Install twice custom recovery on samsung galaxy A10 - General Topics

First of all sorry for my bad english.... i want to install custom recovery on samsung a10 me install orangefox recovery but it say fail to flash zip or cant read internel storage etc..... so install twrp recovery using Odin. Now my phone is not booting in recovery mode i already wipe the cache/system/vendor etc.... now my phone is restarting again and again
when i go to odin mode and flash android 9 its give error after param.bin
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5716 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Phone also says SW REV CHECK FAIL (Bootloader) Device 5, Binary: 4 after failed ODIN install
sorry for bad english...

Related

Question twrp recovery keeps changing to stock recovery

Hello guys,
I'm a bit new to posting things to this forum. My english isn't very good either :fingers-crossed:
My problem is:
i'm trying to install TWRP recovery to my s7. Everytime i install it with Odin everything works and when i reboot into recovery it goes automatically to my stock recovery.
LOG odin:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Could somebody please help me with my problem
I'm sorry if this has been asked before but i just can't find the awnser
i've used this tutorial: http://www.droidviews.com/install-twrp-galaxy-s7-exynos-variants-g930ffdxsw8/
Jesse050 said:
Hello guys,
I'm a bit new to posting things to this forum. My english isn't very good either :fingers-crossed:
My problem is:
i'm trying to install TWRP recovery to my s7. Everytime i install it with Odin everything works and when i reboot into recovery it goes automatically to my stock recovery.
LOG odin:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Could somebody please help me with my problem
I'm sorry if this has been asked before but i just can't find the awnser
i've used this tutorial: http://www.droidviews.com/install-twrp-galaxy-s7-exynos-variants-g930ffdxsw8/
Click to expand...
Click to collapse
I had the same problem. I just used chainfire 's auto root and then installed twrp with flashify.

after flashing Twrp can't come into Recovery Twrp

After flashing Twrp with Odin I can't acces Twrp Recovery. I think flashing was succesfully:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
when I boot device with Power button + volume up I see Samsung Galaxy Note 10.1 logo but no further movement. I can only restart device to stock rom.
How to come into Twrp Recovery ?
I solved the problem by using another Twrp. My device is a 2012 version of 10.1. I used Twrp version 2014.

Help: phone in "recovery booting" loop, trying to flash-

I have a Samsung Galaxy S7. It went into a boot loop and then when tried to do factory reset it went into a "recovery booting" loop. Seems only possible to enter download mode. From reading the forums, it seems the only possible option is a flash. I have downloaded Odin 3.13, and the Samsung drivers.
I downloaded file : G930VVRU4CRE5 (which I think is the oreo firmware)
When I "start" the process, it fails:
phone has error : SW REV CHECK FAIL : [aboot] Fused > Binary 4
odin shows:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5219 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Not sure where to go from here ? (do I need different firmware?)
Thank you for the assistance.
cgakdj21 said:
I have a Samsung Galaxy S7. It went into a boot loop and then when tried to do factory reset it went into a "recovery booting" loop. Seems only possible to enter download mode. From reading the forums, it seems the only possible option is a flash. I have downloaded Odin 3.13, and the Samsung drivers.
I downloaded file : G930VVRU4CRE5 (which I think is the oreo firmware)
When I "start" the process, it fails:
phone has error : SW REV CHECK FAIL : [aboot] Fused > Binary 4
odin shows:
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 5219 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Not sure where to go from here ? (do I need different firmware?)
Thank you for the assistance.
Click to expand...
Click to collapse
You need to use the patched version of Odin and the firmware your using needs to be U4 or above Verizon which I think you already have.
https://forum.xda-developers.com/android/software/patched-odin-3-13-1-t3762572

Cant flash any ROM in Samsung J7 pro

Hi ,
I cant flash any ROM in my Samsung J7 pro (SM - J730GM)
There is no ROM in the phone .
Tried TRWP
SHOWS - size of image is larger than target device
Tried ODIN-
SHOWS -
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1401)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3857 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
NEED HELP
THANK YOU

Galaxy J7 Prime.. Can't flash Stock Rom using Odin. "Custom Binary (System) Blocked by FRP lock"

Samsung Galaxy J7 Prime
SM-G610F
Region-XSG
About 2 weeks ago my phone died dropping battery to 0%. And, after I plug the phone to charger, it started bootlooping.
I flashed the stock firmware using Odin and It was successful. I used the phone as normal until yesterday.
Yesterday, the battery died again dropping to 0 %. And.., the bootloop problem came up again.
So I tried to flash the stock firmware again using Odin.
But not like before, It Failed to flash
Phone says "Custom Binary (System) Blocked by FRP lock"
Odin Fails at 'cache.img' when I select 'HOME_CSC_OJV' file as the CSC
Here is the log..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
...And, If I select 'CSC_OJV' as the CSC file, It Fails at 'userdata.img'
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> userdata.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
After forcing restart, The bluescreen comes up and it says,
"An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC Software"
But the Smart Switch Doesn't support my device
Please Help me to get my phone up and running....
Try Flash BL, AP, CP
then wipe date
windows4droid said:
Try Flash BL, AP, CP
then wipe date
Click to expand...
Click to collapse
Not workingg..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> userdata.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Try flash combination firmware
windows4droid said:
Try flash combination firmware
Click to expand...
Click to collapse
Hello... Can you please explain that?..
Thank you
Chamuditha Heshan said:
Hello... Can you please explain that?..
Thank you
Click to expand...
Click to collapse
404.67 MB file on MEGA
mega.nz
Download combination firmware
then flash it

Categories

Resources