Hi,
I am having a problem with the Bluetooth on my Orange SPV C600.
i can't transfer files photos and other files via bluetooth even the other device is paired perfectly with my c 600
i have even checked with smart explorer still same
what it could be????
no one knows i think its the bug in the spv c600
...first of all, my configuration:
G3 Wizard (i-mate branded)
- IPL/SPL 2.18
- radio 2.37.11
- NBD 7.4 touch
my phone works perfect all time but 1 hour ago I've connected it to my pc and SURPRISE: no power light and no charging....
O__o i've changed my usb cable but...nothing!
I've tried to connect to power usb cable (original shipped with my wiz...): nothing at all....PANIC!!!!
hard reset....no solution!
i've tried to connect cable very slowly and...now it's charging but....
...NO ACTIVESYNC!!!
i've tried to connect/disconnect some times and power charging is perfect but NO activesync...
ANY IDEA????
------
extra info: last efficient connection is via WM5torage to a customer notebook...and it works ok
now...also via WM5torage NO DATA TRANSFERT
in bootloader mode it connects...and i downgraded succesfully to last official wm5 italia i-mate rom.
...but no connection
did you try another computer? or the power adapter that plugs into the wall?
yes, of course!
pr0naLd said:
did you try another computer? or the power adapter that plugs into the wall?
Click to expand...
Click to collapse
...it's a good question: too many times it's a joke...but not now.
i've tried in 3 computers...and the response is the same: NO connection, no "usb error"...nothing...only power charging....
If I put (with camera button and softreset) in bootloader mode it's ok...
"bip" on computer and USB un the bottom of the tuchscreen.
I've upgraded anothet time to NBD 7.4 but...
NO CONNECTION
This doesnt really belong in the wm6 forum i think. but maybe you also got a bad activesync on the computer, just start everything fresh again
...usb activesync now works!
after 7 (seven) downgrade and upgrade wm6 -> wm5 -> xda6 -> wm5 -> xda6r2 -> wm5 & so on....
ACTIVESYNC NOW WORKS!!!!
(obviously SAME computer, same Activesync 4.5, same USB port/cable)
i don't know why....but...
I'm HAPPY
thanks to all!
tommaso
TauRho said:
...first of all, my configuration:
G3 Wizard (i-mate branded)
- IPL/SPL 2.18
- radio 2.37.11
- NBD 7.4 touch
my phone works perfect all time but 1 hour ago I've connected it to my pc and SURPRISE: no power light and no charging....
O__o i've changed my usb cable but...nothing!
I've tried to connect to power usb cable (original shipped with my wiz...): nothing at all....PANIC!!!!
hard reset....no solution!
i've tried to connect cable very slowly and...now it's charging but....
...NO ACTIVESYNC!!!
i've tried to connect/disconnect some times and power charging is perfect but NO activesync...
ANY IDEA????
------
extra info: last efficient connection is via WM5torage to a customer notebook...and it works ok
now...also via WM5torage NO DATA TRANSFERT
in bootloader mode it connects...and i downgraded succesfully to last official wm5 italia i-mate rom.
...but no connection
Click to expand...
Click to collapse
I had a problem like that once, I discovered it was my firewall blocking me out of active sync. I had outpost firewall, I disabled it and it connected perfectly
tphan2k3 said:
I had a problem like that once, I discovered it was my firewall blocking me out of active sync. I had outpost firewall, I disabled it and it connected perfectly
Click to expand...
Click to collapse
Yeah I use Cisco VPN for my work, and it screws up ActiveSync at times. Sometimes allows my phone to connect with no problem, and othertimes won't allow activesync to see my phone. Usually turning off the enhanced check box in the USB to PC connections settings will get around it, but not always.
USB port not working
Hello,
I have similar problem.
My I-Mate K-Jam NOT connecting via Active SYNC.
and When i put my device in BOOTLOADER mode there is no appear "USB" below the screen
But only it is charging WITH WALL CHARGER and WITH COMPUTER when i attach to PC
And therefore i can not upgrade my device with usb cable. Can you help me?
HOW CAN I CHANGE MY ROM WITHOUT USB CABLE??
I have tried a few search on this forum but i couldnt find a solve about that.
Sorry for my poor English. I hope i told well. Thanks your advance.
-------------------------
I-Mate K-JAM
IPL : 2.16.0001
SPL : 2.16.0001
GSM : 02.07.10
OS : 2.16.9.1
-------------------------
try this....
loverbadi said:
Hello,
I have similar problem.
My I-Mate K-Jam NOT connecting via Active SYNC.
and When i put my device in BOOTLOADER mode there is no appear "USB" below the screen
But only it is charging WITH WALL CHARGER and WITH COMPUTER when i attach to PC
And therefore i can not upgrade my device with usb cable. Can you help me?
HOW CAN I CHANGE MY ROM WITHOUT USB CABLE??
I have tried a few search on this forum but i couldnt find a solve about that.
Sorry for my poor English. I hope i told well. Thanks your advance.
Click to expand...
Click to collapse
i don't know if this one is a real solution...but...try this (no risk):
- first of all: try to change usb cable (with an old cable my kjam cannot connect....)
- try to plug usb cable SLOOOOOWLY: i've found that my kjam "communicates better" with my old pc il cable is "half-connected" (not tottally plugged in....
and...i don't know if it's possible to upgrade rom without usb connection....i'm sorry
(and sorry form my real poor english)
tommy
Similar problem
This may possibly not be the solution but I had a similar problem. I have an O2 xda mini s and after several days searching I discovered the problem. I opened up the xda and discovered that where the mini usb was soldered to the board, one of the solder points had come loose. The usb was not loose enough to stop the xda charging. By pressing down on the loose solder point the xda immediately showed up and syncing with my pc. I have now resoldered the usb back down and it works fine.
I hope that this is not the problem as it is damned fiddly soldering it back in place.
Hope this helps
I solved my problem
Hello Friends..
I have solve my problem,
I opened the k-jam and renewed the point of usb port with solder machine.
Now it is well working. Charging and sync.
If you have similar problem so i think you can try this one.
But i think you must very carefully.
Solder machine must be very thin.
loverbadi said:
Hello Friends..
I have solve my problem,
I opened the k-jam and renewed the point of usb port with solder machine.
Now it is well working. Charging and sync.
If you have similar problem so i think you can try this one.
But i think you must very carefully.
Solder machine must be very thin.
Click to expand...
Click to collapse
Have you been using some kind of holder for your wizard on your car?
I have seen several USB connectors with a bad attachment to the PCB because it has been used with car Holders that had the USB fixed.
Hi guys,
Recently I bought Imate 8502. Everything works fine. I have installed tomtom 6.01 for wm6 (which works fine on my other htc p3600i)
Now problem in in Imate 8502 when i go in to the settings>External GPS>Hardware... it shows me "gps Hardware port "(none)". If I select any port and press ok and open it again, again it shows "(none)" in gps hardware port. So whts wrong with that.
Also tomtom is not working in Imate 8502. in tomtom software setting doesn't show gps port.(like in htc p3600i gps settings shows that gps in com9). I tried too much to solve this problem but got failure and failure. So I am asking help from any expert here.
Please help me.. I want to run GPS software in Imate 8502
Thanks in advance
1. u need to turn on gps manually
2. u need GPSgate
Thanks
Thanks netnerd,
well i turned it on manually as well but same things happens ?
by the way how does gpsgate will help in this problem? I have no idea of this software.. Though i have downloaded demo but I am not getting this software
thanks bro !!
waiting for your reply
tomtom cant see your build-in gps port
GPSgate will make a virtual gps comm port that gps programs able to see
Need Some knowledge
Dear Chintak i also have an 8502 but still serching for upgrade as u said u upgraded it with tomtom it realy works and how is the procedure to upgrade
will appriciate help .
hi ayesha,
I didn't upgraded anything in imate, I just installed tomtom for ppc.
but tomtom can't read gps port so m looking for another option
OK - hope this helps some....
I have the I-mate 8502, and TomTom 6 running fine.
Things I did:
- Installed TomTom...
- Went to Wireless Manager and enabled GPS. These are my GPS settings by tab (can get to them via Wireless Manager):
>Programs: GPS program port - COM9 (default setting
>Hardware: No GPS port specifed (not needed) and baud rate 4800 (again not needed) - these are default settings
>Access: Manage GPS automatically is checked (again default)
The only setup in TomTom was to set the GPS device to the IMEA option.
TomTom should see the device, but display a message that no gps satellites found or it searching. It usually takes a couple of minutes for the GPS to pass through satellite information to TomTom first time but it then works great.
Running the Telstra WM6 Rom
I followed Rathalian's instructions and it worked perfectly for me too.
I did have to select COM9 as the COM Port of the GPS device in Tom Tom Configuration.
I am also using a Telstra WM6 ROM.
Thanks everybody its working now thank you very much everyone
i-mate 8502: Anybody sells display or phone? /alguién vende pantalla o teléfono?
Good afternoon, folks
I was relatively happy with my i-mate ultimate 8502 till I dropped it and the display broke.
As I'm against buying new stuff if you can at a reasonable price fix something, I'm asking:
is anybody willing to sell almost altrusistically a display or even the whole phone? We could do it through the normal channels (paypal, google, ebay,whatever). Or in person, I'me based in Spain.
Warm regards,
Manuel
I am running Dr. Martin Gonzos Windows Mobile 6.1 v1.1 on my Vox and have got myself Tom Tom Navigator 6.030 with GPS driver v1.20 installed.
The problem is that I am trying to connect my new Holox BT-541 GPS receiver to my Vox but I'm having difficulties.
I can connect the device with bluetooth OK, but after reading some posts I also have to specify a COM port. Here lies the problem. When I try to add one the options are greyed out.
Is there something else I have to enable/do first? Or have I bought a dodgy GPS?
Please let me know if you need any more info as a resolution to this dilemma would be grately appreciated.
Thanks in advance
/cerb
HELP!!!
I have a problem...
I got hermes (HTC TYTN) with WM6(ROM version: 3.22.110.1) and few days ago it had WM5.
Now when I plug the USB in it NOTHING HAPPENS the tytn is acting like on filler and there is no change on computer (i have xp and vista)...
It dosent pomp out nothing and device manager is decime (I didnt do Upgrade from wm5 to wm6)
What happend??? How can i fix these???
sorry for bad english