Database Info

Advanced Shelltool help

Hi everyone. I am in need of assistance with shelltool. I've been flashing ROMs for quite some time and this goes beyond the scope of typical upgrading. I apparently had a bad flash happen and need some help correcting it. The OS appears to work fine, except some applications .cab installers exit before asking device or storage card. I have attempted to load the EnableRapi.cab and Cert_SPCS.cab; however, they exit almost instantly after starting them.
I had this situation happen once before and I was able to oddly enough try to load the original T-Moblie ROM through shelltool (didn't install at all), then try NBD 8.3. which brought me to a boot loader screen after doing a hard reset, but didn't install NBD 8.3. So far I'm not having much luck in recreating the experiment.
Is there a way to force a Wizard into bootloader mode using shelltool or some other utility? I can restore the device if I can get that far.

it's time for my first post
Hi, have been reading this forum for about 3 month and i enyoy it and learn a lot. Have been try about 7 roms and like all. It's time to payback.
Yo can enter bootload by pressing and holding the voice command button and then softreset, keep holding the voice command button util you reach bootload.
Other thing you can do is run the original rom by its executable program not using shelltool.
Good luck

Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!

Dezl0ck said:
Awesome! That rescued my phone. You saved me quite a bit of time in getting my phone back to a working state. You've more than given back!
Click to expand...
Click to collapse
no problem, that's why we are here for, to help each other

Help, Stuck at multicolor screen. XDA Mini S
Dezl0ck said:
I can restore the device if I can get that far.
Click to expand...
Click to collapse
Please tell me how did you restore your phone? i am flashed touchflo rom to my phone and some how it is stuck to the multicolor screen.
Can you help me out?
Thanking you in anticipation.

1 put phone into bootloader by pressing and holding camera button+reset hole. Keep holding the camera button untill you see the tricollor screen.
2 plug the phone into the computer (wait to hear the noise that it found hardware
3 Flash a rom you know worked (maybe your original/ maybe someone elses... maybe even mine )
4 wait untill the flashing finishes and "Tap Screen..." appeares before unplugging.
(If you have a G4 then I advise you to flash the original rom, or make sure your ipl/spl is propper. check the G4 forum to be sure, or ask Mestrini - The creator of the Wizard service tool. I believe he has a G4 and knows more about it than most)
Happy Flashing

Randomly get Update/Connection errors.
Thank you very much for the response.
Unfortunately, i am still not able to flash the ROM. I did the follwoing steps, can you please help me letting me know, where m i wrong?
I restarted my PC.
I did Reset my PDA, by removing and placing the battery.
then i boot the PDA, it always boots to the TRICOLOR Screen.
afterwards, i tried to flash following ROMs
Xda_Minis_Upgrade_v2.21.4.101.exe [the oringal one, used to be working since long]
SNN_Version_3.0 [i flashed this, some days ago and worked fine for me]
SNN_3.0_FULL_version [the ROM that caused the problem]
BUT no use, i randomly get following errors:
ERROR [262] : UPDATE ERROR
ERROR [274] : CONNECTION
and some other errors.
Pleaaaaaase some one help me.
Thanking you in anticipation.

I've read a ton here but still have one question!

I want to start out by saying I'm really sorry if I'm asking something stupid but I am a complete newbie and do intend to learn as much of this on my own as I can....
I took my brand new AT&T Tilt and I connected it to my Vista Laptop when it was charged fully and used the built-in Windows Mobile Device Center to do a quick connect (like a guest connect where files can be transferred but stuff isn't synched) and ran kaiser_HardSPL which gave me a white screen rather than the expected tri-color screen.
I found the solution for the white screen and did a reset by pushing the stylus into the small hole space on the bottom of the Tilt and then connected it again to my laptop and copied over JumpSPL1.56-KAIS to the phone. I then ran that app from the phone and the tri-color screen showed up. When 'USB' showed up on the screen I disconnected the USB cable for about 10 seconds and plugged it back in. The text 'USB' stayed on the screen and nothing happened after that. I then used the stylus again to reset the PDA again and I am now at my current step.
Am I ready to put a ROM on now? I'm so new to this and I definitely want to learn just not sure what's next....is my CID unlocked? Did everything go correctly or did I miss out on some important step?
What should I do next if I want to put a new ROM on? Whatever help anyone can give me would be very much appreciated.
Looking forward to becoming an active and contributing member to this great community!

Gas Addict said:
I want to start out by saying I'm really sorry if I'm asking something stupid but I am a complete newbie and do intend to learn as much of this on my own as I can....
I took my brand new AT&T Tilt and I connected it to my Vista Laptop when it was charged fully and used the built-in Windows Mobile Device Center to do a quick connect (like a guest connect where files can be transferred but stuff isn't synched) and ran kaiser_HardSPL which gave me a white screen rather than the expected tri-color screen.
I found the solution for the white screen and did a reset by pushing the stylus into the small hole space on the bottom of the Tilt and then connected it again to my laptop and copied over JumpSPL1.56-KAIS to the phone. I then ran that app from the phone and the tri-color screen showed up. When 'USB' showed up on the screen I disconnected the USB cable for about 10 seconds and plugged it back in. The text 'USB' stayed on the screen and nothing happened after that. I then used the stylus again to reset the PDA again and I am now at my current step.
Am I ready to put a ROM on now? I'm so new to this and I definitely want to learn just not sure what's next....is my CID unlocked? Did everything go correctly or did I miss out on some important step?
What should I do next if I want to put a new ROM on? Whatever help anyone can give me would be very much appreciated.
Looking forward to becoming an active and contributing member to this great community!
Click to expand...
Click to collapse
Quick question, and I'm not trying to be funny or anything, but did u read?

Thanks for the quick reply -- I did read the different threads that I thought would be dealing with this but was unsure of what to do after I did the white screen fix. The white screen fix said there was a way to test if it worked by checking a splash screen but when I ran that it said make sure you've already done HardSPL first otherwise it can brick your phone so I wasn't sure if I did actually do that step properly or not (of installing HardSPL).
I'd appreciate any help you could give me. Thank you again for taking the time to read my post!

Bronx31 said:
Quick question, and I'm not trying to be funny or anything, but did u read?
Click to expand...
Click to collapse
I can answer that!

I apologize for missing something obvious -- could anyone please point me to which thread I should look at?
Thank you.

No your device is still not ready.
http://forum.xda-developers.com/showthread.php?t=354061

You're on the right track. From what I gather you can indeed flash something at that stage on SSPL or continue on to flash HardSPL (which is what I believe you intended to do!). Get back to the stage you were at and, from the thread in which you found JumpSPL, flash HardSPL onto your phone. After that point you are totally ready to become a slave to dutty's roms...
Look here and ye shall find: HardSPL will not install - WHITE SCREEN: SOLVED

Well, first correctly install HardSPL, then go on flashing a ROM. You may find my FAQ usable. See my signature.

Nono... one more step to go.
After disconnect and connect usb flash hardspl then softreset.
bmueller77 said:
Well, if you correctly installed HardSPL which sounds like this, go on flashing a ROM. You may find my FAQ usable. See my signature.
Click to expand...
Click to collapse

Laurentius26 said:
Nono... one more step to go.
After disconnect and connect usb flash hardspl then softreset.
Click to expand...
Click to collapse
Already corrected it. But you were faster ^^

Thank you to all of you -- you're all being very helpful!
I ran the flash-hardSPL (ran the file in that folder called KaiserCustomRUU) and it gets all the way to where it is updating the rom image to the kaiser-hardSPL version and it shows 0% on my phone and 0% on the PC and after about a minute or so it says ERROR [262] : UPDATE ERROR ... it instructs me to remove my battery for 3 seconds, put it back in and try again.
I've done this twice now and keep getting the same error -- any ideas on what I'm doing wrong?
Thank you once again.

The only thing I can think about is that your phone is simlocked.
Do you have the usb cable connected straight to the pc or do you use a usbhub?
Gas Addict said:
Thank you to all of you -- you're all being very helpful!
I ran the flash-hardSPL (ran the file in that folder called KaiserCustomRUU) and it gets all the way to where it is updating the rom image to the kaiser-hardSPL version and it shows 0% on my phone and 0% on the PC and after about a minute or so it says ERROR [262] : UPDATE ERROR ... it instructs me to remove my battery for 3 seconds, put it back in and try again.
I've done this twice now and keep getting the same error -- any ideas on what I'm doing wrong?
Thank you once again.
Click to expand...
Click to collapse

Oh yes, that's true. I didn't realize I had to unlock my phone before I could start this process...I guess I confused it with CID unlocking or something.
I must have missed the part in the newbie FAQ about phones needing to be sim unlocked for all this stuff to work.
I guess I will have to get it unlocked first! Very much appreciate the prompt replies.

oh i just realized my SIM wasn't even in the phone while I was doing this (since I took it out during the white screen fix) -- would putting the SIM back in still create the same problem if my phone isn't unlocked?

Laurentius26 said:
The only thing I can think about is that your phone is simlocked.
Click to expand...
Click to collapse
You mean CID-locked, right?
Perhaps you could try another CustomRUU. Check this one http://forum.xda-developers.com/showthread.php?t=334890

Gas Addict said:
Oh yes, that's true. I didn't realize I had to unlock my phone before I could start this process...I guess I confused it with CID unlocking or something.
I must have missed the part in the newbie FAQ about phones needing to be sim unlocked for all this stuff to work.
I guess I will have to get it unlocked first! Very much appreciate the prompt replies.
Click to expand...
Click to collapse
No, a SIM-lock does not affect flashing.

So you ran JumpSPL from your phone, saw USB displayed on the screen, unplugged the usb cable, replaced it and then ran the hardspl provided from the thread I linked you to? There is no soft resetting going on between seeing USB on the screen and initiating the hardspl flash.

arexben said:
So you ran JumpSPL from your phone, saw USB displayed on the screen, unplugged the usb cable, replaced it and then ran the hardspl provided from the thread I linked you to? There is no soft resetting going on between seeing USB on the screen and initiating the hardspl flash.
Click to expand...
Click to collapse
Hi arexben,
I actually was an idiot and soft reset after unplugging and then plugging in the USB and not seeing any change on the screen.
Now if I put JumpSPL on my PDA and try to run it, it won't run saying it can't be opened because its either not signed w/ a trusted certificate or one of its components cannot be found.
Thank you so much for everyone trying to help me ... so to clarify, my phone has not been unlocked from AT&T and I am assuming I should still be able to get this stuff working.
Thanks again!

Gas Addict said:
Hi arexben,
I actually was an idiot and soft reset after unplugging and then plugging in the USB and not seeing any change on the screen.
Now if I put JumpSPL on my PDA and try to run it, it won't run saying it can't be opened because its either not signed w/ a trusted certificate or one of its components cannot be found.
Thank you so much for everyone trying to help me ... so to clarify, my phone has not been unlocked from AT&T and I am assuming I should still be able to get this stuff working.
Thanks again!
Click to expand...
Click to collapse
Not sure, but try to install the sdkcerts first.
Download them here: http://www.cinetsystems.com/xda/Kaiser Cab Collections/SdkCerts.cab

bmueller77 said:
Not sure, but try to install the sdkcerts first.
Download them here: http://www.cinetsystems.com/xda/Kaiser Cab Collections/SdkCerts.cab
Click to expand...
Click to collapse
Installed the SdkCerts then tried running JumpSPL off the phone still can't run that program.
Any other ideas guys?
Thank you again!

Help!! Can I Revive My Tornado!!!

Hi. Can someone please help me out? I was trying to flash my cingualr 2125 from wm 5.0 to 6.0. I was using Kar Hoe's instuctions and I used the typhoon instuctions instead of the tornado instuctions. I didn't know there was a difference at the time.
I did all the steps up until step 5 on the typhoons where it states you will get a white screen. At that point, I accidently hit my usb and the phone disconnected from active sync. I thought if I took my battery out, I could just do a reboot and get the reboot screen. Well I got nothing. I cannot even turn the phone one. I cannot even connect to active sync. I thought maybe I fried the battery and bought a new one and no luck. I have done a hard restart and all other things that I could think of.
Does anyone know if I had hurt the phone and if it can be fixed to get to the bootable screen. I would be happy just to get it to power on and stay with wm5 just to have the phone working.
I really appreciate your help.
Khernden69

Aah i remember doing the same once i screwed up my newly acquired tornado with typhone rom. phone was dead no bootup screen nothing, i tried every thing asked everywhere, thankfully i had warranty period so went to them with very innocent face and made up a story that "i switched it at night and it wont boot in the morning" they bought and gave me a new phone after a week. any ways GOOd Luck

Enjoy WM6

think your in trouble mate. Using the wrong rom and cancelling it half way is a big no no. Least you have a fancy paper weight

Similar problem
I have just acquired a tornado (in it's o2 guise) and it will only get as far as the wm splash screen. I thought trying a hard reset or flashing it with a new rom might revive it. However I tried hard reset (holding down the 2 soft keys beneath screen while pressing power button?) but it just kept booting to the splashscreen. The phone doesn't boot far enough to be recognised by Activesync so can't flash it. Can anyone suggest a solution? Would going to bootloader mode allow me to flash it? If so, how do I do that?
Thanks

try this.
1.switch off phone
2. remove battery
3. re install battery
4. hold camera button
5. while holding camera button plug usb cable to port
6. after some second u will see three color bootloder screen
7.format binfs
7. then u can flash correct tornado rom
you can us alternative method for going to bootloder mode
hold camera button while holding camera button press power button(not hold)
GOOD LUCK

Hi fayizk1
Thanks for the tip. Just one question, will this command CID unlock the phone too? It's just the phone isn't CID unlocked, I've tried using instructions and tools on other threads to change the CID value of downloaded roms to that of my phone, but all Typhoonnbftools produces is a 512 byte .nbf file which isn't good for anything. Any suggestions?

binfs not allowed!
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?

First off, try a couple different times. The "format BINFS" command is case sensitive - where your capital letters are makes ALL the difference. You may need to try a couple times, but I believe "format" is all lowercase and "BINFS" is all capitals.

Thanks djsleepwalker but I tried your suggestion and tried a few times in different cases but still got "Not allowed operation". (If all caps I get "Invalid command") I read somewhere that I'm getting this message because the phone is not CID-unlocked?

Tried a few times in different cases, still get "Not allowed operation". I read somewhere else that I'm getting this message because the phone is not CID-unlocked? Well I know that otherwise I would have just flashed another rom. Problem is I have tried using Typhoonnbftools to change the CID over numerous roms, the file it produces is only 1kb or smaller which is no good for anything. I feel like I'm running out of options...

Just try to flash with a legal WM5 ROM from the magnufacture's web site while the device is in bootloader screen. I hope it will work.
Good luck

This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.

Won't help
timwb said:
This is my problem. There isn't one on their site! I emailed them but they were no help at all.
edit: Have also searched loads of forums etc. no-one seems to have it and there are lots of people looking for o2 roms.
Click to expand...
Click to collapse
Well, I found 'magic' WM5 for SDA, but since it CIM locked, and upgraded to radio 2.0, phone refuse to upgrade (downgrade) to WM5, he said I needed newer file or something... It's stucked in bootloader

I come from China IOICN, but I can not help you, because my bad English.

timwb said:
When I run format binfs from teratermpro I'm told it's not allowed. What do I do now?
Click to expand...
Click to collapse
try first
info 2
then
format BINFS

Still says "Not allowed operation!"

timwb said:
Still says "Not allowed operation!"
Click to expand...
Click to collapse
can you get any information when you try "info 2" command?

Yeah
info 2 displays results ok

I've RESEARCHED, and found no answers. I think it's bricked

Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.

barrnunn said:
Hello to all, I am a noob here and have tried to adhere to all of the demands to do research and not post ?'s, but I am at a wall.
I have a Tilt and I ran the sim unlock and I was using the Sleuth 3.0 on it. Everything was working fine. I added the Iunlock cab and it worked fine as well. I then tried to install the icontacts, but i would have to go to program files and icontacts file in order to use I contacts. Well, wanna be innovative me thinks to try and move that file so it would replace something. I copied it to the windows appbuttons folder and deleted the regular contacts and nothing happened, then I put it in the start up folder and no luck, then I simply copied it to the windows folder not at the bottom where all of the extra files are. After that I tried to reset it and now all that I get is the bootloader screen. it reads as follows:
KAIS1*0 MFG
SPL-1.0.Olipof
CPLD-8
At the bottom, it shows either USB or Serial depending on if the usb is plugges up.
I tried running the sim unlock again and the dutty rom and both load to 100% but it goes back to the same screen. Any help would be greatly appreciated. Please help and thank you so much.
Click to expand...
Click to collapse
You could hard reset if you altered something in WM to cause it not to boot...hopefully

I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?

barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
Yeah and then you press send...
- well you could try go into the bootloader and flash an OEM original ROM on i do not believe that doing this would brick your kaiser.

zeezee said:
You could hard reset if you altered something in WM to cause it not to boot...hopefully
Click to expand...
Click to collapse
In case u dont know how to do it:
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets

Or else search for MTTY. That helped a lot of ppl who got stuck in boot loader.

barrnunn said:
I tried the hard reset and same thing I flashes for a very split second loading and then goes back to the screen.
Hard reset is both item buttons above IE and Mail with soft reset correct?
Click to expand...
Click to collapse
U need to hold the stylus in the hole longer, untl a message pops up on the page.
If it does not hardreset or help u, do what zeezee told u - flash a new rom.

OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.

barrnunn said:
OK, thank you all for you diligent assistance. I have tried the hard reset and it does the same thing...goes to black for about 2 seconds, then for a very split second goes to a grey screen and flashes loading then back to the bootloader.
I will try a search for the people stuck in bootloader and try flashing a OEM ROM, I will let you know how it goes. Thanks again.
Click to expand...
Click to collapse
Here is a list of OEM ROMs:http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs

I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!

Before you try the dangerous MTTY method, you could try refresh a oem rom w/ the SD method

ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?

barrnunn said:
ok, I am flashing an OEM rom now, but what does it mean to do it with the sd method?
Click to expand...
Click to collapse
From youre sd card (memorycard), look it up in wiki. Moust of us flashaholics keeps oure rom on oure memorycard and just rename the rom/bootsplash/radio or whateva and place it in root then activate bootloader -> flash. This is an alternative for not using usb cable, pc and active sync
http://wiki.xda-developers.com/index.php?pagename=KaiserSDFlash

ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.

barrnunn said:
ok thanks, but am i correct in understanding that to do that I have to use the phone to access the mem card?
My issue is that the only screen I get is bootloader, no nothing else. I can't even turn it off. I can take the battery out to get a black screen, but any action to try something will take it back to the bootloader screen. But for some reason, it still allows me to flash the ROM, I think. I flash it on my pc and then my phone goes to the grey screen where it shows the % of progress. It reaches 100% and the pc tells me to click finished and I do then it goes back to the bootloader.
Click to expand...
Click to collapse
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.

thesire said:
put the rom image file on storage card and than power on phone in bootloader. the process will start automatically.
Click to expand...
Click to collapse
yes, just use a card adapter or something to acess youre card (if you cant connect via active sync) then copy the rom over and follow the steps in wiki. Beeing stuck in the bootloader some times aint the worse place to be stuck

korakesion said:
I do not see any Mods here around or somebody yelling (search button is your friend,search the wiki everything is there, bla bla)To having a woman at home change everything.. Thanks..!
Click to expand...
Click to collapse
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos

tvos said:
I don't mean to argue with you here and you are right about research threads, but honestly it's easy to get caught up in frustration with the amount of information. Some authors are good at documentation and some skip steps along the way or extra links are in the threads.
I just switched over to Gullum's Diamond Rom and was I nervous upgrading "Yes" and did I read much that I could "Yes". Were the instructions to HardSPL, Jump were a little unclear "Yes" so people asking questions are legit to a degree but we shouldn't also be eagar to pounce on...
tvos
Click to expand...
Click to collapse
I agree with some of your remarks. Yes myself and others have jumped down people's throats yelling, "Search." One thing you have to remember though this is a developers forum, not a novice forum to help people making there phone look "cool."
Going into flashing / upgrading / modifying, you have to have a little bit of knowledge or time using Windows Mobile / Windows in General devices and machines.
Usually reading some background information can be a world a difference before jumping into this sort of thing.

I found the problem to stuck in bootloader. Thanks to all who have posted threads.
Originally Posted by GSLEON3
Many of you have noticed that in the past I spent a great deal of time helping people with Kaiser issues. Many of you have asked for help in the last few days & are probably feeling ignored. I am just unavailable at this time. My little sister had a Kidney Transplant operation on June 30th, 2008 & I have been spending much time traveling back & forth between my home in California & her's in Arizona. There were a few complications, but she is now doing well & recovering. I will be spending this weekend & most of next week helping to care for her & will be unavailable still for the next ten days or so.
There are many capable people in the Kaiser forum that will help. If you have hit a wall, be patient & I will begin to answer my PM's in the order they were recieved within the next week. Sorry I can't be of more help at the moment, but family comes first as I'm sure you understand.
Thanks,
GSLEON3
Aboslutely man. You go take care of your family. I will pray for God to guide you all through this trying time.
On the Kaiser note, I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.

Solution for Those Stuck in Bootloader
Here is the link to the initial thread I started for my issue
http://forum.xda-developers.com/showthread.php?t=406221
I found after further studying of some threads, a solution to my issue where I was stuck in bootloader. I think this will apply to anyone that is stuck in bootloader with the usb/serial showing at the bottom and when they try to flash a new rom is goes to 100%, but the are still stuck on the boot screen.
After reading more threads, it appeared that there was some sort of disconnect between the usb and the phone. Since my PC was stating that it was successfully completing the flash, that shows that it was not getting any type of error from the phone. After reading a thread I simply blew in my tilt usb port and used my stylus to try to straighten it out as one of your post state to ensure the usb connection is straightor it may give mtty an issue.
Once I messed with my USB port, the phone came back to life and everything was fine. Everything was rebooted and all my info was lost however. I was even able to successfully flash a new ROM.
In closing, if anyone is stuck in bootloader mode and their flash goes to 100% and doesn't fix their issue, tell them to clean and straighten their usb connection.

Can you Unbrick a Touch Pro 2?

Hey guys looks like a bricked my 2 week old Sprint Touch Pro 2. I can't get pass the touch pro 2 logo screen now and I'm very upset with myself. Is there a way to possible unbrick the phone. I tried to sync it with my PC no response. Also i did back it up with " Microsoft My Phone " earlier in the day and its backed up on WMDManager too. I will try to take it to sprint for warranty and see what the will do. HAPPY NEW YEAR people!!

clariceave said:
Hey guys looks like a bricked my 2 week old Sprint Touch Pro 2. I can't get pass the touch pro 2 logo screen now and I'm very upset with myself. Is there a way to possible unbrick the phone. I tried to sync it with my PC no response. Also i did back it up with " Microsoft My Phone " earlier in the day and its backed up on WMDManager too. I will try to take it to sprint for warranty and see what the will do. HAPPY NEW YEAR people!!
Click to expand...
Click to collapse
Depending on what happened, it's a yes/no situation. What did you do?
Try this:
get into bootloader mode (tri-color screen): Take out the battery for one minute. Put it back in. Getting into bootloader mode is done by holding the Volume down button while you do a press/release of the Reset button. OR hold the Volume down button while you do a press/release of the Power button.
That should get you to bootloader mode. Now, plug in your USB to the PC. Flash a CDMA ROM from there by running the .exe. If you cannot do that, transfer the .nbh file (rename it to "RHODIMG.nbh" [no quotes]) and follow these instructions.
Good luck, and happy new year!
*The majority of the CDMA ROMs can be found at PPCGeeks*

PLEASE HELP ME UNBRICK MY TOUCH PRO 2 (tmobile)
i was installing a ROM onto my TP2 but i accidentally installed a CDMA ROM instead of a GSM ROM. My phone loads past the TP2 startup screen but then stays white with the rom info on the bottom. I tried to do the bootlegger with the 4 colors on the screen but it doesnt work. Also tried a hard reset. CAN SOMEONE PLS PLS PLS HELP? thanks

foxxyroxy5 said:
i was installing a ROM onto my TP2 but i accidentally installed a CDMA ROM instead of a GSM ROM. My phone loads past the TP2 startup screen but then stays white with the rom info on the bottom. I tried to do the bootlegger with the 4 colors on the screen but it doesnt work. Also tried a hard reset. CAN SOMEONE PLS PLS PLS HELP? thanks
Click to expand...
Click to collapse
Well, this forum is for CDMA TP2s, but I'll help.
So you took out the battery for at least one minute? Then you put it back in. Get into bootloader mode (T-Mobile version: phone is off, hold the Volume Down button while you press/release the Power Button. Keep holding the Volume Down button until the colorful screen shows up).
When you're in bootloader, plug in your TP2 to your PC. Now run the .exe of a GSM ROM and follow the steps, as if your phone is synced to the PC. (aka flash as you would usually do).
To flash via the Storage Card: On your PC, go to Start > My Computer > Removable Disk drive (something like that; make sure this is your phone's Storage Card). Drag the .nbh of a GSM ROM there. Rename the .nbh "RHODIMG.nbh" (no quotes). Unplug your Phone. Take out the battery again for one minute. Now, go back into bootloader (hold Volume Down button and press/release Power button [keep holding the Volume Down button]). Follow the steps to flash the phone.
Good luck.

RE:LEASE HELP ME UNBRICK MY TOUCH PRO 2 (tmobile)
Thank you very much for helping me with my TP2 problem! You were my last resort and i was going to give up. It works perfectly fine! I really really appreciate it! THANK YOU AGAIN

Should work
foxxyroxy5 said:
i was installing a ROM onto my TP2 but i accidentally installed a CDMA ROM instead of a GSM ROM. My phone loads past the TP2 startup screen but then stays white with the rom info on the bottom. I tried to do the bootlegger with the 4 colors on the screen but it doesnt work. Also tried a hard reset. CAN SOMEONE PLS PLS PLS HELP? thanks
Click to expand...
Click to collapse
You did exactly the reverse of what I did, and the instructions already given are how I resolved it: put it in bootloader and flash a compatible ROM. I flashed a stock ROM just to be sure, but that's probably not needed.

foxxyroxy5 said:
Thank you very much for helping me with my TP2 problem! You were my last resort and i was going to give up. It works perfectly fine! I really really appreciate it! THANK YOU AGAIN
Click to expand...
Click to collapse
No problem. Enjoy your unbricked TP2 this new year!

Bricked my Sprint Touch Pro 2
i downloaded a hotfix for internal gps from htc website for Sprint touch pro 2. after i tried to install it the phone went off and now it won't even power on or go to boot loader.. any suggestions on how i can fix this i was using Mighty Rom 6.5 with htc sense 2.1

[email protected] said:
i downloaded a hotfix for internal gps from htc website for Sprint touch pro 2. after i tried to install it the phone went off and now it won't even power on or go to boot loader.. any suggestions on how i can fix this i was using Mighty Rom 6.5 with htc sense 2.1
Click to expand...
Click to collapse
See if you can do a hard-reset right now. While phone is off (which it is), press and hold Talk/Send, End, and Power button at the same time. Wait for a screen to pop-up. Follow steps to hard reset. That will bring it back to factory defaults.
If it doesn't work, maybe you could post your question on PPCGeeks, where a lot of CDMA people go. They might be able to help you.

Can you Unbrick a Touch Pro 2
Hi to all,
I'm a new here and a little desperate . I flashed my rom by using a raphael update instead of Rhodium. My phone got bricked. My phone is a Sprint HTC touch pro 2.
At the moment, it will not boot, when I plug it to my computer and it was looking for qualcomm cdma MSM drivers.
I tried sof and hardware reset including the boot loader. Nothing works. I also tried using different RUUs. Nothing works. I hope somebody can help me.

Fixed the problem...bought an android...ha,ha...

smileyzst said:
The same exact thing happened to my tp2.Accidently flashed touch pro(RAPHEL)rom and now nothing!!It won't power on or anything,can someone help me too...Is my phone bricked???? Help please!!!
Click to expand...
Click to collapse
Well if you can power it on, and go to bootloader, then your phone is just fine. Just flash a Rhodium ROM.
I suggest take battery out, and put it back in after few seconds, to see if it powers on. If not, leave it in the charger, and see if it powers on.

After installing the HardSPL, I decided to flash my US Cellular CDMA phone with a GSM rom and of course it bricked it. The phone would only boot to bootloader, so I was going to have it repaired for $70. But if I was willing to flash my device, then I'm sure as willing to look for a DIY solution somewhere. Goodthing I searched this forum, because the answers where right here!
Just format your microSD to FAT32, install an extracted stock ROM kit to the root of the SD insuring you rename the .nbh to RHODMIG.nbh and place the other extracted files on the SD as well. Place the microSD in your HTC Touch Pro2 and boot to bootloader. You may have to take steps to get to the bootloader, mine booted to bootloader automatically anyway at that point. Follow onscreen instructions, and your Touch will be as good as new!

thanks a million for helping me unbrick my tp2
wow man thanks a million, i followed the instru and it worked but was slow so i did task 29 and flashed the rom i wanted and it works great, i really appreciate your help on this

How did you get to the bootloader menu. I am using CDMA HTC Pro 2 by Sprint. Thanks
goldenu said:
You did exactly the reverse of what I did, and the instructions already given are how I resolved it: put it in bootloader and flash a compatible ROM. I flashed a stock ROM just to be sure, but that's probably not needed.
Click to expand...
Click to collapse

@rocco24
Did everything go alright? If not, just post here or send me a PM.

Hi i have a different issue I accidentally flashed the wrong nv items 01192 and now its rebooting. if someone can dump their tp2 sprint 6.5 nv items please help. I am cut off from the world of cell phones at the time. I read that i also would need the radio dump which in my case is the same one on the 6.5 ruu windows version. any feed back or advice is welcome. please help guys.
Oscar

sumflipnol said:
Well, this forum is for CDMA TP2s, but I'll help.
So you took out the battery for at least one minute? Then you put it back in. Get into bootloader mode (T-Mobile version: phone is off, hold the Volume Down button while you press/release the Power Button. Keep holding the Volume Down button until the colorful screen shows up).
When you're in bootloader, plug in your TP2 to your PC. Now run the .exe of a GSM ROM and follow the steps, as if your phone is synced to the PC. (aka flash as you would usually do).
To flash via the Storage Card: On your PC, go to Start > My Computer > Removable Disk drive (something like that; make sure this is your phone's Storage Card). Drag the .nbh of a GSM ROM there. Rename the .nbh "RHODIMG.nbh" (no quotes). Unplug your Phone. Take out the battery again for one minute. Now, go back into bootloader (hold Volume Down button and press/release Power button [keep holding the Volume Down button]). Follow the steps to flash the phone.
Good luck.
Click to expand...
Click to collapse
I wonder if you can help me; i have a sprint hybrid cdma/gsm and it has black screen no lights at all but the qualcomm cpu is easily recognized by pc-have tried all known methods to get in bootloader but i get no lights at all??-have fully charged batt from another tp2=any experience w this problem?-thanks

keeps rebooting?
Hello, I'm wondering if anyone has experienced the problem I'm facing:
I have the latest Energy rom, with Android 2.3 on SD card. Android proved to be quite unstable and requires soft resets every now and then. Most of the time I would let it boot into WinMo and then run Haret again to get into Android.
Yesterday I left in running in Android all day, and in the evening I noticed the phone had died. Thinking it was just out of battery, I just plugged it in, let it charge for a few hours, then tried to boot it up. But it just kept rebooting, never getting pass the Touch Pro 2 boot screen.
Did hard resets twice, same thing. Re-flash the rom, same thing. Took out SD card, flashed again, same thing. Everything I tried, it would not get pass the initial boot screen, and just cycles the reboot again. Oh by the way, the hard resets and re-flashes are all successful with no errors.
Anyone have a solution to this? Thanks!

velo25 said:
Hello, I'm wondering if anyone has experienced the problem I'm facing:
I have the latest Energy rom, with Android 2.3 on SD card. Android proved to be quite unstable and requires soft resets every now and then. Most of the time I would let it boot into WinMo and then run Haret again to get into Android.
Yesterday I left in running in Android all day, and in the evening I noticed the phone had died. Thinking it was just out of battery, I just plugged it in, let it charge for a few hours, then tried to boot it up. But it just kept rebooting, never getting pass the Touch Pro 2 boot screen.
Did hard resets twice, same thing. Re-flash the rom, same thing. Took out SD card, flashed again, same thing. Everything I tried, it would not get pass the initial boot screen, and just cycles the reboot again. Oh by the way, the hard resets and re-flashes are all successful with no errors.
Anyone have a solution to this? Thanks!
Click to expand...
Click to collapse
Try flashing another ROM or try putting in another battery and see if the bootloop issue goes away. Kindly update the status of your post if you fixed the issue or are still having problems.