Database Info

dead or alive

My jam is stuck on the serial screen
tried upgrading with imate original, wont see the phone
tried mtty d2s (from a working unit)>NTRW READ FROM sd, ntrw WRITE TO SD, it freezes on boot,
the mtty intracts with the phone: here :
USB>info 0
MAGICIAN
USB>info 1
1.00
USB>rtask 0
Radio reset.
USB>checksum
CRC checksum=0xACC883CE
no luck restoring the backup file,
any clues ?
thanks.

ok seems i have a shot bootloader, when i try d2s, the screen goes blank.
s2d dows not work with jam
rbmc is locked!
erase is locked
password >> need a password to do much of the writing commands
lnb >>not allow operation
in short, there is no way(from where i stand) to flash this thing, attempting to flash with SD returns a frozen set, same SD was able to flash another unit.
any clues ?????

I now have the same prob...
I wanted to flash the: ma_cdlsku12_wwe_10300_163_10100_ship.exe
but it now is stuck in serial mode...

pc->drive.total_lba=77380
pc->drive.num_heads=8
pc->drive.sec_p_track=20
pc->drive.num_cylinders=773
pc->drive.block_size=200
pc->drive.features=0
pc->drive.RCA=A95C
pc->drive.drv_type=0
pc->drive.securedAreaSize=1500
pc->drive.securityDrv=5
pc->drive.busWidth=1
pc->drive.erasedSize=0
Total card size=EE70000
SDCARDD2S+,cStoragePlatformType=FF

My probs started after flashing the UK ROM of the I-mate in to my MDA Compact.
MTTY:
USB>info 0
MAGICIAN
USB>info 1
1.00
USB>rtask 0
Radio reset.
USB>checksum
CRC checksum=0x68A159CD
I can't flash my MDA compact Backup ...
What could be the sollution?!!

can you do d2s from mtty ? if so, you are in luck, you can still revive your set. if not, try the warranty option something i do not have.
Try d2s, if it works, stop, download the backup from the xda ftp, use ntrw to write it to SD, then put your set in boatloader mode with the SD in, wait 7~10 seconds, it will ask you to press power to flash, & you are there.
if you cannot perform a d2s, your screen goes blank when you try, i do not have a solution, nor does anyone else, so far... either wait, OR try the service center.
regards.

You were right, MTTY is still working. I finally got it working again. It took me several methodes.
I got it in serial mode after flashing it with this ROM (it couldn't get out serial mode) --> http://www.cddnet.com/Support/ma_cdlsku12_wwe_10300_163_10100_ship.exe
The backup i made didn't work. But an other way worked:
The other ROM's didn't work but by first updating the radio file form this ROM --> http://www.clubimate.com/Support/ma_cdlsku1_wwe_10300_143_10100_ship.exe
and then doing the setup complete (ms, nb and radio) it finally worked!!

i have the same problem when i tried to upgrade.
now im stucked with the serial screen, and youre method doesnt work for me, it says unsupported format when i dubble click at radio_.nbf
and when i run a full upgrade it says Modell ID error.
hope someone can help me

Problem with awizard. Please help my device is DEAD

how can I use awizard if I cant turn on my device?
I can only get to Bootloader and when I try to press U in awizard I get a popup window saying my device is not connected.
when I confirm this popup (twice) the dos window state that it is initializing and says not to remove my device from the USB and it get stuck for at least 20 minutes
I cant turn on my device so Im trying to flash some other ROMs (like imate's) but cant do that because of ID issues.
What can I do? I am fraustrated, please help, my device is dead.
Thanks

Hi,
If you device is stuck on bootloader, then you should update it with a no vendor ID rom like the one there are on the FTP ftp://xda:[email protected]/ /Prophet/Shipped_Complete_Updates/
section.
The Dopod one come with no vendor ID, but if you do so, you won't be able to change rom later.
If you have another rom you would like to use, then you should download the file ROMUpdateUtility-NoVendorID.zip in /Prophet/Tools/.
Connect your phone on usb when stuck on bootloader, extract the files of your Update Utilies (RUU ...) and change the executable with the no vendor one. You may have to copy the nbf (or something) file into the same directory as the executable.
Launch it and see if it works.
if it doesn't work then download the no vendir ID dopod rom and run the RUU, it will work but as I said, no turning back for now.
good luck :wink:

Thank you for your answer.
I have tried using this ROMUpdateUtility and it started flashing the rom, but when it got to 95% it said:
Error [326]: INVALID COMMAND
This NBF file cannot be used for your PDA phone. Please check your NBF file.

HELP
anything im trying to do, I still get this black screen with version numbers.
What is wrong?
It not that I have played with the device, it just happened. since then I am trying to flash different ROMs with no success.
Please HELP.

I guess your prophet IPL and SPL is 2.15.xxxx
If yes, the only rom you can is Dopod newest rom.

Please, please, please, please help me.
I have HTC charmer and unfortunately put an dopod latest rom in it & now I am stuck in bootloader mode.
Please tell me & help me as I tried many roms but with no success.
I want to revert back to MDA Compact II rom.
Please Help.
SPL is 2.15

urgent help needed

hi there
i am using imate jamin da problem with my cell is
i upgraded my rom to qtek 2.20000 it was working absolutely fine with 8 icons in my comm manager then i upgraded to RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-b1 and it has severely damaged my cell as my phone my phone hangs white booting it shows me the colour screen with
IPL 1.00 and SPL 2.20.0001
on the Screen
OS and GSM is not displayed
I tried rom update several times but its not working
i tried to update my rom through boot loader mode but again failed
i even tried to format my phone but it gives FAT16 format failed
I even tried to upgrade to jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 but still its not working and givng same problem
now i dont understand what to do
guys please give me Advice and solution for this g3 g4 Problem
i even tried sending my phone to service center but stupid people dont know how to solve it and they returned me back
Thanks in Advance

You have bricked your phone... You just can't install a G4 rom on a G3 phone... Different chipsets are the cause of the problem... Sorry

you mean to say its over ?????????????
there should be any way

You'll have to wait to see if Jesterz manages to produce a goldcard...
BTW a goldcard it's basicly a mem card with a rom in it that autoinstalls itself thus no need for the usb connection... This fits your case cause you don't have an active usb conection because of the driver/chip conflict...

wrong software
I have the same problem i tried to flash my g3 with jesters RUU-Prophet-G4-AKU2.2-2.20-2.47.21-Jester-r1 by mistake and it was ok until the end of process when i finich it with congratulations and bla bla my device stills in the bootloader mode all the time. I can now connect and start to flash but when it comes to 80% of the process it stops with error 360 wrong command. Pleas is there any help for some kind of downgrade flash or so because it can only get boootloader but never start with software. When I try with jesters RUU-Prophet-g3-AKU2.2-2.20-2.47.21-Jester-r1 the whole process finish ok but the phone stills in bootloader. The same thing is also with RUU-Prophet-g4-AKU2.2-2.20-2.47.21-Jester-r1 I can not execute step2

that's why you should read the "sticky" first before you do it.
I have a Dopod 818Pro from a friend of mine but in Chinese ROM, so I have to read a whole nite the sticky and found out what is my Dopod version, finally I found it is G3, so I did all the steps, from unlocked the CID till upgrade to Jester latest ROM for G3 and skip the G4.

please help
Yes i realy know that it was my fault and my big mistake so i vould not do it again but now i need help because it stills in bootloader i i can even start flashing the device that gives me hope that some kind of recovery is maybe possible.

Yes i also commited this mistake its my fault but i really need help my device still enters into bootloader mode.

ur problem
there is nothing to do anymore u have to wait u CANT DO ANYTHING ITS OVER

how do you mean it is over. Do you think that could not repair it. Is it possible with sd card or jesters gold card and how. Help me please if somebody knows

there must b some way to overcome this problem

jesterz's gold card isn't working yet, and for now it's only for G3...

My hardware is G3 but flashed by mistake with G4 and now is in bootloader mode so i can start flashing but i do not know with what and how. Could you please explain me how and where can i find and use goldcard for g3 if possible Thanks

have u tried holding the camera button while softreset and then flash rom again

Yes sure i tried to flash rom from jesters for g3 which is for my device instead jesterz g4 what i used by mistake and it passed ok but when i restart it stills in bootloader mode only, so i could flash but do not know which firmware should i use

i've the same symptomes as mjankovic and aarif_ziaee, (bricked my phone)
but the only things i think i've forgot, is to cid unlock my device before doing the step 2
i have a question.
i have the rom PDAMobiz_Prophet_WM5AKU3.3_v3301
(witch is not an auto installable tile, it's a folder containing exe, dll, bat and nb file)
is it possible to install it by using teraterm pro or mtty? (connected and install bats and cabs by thoses software)
ps : i'm sorry for my bad english, i'm french not going to my languages faculty since i'have bricked my phone. need to fix it soon !

Do You have Problem downgrade fr ROM 2.03 TX WWE

Hi all,
I'm Indonesian. My Device is XDA II Mini. A few weeks ago I have upgrade the ROM to 2.03 TX WWE, used it for about week. A problem appear when I tried to downgrade the ROM to the original one from seeo2.com site the PC tell the error 150 (I think its about the connection).
when I read this forum, i know the many people have the same problem with me.. and still not found yet the solution for solving this problem.
With this situation I made this new thread to share our problem in this thread. Its about the history from ROM 2.03 TX WWE, about the maker of this ROM and for the warning massage for anyone who wish to write this ROM to their device so they will think 100 times to use this ROM.
Lets join this thread and hope there be a nice guy who can solve our problem.
regards
Eric
Jakarta-Indonesia

Hello,
I have the same problem with my magician. I flashed so many times some ROMs on my Magician before without any problems. But since I flashed the 2.03TX ROM, there is no way to flash any ROM. I also can't reflash the 2.03TX ROM. It always says, that there is an Connection Error.
I tried to flash with the official Setup and also with the No_ID.exe, but there is no chance to do something.
The 2.03TX is a very nice Rom, but i want to use the programm "Phone Extender" on my Magician and it doesen't run with 2.03TX...
Please help us someone, I want an other Rom on my Magician!

Where is everybody.....
Please Help us hiek hiek hiek.... cry cry cry....
Does anyone can help us ?????
Pleeeeaaaaseeee......

The same problem, the 2.03TX WWE is a nightmare for me.

I haven't got any problem.
Flashed just last week tx203->TMobile112->wm61.
Very happy with everything, I am using XP and O2 mini

you should flash from bootloader.

I have problem after try flash wm6 from 2.03 TX WWE phone only boot mode ... any help .. I try to flash same rom but I give same error on country id

I have the same problem.
Solution is to enter to the bootloader mode somehow and downgrade to original not bigstorage rom and than flash new cotula rom.
If you can't enter to the bootloader mode with power+camera+reset buttons try to hold longer or rapidly press power+camera and then press reset a few times. I'm succeeded finaly...

to bootloader mode mean screen with serial or usb status ... my problem is I try more rom but any flash I don't have original rom ... what I do?

hello im from Indonesia too...
You can use magicianUpdt_NoID (or another name, i forgot)
you can search at xda-developers ftp..

I have no problem with mine.
When I flashed this ROM it got automatically flashed twice.. I don’t know what happen but it was successful

Hello
I was sucessfull.
There is a 2 step flash!!!
P-O

I try to use this too but nothing no flash ....

Try this rom: http://rapidshare.com/files/18876133/NL_11300_131_11200.exe
If this doesn't work tell me the error message...

ok this img of error the image 1 when start exe the other when stat update noid

jovan.asanin said:
I have the same problem.
Solution is to enter to the bootloader mode somehow and downgrade to original not bigstorage rom and than flash new cotula rom.
If you can't enter to the bootloader mode with power+camera+reset buttons try to hold longer or rapidly press power+camera and then press reset a few times. I'm succeeded finaly...
Click to expand...
Click to collapse
Mine keeps reseting everytime it should go into the bootloader screen.
I can force it, but then the update wont continue anymore.
How did you do it?
---Edit---
Nevermind, found the solution here, its the old vista driver bug... :/
http://forum.xda-developers.com/showthread.php?t=291723

I use xp ...

well... it worked on mine...
Try the driver thingy anyway and follow the instructions to the letter.

I try more and more but notuhing

Here's what I did step-by-step:
- Recharge the battery to at least 70% in a electric charger (not connected to the PC).
- Go into bootloader (press the power button +camera button without releasing and click the tiny little hole on the right bottom side of the device, next to the audio entrance).
- The screen goes black, that's normal, with the help of a bright light you can see its written on the screen "SERIAL" and "V1.02" (or something similar).
- Go into Active Sync on XP (or Windows Mobile Device Center on Vista) and uncheck the option "Allow USB Connections".
- Connect your pocket pc to the PC usb (its still in the bootloader screen, right?).
On Vista (I think XP can skip this step)--------------->
- Go to Control Panel > Administrative tools > Services and start the services "windows mobile device connectivity" and "windows mobile device 2003 connectivity", its they are already running thats ok.
- Now go to Control Panel > System > Device manager, find your mobile device and force the update of the driver attached here.
- Now, press Ctrl+Shift+Esc for Taskmanager and kill "WMDC.exe".
------------------------------------------------------------------->
- Download this rom (46mb): http://rapidshare.com/files/18876133/NL_11300_131_11200.exe (its in english WWE)...
- With Winrar, extract that EXE into a folder.
- Copy the MaUpgradeUt_noID.exe attached here into that folder, with the rest of the files.
- Run MaUpgradeUt_noID.exe.
- If all goes well the update will take a loooong time and pass thru three install bars, that's normal.
- After that it recommends a Hard-reset (Power button + reset at the same time).
Now your rom is official, and you should have no more problems.
Install the Cotulla WM6.1 rom: http://forum.xda-developers.com/showthread.php?t=492937
Based on: http://forum.xda-developers.com/showthread.php?t=291723

Stuck en bootloader

Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)

Please need some help ( a lot)

beastmichel said:
Maybe its in a forum,but I have looked everywere.I just sold my S200
(i bought a HD) and the S200 died...... It is in the bootloader and I have tried everything.
1. Pressing all buttons = Format failed
2. Spl can be loaded again, but no with a exe.
3.All roms can be instaled (but not al exe). If a rom installed 1
file (exe) it doest not work. I installed al least 20 rom (wm5,wm6 ect...)
All can be installed and at the end you get 100 % and finished......
I opened the S200 and the button on/of seems to be ok.
4. In the bootloader sceen I get :
IPL2.09.001
SPL 2.G4.4PDA
I am desperared because I am fixing it since a few weeks with....no result.
PLEASE, I NEED SOME HELP
(PD I am from Belgium and living in Spain)
Click to expand...
Click to collapse
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and

Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??

beastmichel said:
Dear Dioxda2.
Thanks for your comments but I think that I do not understand it all.
My S200 is in the bootlader and I did the following (your manual) :
The pda goes automaticly in the bootloader when on, with the USB words
in the screen :
1.When I try to to inslall a spl , it stays in a green screen with ipl and spl data.Nothing can be installed until baterie is removed
2. Tried to install the NVID but stops ant 80 % with error 326.
3. Tried to install Lazy tool : I put the nbf file in the lib file and install the rom
100 % and I reboot in the bootscreen (fustrating)
4. Tried to insall WM5 and the same like the lazy tool instalation.
Never activesync is connect.That why (I think) that somo roms can not be installed, like a wm5 only os.
Any sugestion ??
Click to expand...
Click to collapse
1. you may safe your prophet ONLY if you successfully flash the NVID, (just don't look at the connection status between PC and Prophet, as it was forced to bootloader mode, just run the NVID and flash dtraight until it ends, be awared that, NVID needs time to flash, sometimes needs more than 5 minutes, so ... wait for it ! )
2. I hope you can make it or you need to bring your prophet to factory due to abnormal flashing (wrong flashing)...
Good luck
PS.
[size=+3]Lazytool......[/size]
you should place your favourite XXX.nbf file next to the "LazyTool-Start.cmd" or "upgrade.cmd", but [size=+3]NOT[/size] in the LIB folder.... +_+
+_+ +_+ +_+ +_+

too bad (
Dear dioxda2..
i think this is the same problem as my S200 (
mine wasnt on the software prob but hardware...
to: Threadstarter )
try bringing your Mobile to any qualified technician near your place.. something might have been wrong inside... like mine its the comm and cam buttons that are grounded thats why its always in bootloader.. no matter what software i flash its still the same...
hope this helps
Mark

Dear Marekplph,
Can you explain me what do you mean with grounded. Do you mean a
short circuit (negative). Is it dificult and expensive to fix ?
Thanks,very helpfull

dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?

noonas said:
I have tried pretty much all the Lazu Guides and prohpet tools.
Most of the time I get the Invalid update tool error.
Maybe the person in this thread has the same problem I have.
I have a G3 Prophet (Qtek S200), that has been flashed with a G4 Rom.
Not it is stuck in tri-color screen and nothing seems to help.
the prohpet tools I downloaded gives me errors and there is little documentation of where to put rom files etc. Maybe you know?
Click to expand...
Click to collapse
if you want to make a fast move, bring it to the factory....
mess up upgrade code (G3 and G4) ... sorry... doomed.

back again
yes in my country its cheap.. coz something inside short circuited and that keeps my camera button pressed and taking pictures of his own < scary > if you cant fix this try to visit an authorized technician that can fix this for you...

ok, will send the s200 to the SAT (repair). I don´t have other options.