Database Info

Need Help with my Qtek S200. It is frozen!!

Ladies and Gents - Hi!
Dunno if you can help me but my Qtek S200 is freezing when it starts up. I have tried....Really. I have been through this forum to try to find solutions to my problems. The phone was a swisscom phone when i lived there and has additional Swisscom software on it. But when I did once hard reset, it had normal Qtek stuff on it. Anyways, that is for background purposes.
I got so far as follows trying to revive my phone.
a) When I switch on the following numbers come up:
"IPL 2.09.0001
SPL 2.09.0001
GSM 02.07.20
OS 2.9.7.24"
The screen then freezes!
b) I therefore tried a hard reset....Photo and Comm buttom depressed and a stylus reset. Phone says -
"Press send to restore factory default, Other keys to quit"
....which I do... I press the green send button.
Phone says -
"Formatting FAT partition Format is completed!!"
....again, up comes the same screen as mentioned in a with same numbers and all!
c) So - I press the photo button and the reset to get the red/green/blue screen.
Phone says -
"IPL 2.09.0001
SPL 2.09.0001"
I plug my cable into the computer and plug the cable into the phone. Bottom left hand corner says "USB".
At this point I suppose I should "flash" my phone. Cannot figure out how that is done or even what it means. Tried to find .exe files on the QTEK CD I got with the phone but there seems nothing I can flash the phone with.
This is as far as I can get. Wish I can revive the phone and if I can upgrade the OS software that would be just wonderful!
Please Help (In non technical language as I get lost in the jargon)
Thanks in advance for your replies!!!
Jim

Also, if I may add, the cd does not seem to have any 'system' software on it and will only let me repair damaged programs on my computer. CD is the microsoft Qtek CD with windows mobile 5.0 PPC Phone edition GSM w/outlook 2002. Is that what I need coz its the only cd that came with the phone.....
Thanks again!
Jim

after step (B),wait....it takes some time...

tonydeli7 said:
after step (B),wait....it takes some time...
Click to expand...
Click to collapse
Thanks Tony.
It seems to freeze after step B. 30 mins and it will not change. And it comes up with the swisscom welcome page..... just as though the format of the FAT never happenned.
Jim

So! just for the sake of it I tried again since my last post. Not a thing the phone was and remained frozen even after my format of the FAT. That is almost 2 hrs waiting.
Jim

jimboy said:
So! just for the sake of it I tried again since my last post. Not a thing the phone was and remained frozen even after my format of the FAT. That is almost 2 hrs waiting.
Jim
Click to expand...
Click to collapse
flash a new rom.. The AKU2.2 no vendor(NVID) rom link,is posted in the WM6 Upgrade.go there and download it...

tonydeli7 said:
flash a new rom.. The AKU2.2 no vendor(NVID) rom link,is posted in the WM6 Upgrade.go there and download it...
Click to expand...
Click to collapse
Erm... this is where I become computer illiterate! Where do I find the upgrade and what exactly is flashing? Is it running an executable code when fone is in bootmode and it will do all itself?
Thanks
Jim

Step by Step Instructions...
http://forum.xda-developers.com/showthread.php?t=310452
You dont need to flash up to WM6.... but this should help you to atleast flash up to aku2.2

jimboy said:
Erm... this is where I become computer illiterate! Where do I find the upgrade and what exactly is flashing? Is it running an executable code when fone is in bootmode and it will do all itself?
Thanks
Jim
Click to expand...
Click to collapse
just enter bootloader and run the exe...

So I guess a word of THANKS is Definitely in order. The phone is up and running again with the files and the help that you suggested.
I have stopped the swisscom autorun from installing the swiss stuff on it as I am wondering if it is all the additional software including tomtom and rail timetables, translation programs etc that are filling the memory, slowing the pda and basically crashing it!!!
Again.... a big thanks for your help and support! I had already written the fone off.
Jim

Need help

I flashed my Qtek 9100
i followed the instruction
but now it freez in boot page
MY IPL 2.21.001
SPL 2.21.0lip
OS 6.1.1
Please need help

did you try hard resetting? press power on the top. and turn back on after a moment. then try soft resetting.

yes i tried it but stil freez in boot page
IPL 2.21.001
SPL2.21.0lip
GSM02.25.11
OS 6.0.0.1
please any help
MY PDA doesnt connect with my pc anymore

did you flash it right step by step? things should be alright if you did. if you did, try reflashing with different rom. hopefully you didn't cidunlock it wrongly.

No Free CID-Unlock for G4! Ignore what longjuanfeng say.
Now, get your Qtek stock ROM and flash it, then you will get your orginal OS back.
Then, get another WM6 ROM, HardSPL/SoftSPL your device and try flashing again.
I hope you didn't use ShellTool to flash your G4 device. As it is proven unstable. As you are using HardSPL, you should use RUU to flash your Wizard directly.

Hallo
Can you please Tell me where i can get my Qtek Rom?
When i turn the PDA on it Stay in the boot image Freez that all
but if i boot it into SAFE MODE i get 3 colors i think there is oplossing isnt it ?

cyberbot said:
Hallo
Can you please Tell me where i can get my Qtek Rom?
When i turn the PDA on it Stay in the boot image Freez that all
but if i boot it into SAFE MODE i get 3 colors i think there is oplossing isnt it ?
Click to expand...
Click to collapse
You need to read the wiki!!! The answers to all your questions are right here
http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard

Hello
thanks for the help
i have Tried to get the old image back
now my PDA start normal but it stay in one page Called Align Screen(i installed Love them before )
it Said ( Tap the Target Firmly and Accurately at each location on the screen, the Target wil continue to move until the screen is aligned ).
i have tried it like 5 times but it doesnt reacte like making joke with my self

cyberbot said:
Hello
thanks for the help
i have Tried to get the old image back
now my PDA start normal but it stay in one page Called Align Screen(i installed Love them before )
it Said ( Tap the Target Firmly and Accurately at each location on the screen, the Target wil continue to move until the screen is aligned ).
i have tried it like 5 times but it doesnt reacte like making joke with my self
Click to expand...
Click to collapse
Try to hard reset it and see what that does.
Hold down the Comm Manager button(top left) and Voice Command button(top right) buttons while performing a soft-reset (depress the reset button using the stylus); after you depress the soft-reset button, contintue to hold the two side buttons until you are prompted on screen [you can release the side buttons now]. Press the Send (Talk) button (i.e. the left telephony button) - or whichever button your system prompts you for.

i did what you said i have seen formate complet FTA ect...
Now i get in the Windows Welcome Tap the screen to set up your Windows mobile based device if i click there i be direct to the same ex page with move the tap ect...........
i have notice my OS number has been changed from 6.0.0.1 into 2.0.1

cyberbot said:
i did what you said i have seen formate complet FTA ect...
Now i get in the Windows Welcome Tap the screen to set up your Windows mobile based device if i click there i be direct to the same ex page with move the tap ect...........
i have notice my OS number has been changed from 6.0.0.1 into 2.0.1
Click to expand...
Click to collapse
The screen still won't align? Is that correct?

yes it asked me to keep clicking to be algined

I would try this, post #3 is what you want to look at. Hopefully this will work.
http://forum.xda-developers.com/showthread.php?t=347539

Thansk so much
you saved my ass
it worked
but i just got email from reset factory emails
Here are your activation details:
Activated Product: Mobile Magnifier Pocket
Activation Date: 3/3/2008
Expiration Date: 4/2/2008
Activated Product: Mobile Speak Pocket
Activation Date: 3/3/2008
Expiration Date: 4/2/2008
what i understand that my Device will lock after one months in trial
How can i Active my Device?
And Also if i trired to Edit My contact it said they are locked and need to update the RADIO
nay help please?

Help!! Can I Revive My Tornado!!!

Hi. Can someone please help me out? I was trying to flash my cingualr 2125 from wm 5.0 to 6.0. I was using Kar Hoe's instuctions and I used the typhoon instuctions instead of the tornado instuctions. I didn't know there was a difference at the time.
I did all the steps up until step 5 on the typhoons where it states you will get a white screen. At that point, I accidently hit my usb and the phone disconnected from active sync. I thought if I took my battery out, I could just do a reboot and get the reboot screen. Well I got nothing. I cannot even turn the phone one. I cannot even connect to active sync. I thought maybe I fried the battery and bought a new one and no luck. I have done a hard restart and all other things that I could think of.
Does anyone know if I had hurt the phone and if it can be fixed to get to the bootable screen. I would be happy just to get it to power on and stay with wm5 just to have the phone working.
I really appreciate your help.
Khernden69

Aah i remember doing the same once i screwed up my newly acquired tornado with typhone rom. phone was dead no bootup screen nothing, i tried every thing asked everywhere, thankfully i had warranty period so went to them with very innocent face and made up a story that "i switched it at night and it wont boot in the morning" they bought and gave me a new phone after a week. any ways GOOd Luck

Enjoy WM6

think your in trouble mate. Using the wrong rom and cancelling it half way is a big no no. Least you have a fancy paper weight

Similar problem
I have just acquired a tornado (in it's o2 guise) and it will only get as far as the wm splash screen. I thought trying a hard reset or flashing it with a new rom might revive it. However I tried hard reset (holding down the 2 soft keys beneath screen while pressing power button?) but it just kept booting to the splashscreen. The phone doesn't boot far enough to be recognised by Activesync so can't flash it. Can anyone suggest a solution? Would going to bootloader mode allow me to flash it? If so, how do I do that?
Thanks

try this.
1.switch off phone
2. remove battery
3. re install battery
4. hold camera button
5. while holding camera button plug usb cable to port
6. after some second u will see three color bootloder screen
7.format binfs
7. then u can flash correct tornado rom
you can us alternative method for going to bootloder mode
hold camera button while holding camera button press power button(not hold)
GOOD LUCK

Hi fayizk1
Thanks for the tip. Just one question, will this command CID unlock the phone too? It's just the phone isn't CID unlocked, I've tried using instructions and tools on other threads to change the CID value of downloaded roms to that of my phone, but all Typhoonnbftools produces is a 512 byte .nbf file which isn't good for anything. Any suggestions?

binfs not allowed!
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?

First off, try a couple different times. The "format BINFS" command is case sensitive - where your capital letters are makes ALL the difference. You may need to try a couple times, but I believe "format" is all lowercase and "BINFS" is all capitals.

Thanks djsleepwalker but I tried your suggestion and tried a few times in different cases but still got "Not allowed operation". (If all caps I get "Invalid command") I read somewhere that I'm getting this message because the phone is not CID-unlocked?

Tried a few times in different cases, still get "Not allowed operation". I read somewhere else that I'm getting this message because the phone is not CID-unlocked? Well I know that otherwise I would have just flashed another rom. Problem is I have tried using Typhoonnbftools to change the CID over numerous roms, the file it produces is only 1kb or smaller which is no good for anything. I feel like I'm running out of options...

Just try to flash with a legal WM5 ROM from the magnufacture's web site while the device is in bootloader screen. I hope it will work.
Good luck

This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.

Won't help
timwb said:
This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.
Click to expand...
Click to collapse
Well, I found 'magic' WM5 for SDA, but since it CIM locked, and upgraded to radio 2.0, phone refuse to upgrade (downgrade) to WM5, he said I needed newer file or something... It's stucked in bootloader

I come from China IOICN, but I can not help you, because my bad English.

timwb said:
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?
Click to expand...
Click to collapse
try first
info 2
then
format BINFS

Still says "Not allowed operation!"

timwb said:
Still says "Not allowed operation!"
Click to expand...
Click to collapse
can you get any information when you try "info 2" command?

Yeah
info 2 displays results ok

Absolutely death?

I tried some new ROMs (by Tomal, luca16thebig, VNInt...) and after upgraging to Cotulla latest version Uni crashed!
Now it only can boot in to hard reset mode (LEFT softkey + RIGHT softkey + RESET), no another activity. PC can't recognize device.
I tried to disable USB connection in ActiveSync and used Multi TTY/ExitBT. These tools couldn't connect to device (mtty says "\\.\WCEUSBSH001 port can not open").
(Uni in that moment was in hard reset mode)
How can i repair device?

MaximKorobov said:
I tried some new ROMs (by Tomal, luca16thebig, VNInt...) and after upgraging to Cotulla latest version Uni crashed!
Now it only can boot in to hard reset mode (LEFT softkey + RIGHT softkey + RESET), no another activity. PC can't recognize device.
I tried to disable USB connection in ActiveSync and used Multi TTY/ExitBT. These tools couldn't connect to device (mtty says "\\.\WCEUSBSH001 port can not open").
(Uni in that moment was in hard reset mode)
How can i repair device?
Click to expand...
Click to collapse
Go into bootloader mode (on/off button, light button, and reset hole all at once) make sure your sd card is out, and try to flash again with cotulla rom! dont forget to read his instructions to go back to normal roms and allow time for rom to set up, dont hard reset after you flash!!!!
regards
Jay

Yep.
I move out SD (SDHC) and SIM cards.
Tried flash again - when PC program usually show previous version and new version right now it show empty fields. When it start to flash it show "Error 112: CE ROM UPDATE ERROR" message.

When my Uni is bricked I boot into the bootloader with the "Serial"-string. Then I put my SDHC out of the device and then it says "USB".
Every flash worked very well.

I can't force it to show "Serial"-string

Try this
Cotulla ROM is different.Memory allocation is different.
1.Remove SD card and always remove the SIM card.Very important.
2.First uncheck the 'allow USB connection' in active sync or WMDC[if VISTA].
Close active sync/WMDC in task manager.
3.Put Uni in BOOTLOADER.[Power+Backlight+Soft reset].
4.Run mtty.Click on USB.
5.Type 14 0 [ there is a single space between 14 and 0],press enter.
Wait ....
6.Type task 32 [there is a single space between task and 32],press enter
Wait....
7.Type task 28 55aa [ there is a single space between 28 and 55,and no space between 55 and aa],press enter
Wait...
8.When the desktop finishes the work..usually takes 5-10 seconds..close mtty.
9.Disconnect Uni...which is still in BOOTLOADER...
10.Go to active sync/WMDC and check 'allow USB connection'.
11.Flash with a WM5 ROM..I had KDSkamal's Ultimate ROM.
12.You should have got Uni back.
13.Then upgrade it to any ROM you want..6.0,6.1etc...if you want to.
Honestly speaking I don't know what the heck these procedures are,but if you do this STEP by STEP it works like a charm.
Cheers...waiting for your reply.

OK.
Now i know what to send Uni via mtty.
We have a solution to connect tools to device properly (mtty says "\\.\WCEUSBSH001 port can not open") after such crush?

MaximKorobov said:
Yep.
I move out SD (SDHC) and SIM cards.
Tried flash again - when PC program usually show previous version and new version right now it show empty fields. When it start to flash it show "Error 112: CE ROM UPDATE ERROR" message.
Click to expand...
Click to collapse
Will it go into boot loder mode??

Please give info
Okay.
So you mean your device is stuck in---
white screen
Splash image
Bootloader
Or what?
I just like to help out,I just read wiki.

responderman said:
Will it go into boot loder mode??
Click to expand...
Click to collapse
In to hard reset mode (LEFT softkey + RIGHT softkey + RESET) - yes.
In mode, when it show "Serial/USB" connection - not.
kalya said:
Okay.
So you mean your device is stuck in---
white screen
Splash image
Bootloader
Or what?
I just like to help out,I just read wiki.
Click to expand...
Click to collapse
Look (It can be shown only with USB connection):
http://picasaweb.google.ru/Maxim.Korobov/RepairOfHTCUniversal?feat=directlink
And nothing else

Well,at this stage,what happens when you press 0[zero]?
And can you please tell whether you can PUT the UNI in the BOOTLOADER by pressing POWER+BACKLIGHT+SOFT RESET simultaneously?
Because I have read almost all the threads regarding STUCK uni and I never came across one with a screen like yours.
On the second thought...press Backlight+Soft reset simultaneously...what do you see?

The image you are showing us is "Hard reset" what you want is bootloader. you get boot loader as we described above, once you have it in boot loader it is easy to get your uni back. In bootloader it will say serial or USB if it is plugged in at the top and V1.01 or V2.01 or something like those numbers at the bottom on a grey unlit screen.

kalya said:
Well,at this stage,what happens when you press 0[zero]?
And can you please tell whether you can PUT the UNI in the BOOTLOADER by pressing POWER+BACKLIGHT+SOFT RESET simultaneously?
Because I have read almost all the threads regarding STUCK uni and I never came across one with a screen like yours.
On the second thought...press Backlight+Soft reset simultaneously...what do you see?
Click to expand...
Click to collapse
1. If i press zero, Uni show "Cleaning now" message and after about 3 seconds turn off;
2. When i press POWER+BACKLIGHT+SOFT RESET there is no any results. What this keystrokes mean? I didn't know it before;
responderman i can't send command via mtty cause it don't wanna to open USB port.

Man,I am no techie,but really want to help you.
MaximKorobov said:
1. If i press zero, Uni show "Cleaning now" message and after about 3 seconds turn off;
Now,Forget mtty.
First PLEASE charge the battery 100%,use another unit if neccessary to charge.
You said When i press POWER+BACKLIGHT+SOFT RESET there is no any results. What this keystrokes mean? I didn't know it before
What do you mean by that.
1.You cannot enter the bootloader
or
2.You don't know what the bootloader is?
And did you uncheck usb connection in AS,remove SD and SIM during MTTY....just to be sure
And finally PLEASE read this thread...It is really helpful..though old.
http://forum.xda-developers.com/showthread.php?t=259003&highlight=universal+dead+stuck
Click to expand...
Click to collapse

"1.You cannot enter the bootloader"
But now... it's funny miracle.
I try POWER+BACKLIGHT+SOFT RESET again and it's go into bootloader (previously - no, just empty screen).
5 minutes and new rom installed successfull.
Thanks you guys!
It was very bad half week with a brick.

Well i'm glad we got there in the end. Can I recomend reading up in the WIKI to get to know things a bit better. Welcome to the forum

Glad to help!
Good to hear that.
And yes please search,read wiki,and please please name your threads in such a manner so people can understand what it's really about.
And I am glad this thread can be closed now.

Touch Screen not working, Tilt stuck even after flashing new ROM. Help Please!

Hello Friends,
I have been actively using Various ROMs in this section of the forum. I have flased almost each one of them and love them all.
I recently installed PDACorner ultimate v19 and it was working fine. I loved it.
However, today I faced strange problem. My touch screen stopped working. So I tried to realign it and it wasn't working at all. i could use the hardware buttons, but not the touch screen.
I did a hard reset and then my mobile stuck at the screen where it asks to "tap to continue".
and i could do nothing now.
Then i flashed the Simple OS to it and again the same problem. I dont know how to proceed now?
Is there any way to get through the initial touch screen condition which says "tap here to continue" ? My phone is within the warranty period but cant get it sent back due to unlocking thingy i did. Is reverting it back to the original condition possible without involving the touch screen ?
Please help me.

Thank parleyp for this.
http://forum.xda-developers.com/showpost.php?p=3435632&postcount=27
Should now be able to get back to a returnable state.

ceo.mtcl said:
Hello Friends,
I have been actively using Various ROMs in this section of the forum. I have flased almost each one of them and love them all.
I recently installed PDACorner ultimate v19 and it was working fine. I loved it.
However, today I faced strange problem. My touch screen stopped working. So I tried to realign it and it wasn't working at all. i could use the hardware buttons, but not the touch screen.
I did a hard reset and then my mobile stuck at the screen where it asks to "tap to continue".
and i could do nothing now.
Then i flashed the Simple OS to it and again the same problem. I dont know how to proceed now?
Is there any way to get through the initial touch screen condition which says "tap here to continue" ? My phone is within the warranty period but cant get it sent back due to unlocking thingy i did. Is reverting it back to the original condition possible without involving the touch screen ?
Please help me.
Click to expand...
Click to collapse
Yes you can revert without the touch screen..you can flash the stock rom via usb or sd card and then you can change to stock spl either via usb using sspl since you now know what to do to avoid the alignment screen or sd card using cmonex's tools.
FYI--welcome.not is the name you need to give to a blank file and put it on the root of the sd card. Make sure it has no extension.
I had to put mine back to stock without the usb cable since my usp port shorted last week.

Hello, my friend.
Sadly, my Kaiser has the same problem since past september, and then send it back to Houston, Tx for repair and they tell me the flash memory has ben corrupted, and just like you i try different ROM's and one day the touchscreen fail after used a Rom from ROMeOS. The only solution its change the mobo and then use an official ROM before flash a custom one.
Fortunately, Mr. Pedro Gonzalez (HTC Technical Support Manager), give me a hand and my phone was considered in warranty, so the repair was a kind present from HTC. Thank you again, Mr. Gonzalez !!!! My advice is if you still have warranty, use it.
Good luck with your Kaiser!!!
Sorry for my poor english.
Regards.

Thanks a lot
stylez said:
Thank parleyp for this.
http://forum.xda-developers.com/showpost.php?p=3435632&postcount=27
Should now be able to get back to a returnable state.
Click to expand...
Click to collapse
Thanks a lot... this trick worked for me!
Now i have to make my phone revert to the original situation so that it looks as if it came from the manufacturer.

Milmirex said:
Hello, my friend.
Sadly, my Kaiser has the same problem since past september, and then send it back to Houston, Tx for repair and they tell me the flash memory has ben corrupted, and just like you i try different ROM's and one day the touchscreen fail after used a Rom from ROMeOS. The only solution its change the mobo and then use an official ROM before flash a custom one.
Fortunately, Mr. Pedro Gonzalez (HTC Technical Support Manager), give me a hand and my phone was considered in warranty, so the repair was a kind present from HTC. Thank you again, Mr. Gonzalez !!!! My advice is if you still have warranty, use it.
Good luck with your Kaiser!!!
Sorry for my poor english.
Regards.
Click to expand...
Click to collapse
Thanks a lot mate for taking out time and sharing my tears. I returned from a toir today so i was unable to reply to my own thread. I will reinstall every thing back and if i get any problem then i will post back in this thread. Thanks a lot.
PS: English is just a medium o communication, and i completely understand you. If at all i do not understand you i will stop you and ask you what you are trying to say I am really glad that you replied to me. Thanks again.

parleyp said:
Yes you can revert without the touch screen..you can flash the stock rom via usb or sd card and then you can change to stock spl either via usb using sspl since you now know what to do to avoid the alignment screen or sd card using cmonex's tools.
FYI--welcome.not is the name you need to give to a blank file and put it on the root of the sd card. Make sure it has no extension.
I had to put mine back to stock without the usb cable since my usp port shorted last week.
Click to expand...
Click to collapse
Thanks a ton Parleyp for your support and making this forum richer. I will keep in touch with you coz i am fearing the fact that will my phone be completely reverted back to the original situation or not? I have to see the related thread for this and i will keep in touch.
Thanks for the helping hand.
Regards,
Teddy (Texas)

Reverted back to the locked State
I used the following thread:
Updated: Reverting back to the AT&T or HTC ROM and SPL for Warranty or return
and the Idiots guide to revert my phone back to the original state. I had to try JumpSPL1.93-KAIS.exe instead of the regular version.
I guess I am done with this part now.
Thanks a ton to you guys. Lets see what AT&T guys have to say about this?

A quick question...
parleyp said:
Yes you can revert without the touch screen..you can flash the stock rom via usb or sd card and then you can change to stock spl either via usb using sspl since you now know what to do to avoid the alignment screen or sd card using cmonex's tools.
FYI--welcome.not is the name you need to give to a blank file and put it on the root of the sd card. Make sure it has no extension.
I had to put mine back to stock without the usb cable since my usp port shorted last week.
Click to expand...
Click to collapse
Just a quick question? How do i make sure that my phone is locked and its now under warranty? Is there any software available that can provide us this information? I am sorry if it sounds like a noobs question but i really dont know how to check this before sending it back?

when your phone is off press the camera and the power button at the same time.
Make sure your phone doesnt say "Security Unlocked" at the top or at the bottom right corner it doesnt say Hard-SPL (insert number here) but that its says just "SPL (insert number here) "

kaiserII101 said:
when your phone is off press the camera and the power button at the same time.
Make sure your phone doesnt say "Security Unlocked" at the top or at the bottom right corner it doesnt say Hard-SPL (insert number here) but that its says just "SPL (insert number here) "
Click to expand...
Click to collapse
Thanks a lot for the reply but I think that i am missing something... I did the following:
1. Turned off the phone.
2. Pressed the camera button and held it there while i pressed the power button (holding both buttons).
But the device started as usual. And i could not see the any such display. The display was the same as if i would have pressed just the power button. Is it possible for you to provide a screen shot of this?

My bad!
Whoopss! I tried it again, and i got the tri color screen which says following three lines in the red strip:
KAIS1*0
SPL-1.56.0000
CPLD-8
and following word in the white strip:
Serial
I hope it is fine now?

I got my new Tilt
I got MY new Tilt!
I am Happy

welcome.not
just simply create a 'welcome.not' file on windows open notepad then save it w/out content filename welcome.not make sure that the extention in not welcome.not.txt otherwise it wont work...put the file to sd card root then hard reset by pressing the power button for 10 second then boot again after about 5-10 seconds for safety....gudluck hope this could help you!!