i upgrade my dopod 828 CHT to CHS, but the bootloader is dead,
how to fix it ?
urgent~~
thx all ~
dopod said:
i upgrade my dopod 828 CHT to CHS, but the bootloader is dead,
how to fix it ?
urgent~~
thx all ~
Click to expand...
Click to collapse
What do u mean by the bootloader is dead??!!!!! :?
Do u mean ur phone is dead and ur in bootloader mode?
RAGO :lol:
i mean connect pc, the pc show the message is can't recognize my dopod!
andi try to used the romupdate to download to sd card , is same problem~
Can u still see serial and bootloader version on ur screen?if yes,have u tried another USB port on ur pc...Also try another pc...Does the serial change to USB once connected to pc,even if not recognized?...
RAGO :lol:
can see the serial & bootloader ver. ~
but the pc still can't recgonize my dopod~
Try this...Hard reset and connect again but using another USB port....does the serial change to USB?
RAGO :lol:
is changed to USB, than ?
is changed to USB, than ?
then there's nothing wrong with ur bootloader,it's working like a charm.. :wink:
now go to the ftp from here,and download MAupgradeUt_noID.exe,replace ur MAupgradeUt.exe with it,and reflash....that's it...
Good luck...
RAGO :lol:
i try sometime, still not work...
do u have other method ?
Related
Yesterday i tried to upgrade my MDA
But when my updater was at 63% my pc shutsdown (poweroff)
Now my device wont boot anymore.
If i press : Power+Camera+Reset is shows:
Serial V1.00
If i hard reset it shows:
My boot screen with this info:
No GSM
D 1.13.00 WWE
My question how to get it working again, probably via the sd upgrade method used for the bigstorage rom..?
But where can i download a MB1. rom file from somebody..?
i think u mean NB1 file not MB1
first of all did u try to see if it says USB when u plug it into ur computer using the USB cable??
If it does then simply reflash it the normal way
Once ur sure it wont recognize the USB then try the sd card upgrade method ( atleast thats my opinion) and hte NB1 files are created using the nbfdec program to fully understand it i sugest u use the "Magician to 1.13 + 1.13 Radio + BigStorage ALL-IN-ONE" Guide u can download it from the thread of the same name it tells u how to create the NB1 file
docnas said:
i think u mean NB1 file not MB1
first of all did u try to see if it says USB when u plug it into ur computer using the USB cable??
If it does then simply reflash it the normal way
Once ur sure it wont recognize the USB then try the sd card upgrade method ( atleast thats my opinion) and hte NB1 files are created using progr the nbfdec am to fully understand it i sugest u use the "Magician to 1.13 + 1.13 Radio + BigStorage ALL-IN-ONE" Guide u can download it from the thread of the same name it tells u how to create the NB1 file
Click to expand...
Click to collapse
Sorry i mean NB1
If i connect it to USb, it shows indeed USB instead of Serial.
But flashinig wont work then i get a: Get device data error
So the "normal way wont work"
I tryed to flash it via the SD card but, The option:
Press power to flesh doesend appear..
(sure i used all thos methods before so i know what im doing, but now they wont work )
ActiveSync cant connect to it device
Hey guys!
I tried to upgrade my HTC Magician to the MaUpgradeUt_noID.exe Upgrade.
So far so good..
but now my PDA is stuck in some sort of bootloader, and I can't get it up and running again!!!
Please advise!
Greetz from Germany
MDAcDom said:
Hey guys!
I tried to upgrade my HTC Magician to the MaUpgradeUt_noID.exe Upgrade.
So far so good..
but now my PDA is stuck in some sort of bootloader, and I can't get it up and running again!!!
Please advise!
Greetz from Germany
Click to expand...
Click to collapse
Hardreset! Oh wait a Did you connact the device to the USB cable after you put it in bootloader mode? Then it will change from serial to usb.
hendrixus said:
Hardreset! Oh wait a Did you connact the device to the USB cable after you put it in bootloader mode? Then it will change from serial to usb.
Click to expand...
Click to collapse
My Magician can change "Serial" to "USB", but I cannot reflash it.
btw, I tryed MaUpgradeUt_noID.exe and MaUpgradeUt.exe both. The problem seems like the RUU cannot get Magician data.
Need help!
coly said:
My Magician can change "Serial" to "USB", but I cannot reflash it.
btw, I tryed MaUpgradeUt_noID.exe and MaUpgradeUt.exe both. The problem seems like the RUU cannot get Magician data.
Need help!
Click to expand...
Click to collapse
Try pressing the camerautton, the power button and the reset with the stylus at the same time, see how this goes. If it doesn't, then it will need reflashing
cheers mark
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
hehh
same happend to me once. Go online and finde botton run , update utility 2.00.1
go step by step:
Disconnect your phone from the usb cable,disable any Firewall and Anti virus and reboot your Pc.
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t Bluetooth for the Upgrade)
4. When you see usb appear at the bottom of bootloader screen
5. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
After then, install origial ROM. (u can try T-Mobile MDA Software Version (2.26.10.2) )
Let me know if it's working
ty man for ur reply , i have tried every possible solution, including mtty! no luck. from ur post i didnt understand the following
Go online and find botton run , update utility 2.00.1
Click to expand...
Click to collapse
did u mean button rom . if yes , what the 'update utility 2.00.1' ?
ty
can i use mtty to revive my phone? i found some command for erasing my entire rom in the phone , but it doesnt seem to work . help me
Hello XDA Nice Team !
By mistaken i wrote some file to my bootloader in my I-Mate Jam ..
That was after using the bad ROM : 2.03
it's the worst cooked version i saw !
Now my bootloader mode is working .. but no way to connect to PC with USB port ..
My computer does not recognize my Magican when plugged in bootloader mode anymore!
Bootloader Ver: 1.0
is there any way to fix or upgrade or restore original bootloader
Now i cant upgrade or downgrade my magican by any method
Noway to use successful connection with any roomupdate utility
Please help me to fix or restore my bootloader!
Thanks to any one read or replay or try to help or help me to resolve my problem
XDA lover
i'm sorry that happened mate...
i've had success with flash-from-bootloader attempts before, both on my Magician, when i accidentally flashed off of Vista and it'd enter the bootloader every week or on a reset using the reset hole, and also on my Wizard when i ignored warnings from WM5torage and it'd only enter the bootloader
what precisely happens when you connect to the PC, allow USB connections in AS/MDC, and let the phone enter bootloader however it does? i can just flash a rom from there, but i won't (iirc) get any reports of as recognising the device...
My experience:
1- when i plug my sd card into my jam .. usb not recognized in bootloader mood !!
2- when i use puty or roomupdate it reaches to USB> then when i type any command it does not respond !
3- i could do something .. i let my phone bootup and this i-mate logon screen stays 4ever .. i connected my ppc to pc and i could explre my imate by activesync ...
i could reach something .. when i explore my phone and remove everything from startup folder .. my phone boots .. and i can see start botton .. no touch alignment comes .. and everything works .. but.. screen is virtually reversed .. i can see the OK botton but i must click on the facing area and it be clicked ..
i think i executed some wrong hard SPL to my phone ant that happened >
is there any way to resolve this problem?
is there any way to erase flash on my I-Mate Jam????
is there any way flash my phone?
i also have prepaid JAFWM with pkey and USB cable .. no BOX ..
Help please!
that's messed up... howsabout flashing it at the point when the phone boots up? if there's an AS connection there, then it may work... i'd flash to an official rom though
Same problem , PLS Help !!!
Thx for help
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
If your magician isn't detected at ALL by your PC when plugging the USB cable into it (i mean, no new hardware; no unrecognized hardware; nothing is detected in your PC when you plug the USB cable), and unless you had previously made a SD backup of your entire Flash with this procedure ( http://wiki.xda-developers.com/index.php?pagename=MagicianSDflash ), then your only option will be to build a JTAG diag cable:
Here are some general directions / ideias:
Magician JTAG pinout: http://wiki.xda-developers.com/index.php?pagename=MagicianJTAG
How to build/run the JTAG: http://wiki.xda-developers.com/index.php?pagename=DeadBoot
Photos : http://www.cf-box.com/htm_data/55/0912/1679.html
Some interesting stuff for debugging problems: http://pda2u.ru/ptopic205.html
For sure cotulla has one built so to test his ROMs + bootloader - maybe he will be willing to give you some directions if you run into problems, and above all, give you a prepared .nb0 (with the bootloader file) for your magician, which i do not know if there's one out there, extracted from an original ROM.
Anyway, you can always try and do it for yourself using itsme utilities. Follow this link: http://forum.xda-developers.com/showthread.php?t=218643
Regards
Keeper,you're awesome! I'm searching for JTAG,too
xiaojin1985 said:
You should check USB connection I think...
Try plug your battery out of device and wait a moment (e.g.10 minutes) and try again,sometimes it will be fine when you did this.
Click to expand...
Click to collapse
Dear xiaojin1985 ,
Thx for your help, But unfortunately i tried your solution but it dosnt work !
Dear Keeper,
Thanks too for your help,
and i think the solution for my problem is one of the solutions you says ( How to build/run the JTAG: ) ,
but the pictures is not available anymore , so pls can you get the pictures ?
All the pictures are in here:
http://s218.photobucket.com/albums/cc23/alex_beda/ and in attachment there's a .mth file with all the pics built-in.
Don't take it wrong what i'm about to say, but in all honesty if you can't figure this out yourself (digging up the internet for the missing pics), i would suggest that you shouldn't try this, since this ain't easy at ALL...
Just to give you some ideias, it will require you to adapt your magician test point signals (TDO;TDI; nRESET; etc,)seen on the magician pinout pic to what is said; solder very thin wires (best done with a small hot air tip); fixate the small dip switch (micro switch) to be always on; keep the USB connected...idk... plus alot of other small details which ain't easy to accomplish.
Personally i haven't tried this yet but for sure it would work
If you decide to go ahead, please post some results!
Connection error solution
this is my problem
hi all. A friend of mine gave me an S100, and after i played for a few days with it, i decided to update it's rom. A "country error" problem appeared,cause i have the greek version, so i ran MaUpgradeUt_noID.exe which completed (as showed 100% process). My (new) problem is that i cannot update anymore. Every time i enter boot menu, i ran the upgrade
(HTCMAG_ROM_WWE_O2.rar) following all the steps normally. When the device resets (so the upgrade is going to start), it's re-reseting again and showing ERROR 101 connection error. Any ideas?
Qtek Greek version
R 1.12.00
G 1337.42
D 1.12.00 WWE
P.S. apart the problem everything is function properly
and the solution
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe radio_1.11_greek but idont reset the qtek in first screen
and upgrate downgrate start all ok
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run MaUpgradeUt.exe MagicianRadio_1.12.10. uk but idont reset the qteki n first screen
upgrate from radio 1.11 to 1.12.10
reset
welcome screen
hard reset
plug usb (uncheck allow usb connection in activesynch )
run HTCMAG_ROM_WWE_O5_251209
everything is ok my magisian run the new Rom
here..........................
HI i search forum and i dont find answear. I flashed many roms but i never had any problem with usb connection with PC. So when i flashed new ROM and kaiser restarted when the new ROM started to boot windows shows info "USB device not recognized" i tryied reinstal drivers, reinstal AS, tryied mtty method, tryied flash ROM from storage card (dont work, meybe i do something wrong i founded 1 thread but i dont know do it work). Guys plz helpp me sry for english i am from Poland.
medeis_jar said:
HI i search forum and i dont find answear. I flashed many roms but i never had any problem with usb connection with PC. So when i flashed new ROM and kaiser restarted when the new ROM started to boot windows shows info "USB device not recognized" i tryied reinstal drivers, reinstal AS, tryied mtty method, tryied flash ROM from storage card (dont work, meybe i do something wrong i founded 1 thread but i dont know do it work). Guys plz helpp me sry for english i am from Poland.
Click to expand...
Click to collapse
Go here- http://forum.xda-developers.com/showthread.php?t=396922
And look into the force-USB Hard Spl! You may need to change your Hard Spl! Remember to use jump spl to flash!
I usually just disconnect data cable>kill all the mobile processes on my pc using task manager>restart pc and it always works.
redbandana said:
I usually just disconnect data cable>kill all the mobile processes on my pc using task manager>restart pc and it always works.
Click to expand...
Click to collapse
Hey Red, I see you got your calendar working! Yea I have never had an issue with my usb, but I saw that he flashes alot and it kinda fit the explanation for force-USB!
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
medeis_jar said:
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
Click to expand...
Click to collapse
Can you get into the bootloader? Maybe reflash the ROM from bootloader mode!
I have harspl 3 56 flashed, the bootloader mode working, but windows dont reconigze my kaiser...
medeis_jar said:
dash... thx for link to thread but i cant copy nothing to my device..... and RUU aplication dont find any device, killing all proces of mobile dont work too....
Click to expand...
Click to collapse
no you don't kill the processes on your mobile. you kill them in your TASK MANAGER application in windows on your pc NOT your pcc/tilt/kaiser/device then restart your computer and connect once windows is fully loaded.
edit:
These are the programs that are running on my computer associated with data sync:
1) WmdHost.exe
2) mobsync.exe
I killed proces on my computer in task menager ;] restarted and nothing happened...
medeis_jar said:
I killed proces on my computer in task menager ;] restarted and nothing happened...
Click to expand...
Click to collapse
Try uninstalling activesync on your computer then re-install it! I have heard of that working in the Herald thread!
medeis_jar said:
I killed proces on my computer in task menager ;] restarted and nothing happened...
Click to expand...
Click to collapse
ok then open Windows Mobile Device Center on your computer>Mobile Device Settings>Connection Settings>Allow USB Connections
read my first post i tryied that,...
i tryied mobile center doesnt work too...
medeis_jar said:
read my first post i tryied that,...
Click to expand...
Click to collapse
doesn't state that in your first post. It just says you never had a connection problem.
If you manually go into bootloader and have data cable connected does it say serial or usb at the bottom?
redbandana said:
doesn't state that in your first post. It just says you never had a connection problem.
Click to expand...
Click to collapse
Hey Red, happy 1000 post day! Your bigtime now!
Yes but i wroted that after flash new rom i had and tryied reinstal AS ;] sry for missunderstanding
in bootloader write usb when is connected, when i put of cable write bottom
dashmaster1000 said:
Hey Red, happy 1000 post day! Your bigtime now!
Click to expand...
Click to collapse
thanks dash and thank you for all the suggestions regarding the calender
medeis_jar said:
in bootloader write usb when is connected, when i put of cable write bottom
Click to expand...
Click to collapse
Then you are connected to your computer even though it doesnt say on computer! Go ahead and flash a new ROM! As long as your bootloader says USB you can flash!