Hello everyone,
I need some help with the following situation:
Using Odin I successfully flashed my Galaxy A32 5G with Android 13 (as indicated by the green PASS in Odin).
When the phone tries to reboot, I get the dreaded error message, "Can't load Android system. Your data may be corrupt....."
On my PC I issued the command, >adb devices, but no devices were found.
This is probably because I did not enable USB debugging, when the phone was still working.
I'm trying to avoid doing a factory reset, because I don't want all my data wiped.
According to the following article, you can flash an OTA file using "adb sideload" command, even without enabling USB debugging.
However, everything else I've read says that adb commands work only when USB debugging is enabled.
Fix “Can’t Load Android System Your Data May Be Corrupt” Without Resethttps://www.droidwin.com/fix-cant-load-android-system-your-data-may-be-corrupt-without-reset/
Can someone perhaps clarify whether or not USB debugging is required for using adb commands?
Thank you very much,
Peter
plee12 said:
Hello everyone,
I need some help with the following situation:
Using Odin I successfully flashed my Galaxy A32 5G with Android 13 (as indicated by the green PASS in Odin).
When the phone tries to reboot, I get the dreaded error message, "Can't load Android system. Your data may be corrupt....."
On my PC I issued the command, >adb devices, but no devices were found.
This is probably because I did not enable USB debugging, when the phone was still working.
I'm trying to avoid doing a factory reset, because I don't want all my data wiped.
According to the following article, you can flash an OTA file using "adb sideload" command, even without enabling USB debugging.
However, everything else I've read says that adb commands work only when USB debugging is enabled.
Fix “Can’t Load Android System Your Data May Be Corrupt” Without Resethttps://www.droidwin.com/fix-cant-load-android-system-your-data-may-be-corrupt-without-reset/
Can someone perhaps clarify whether or not USB debugging is required for using adb commands?
Thank you very much,
Peter
Click to expand...
Click to collapse
I think, In stock recovery only the adb sideload command works so it don't need USB Debugging to be turned ON.
aiSanaul said:
I think, In stock recovery only the adb sideload command works so it don't need USB Debugging to be turned ON.
Click to expand...
Click to collapse
Thanks for your input. Encouraged by your input, I read the article again and realized that I have to put the phone in sideload mode first.
So, I went back to the stock recovery mode and selected the menu item, "Apply update from ADB". Then I see the message on the phone, "Now send the package you want to apply....with adb sideload <filename>". Now that I thought the phone was in sideload mode, on the PC I entered ">adb devices". This time it recognized the device and displayed the device name. However, it also displayed the word, "unauthorized", after the device name. According to the article, if sideload is properly entered, it should display the word, "sideload".
Anyway I tried entering ">adb sideload update.zip", and I got the error message, "device unauthorized".
So, any idea how to get the phone to be authorized?
If this is not possible, I was thinking of replacing the stock recovery with a custom recovery like TWRP. This way I can at least back up all my data first before doing a factory reset. However, I believe installing TWRP requires the bootloader to be unlocked, which automatically wipes all data. So, this defeats the purpose of installing TWRP in the first place
Is there some trick to install TWRP without unlocking the bootloader?
Thank you
plee12 said:
Thanks for your input. Encouraged by your input, I read the article again and realized that I have to put the phone in sideload mode first.
So, I went back to the stock recovery mode and selected the menu item, "Apply update from ADB". Then I see the message on the phone, "Now send the package you want to apply....with adb sideload <filename>". Now that I thought the phone was in sideload mode, on the PC I entered ">adb devices". This time it recognized the device and displayed the device name. However, it also displayed the word, "unauthorized", after the device name. According to the article, if sideload is properly entered, it should display the word, "sideload".
Anyway I tried entering ">adb sideload update.zip", and I got the error message, "device unauthorized".
So, any idea how to get the phone to be authorized?
If this is not possible, I was thinking of replacing the stock recovery with a custom recovery like TWRP. This way I can at least back up all my data first before doing a factory reset. However, I believe installing TWRP requires the bootloader to be unlocked, which automatically wipes all data. So, this defeats the purpose of installing TWRP in the first place
Is there some trick to install TWRP without unlocking the bootloader?
Thank you
Click to expand...
Click to collapse
As you already know this is not possible without unlocking bootloader, I will explain further more to make it easy to understand.
If you don't unlock your bootloader and try flashing TWRP on your phone using ODIN Flash Tool then maybe your phone get into an veification error and your phone will end up in a softbrick. You can repair your phone by flashing your phone's stock firmware using ODIN Flash Tool, eventually you will wnd up loosing all your data.
Also unlocking bootloader in Samsung devices is so easy by turning OEM Unlocking in Developer options, but you don't seem to have access to your phone.
An Unlocked Bootloader is the PASS, which allows you to do custom thing to your phone. So without it, this won't work, maybe that is why you got that error “Can’t Load Android System Your Data May Be Corrupt”.
ALTERNATIVELY you can try flashing your phone's OLD original Stock Firmware using ODIN Flash Tool and see what happens. You can also try flashing TWRP through ODIN Flash Tool. Only flash OFFICIAL TWRP made for your device (if any), otherwise you don't have options I guess.
also Why didn't you Unlocked Bootloader before flashing a custom rom? because of warranty?
aiSanaul said:
As you already know this is not possible without unlocking bootloader, I will explain further more to make it easy to understand.
If you don't unlock your bootloader and try flashing TWRP on your phone using ODIN Flash Tool then maybe your phone get into an veification error and your phone will end up in a softbrick. You can repair your phone by flashing your phone's stock firmware using ODIN Flash Tool, eventually you will wnd up loosing all your data.
Also unlocking bootloader in Samsung devices is so easy by turning OEM Unlocking in Developer options, but you don't seem to have access to your phone.
An Unlocked Bootloader is the PASS, which allows you to do custom thing to your phone. So without it, this won't work, maybe that is why you got that error “Can’t Load Android System Your Data May Be Corrupt”.
ALTERNATIVELY you can try flashing your phone's OLD original Stock Firmware using ODIN Flash Tool and see what happens. You can also try flashing TWRP through ODIN Flash Tool. Only flash OFFICIAL TWRP made for your device (if any), otherwise you don't have options I guess.
also Why didn't you Unlocked Bootloader before flashing a custom rom? because of warranty?
Click to expand...
Click to collapse
Thanks very much for your detailed explanations and for your continued support.
Let me answer your question first about why I didn't unlock the bootloader before flashing a custom ROM. Let me backtrack and explain how this problem came about in the first place. My phone was doing an automatic system update two weeks ago (Android 13). After downloading and installing, it tried to boot up. That's when it got stuck in an infinite rebooting loop. At that point, I had no way to change any settings on the phone.
Also, to clear up any confusion, I was not trying to flash a custom ROM. I was simply trying to flash the stock ROM (Android 13), supposedly the same firmware version as the OTA that broke my phone after the automatic system update. I was thinking that perhaps there was an internet glitch during the automatic system update process, which corrupted the OS. So, I was just trying to re-install the same version as the OTA to see if that would solve the problem.
I had also thought about flashing the original version that came with the device (Android 11). But, I think I read somewhere that either Samsung phones do not allow the user to downgrade, or even if it does allow you do so, the downgrading process will wipe out the existing data on the phone. Perhaps you can confirm that or not?
In the meantime, as you suggested, I will look into how to flash TWRP.
Thank you
Related
I've spent lots of time looking through forums trying to answer/solve my issue so I hope it's not something stupid I've missed. Sorry for the trouble if it is though.
So, my issue is that I simply cannot unlock the bootloader of my Nexus S (i9020T). The phone's connecting to my computer via Samsung Android ADB Interface as seen under the Device Manager. I see the proper device ID when I type "fastboot devices" into the adb command prompt w/ phone in fastboot mode. Then, when I type "fastboot oem unlock" the phone starts the unlock verification process -- I select yes, the phone restarts, but it goes back to the stuck Google screen. Then, if I pull the battery and go into fastboot mode directly, bootloader's still locked. I've tried this quite a few times and same result -- same result trying to unlock w/ some of the toolkits here (WugFresh's NRT, m.sabra's root tool). Haven't tried Odin but from what I've read it would also require an unlocked bootloader to do anything. I've even tried a few other things like pushing recovery and bootloader images onto the phone via adb, but these also failed due to the locked bootloader.
I also cannot enable USB debugging under phone settings either b/c I now can't get past the Google logo/fastboot mode menu. Didn't think this was required to unlock bootloader though.
Background: Phone had the latest auto updated version of Android when the phone all of a sudden turned off in the middle of the night recently. Weird b/c the battery was basically full. It now always gets stuck on the Google logo upon normal restart. It goes into fastboot mode OK if I remove the battery and press power/vol. buttons -- I then first tried the restore and recovery functions there, etc, but no effect.
Any ideas? Or is the phone just dead now?
Thanks! :fingers-crossed:
Edit:
I've now tried what's described as a possible solution here: http://forum.xda-developers.com/showthread.php?p=44753413#post44753413. It didn't work since that also needs bootloader to be unlocked.
I've also tried to solve it w/ all versions of Odin. None of them detect my phone even after installing Kies w/ drivers. I think I have the required drivers though since I can command the phone fine through adb. And Odin should need bootloader unlocked to work anyway...
Edit 2:
To add, one of the first things I tried was to do a manual factory data reset in the recovery menu (selecting 'yes' to erase all data).
And I tried adb sideload of the OTA .zip file. But installation was aborted. The following appeared immediately under the regular adb sideload instruction in the system recovery menu (under "Now send the package you want to apply to the device..."):
Finding update package...
Opening update package...
Verifying update package...
Installing update...
file_getprop: failed to stat "/system/build.prop": No such file or directory
Installation aborted.
Bump w/ more info.
I just tried rooting my phone. The phone is cycling back and forth between the bootloader is unlocked screen and the Motorola splash screen.
To repeat some steps from a prior post.
My phone had QPR30.80-58-3 .
I downloaded that ROM and extracted the boot.img file.
I downloaded the latest Magisk Manager and installed it on my phone.
I ran through the patching process for boot.img.
I requested an unlock code from Motorola and unlocked the bootloader.
I flashed the patched boot image which patched partition b.
I flashed the patched boot image to partition a.
I rebooted which began the cycle.
I tried holding down the power button but it returns to the cycle.
I can get back to the bootloader with the Volume Down and Power buttons.
Any suggestions on what could get me back to a functioning phone, rooted or not rooted?
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
dafunk60 said:
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
Click to expand...
Click to collapse
I checked that the image I patched was from the QPR30.80-58-3 ROM which matched the level after the phone was updated.
I flashed that original boot image which flashed partition a and then rebooted. I did not flash partition b.
It first came up with the unlock warning screen. It sat on the Motorola splash screen for a noticeable amount of time followed by a yellow screen with a circle around the Motorola symbol. Finally it ended up on a blue Hello there screen with a yellow start button.
This screen was unresponsive. Eventually through various cyclings through all this I ended up on a screen that said Android could not boot and gave me an option of a factory reset. I did that but it did not help getting past the Hi there screen.
I went back and flashed the QPR30.80_58 image on both partitions a and b. This got me back to setting up the phone again. The phone is at QPR30.80_58. I am considering just rooting at this level.
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
DougPeterson said:
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
Click to expand...
Click to collapse
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
dafunk60 said:
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
Click to expand...
Click to collapse
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If you want to get into recovery, boot into the bootloader than do
Code:
fastboot reboot fastboot
That'll boot you into fastbootd which has an option to go to the real recovery
DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If adb isn't showing any devices connected that would explain why the rescue software cannot find your phone. Perhaps you don't have the correct driver installed. Windows Device Manager shows the phone as a Motorola ADB Device on my PC.
View attachment 5061327
Another possibility is that you have multiple versions of adb on your PC. Older versions won't work but the adb.exe in "C:\Program Files (x86)\Rescue and Smart Assistant" works for sure. With your phone booted into android & unlocked, plug it into your PC. Do you see the "USB debugging connected" on the phone? If you don't I would re-check that USB debugging is enabled. If you do see the debugging notification, on your PC, open a command prompt and navigate to "C:\Program Files (x86)\Rescue and Smart Assistant". Run
Code:
adb devices
Does adb find your phone?
I went through the process of using Smali and Magisk on my phone. Everything was good. Since I was doing this for PoGo, I decided to "clean-up" by disabling some of the settings. I turned off OEM unlocking, reboot the phone in to the bootloader and did a adb flashing lock. I rebooted the phone and not get the error "Can't find a valid operating system". I can boot in to the bootloader with the power button + down volume but I can't unlock the bootloader with ADB and fastboot.
Am I screwed?
I'm also not able to boot in to recovery. I also get the error "Can't find valid operation system"
Well probably too late to reply.
I'm not an expert, i'm newbee but when i installed my custom rom i met some problems to reboot. I solved them by re-installing firm operating system. You can do it by connecting your device with a good usb cable and go to google website : android flash tool
This will reinstall a new an clean system (but erase your data if not saved before).
After that you can install a custom rom from the begining.
Hi! My old phone is booting into fastboot mode, when I try to boot normally I get a black screen, the "Power off" button appears when I hold the power button. The bootloader is not unlocked and the phone was never rooted. Wiping the user partition does not help. It is visible in fastboot mode and I can enter stock recovery, though trying to adb sideload a stock rom returns an error (footer is wrong; signature verification failed). Trying to fastboot boot twrp or recovery.img doesn't work either. I've ran out of ideas, what should I do to get this phone to work?
Try flashing the stock ROM with fastboot. I'm pretty sure ADB doesn't let you flash onto your phone because using your phone with ADB means that it's still powered on - which can cause some issues. You can also try and unlock your bootloader through fastboot, and then flash a recovery and custom ROM.
Both failed. I attached the errors I recieved.
crepper4454 said:
Both failed. I attached the errors I recieved.
Click to expand...
Click to collapse
Try "fastboot bootloader unlock", maybe. Also: Is there a flashall.bat in the stock ROM folder? If there is: Connect your device while in fastboot, and double-click it.
crepper4454 said:
Both failed. I attached the errors I recieved.
Click to expand...
Click to collapse
Try this maybe. I know you can't wipe through the stock ROM, so, try the command: "fastboot -w". That'll wipe everything off the device.
[INDEX][Osprey][Merlin] Moto G Factory Firmware Images
Disclaimer: I am not responsible for anything that happens as a result of flashing these files. Your destiny is your own. Moto G (3rd Gen) Factory Firmware Images - Provided by Firmware TEAM - Please report broken links. New Mirrors welcome...
forum.xda-developers.com
I can wipe through stock recovery. I did fastboot -w and it cleared the cache and userdata partitions, they were already clean afaik. Typing fastboot bootloader unlock returns unknown command. There are no .bat files in my firmware. I can try downloading one from the site you linked, but I don't know what to do with it if fastboot flash does not work.
crepper4454 said:
I can wipe through stock recovery. I did fastboot -w and it cleared the cache and userdata partitions, they were already clean afaik. Typing fastboot bootloader unlock returns unknown command. There are no .bat files in my firmware. I can try downloading one from the site you linked, but I don't know what to do with it if fastboot flash does not work.
Click to expand...
Click to collapse
Try this: https://forum.xda-developers.com/t/guide-osprey-fastboot-flashing-factory-firmware-images.3187750/
It says there that the "preflash validation failed" error occurs when the firmware being flashed is older than the one already installed. I will try downloading a newer version and flashing it. Will update here.
Update: I have dowloaded a newer rom and tried to flash it. This time got different errors (picture attached, this went for every sparsechunk). I think I know the reason but I do not know how to solve it. This might not be the exact stock rom of this phone so I cannot flash it with a locked bootloader. Could someone help me finding the correct rom or suggest a different solution?
Yooooo. I have the Moto e5 Cruise and so does my wife. We bought them in 2018 from Cricket and last night hers went to emmc failure, also known scientifically as 'no worky' mode.
The phone would only load in fastboot and had tried to use my Moto RSD tool to reflash but the phone would not detect in anything but fastboot mode.. Here's where it gets interesting....
There is a piece of software called the Lenovo (which now owns Moto) Rescue and Smart Assistant that can reflash your phone back to factory, no matter your sub-variant (cricket, metro, etc). Without having a fresh backup on hand, you're going to be beholden to the last cloud sync or manual backup you have because all data will be wiped in the below process.
BTW: Just run the assistant as it seems to be the easiest 'back-to-stock/working' tool I can find. Going to fastboot alone yielded weird errors since i didn't have the unlock code for the 'fastboot oem unlock [code goes here]' command.
**RESTORATION PROCESS**
This will apply to multiple Lenovo/Moto Mobility devices. Unknown at this time how many have been impacted by this seemingly pre-planned failure on Lenovo's part.
If your phone is stuck in fastboot mode where MTK download mode does not load, nor does adb, follow these simple steps:
(NOTE: BACKUP YOUR FILES IF POSSIBLE)
1. Click the link above to be directed to the Lenovo software download page and run the installer on your PC (Sorry Mac users :'().
2. The software, once installed, will require you to sign up for OR link a google, fb, g+, etc account to it for purposes of creating a Lenovo ID. Once signed in, click on 'Rescue Now'.
3. With your phone in fastboot mode, allow the software to download the firmware for your phone.
4. Once the firmware has finished downloading and validating, click on 'Rescue Now' once again. Your phone will begin the reflashing process.
That... actually worked. The program found the required ROM and flashing went without problems. Thank you very much @kmt5150 .
crepper4454 said:
That... actually worked. The program found the required ROM and flashing went without problems. Thank you very much @kmt5150 .
Click to expand...
Click to collapse
No problemo! Glad it worked!
I'm trying to install lineage OS 16 on my Sony Xperia Tablet Z LTE, in order for it to be up to date and able to use modern apps. I'm really not that tech savvy, but this far I've managed to unlock the bootloader, root the device and I believe I've managed to flash the recovery drive with the TWRP file meant for my device. I tried to flash the recovery from my windows PC, but every time I received "Failed "remote command not allowed" despite the device being unlocked at the bootloader and it is an A partition. So instead I went ahead and rooted the device and afterward flashed the tablet from the official TWRP app. At the end of the flash, I got "Flash completed successfully" which leads me to believe that I've flashed it correctly.
Now the issue is that no matter what I try, I can't boot into recovery mode. Every time I try, it just boots up regularly. I've tried via ADB terminal, through the TWRP app, and physically with the power button+volume down button, but everytime I get the same result.
This has me wondering, could I just download the Lineage image to my device and flash it directly to the boot partition or would this not work? Also what could be the reason I can't boot into recovery mode?
Sorry if this is not the forum for this topic, i just can't imagine who else would be able to advise me on this
luka0954 said:
I'm trying to install lineage OS 16 on my Sony Xperia Tablet Z LTE, in order for it to be up to date and able to use modern apps. I'm really not that tech savvy, but this far I've managed to unlock the bootloader, root the device and I believe I've managed to flash the recovery drive with the TWRP file meant for my device. I tried to flash the recovery from my windows PC, but every time I received "Failed "remote command not allowed" despite the device being unlocked at the bootloader and it is an A partition. So instead I went ahead and rooted the device and afterward flashed the tablet from the official TWRP app. At the end of the flash, I got "Flash completed successfully" which leads me to believe that I've flashed it correctly.
Now the issue is that no matter what I try, I can't boot into recovery mode. Every time I try, it just boots up regularly. I've tried via ADB terminal, through the TWRP app, and physically with the power button+volume down button, but everytime I get the same result.
This has me wondering, could I just download the Lineage image to my device and flash it directly to the boot partition or would this not work? Also what could be the reason I can't boot into recovery mode?
Sorry if this is not the forum for this topic, i just can't imagine who else would be able to advise me on this
Click to expand...
Click to collapse
Just to be sure, do you have USB debugging enabled?
Droidriven said:
Just to be sure, do you have USB debugging enabled?
Click to expand...
Click to collapse
I do, and of course I went and enabled it again after I bootloaded the device
Droidriven said:
Just to be sure, do you have USB debugging enabled?
Click to expand...
Click to collapse
You said you tried volume down+power, on most devices, that is the combination to boot into bootloader mode, fastboot mode or download mode, depending on the device. Volume up+power is generally the combination to boot into recovery mode. This doesn't seem to be your issue though. Are you sure you flashed TWRP to the correct partition? If your device is an A/B partitioned device, you may have flashed to one of these partitions when you needed to flash to the other partition.
Try flashing a copy of your stock recovery then see if that repairs the recovery partition and allows stock recovery to boot. If it works correctly after flashing stock recovery, you may not be flashing TWRP correctly or the actual flash might be being blocked by something that you're overlooking. Are you certain that your bootloader is unlocked?