small repair, but I still have to angle the charger slightly to get it on. Everything still works for at the moment, so I don't think that I will get it repaired.
Nearly forgot, this is my first post so hello to everyone!
i had the same problem
they have send it away (where i bought it (camera/phone shop) ) and i got a new motherboard
fixed now
for anyone searching the forums
http://forum.xda-developers.com/viewtopic.php?p=146805&highlight=#146805
I have replaced my Connector with a usb socket
wow!
This is really amazing! Planning to 2 it with mi BA.
Hope it works... :roll:
now if only one of those bad boys carried an audio signal we'd be in business for a nice car docking station!
Hi
I have major problem with my tablet and usb socket has been pried from board have taken a quick look at damage and a replacement or solder of new one is out of question and metal contacts on pcb has been damaged also.
I am wondering if anyone knows a way of bypassing so I can still charge.
Can I bypass the small circuit board where USB connector is and hard wire battery connections directly onto USB itself.
This tablet has always served me so well dont want to give up on it just yet as cant afford a new one.
Fairly confident with soldering etc just curious as to whether it will work and best way to wire it up
My HTC Sensation, has stopped charging altogether. I took it off charging and when i put it on 10 min later, the LED didnt light up, so i got a toothpick and tried cleaning thecharging port just in case something tiny went in and was blocking it to charge, but that didnt work. The phone was working fine until the battery died and i still cant get it to charge. Now im wondering whats broken, to all those repair specialists out there, what could be broken? I can buy a charging port from ebay, but is that it? or could it be anything else.
I was looking to upgrade soon but was waiting for some christmas deals to pop up, but my phone decided to let me down.
Any help appreciated, thanks guys
webstar1 said:
My HTC Sensation, has stopped charging altogether. I took it off charging and when i put it on 10 min later, the LED didnt light up, so i got a toothpick and tried cleaning thecharging port just in case something tiny went in and was blocking it to charge, but that didnt work. The phone was working fine until the battery died and i still cant get it to charge. Now im wondering whats broken, to all those repair specialists out there, what could be broken? I can buy a charging port from ebay, but is that it? or could it be anything else.
I was looking to upgrade soon but was waiting for some christmas deals to pop up, but my phone decided to let me down.
Any help appreciated, thanks guys
Click to expand...
Click to collapse
Did you solved the problem by buying a new phone?, the problem could be the USB connector himself, if you are very handy you can repair it yourself...
anomalic said:
Did you solved the problem by buying a new phone?, the problem could be the USB connector himself, if you are very handy you can repair it yourself...
Click to expand...
Click to collapse
maybe your battery died
I'm assuming you've got it fixed / moved on to a different phone / are using an external charger, but this thread got bumped to the top so I figured I'd chime in.
I had this problem as well. Unfortunately, the usb port is soldered on the board and not a separate unit attached via ribbon cable. The solder joint holding the port on the pcb cracked, resulting in a loose port. Over time, this lead to the pins breaking off the pcb. For a while, I was able to get it to charge by applying pressure to the usb plug. Finally, I took it apart and resoldered it, reinforcing the solder joints for the port itself. It's not too difficult if you use some flux. Just line up the pins and tack the port back on. Then rub flux over the pins and tack them with the soldering iron. No additional solder is needed or recommended-- the pins are in close proximity and it'd be easy to bridge them.
Hi all,
It's been two years I have been using my Z5 Compact, and the MicroUSB connector is hardly usable now.
I of course tried several cables.
It is very difficult to charge the telephone. I don't know exactly what the problem is. I tried cleaning with a dry air bomb (for keyboards etc.), but to no avail. Seems like a bad contact.
Is it possible to use electrical parts liquid cleaner to properly clean the USB contacts?
Anybody having the same experience?
MF
I had the same problem, usb cable didn't fit in entirely.
Culprit was a piece from the inside of my jeans pocket was pushed deep inside my usb port. It was pretty much stuck in there but once I got it out the problems where solved and I switched to magnetic usb cable to prevent this.
I got it out using very tiny pliers and a magnifying loupe.
Hope this helps..
Regards
Mine is going to die sometime, soon, too! i already bought a new one on ebay, laying ready to be installed here! In a couple of days i´ll take a hair dryer and then i´ll peel of the back cover and replace that broken connector
update: 17th of june!
Just wanted to tell you guys, it worked! I just replaced the USB Connector with the one i bought on Ebay, price was around 4 Euro or so, not much i think
It was rather easy, as i already own the needed tools (a very very small philips screw driver, and a tool to go underneath the back cover and a hairdryer)
took about 20 minutes or less!
Just use the hairddryer to heat up the back cover, then use the special tool (or a thin knife?) to loose the back cover and peel it off
then you have to remove 2 screws on the lower part, then you can remove some sort of a "bar" over the usb connector! next you have to lift the "motherboard" on the lower part (yes it moves down to the usb connector) but first disconnect the usb connector! then pull out the broken usb, shove the new one in and do all the above in reverse order!