I'm having a lot of trouble with my android. I fell asleep on the couch around half an hour ago and I woke up, and it was dead, so I put it on the charger. But the screen flashed this cyan screen saying broken cable. I put it on every single charger in the house and still nothing worked. I even put other phones and tablet on these chargers to make sure they worked and they did. So I don't know why my phone isn't charging. Whenever I do put it on a charger it just turns in but is an all black screen then immediately turns off. It keep doing this and I'm scared it'll mess up my phone. I noticed in the top corner it said "(timeout) Normal booting" so I'm wondering what is going on and what can I do to fix it. Is this one of those red rings of death moments or am I just exaggerating???
Which phone is it?
Related
After my issues with my One X, my daughter looks to have bricked her One S after dropping her phone in the sink....
Early on Saturday morning my daughter ran through shouting that her One S had just fallen from her pocket and landed in the sink. It was in the water just a second or two. She brought it straight through to me and it was working fine, but the phone was on a constant vibrate. I pulled the sim, and removed the top and bottom cover, and got the hairdryer out. I dried it on cold for 30 minutes (no heat at all) and put it straight in a sealed tupperware box of rice in the boiler cupboard. I had expected to pull it out this lunch time (a full 48 hours later) expecting it to be fine, but after plugging it in to charge on the mains for 4 hours, it wont boot.
At the moment it flashes green and red when on charge, but this disappears when it is removed from charge. This is the same whether it is charged via USB or mains.
When I first tried to start it up, the screen flashed around a third of the way down and the nothing.
Second attempt, I held down the lock button and held it. After a few seconds the three buttons at the bottom flashed 15 (I counted them) times and then nothing.
Third time, as above, but flashed 5 times.
Since then nothing. No flashing, no noise, blank screen.
Incidentally, when it seemed to want to boot it never vibrated (if that helps the diagnosis?)
I haven't got the tools, so I had planned to pick some up tomorrow and order a replacement battery from Ebay. My reasoning is because I have read that the lights I have flashing relate to battery issues.
Any other options? Is there any hope for this phone now?
AW: Water damaged - now flashing green and orange. Wont turn on.
Does it geht recognized when you plug it into you computer?
OK I don't know of it even gets recognized if its turned off, bit its worth a try.
Sent from Space
chouman said:
After my issues with my One X, my daughter looks to have bricked her One S after dropping her phone in the sink....
Early on Saturday morning my daughter ran through shouting that her One S had just fallen from her pocket and landed in the sink. It was in the water just a second or two. She brought it straight through to me and it was working fine, but the phone was on a constant vibrate. I pulled the sim, and removed the top and bottom cover, and got the hairdryer out. I dried it on cold for 30 minutes (no heat at all) and put it straight in a sealed tupperware box of rice in the boiler cupboard. I had expected to pull it out this lunch time (a full 48 hours later) expecting it to be fine, but after plugging it in to charge on the mains for 4 hours, it wont boot.
At the moment it flashes green and red when on charge, but this disappears when it is removed from charge. This is the same whether it is charged via USB or mains.
When I first tried to start it up, the screen flashed around a third of the way down and the nothing.
Second attempt, I held down the lock button and held it. After a few seconds the three buttons at the bottom flashed 15 (I counted them) times and then nothing.
Third time, as above, but flashed 5 times.
Since then nothing. No flashing, no noise, blank screen.
Incidentally, when it seemed to want to boot it never vibrated (if that helps the diagnosis?)
I haven't got the tools, so I had planned to pick some up tomorrow and order a replacement battery from Ebay. My reasoning is because I have read that the lights I have flashing relate to battery issues.
Any other options? Is there any hope for this phone now?
Click to expand...
Click to collapse
It could be that the device has 0% battery.
Try to plug it in the charger and hold the power button for so 15 min.
Then try constantly to turn on(plluged im the charger)
This should help
Sent from my Sony Xperia Z
No no no don't plug it in! There's likely still water in there that could short the circuits and permanently damage the phone, if it hasn't happened already. Power it off fully, put it in rice or some sort of dessicant, and let it sit for at least a week. The longer you wait, the better chance you have of saving it.
Thanks guys for the quick replies.
The phone won't connect to my laptop or computer and won't let me access HTC Sync. The 3 lights at the bottom will only flash when the phone is plugged in, if I unplug it won't do anything at all.
I can't see there being any liquid left in there at all. It was thoroughly dried with a cool hair dryer (and worked perfectly) before I shut it down manually and placed it in the rice for 2 days. I think that I'm at the stage where I can be confident of that.
Sounds like a dead battery to me.. But just to be safe wait a while before charging it
chouman said:
After my issues with my One X, my daughter looks to have bricked her One S after dropping her phone in the sink....
Early on Saturday morning my daughter ran through shouting that her One S had just fallen from her pocket and landed in the sink. It was in the water just a second or two. She brought it straight through to me and it was working fine, but the phone was on a constant vibrate. I pulled the sim, and removed the top and bottom cover, and got the hairdryer out. I dried it on cold for 30 minutes (no heat at all) and put it straight in a sealed tupperware box of rice in the boiler cupboard. I had expected to pull it out this lunch time (a full 48 hours later) expecting it to be fine, but after plugging it in to charge on the mains for 4 hours, it wont boot.
At the moment it flashes green and red when on charge, but this disappears when it is removed from charge. This is the same whether it is charged via USB or mains.
When I first tried to start it up, the screen flashed around a third of the way down and the nothing.
Second attempt, I held down the lock button and held it. After a few seconds the three buttons at the bottom flashed 15 (I counted them) times and then nothing.
Third time, as above, but flashed 5 times.
Since then nothing. No flashing, no noise, blank screen.
Incidentally, when it seemed to want to boot it never vibrated (if that helps the diagnosis?)
I haven't got the tools, so I had planned to pick some up tomorrow and order a replacement battery from Ebay. My reasoning is because I have read that the lights I have flashing relate to battery issues.
Any other options? Is there any hope for this phone now?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=27101970
Take the phone to a sevice they will disamble and dry properly , probably they will use tehnical alcool and clean all your el. contacts and dry it with hot air. Good luck
Sent from my HTC Desire S using xda app-developers app
Update:
I was ready to bleach the water marker and/or get some phone insurance, but when I went back to the phone a couple of days after my last post, I plugged it in to charge again and when I checked it a couple of hours later it was working.
it's well over a week later, and there are no obvious I'll effects now.
I'm really surprised, but obviously delighted.
Hi I need help with trying to repair my sensation z710e.
I had to replace the digitizer today. I followed a couple of guides i found online. I was very careful and gentle throughout the procedure. Unfortunately I did break a cable which lights up the bottom row of buttons. It was glued solidly to the digitizer but even as i scraped at it as gently as I could it snapped. Okay , not the end of the world. I was warned about it in the guide but it was just glued to solidly.
Anyway put everything back together and got a boot loop when i turned on. I rebotted into the bootloader to see what would happen, that worked fine but when I selected recovery the thing just froze and rebooted and continued to boot loop.
I then tried to re-flash the radio file PG58IMG.img but wasn't allowed to as the phone reported that the batter was too low.
So i plugged it in and left it there for an hour or two switched off.
But the current situation now is that the phone won't turn on at all. When the charger is plugged in the orange LED is on but flashes to Off for a second every 10 seconds. Does anyone know if this is a code for something.
It looks to me that the battery died and didn't charge at all when I plugged it in earlier. Could that be due to bricked firmware? I have no way of telling if the battery is actually dead as I don't have the equipment to test. I have a feeling I can save this phone somehow. Any ideas anyone? Thanks.
ezzony said:
Hi I need help with trying to repair my sensation z710e.
I had to replace the digitizer today. I followed a couple of guides i found online. I was very careful and gentle throughout the procedure. Unfortunately I did break a cable which lights up the bottom row of buttons. It was glued solidly to the digitizer but even as i scraped at it as gently as I could it snapped. Okay , not the end of the world. I was warned about it in the guide but it was just glued to solidly.
Anyway put everything back together and got a boot loop when i turned on. I rebotted into the bootloader to see what would happen, that worked fine but when I selected recovery the thing just froze and rebooted and continued to boot loop.
I then tried to re-flash the radio file PG58IMG.img but wasn't allowed to as the phone reported that the batter was too low.
So i plugged it in and left it there for an hour or two switched off.
But the current situation now is that the phone won't turn on at all. When the charger is plugged in the orange LED is on but flashes to Off for a second every 10 seconds. Does anyone know if this is a code for something.
It looks to me that the battery died and didn't charge at all when I plugged it in earlier. Could that be due to bricked firmware? I have no way of telling if the battery is actually dead as I don't have the equipment to test. I have a feeling I can save this phone somehow. Any ideas anyone? Thanks.
Click to expand...
Click to collapse
The orange blinks mean that your battery is drained to the fullest. So you need to recharge it. Plug the phone in a 'wall charger' not computer or ps3 whatever just straight from the wall charger keep im mind it could take an hour to recover but when it happened to me it took 30 mins to get enough juice to power on
EDIT:
Alternative if the charging doesnt work.
http://forum.xda-developers.com/showthread.php?t=1198585
Sent from my HTC (Quietly Brillia... bad at updating their phones) Sensation.
SPAM DAT THANKS BUTTON?
So I Dropped My Moto G in water, I immediately turned it off and shoved in a bag o' rice for approximately 2 Hours, and being the impatient person I am I took it out :silly: and started using it. This is where the problems began to show. I would press the power button and the screen would turn off and then it would just turn back on. Whatever, big deal, I thought but I was wrong. Then the screen stopped turning on. Well, maybe it died. So I plugged it in and the notification light went blinking on and off. Then I tried to turn it on again and it did not work. Well $hit, I thought there goes my phone. So I stuffed back in the bag of rice and left it there for a week and a half and when I plug it in to charge it, the blinking blinked on and off (which indicates it charging) and it still doesn't turn on. So I try Holding the Power+Volume Down and the blinking stopped, but then 10 seconds later it resumed.
So my question is : what parts should I purchase to fix this phone?
P.S. The screen is cracked but it worked before the incident
I recently dropped my phone on the ground and the glass is now broken. But it worked normally for about 14 days. Then suddenly one day at work it shut down on its own. After that I wasn't able to start it. No reaction for any of the buttons, nor their combinations. Even when I plugged the charger in, no sign of life. I thought it's over.
Then the next day, I plugged the charger in and the screen with 0% battery appeared. So I left it charging, but when I came back to it (20 minutes) it was dead again. Not even the diode indicating it is charging. Again no response for the buttons, nothing. So I tried to disassemble it, disconnected everything. Put it together and viola! The screen indicating 0% battery was there again. I left it like that for a while, and when it was charged a little, I tried to start it. It started and normally worked. At least it seemed to, but after a while (1 - 3 minutes) while I was using it, it went to the dead phone again.
So I discovered, that when I disconnect the battery for a while and then connect it again, I am able to boot the phone. I was even able to do factory reset. I thought I got it and that it was some software fault. However after like 5 minutes (it downloaded all apps, logged to my google account, looked all ok) the screen shut down again and again the phone played dead.
Now I have the phone booted, and charging (almost 100% now). But I guess when I start using it again, it will again go to the dead mode (since it did it everytime after I used it a little, no specific action done, totally random).
I guess it has to be related to the broken glass. Maybe some water or humidity got through it and the phone is trying to save itself from damage by going to the dead mode. It's weird because sometimes (like now) the phone is OK when not used, normally chraging and not shutting down (now it's ON for about 40 minutes), but if it shuts down, it takes about 3 or 4 battery disconnect and connect again, before it boots to the main screen. Sometimes it just dies before the screen, sometimes it dies when I try to plug the charger in, really no idea what causes it.
How should I diagnose it? USB debugging and check the log when using it and when it dies? Or has anyone experienced this too? Or could the battery be damaged? Or can I somewhere set the phone to prevent from selfkilling actions? Today I will try my main board in my friends G Flex 2, to see if it's the board, or something else.
Error log from console before it shut down
mazlixek said:
I recently dropped my phone on the ground and the glass is now broken. But it worked normally for about 14 days. Then suddenly one day at work it shut down on its own. After that I wasn't able to start it. No reaction for any of the buttons, nor their combinations. Even when I plugged the charger in, no sign of life. I thought it's over.
Then the next day, I plugged the charger in and the screen with 0% battery appeared. So I left it charging, but when I came back to it (20 minutes) it was dead again. Not even the diode indicating it is charging. Again no response for the buttons, nothing. So I tried to disassemble it, disconnected everything. Put it together and viola! The screen indicating 0% battery was there again. I left it like that for a while, and when it was charged a little, I tried to start it. It started and normally worked. At least it seemed to, but after a while (1 - 3 minutes) while I was using it, it went to the dead phone again.
So I discovered, that when I disconnect the battery for a while and then connect it again, I am able to boot the phone. I was even able to do factory reset. I thought I got it and that it was some software fault. However after like 5 minutes (it downloaded all apps, logged to my google account, looked all ok) the screen shut down again and again the phone played dead.
Now I have the phone booted, and charging (almost 100% now). But I guess when I start using it again, it will again go to the dead mode (since it did it everytime after I used it a little, no specific action done, totally random).
I guess it has to be related to the broken glass. Maybe some water or humidity got through it and the phone is trying to save itself from damage by going to the dead mode. It's weird because sometimes (like now) the phone is OK when not used, normally chraging and not shutting down (now it's ON for about 40 minutes), but if it shuts down, it takes about 3 or 4 battery disconnect and connect again, before it boots to the main screen. Sometimes it just dies before the screen, sometimes it dies when I try to plug the charger in, really no idea what causes it.
How should I diagnose it? USB debugging and check the log when using it and when it dies? Or has anyone experienced this too? Or could the battery be damaged? Or can I somewhere set the phone to prevent from selfkilling actions? Today I will try my main board in my friends G Flex 2, to see if it's the board, or something else.
Click to expand...
Click to collapse
Adding the error log from console
OK so it was probably mother board fault, so I had to buy a new phone It is like 3 months, and I just yesterday accidentally poured some water on it, so i destroyed another one. It is still in warranty but I guess with water damage there is no warranty. Anyone knows where to find all the water damage indicators? Or is it even possible to make it look like there was no water damage?
Hey guys,
a few days ago I accidentally dropped an HTC One E8 in water and obviously it doesn't work anymore. Before buying a new one I wanted to ask, if some of our "HTC experts" may have suggestions on what else I could try before giving up.
The situation: I dropped it in water, didn't turn it off (dumb, I know) and it worked for around 10 minutes until it powered off. I left it in rice for a day and it didn't turn on or charge. At this point I nearly gave up.
I left it for in rice (about 48 hours) and - the orange led was flashing while charging. Even the screen turned on and it showed a charging symbol first and after a few seconds it showed a red circle and a white exclamation mark. After some time I could power it on and the touchscreen worked and I could use it, but it still was around 1%/0%. The screen flickered, but it was usable. I wanted to plug it in my computer then to rescue some data, but 5 seconds after I took it off power (to switch from the wall charger to my PC) it died.
Now I tried it to power it on for like 2 days, but with no charger connected nothing happens and when I connect the charger, the orange led is on constantly. I tried power/volume- and power/volume+, but nothing happens. Not even the charging indicator comes up, the screen is completely dead.
Are there any steps to try before giving up? By the way I don't want to disassemble it
Thanks in advance