Hello. I have a Poco x3 Pro. It is bricked, it has a restart loop. It can be enter the fastboot mode.
But it has no bootloader unlock, it is locked. My USB debugging is not opened. What can I do to unbrick it?
Thanks.
mertkont said:
Hello. I have a Poco x3 Pro. It is bricked, it has a restart loop. It can be enter the fastboot mode.
But it has no bootloader unlock, it is locked. My USB debugging is not opened. What can I do to unbrick it?
Thanks.
Click to expand...
Click to collapse
Find Official Xiaomi/Redmi/Poco repair center or customer service.
Related
My device is bricked !
Hi Guys,
If bootloader is locked, turned off the USB debugging, and device is bricked, it's stopped at logo. What can I do ?!
Venting said:
Hi Guys,
If bootloader is locked, turned off the USB debugging, and device is bricked, it's stopped at logo. What can I do ?!
Click to expand...
Click to collapse
What firmware are you on? Turning off usb debugging doesn't brick anything. What did you do to get to where you are now? Give some details.
Venting said:
Hi Guys,
If bootloader is locked, turned off the USB debugging, and device is bricked, it's stopped at logo. What can I do ?!
Click to expand...
Click to collapse
Hi there, you should download smart switch and use emergency firmware recovery, From there you should click 'more' then click emergency software recovery. Key in your device SM-G920F (Or whatever your version is) then input your serial number (Found on your device Box/back panel of your phone) then voila, it should download the latest firmware for you. Remember to boot into download mode
Hello everyone! I brought a Lenovo Vibe X3 (x3a40) 3 months ago. And I updated it to MM 6.0.1 and the bootloader was unlocked and the device was rooted. TWRP was also installed. So I installed this CyanogenMod 13 from HERE.
Then I missed some stock features and decided to revert back to stock MM. And I used QFIL to flash the official stock ROM. But it turned out that QFIL suddenly stopped working and my device got stuck in EDL mode. Once I turned it off completely to flash it again, the device wouldn't boot up. In my case the device should get into EDL when I connect the USB cable and immediately hold the power key for a second. But there is no response.
Usually while booting the device vibrates but now there is no vibration nor is there anything on the display. The screen keeps completely off and it wouldn't boot into any mode, like no download/no recovery/no EDL/no bootloop, just cold.
And when I connect it to the USB all I get is the "Device not recognized" error. In device manager I get this "Unknown USB device (Device Descriptor Request Failed)".
Please note that I've tried switching the USB cable and the port as well as on a different PC and also checked with the drivers. Still the same. If someone could help me, it would be a great help.... :crying:
Further info on the device is here!
After an update my phone is stuck in bootloop. Phone is neither rooted , USB debugging mode is off. Just like a new phone. It's a 64gb version. Anyonecan provide any steps how to unlock bootloader or any solution for my problem.
What Update?
I'm stuck in the fastboot loop. After I unlocked the bootloader I got factory reset and I forgot to enable USB debugging which I believe caused the issue. Recovery doesn't work and MSM tools do not work. Tried a lot of button combinations to get into EDL with no luck, I'm guessing it doesn't work because it's not hard bricked? I'm not seeing the qualcomm drivers in device manager.
Turns out the "genuine OEM" cable I bought from ebay was the problem, now I can get into EDL mode and use msmtool
Hey guys, i´m trying to access my phone via EDL mode.
I am able to enable the EDL Mode by shorting the board pins, the COM Port is correct (Qualcomm HS-USB QDLoader 9800), but the phone wont turn on when in EDL mode, i dont know if this is correct or not. It boots ok in normal mode.
I cant find a programmer either, i could find "prog_emmc_firehose_Sdm660" but i think the Note 6 Pro is "Sdm 636", not sure.
Any help?
Thanks