Hi everyone
In need some advice. I think my device is dead.
I`ve updated my mda about 5 times and i never had any problems now i updated my device with rom version from qtek.nl version MDA_TA_WWE_DutchRetail_11200_550_11200_ship but at the second part it hangs up at 47 % and gave me a error, like de message sad i disconnect my device soft reset the device and tried to update it again but it`s not working.
If i connect my device on my pc it does not show up, also if i connect it to the power suppl now light is burning (so i think it`s now charging) the only thing i see on my device is the QTEK logo and some kind of picture of a night city below i see R 1.12.00 / 1337 42 / D 1.12.00 WWE on the left side i see the logo of windows. I have removed the battery but still i see the same screen and i can not turn it of.... if any one can help me with this pleas let me know.
Related
heyy....i have got this menacing problem with my prophet G4
2.13.0001
2.13.0001
02.20.21
2.13.9.23
when i switch it on...it goes till the blue screen showing imate and the versions of IPL/SPL etc given abv but then shows a white screen and crashes.. hv tried a soft reset/ hard reset but it duznt format....i have downloaded two roms one is JAMin_WWE_2130923_21309112_02072_0ship from clubimate.com and Prophet_orange_uk_ROM. i go into the bootloader program with three colored screen and when i connect it with the usb the "usb" comes at the bottom left of my imate jammin.....but PC doesnt recognize the device saying "windows cannot recognize the device or it as malfunctioned" active sync obviously doesnt connnect then! and i get error 260 Update error saying that PDA cannot be accessed or something...HOW DO I SOLVE THIS PROBLEM frustration
thanx in advance
I've been running a ROM I built from the consolidated kitchen this weekend without any problems. Today I updated the radio to 2.69.11 from the cingular 2.25.11. After the flash the phone froze on the windows mobile screen. After some time I tried to reset the phone and it froze again, a few more tries and it finally boots up. I didn't pull the memory card when I flashed and thought that might have been the problem so I flashed again even though the phone was showing 2.69.11. I don't remember everything after that but it wouldn't boot up and I have tried flashing the original Cingluar ROM & T-mobil 2.26 without any luck.
The phone is stuck in bootloader now and is getting a error code 302 I think it's because the phone doesn't stay on when the USB cable is attached. It gets to about 15% and the phone resets and the error 302 pops up. When connected and not trying to update the phone turns on and off in the bootloader screen. I have pulled the battery, rebooted the laptop, tried using mtty,and pulled the sim. I thought the original problem might have been because I flashed at 52% battery. I put a older battery in after that appeared to have a good charge. Right now I put the phone on charge with the newer battery to see if this helps. I am not sure if it is charging because the orange light is not on, I can't get the phone to stay turned off when plugged into the charger and the bootloader screen is on.
And yes I have been searching for hours for a solution to this problem.
Also looking for a post I read about doing a master reset, I have tried holding the 2 soft keys when turning on, didn't help.
I think this says it all I have tried everything, does anyone anything else to try?
Thanks
UPDATE: went out for a few beers and some food. Not sure it the battery charged (bootloader screen on the whole time it was plugged into the charger)
Tried flashing again with cingular ROM, got about 20% and phone shut off and turned on again in bootloader. Flash gave 302 error again. Tried again and phone reset (on and off) every 5 seconds when connected to laptop with USB.
I'm hopping someone out there has a answer for this problem.
Back from the dead HALLAULA!!!!
This morning I spent more hours searching still didn't out find anything.
I tried mtty again and noticed that I never got to the screen that shows USB>
to enter the command "set 14 0"
I came up with a thought and this is what I did. Created a new ROM, OS only. Thinking it will load faster than any other ROM. It reached 100% in 3 minuets the whole I'm coaching come on baby don't restart and than going (don't know how to explain the feeling) waiting the next 2 minuets to get to finished. But it got there booted fine. I don't know why it stayed on this time and didn't restart, maybe having the battery out all night had something to do with it. After I flashed the Cingular ROM than the original I created and lastly Radio 2.69.11
I hope this helps someone in the future,
i need your help
hi man I had a prophet s200 and give me the same error 302 but, with the diference in my case got 98% adn then stuck in boot screem, please help me if you can...and sorry for my english
Guys,
It may help checking out this thread!
http://forum.xda-developers.com/showthread.php?t=294107
Can you help me out?
How did you create a new ROM - OS only? I'm having the same problem..can you walk me through this?
Thanks
How did you create another ROM (Operating System only)? I'm having the same problem and I have tried for the past 2 weeks - but no luck. Can you walk me through it?
Thanks
I used the consolidated kitchen (sticky at the top of this forum)
Uncheck everything on Build OS.
My problems started from a version of battery status that caused the original problem and not having enough of a charge on my battery.
Make sure you are CID unlocked (if you have a G3) and your battery is charged.
Umm, you can't uncheck everything in build OS or you will have problems, especially if you don't check a tuchflo or non touch flo dll or choose a commanager and probably a few others things. I don't have build OS up in front of me to check. The whole point to this msg is that you can check everything in build OS (besides the ones that say choose only 1) and it will build an OS only rom for you. That's the whole point behind build OS.
You are correct, I was kind of going from memory since I had built the striped down ROM awhile ago.
It may be that my q-tek is bricked. To cut a long story short I am rebooting and it is getting stuck on the QTEK page displaying:
IPL 2.20.0001
SPL 2.20.0001
GSM 02.47.21
It also had OS2.20.7.34 but this is not showing.
Problem is - this is a swisscom fone and therefore I cannot access the original QTEK site as it fails to recongise my IMEI.
I have also tried in my ignorance to reflash it but now its stuck.
Is there anyway I can have access to the original English software so that I can try to reflash and re-install from scratch?
I also wanted to add that even a hard reset is not getting it to start up.
And another thing - sometimes the screen just freezes and breaks up in line and colours. What is that? Is my fone dead or dying?
Any help will be appreciated.
Delgada
The three colour screen is bootloader. If you can get that, your device is recoverable.
edit: http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery
This does work, I wrote it from past experience....
Hi,
thanks for your help. Did all your link said.
IT LIVES AGAIN!!!!! THANKS
One question though - if my fone still goes off and the screen feezes and fades out or breaks into lines - what sort of problem would that be?
Cheer!
Delgada
Depends... It could be the ROM, it could be the ribbon cable connecting the screen to the motherboard, it could be an IC (but I doubt that as you say it works)...
Hi.
I realised that last time i opened my Qtek something must have not been in place as I was pressing the case and the pda was freezing. I opened it up for the umpteenth time and made sure all contacts were ok and closed it carefully. It now works fine. Last hiccup - getting it to read my home wifi when it reads everyone elses already.
Thanks
Delgada
Hello girls and boys,
yesterday my TC first stuck in tricolor screen and shows
POLA100 RUUNBH
SPL-1.25.0000
CPLD-2
and downwards: USB or SERIAL
It happened as I tried to flash back the original Radio for it. The update monitor showed ERROR 262 (0%), before that I had already installed signed_RUU. for original German WM6-ROM and it worked fine exept the decreasing GSM connection.
After that I searched here the whole night for solutions but none of them (MTTY, Radio Murata, UN-SPL, flash Radio or OS from microSD) helped.
I guess it's all I am able to!
Maybe one of you guys can help me?
Or can anybod tell me whether my TC is dead?
Can anyone tell me the meaning of:
POLA100_____________RUUNBH
SPL-1.25.0000
CPL-2
Thats what my tricolor screen shows!
Maybe someone can tell me where I can get the original German RUU....ship.exe for Polaris.
Did you install HardSPL before playing around with your phone?
Yes I did, and it worked fine exept the bad radio issue.
My TC started to hang as I tried to get back.
Good day if I'm in the right place, I would like to report a HTC P3300, was originally in French under the wm 5 it was in a Paris shop that I purchased it after a while I did an upgrade if I do not mistake by HTC
and stayed for so long with wm 6, later began to check websites and forums on new roms, unlock the USPL and installed several versions until I found one in English to 6.5.5 was the most beautiful and functional I found
is provided by MMS, but look great i found another more beautiful, but asked to switch to the USPL ELF_USPL 1.17.000 AND SYSTEM accepted and requested to download the Rom version 3.19.4.3 of WM_23138_FULL_UPLOAD,
there was the biggest blunder I made, but the process has started arriving around 3% of the process was interrupted and the screen of the P3300 is gone along with all the leeds yet energized with the bottom of the screen a little clearer when it rebooted already returned
with the screen totally black and no longer lit leeds, I tried all the processes of red soft reset and reset all, when you go to boot loader it does not appear, but charges the battery by USB and wall fountain, if you connect the USB cable PC and PDA hear a beep
strong on the PC that is characteristic of the PC found a device, leed top of a wink and just, always black screen, the icon appears as POCKET PC USB SYNC but
IS NOT NOTHING MORE, BEFORE RETURNING TO A WORKSHOP which is 700 KM from me would like to know of you who understand this system, I think he lost the firmwere the rom and would like to know what and how it is being reset firmwere the tools with which to do it, if I could at least enable the boot loader would have a hope that he does but not all, the sign of life that is left is only the flashing red leed upper right when you insert the USB and appears Icon on the PC and when it introduces the USB wall fountain, but Windows Device Center does not recognize, do I have any hope? Greetings to all who can guide me, thanks.
: O