Dasaita Sound Cutting Out - General Questions and Answers

I have a Dasaita head unit with Android 11 & Vivid 11 installed. My vehicle is a 2016 Jeep Cherokee with a 9 speaker system. Every 10 seconds the sound cuts out for a second. This happens with local radio and all music/video apps. In the Canbus it is set at 78 JEEP_Cherokee&Renegade&FiatAegea(Simple) anybody know what the issue may be?

Related

PX5 Android head unit no sound

I just bought a Belsee PX5 Octo Core Android Head Unit for my 2016 Hyundai Veloster. It has a custom harness made for the car. It works great, except there is no sound. The backup camera works, the steering wheel controls work. Everything works....except sound. I am trying to work with Belsee via Email, but we all know how that goes. I am wondering if any of you fine people might have any suggestions that I can try.
I have gone into Factory Settings menu and changed the CANBUS to Hyundai &KIA, still no sound. The Veloster requires a signal over the CANBUS to turn the factory Amp on and produce sound.
Thanx in advance.
what did the reseller suggest when you contacted them for support? Was that to change CanBus settings?
Hi, i have the same problem after upgrading from px3... Did you resolve the problem?
I now have sound..had to swap to a harness with a CANBUS controller on it. But, the EQ does not work, the rear speakers are super low, and there is that electrical whine from the engine. But at least there is sound.
Hi I am new here but I also had the same issue with my Nissan qashqai and the Bose system. I have found that on my vehicle in the Belsee power harness that pin 1 was not present which is the 12v positive that feeds the Bose sound system. I would suggest you get a wiring diagram for the cars head unit and check to see if this is the problem.

Peugeot 407 - daylight running lights

Hi, quick question.. is there anybody out there who can enable this option on his Android HU? Who has working DRL on Peugeot 407?
tnx..
Hi, I have the same problem, in the night, lights automatically turn on, but during day I must always manually turn on daylight lights
Maverickky said:
Hi, I have the same problem, in the night, lights automatically turn on, but during day I must always manually turn on daylight lights
Click to expand...
Click to collapse
I'm working with DRL problem all 2 months of this android multimedia.
I'm turned on DRL in PP2000 and it works with original peugeot radio. Multimedia turns it off.
I guess this is Canbus problem and it seems that today it is still not solved.
MGoris said:
I'm working with DRL problem all 2 months of this android multimedia.
I'm turned on DRL in PP2000 and it works with original peugeot radio. Multimedia turns it off.
I guess this is Canbus problem and it seems that today it is still not solved.
Click to expand...
Click to collapse
No solution yet?
gratnak said:
No solution yet?
Click to expand...
Click to collapse
Is it an MTCD/E unit.
The ptoblem is in canbus decoder see thes:
[PX3] Peugeot 407 - Factory parking sensors - steering wheel buttons
Hello All, From few days I'm owner of PX3 device for my Peugeot 407. I've go two issues which I'cant solve. I'm using original ROM Factory parking sensor It doesn't work with delivered CAN Bus (BAGOO PSA-BG-02 SW: V002) In product...
forum.xda-developers.com
Post:#148
plamenangelov said:
The ptoblem is in canbus decoder see thes:
[PX3] Peugeot 407 - Factory parking sensors - steering wheel buttons
Hello All, From few days I'm owner of PX3 device for my Peugeot 407. I've go two issues which I'cant solve. I'm using original ROM Factory parking sensor It doesn't work with delivered CAN Bus (BAGOO PSA-BG-02 SW: V002) In product...
forum.xda-developers.com
Post:#148
Click to expand...
Click to collapse
Hi,
is there a verified CANBUS that works well with 407?
I have following one:
PA-SS-07 20191229 SW:V1.00.012BYPS P/N:1814600028
used with PX5 9.0 4+64
rk3368-userdebug 9 PI 20200103.122402 test-keys Kernel 4.4.167 #193 Fri Dec 13 17:27:06 CST 2019 MCU version MTCE_MX_V3.41_1 Nov 15 2019 12:50:10 Octa-core Cortex-A53 @ 1.5G memory 3940 MB
I don't have parking sensors, so no issue there, the problems I observed are:
- no DRL (lights stopped switching on automatically, options in the Android app don't have any result)
- temperature not shown, I see no options to activate that in radio
- HU doesn't turn on on ignition ON every time, sometimes it's needed to start the engine first
- climate temperatures seem to be wrong - in the original controls it defaulted to 21 deg when turning on ignition (Webasto parking heater resets it), on the Android device it shows 23 deg, I don't know if 23 is equivalent to 21.
vorek22 said:
Hi,
is there a verified CANBUS that works well with 407?
I have following one:
PA-SS-07 20191229 SW:V1.00.012BYPS P/N:1814600028
used with PX5 9.0 4+64
rk3368-userdebug 9 PI 20200103.122402 test-keys Kernel 4.4.167 #193 Fri Dec 13 17:27:06 CST 2019 MCU version MTCE_MX_V3.41_1 Nov 15 2019 12:50:10 Octa-core Cortex-A53 @ 1.5G memory 3940 MB
I don't have parking sensors, so no issue there, the problems I observed are:
- no DRL (lights stopped switching on automatically, options in the Android app don't have any result)
- temperature not shown, I see no options to activate that in radio
- HU doesn't turn on on ignition ON every time, sometimes it's needed to start the engine first
- climate temperatures seem to be wrong - in the original controls it defaulted to 21 deg when turning on ignition (Webasto parking heater resets it), on the Android device it shows 23 deg, I don't know if 23 is equivalent to 21.
Click to expand...
Click to collapse
Hello, see this
[PX3] Peugeot 407 - Factory parking sensors - steering wheel buttons
Hello All, From few days I'm owner of PX3 device for my Peugeot 407. I've go two issues which I'cant solve. I'm using original ROM Factory parking sensor It doesn't work with delivered CAN Bus (BAGOO PSA-BG-02 SW: V002) In product...
forum.xda-developers.com

Help: Audi a3 with android head unit

Hello, all good people, professionals, beginners. I am Slovak for the introduction and therefore your language is not my natural so I apologize in advance. What i can't write, translate in google.
I have audi a3 12.2009 sportback gen2. My original radio 8P0035186P.
Air condition 8P0820043BH
Central electrics 8P0907279N
Gateway 1K0907951
Parking assitance 8P0919475B
Steering assistance 1K0909144C
Dashboard 8P0920931T
I buy android head unit px5 1024x600 rk3368 A10 octa core cortex-a53 2gb ram 32gb rom. (mtce_chs_v3.67_1 Nov 7 2020) (core 4.19.111+ Nov 23 2020) Canbus decoder CHS 20201201 A3/A4/TT HW:v3 SW:v1.
What works: steering wheel control, day / night mode change via sensor, battery/alt voltage - that is all. Used CANBUS protocol audi A3 simple 1/2 gen in factory settings.
I have the following problems and questions: The car does not communicate with the radio at all. Radio does not display vehicle management, applications or something for any communication between the vehicle and the unit. When I change the canbus protocol to golf7 or high class audi in factory settings, will be displayed after restart - vehicleapp and controlsettingsapp. When I run the application in canbus golf, turns on but everything is unavailable. As a layman i tried to pull the app from canbus golf7 to my audi a3 simple canbus and install. The application will install, but stop immediately. What I'm doing wrong or where I should look for a mistake according to you? Why I don't have these applications there at canbus a3 simple?
I called Audi support and I asked them supports my vehicle these things: Parking radar/assistant, open doors, air conditioning, tpms and more.. They said yes but only if you have rns-e radio. Rns-e dont have bluetooth and other good staff so i buy this and I am unhappy. I use obdeleven when I turn on a function, for example parking ilustration the function will disappear from my dashboard and for me logically sends the sensor control to the radio. But no and why? it's radio too waste or audi just can't do it? I will answer every question by attaching any file ask anything.

Question Xtrons Head unit for 2010 Lexus IS250, cant get some Steering Wheel Controls to work!

Hi everyone
I have a facelift 2010 Lexus IS250 F Sport, I've had some large success installing this XTRONS head unit for it and I am largely satisfied with it. I am however having an issue with getting Steering Wheel Controls to work with the head unit.
Lexus | Various | Android 10 | Octa Core | 4GB RAM & 64GB ROM | Integrated 4G Solution | PMA10ISLS
XTRONS PMA10ISLS is a 10.1" large screen car stereo with customized face panel and optimized CANbus Decoding for Lexus. It supports CarAutoPlay, built-in DSP, PIP mode enabled ,Dual Theme, Instant Rear Vision and so on.
xtrons.co.uk
Lexus| Various | ISO Wiring Harness | MOST
This ISO Wiring Harness is compatible with XTRONS custom fit units PSP10ISL,PMA10ISL etc. If your car is Lexus IS250/IS300/IS350 Convertible (2-door)with original navigation or fibre amplfier system,you need this cable to aid for the installation.
xtrons.co.uk
This is the unit I purchased, alongside a special wiring harness so that I could use it with my vehicle as its a facelift Navi.
With the default CANbus setting on my head unit, only Volume control seems to work and the phone call buttons and voice command buttons are mapped to functions like Radio and Hey Google but I cannot programme these on the app. With an alternative CANbus setting I get skip track functionality but I get different AC Controls and lose access to my factory amp settings.
The original wiring harness I got for the headhunt has not been used at all as I was instructed to usr the special harness, and that original harness had a CANBUS decoder. XTRONS claim that I am unable to programme the SWC due to the CANBUS needing to decode it, although I have played around with the settings and selected various different CANBUS settings.
Would anyone be able to advise me on how I can get the SWC working, would it involve plugging the CANbus decoder into the head unit? There is a 12 pin connection spare at the back but I am unsure if that would make the difference or not.

Head unit turns Off After 10 Minutes

Yo maybe someone can help me
I bought a Android Head unit widths Canbus
I installed everything and it goes on everything fine
But after around 10 Minutes of Driving the Head Unit just turns Off
I removed the Canbus and now it just in Standby Mode 24/7 so that isn’t the solution cause it’s draining the Battery
What could be the issue?
I am Driving a Volkswagen Golf Mk5 from 2006
Is it MTCD post Android system information including MCU version

Categories

Resources