Related
I have running a desire s with runndroid by the pvteam. I flashed it about a week ago.
This morning I found my phone locked up, It would not become active. I pulled the battery and attempted to reboot. it now just sits on the initial flash screen.
after a lot of mucking about in EXT4 recovery, I feel my problem is that hte system not mounting /data /system and /cache... it just won mount because when I attempt to mount in the recovery I just get an error.. in abd shell.... I get:
# mount -a
mount: mounting /dev/block/mmcblk0p27 on /cache failed: Invalid argument
mount: mounting /dev/block/mmcblk0p26 on /data failed: Invalid argument
mount: mounting /dev/block/mmcblk0p25 on /system failed: Invalid argument
I have formatted, I have repartitioned and I have reflashed my room. It wont boot, these wont mount.
any ideas?
ah, I just had a brain wave...
#dmesg in the shell.... . I have lots of IO errors:
<3>[ 1660.224365] end_request: I/O error, dev mmcblk0, sector 1384779
<3>[ 1660.224456] end_request: I/O error, dev mmcblk0, sector 1384780
<3>[ 1660.224639] end_request: I/O error, dev mmcblk0, sector 1384781
<3>[ 1660.224761] end_request: I/O error, dev mmcblk0, sector 1384782
<3>[ 1660.224945] end_request: I/O error, dev mmcblk0, sector 1384783
the phone is bricked I assume? the internal NAN has failed?
ye, everytime I attempt to mount I get the following:
<3>[ 2225.836029] mmc0: DMA channel flushed (0x80000004)
<3>[ 2225.836425] Flush data: 0000c003 0bb03000 00000000 00400040 00100010 00000003
<6>[ 2225.837127] mmc0: Controller has been reset
<6>[ 2225.837585] mmc0: Worked around bug 1535304
<3>[ 2225.838256] mmcblk0: error -110 sending read command, response 0x40ff8080
<4>[ 2225.838653] mmcblk0: retrying using single block read
<3>[ 2225.840332] mmc0: DMA channel flushed (0x80000004)
<3>[ 2225.840698] Flush data: 0000c003 0bb03000 00000000 00400040 00080008 00000003
<6>[ 2225.841430] mmc0: Controller has been reset
<6>[ 2225.841857] mmc0: Worked around bug 1535304
<3>[ 2225.848571] mmcblk0: error -110 sending status comand
<3>[ 2225.848937] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x0
<3>[ 2225.849945] mmcblk0: error -5 transferring data, sector 1343490, nr 2, card status 0x0
<6>[ 2225.850585] mmc0: reinit card
<4>[ 2225.850952] mmc0: Starting deferred resume
<6>[ 2228.035705] mmc0: Deferred resume failed
<3>[ 2228.035827] end_request: I/O error, dev mmcblk0, sector 1343490
<3>[ 2228.036041] EXT3-fs (mmcblk0p26): error: unable to read superblock
<3>[ 2228.036560] mmc_blk_issue_rq failed!!
<3>[ 2228.037750] mmc0: DMA channel flushed (0x80000004)
<3>[ 2228.037841] Flush data: 0000c003 0bb03000 00000000 00400040 00100010 00000003
<6>[ 2228.038116] mmc0: Controller has been reset
<6>[ 2228.038299] mmc0: Worked around bug 1535304
<3>[ 2228.038482] mmcblk0: error -110 sending read command, response 0x40ff8080
<4>[ 2228.038604] mmcblk0: retrying using single block read
<3>[ 2228.039764] mmc0: DMA channel flushed (0x80000004)
<3>[ 2228.039855] Flush data: 0000c003 0bb03000 00000000 00400040 00080008 00000003
<6>[ 2228.040130] mmc0: Controller has been reset
<6>[ 2228.040283] mmc0: Worked around bug 1535304
<3>[ 2228.046295] mmcblk0: error -110 sending status comand
<3>[ 2228.046478] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x0
<3>[ 2228.046752] mmcblk0: error -5 transferring data, sector 1343490, nr 2, card status 0x0
<6>[ 2228.046844] mmc0: reinit card
<4>[ 2228.047027] mmc0: Starting deferred resume
<6>[ 2230.288024] mmc0: Deferred resume failed
<3>[ 2230.288421] end_request: I/O error, dev mmcblk0, sector 1343490
<3>[ 2230.289123] EXT2-fs (mmcblk0p26): error: unable to read superblock
<3>[ 2230.290466] mmc_blk_issue_rq failed!!
<3>[ 2230.292266] mmc0: DMA channel flushed (0x80000004)
<3>[ 2230.292633] Flush data: 0000c003 0bb03000 00000000 00400040 00100010 00000003
<6>[ 2230.293365] mmc0: Controller has been reset
<6>[ 2230.293792] mmc0: Worked around bug 1535304
<3>[ 2230.294494] mmcblk0: error -110 sending read command, response 0x40ff8080
<4>[ 2230.294860] mmcblk0: retrying using single block read
<3>[ 2230.296569] mmc0: DMA channel flushed (0x80000004)
<3>[ 2230.296936] Flush data: 0000c003 0bb03000 00000000 00400040 00080008 00000003
<6>[ 2230.297668] mmc0: Controller has been reset
<6>[ 2230.298095] mmc0: Worked around bug 1535304
<3>[ 2230.304412] mmcblk0: error -110 sending status comand
<3>[ 2230.305084] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x0
<3>[ 2230.306060] mmcblk0: error -5 transferring data, sector 1343490, nr 2, card status 0x0
<6>[ 2230.306457] mmc0: reinit card
<4>[ 2230.306793] mmc0: Starting deferred resume
<6>[ 2232.540161] mmc0: Deferred resume failed
<3>[ 2232.540283] end_request: I/O error, dev mmcblk0, sector 1343490
<3>[ 2232.540496] EXT4-fs (mmcblk0p26): unable to read superblock
<3>[ 2232.540954] mmc_blk_issue_rq failed!!
<3>[ 2232.542236] mmc0: DMA channel flushed (0x80000004)
<3>[ 2232.542327] Flush data: 0000c003 0bb03000 00000000 00400040 00080008 00000003
<6>[ 2232.542602] mmc0: Controller has been reset
<6>[ 2232.542755] mmc0: Worked around bug 1535304
<3>[ 2232.548767] mmcblk0: error -110 sending status comand
<3>[ 2232.548950] mmcblk0: error -110 sending read/write command, response 0x40ff8080, card status 0x0
<3>[ 2232.549255] mmcblk0: error -5 transferring data, sector 1343488, nr 1, card status 0x0
<6>[ 2232.549346] mmc0: reinit card
<4>[ 2232.549438] mmc0: Starting deferred resume
<6>[ 2234.632263] mmc0: Deferred resume failed
<3>[ 2234.632629] end_request: I/O error, dev mmcblk0, sector 1343488
<3>[ 2234.633361] FAT: unable to read boot sector
<3>[ 2234.635650] mmc_blk_issue_rq failed!!
Unfortunately it looks like your right, I'm just wondering why you still can access recovery, to be sure pls make a reboot to recovery and straight afterwards execute dmesg | grep mmc0.
You can try to replace your bootloader and check if it works, even take a look at the index, at the bottom is a thread named read this before going to replace emmc chip.
And pls tell what bootloader you're using.
Swyped from my Desire S far away from my PC (maybe)
# dmesg | grep mmc0
<3>[ 7.411163] mmc0: No card detect facilities available
<6>[ 7.411682] mmc0: Qualcomm MSM SDCC at 0x00000000a0500000 irq 98,0 dma 7
<6>[ 7.411926] mmc0: Platform slot type: MMC
<6>[ 7.412048] mmc0: 4 bit data mode disabled
<6>[ 7.412292] mmc0: 8 bit data mode enabled
<6>[ 7.412414] mmc0: MMC clock 144000 -> 50000000 Hz, PCLK 96000000 Hz
<6>[ 7.412658] mmc0: Slot eject status = 0
<6>[ 7.412780] mmc0: Power save feature enable = 1
<6>[ 7.412902] mmc0: DM non-cached buffer at ffa0f000, dma_addr 0x0c250000
<6>[ 7.413146] mmc0: DM cmd busaddr 0x0c250000, cmdptr busaddr 0x0c250300
<6>[ 7.566467] mmc0: new high speed MMC card at address 0001
<6>[ 7.567840] mmcblk0: mmc0:0001 M4G2DE 2.10 GiB
<3>[ 67.214080] mmc0: Failed to get card ready i = 122482
<6>[ 67.214263] mmc0: reinit card
<4>[ 67.214355] mmc0: Starting deferred resume
<6>[ 69.626434] mmc0: Deferred resume failed
is the dmesg output.... asi you can see....... can not mount it.. .:\
and as your post says"
http://forum.xda-developers.com/showthread.php?t=1284196
mmc0: failed to get card ready
mmc0: reinit card
mmc0: Starting deferred resume
mmc0: Deferred resume failed
Than you internal memory (eMMC) is corrupted i.e. your chip is "fried". This is a hardware issue (reference here) and the chip has to be replaced. Sorry, no other solutions available.
thanks for your help!
Sry, missed it at the op, but this will always stay a riddle to me.
How the hell is it possible to access a recovery located on mmc0 without a working mmc0, anyways.
There is a thread introducing a replacement emmc confirmed working out of the box, if you like to repair it yourself and save a lot of money
Swyped from my Desire S far away from my PC (maybe)
Tectas said:
Sry, missed it at the op, but this will always stay a riddle to me.
How the hell is it possible to access a recovery located on mmc0 without a working mmc0, anyways.
There is a thread introducing a replacement emmc confirmed working out of the box, if you like to repair it yourself and save a lot of money
Swyped from my Desire S far away from my PC (maybe)
Click to expand...
Click to collapse
yeah, you got me!
um, do you have a link to that mentioned thread? I will at the worst have a look at replacing it....
http://forum.xda-developers.com/showthread.php?t=1543310
Swyped from my Desire S far away from my PC (maybe)
But found something additional, maybe you're willing to try because you got nothing to lose^^
The only thing a bit tricky could be to find the right backup location of the superblock.
How to restore superblock http://linuxpoison.blogspot.com/2007/10/how-to-recover-damaged-superblock.html?m=1
Edit: Here is how to find the backup locations of the superblock http://www.cyberciti.biz/faq/recover-bad-superblock-from-corrupted-partition/
Swyped from my Desire S far away from my PC (maybe)
If I upload cm-10.1 would someone test it?
Unjustified Dev said:
If I upload cm-10.1 would someone test it?
Click to expand...
Click to collapse
I will be brave and test it. (was actually going to try and build it myself soon)
chevyowner said:
I will be brave and test it. (was actually going to try and build it myself soon)
Click to expand...
Click to collapse
Thanks about 6 hours no rest trying to figure out which blobs matter , constantly comparing nvidia tablets, and finally getting it to build.
I'm running a fresh build now I already built it like 5 times already
This only makes me want this device more:laugh:
Here is my source
device - https://github.com/Project-Shield/android_device_nvidia_roth
vendor- https://github.com/Project-Shield/proprietarty_vendor_nvidia_roth
kernel- https://github.com/Project-Shield/android_kernel_nvidia_roth
I got the kernel from another source you can see where I forked it.
The libs I weren't to sure on but I started from the nexus 7 list and added more
I will put up a guide soon I did exclude nvidia/device/common and drivers/sensors from my github im going to integrate it into one tree instead of separate folders.
@chevyowner Here it is I really hope it boots http://goo.im/devs/Unjust/Roth/cm-10.1-20130809-UNOFFICIAL-roth.zip
Downloading now, I hope my internet does not decide it hates me again while downloading.
chevyowner said:
Downloading now, I hope my internet does not decide it hates me again while downloading.
Click to expand...
Click to collapse
Thanks I really appreciate it idc if it doesnt boot but at least start up to get a logcat if possible but im sure you want it to start up
error 7 flashing, looking to see if it is something I did.
chevyowner said:
error 7 flashing, looking to see if it is something I did.
Click to expand...
Click to collapse
Weird it used device specific partitions in cwm after it fails go to advanced and then show log
That did not help me so I looked and agrabren called shield thor not roth after changing roth to thor in the updater script it flashed. It won't boot tho.
I can't get logcat working.
chevyowner said:
That did not help me so I looked and agrabren called shield thor not roth after changing roth to thor in the updater script it flashed. It won't boot tho.
I can't get logcat working.
Click to expand...
Click to collapse
Does it at least boot or is a black screen by boot I mean at least show the bootanimation ?
Hangs at the nvidia shield screen. I found my usbview.exe and Windows thinks nothing is plugged in. (except for my xbox360 controller and keyboard)
chevyowner said:
Hangs at the nvidia shield screen. I found my usbview.exe and Windows thinks nothing is plugged in. (except for my xbox360 controller and keyboard)
Click to expand...
Click to collapse
In recovery type su then adb shell cat proc/last_kmsg ot adb shell cat proc_kmsg could you post them
Most likely i am missing a blob thats the only reason I can see it staying at the bootlogo
I did just fix the status 7 error
Night man sorry for wasting your time
The recovery does not have /proc/last_kmsg, I will try more when I think of it.
chevyowner said:
The recovery does not have /proc/last_kmsg, I will try more when I think of it.
Click to expand...
Click to collapse
try cat proc/kmsg or adb shell dmesg thanks for this because as soon as booted I was going to kick this aside and start on 4.3
kmsg
Code:
sysfs_add_one+0x90/0xb0)
<4>[ 2.102778] [<c017f7fc>] (sysfs_add_one+0x90/0xb0) from [<c017fa54>] (create_dir+0x68/0xc4)
<4>[ 2.102904] [<c017fa54>] (create_dir+0x68/0xc4) from [<c017fdc0>] (sysfs_create_dir+0x6c/0xb0)
<4>[ 2.103123] [<c017fdc0>] (sysfs_create_dir+0x6c/0xb0) from [<c02796cc>] (kobject_add_internal+0xb0/0x278)
<4>[ 2.103359] [<c02796cc>] (kobject_add_internal+0xb0/0x278) from [<c0279ccc>] (kobject_add+0x4c/0x94)
<4>[ 2.103579] [<c0279ccc>] (kobject_add+0x4c/0x94) from [<c0279f34>] (kobject_create_and_add+0x28/0x64)
<4>[ 2.103798] [<c0279f34>] (kobject_create_and_add+0x28/0x64) from [<c03530f0>] (class_compat_register+0x40/0x70)
<4>[ 2.104021] [<c03530f0>] (class_compat_register+0x40/0x70) from [<c052bd4c>] (create_extcon_class+0x54/0x98)
<4>[ 2.104282] [<c052bd4c>] (create_extcon_class+0x54/0x98) from [<c0008674>] (do_one_initcall+0xa0/0x100)
<4>[ 2.104415] [<c0008674>] (do_one_initcall+0xa0/0x100) from [<c0a1b8e4>] (do_initcalls+0x78/0xac)
<4>[ 2.104630] [<c0a1b8e4>] (do_initcalls+0x78/0xac) from [<c0a1b9a8>] (kernel_init+0x90/0x128)
<4>[ 2.104847] [<c0a1b9a8>] (kernel_init+0x90/0x128) from [<c000f8b8>] (kernel_thread_exit+0x0/0x8)
<4>[ 2.105073] ---[ end trace 9d1c79c81885dc7d ]---
<4>[ 2.105207] ------------[ cut here ]------------
<4>[ 2.105329] WARNING: at /home/agrabren/android/roms/cm-10.1/kernel/nvidia/thor/lib/kobject.c:198 kobject_add_internal+0x20c/0x278()
<4>[ 2.105627] kobject_add_internal failed for switch with -EEXIST, don't try to register things with the same name in the same directory.
<4>[ 2.105833] Modules linked in:
<4>[ 2.106061] [<c00159d8>] (unwind_backtrace+0x0/0x140) from [<c006078c>] (warn_slowpath_common+0x54/0x6c)
<4>[ 2.106301] [<c006078c>] (warn_slowpath_common+0x54/0x6c) from [<c0060850>] (warn_slowpath_fmt+0x38/0x48)
<4>[ 2.106526] [<c0060850>] (warn_slowpath_fmt+0x38/0x48) from [<c0279828>] (kobject_add_internal+0x20c/0x278)
<4>[ 2.106662] [<c0279828>] (kobject_add_internal+0x20c/0x278) from [<c0279ccc>] (kobject_add+0x4c/0x94)
<4>[ 2.106888] [<c0279ccc>] (kobject_add+0x4c/0x94) from [<c0279f34>] (kobject_create_and_add+0x28/0x64)
<4>[ 2.107115] [<c0279f34>] (kobject_create_and_add+0x28/0x64) from [<c03530f0>] (class_compat_register+0x40/0x70)
<4>[ 2.107365] [<c03530f0>] (class_compat_register+0x40/0x70) from [<c052bd4c>] (create_extcon_class+0x54/0x98)
<4>[ 2.107589] [<c052bd4c>] (create_extcon_class+0x54/0x98) from [<c0008674>] (do_one_initcall+0xa0/0x100)
<4>[ 2.107809] [<c0008674>] (do_one_initcall+0xa0/0x100) from [<c0a1b8e4>] (do_initcalls+0x78/0xac)
<4>[ 2.107942] [<c0a1b8e4>] (do_initcalls+0x78/0xac) from [<c0a1b9a8>] (kernel_init+0x90/0x128)
<4>[ 2.108165] [<c0a1b9a8>] (kernel_init+0x90/0x128) from [<c000f8b8>] (kernel_thread_exit+0x0/0x8)
<4>[ 2.108397] ---[ end trace 9d1c79c81885dc7e ]---
<4>[ 2.108517] kobject_create_and_add: kobject_add error: -17
<4>[ 2.108728] ------------[ cut here ]------------
<4>[ 2.108856] WARNING: at /home/agrabren/android/roms/cm-10.1/kernel/nvidia/thor/drivers/extcon/extcon_class.c:545 create_extcon_class+0x78/0x98()
<4>[ 2.109071] cannot allocate
<4>[ 2.109291] Modules linked in:
<4>[ 2.109633] [<c00159d8>] (unwind_backtrace+0x0/0x140) from [<c006078c>] (warn_slowpath_common+0x54/0x6c)
<4>[ 2.109855] [<c006078c>] (warn_slowpath_common+0x54/0x6c) from [<c0060850>] (warn_slowpath_fmt+0x38/0x48)
<4>[ 2.110080] [<c0060850>] (warn_slowpath_fmt+0x38/0x48) from [<c052bd70>] (create_extcon_class+0x78/0x98)
<4>[ 2.110229] [<c052bd70>] (create_extcon_class+0x78/0x98) from [<c0008674>] (do_one_initcall+0xa0/0x100)
<4>[ 2.110366] [<c0008674>] (do_one_initcall+0xa0/0x100) from [<c0a1b8e4>] (do_initcalls+0x78/0xac)
<4>[ 2.110588] [<c0a1b8e4>] (do_initcalls+0x78/0xac) from [<c0a1b9a8>] (kernel_init+0x90/0x128)
<4>[ 2.110811] [<c0a1b9a8>] (kernel_init+0x90/0x128) from [<c000f8b8>] (kernel_thread_exit+0x0/0x8)
<4>[ 2.111024] ---[ end trace 9d1c79c81885dc7f ]---
<3>[ 2.117575] mmc0: Command timeout error, intmask: 10001
<3>[ 2.120177] mmc0: Command timeout error, intmask: 10001
<3>[ 2.128564] mmc0: Command timeout error, intmask: 10001
<3>[ 2.131053] mmc0: Command timeout error, intmask: 10001
<3>[ 2.133662] mmc0: Command timeout error, intmask: 10001
<3>[ 2.136144] mmc0: Command timeout error, intmask: 10001
<3>[ 2.138771] mmc0: Command timeout error, intmask: 10001
<3>[ 2.141261] mmc0: Command timeout error, intmask: 10001
<3>[ 2.143847] mmc0: Command timeout error, intmask: 10001
<3>[ 2.146357] mmc0: Command timeout error, intmask: 10001
<3>[ 2.148956] mmc0: Command timeout error, intmask: 10001
<6>[ 2.190251] usb 1-1: new full-speed USB device number 2 using tegra-ehci
<6>[ 2.194790] mmc0: new high speed DDR MMC card at address 0001
<6>[ 2.195114] mmcblk mmc0:0001: Card claimed for testing.
<6>[ 2.195597] mmcblk0: mmc0:0001 MAG2GA 14.5 GiB
<6>[ 2.195952] mmcblk0boot0: mmc0:0001 MAG2GA partition 1 2.00 MiB
<6>[ 2.196412] mmcblk0boot1: mmc0:0001 MAG2GA partition 2 2.00 MiB
<4>[ 2.198299] Primary GPT is invalid, using alternate GPT.
<6>[ 2.198573] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12
<6>[ 2.201579] mmcblk0boot1: unknown partition table
<6>[ 2.202875] mmcblk0boot0: unknown partition table
<6>[ 2.209793] usbcore: registered new interface driver snd-usb-audio
<6>[ 2.217690] usb 1-1: New USB device found, idVendor=0955, idProduct=7203
<6>[ 2.217904] usb 1-1: New USB device strings: Mfr=2, Product=1, SerialNumbe
r=0
<6>[ 2.218111] usb 1-1: Product: NVIDIA Controller v01.01
<6>[ 2.218247] usb 1-1: Manufacturer: NVIDIA Corporation
<6>[ 2.224902] input: NVIDIA Corporation NVIDIA Controller v01.01 as /devices
/platform/tegra-ehci.2/usb1/1-1/1-1:1.0/input/input1
<6>[ 2.225520] generic-usb 0003:0955:7203.0001: input: USB HID v1.11 Gamepad
[NVIDIA Corporation NVIDIA Controller v01.01] on usb-tegra-ehci.2-1/input0
<3>[ 2.239328] mmc1: Command timeout error, intmask: 10001
<3>[ 2.241820] mmc1: Command timeout error, intmask: 10001
<3>[ 2.249889] mmc1: Command timeout error, intmask: 10001
<3>[ 2.252376] mmc1: Command timeout error, intmask: 10001
<3>[ 2.254944] mmc1: Command timeout error, intmask: 10001
<3>[ 2.257427] mmc1: Command timeout error, intmask: 10001
<6>[ 2.302518] mmc1: new high speed SDHC card at address 0001
<6>[ 2.302806] mmcblk mmc1:0001: Card claimed for testing.
<6>[ 2.303312] mmcblk1: mmc1:0001 00000 7.41 GiB
<6>[ 2.318663] mmcblk1: p1
<3>[ 2.354587] mmc2: Command timeout error, intmask: 10001
<3>[ 2.357165] mmc2: Command timeout error, intmask: 10001
<3>[ 2.365554] mmc2: Command timeout error, intmask: 10001
<3>[ 2.368131] mmc2: Command timeout error, intmask: 10001
<3>[ 2.370614] mmc2: Command timeout error, intmask: 10001
<3>[ 2.373095] mmc2: Command timeout error, intmask: 10001
<3>[ 2.375662] mmc2: Command timeout error, intmask: 10001
<3>[ 2.378148] mmc2: Command timeout error, intmask: 10001
<3>[ 2.380963] mmc2: Command timeout error, intmask: 10001
<3>[ 2.383450] mmc2: Command timeout error, intmask: 10001
<3>[ 2.386021] mmc2: Command timeout error, intmask: 10001
<3>[ 2.388537] mmc2: Command timeout error, intmask: 10001
<3>[ 2.427687] mmc2: Command timeout error, intmask: 10001
<3>[ 2.430285] mmc2: Command timeout error, intmask: 10001
<3>[ 2.438654] mmc2: Command timeout error, intmask: 10001
<3>[ 2.441249] mmc2: Command timeout error, intmask: 10001
<3>[ 2.443920] mmc2: Command timeout error, intmask: 10001
<3>[ 2.446509] mmc2: Command timeout error, intmask: 10001
<3>[ 2.449093] mmc2: Command timeout error, intmask: 10001
<3>[ 2.451769] mmc2: Command timeout error, intmask: 10001
<3>[ 2.454360] mmc2: Command timeout error, intmask: 10001
<3>[ 2.457035] mmc2: Command timeout error, intmask: 10001
<3>[ 2.459640] mmc2: Command timeout error, intmask: 10001
<3>[ 2.462330] mmc2: Command timeout error, intmask: 10001
<3>[ 2.501891] mmc2: Command timeout error, intmask: 10001
<3>[ 2.504779] mmc2: Command timeout error, intmask: 10001
<3>[ 2.512863] mmc2: Command timeout error, intmask: 10001
<3>[ 2.515756] mmc2: Command timeout error, intmask: 10001
<3>[ 2.518550] mmc2: Command timeout error, intmask: 10001
<3>[ 2.521430] mmc2: Command timeout error, intmask: 10001
<3>[ 2.524219] mmc2: Command timeout error, intmask: 10001
<3>[ 2.527015] mmc2: Command timeout error, intmask: 10001
<3>[ 2.529899] mmc2: Command timeout error, intmask: 10001
<3>[ 2.532698] mmc2: Command timeout error, intmask: 10001
<3>[ 2.535582] mmc2: Command timeout error, intmask: 10001
<3>[ 2.538387] mmc2: Command timeout error, intmask: 10001
<3>[ 2.578506] mmc2: Command timeout error, intmask: 10001
<3>[ 2.582152] mmc2: Command timeout error, intmask: 10001
<3>[ 2.591476] mmc2: Command timeout error, intmask: 10001
<3>[ 2.594885] mmc2: Command timeout error, intmask: 10001
<3>[ 2.598374] mmc2: Command timeout error, intmask: 10001
<3>[ 2.601774] mmc2: Command timeout error, intmask: 10001
<3>[ 2.605174] mmc2: Command timeout error, intmask: 10001
<3>[ 2.608584] mmc2: Command timeout error, intmask: 10001
<3>[ 2.611994] mmc2: Command timeout error, intmask: 10001
<3>[ 2.615523] mmc2: Command timeout error, intmask: 10001
<3>[ 2.618933] mmc2: Command timeout error, intmask: 10001
<3>[ 2.622461] mmc2: Command timeout error, intmask: 10001
<6>[ 3.016385] tegra-snd-rt5640 tegra-snd-rt5640.0: No speaker regulator found
<6>[ 3.169518] gpio wake49 for gpio=143
<6>[ 3.170052] asoc: rt5640-aif1 <-> tegra30-i2s.1 mapping ok
<6>[ 3.170833] asoc: dit-hifi <-> tegra30-spdif mapping ok
<6>[ 3.171298] asoc: dit-hifi <-> tegra30-i2s.3 mapping ok
<6>[ 3.173150] input: tegra-rt5640 Headphone Jack as /devices/platform/tegra-snd-rt5640.0/sound/card1/input2
<6>[ 3.174472] oprofile: using timer interrupt.
<6>[ 3.174990] GACT probability NOT on
<6>[ 3.175109] Mirror/redirect action on
<6>[ 3.175244] u32 classifier
<6>[ 3.175441] Actions configured
<6>[ 3.175554] Netfilter messages via NETLINK v0.30.
<6>[ 3.175733] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
<6>[ 3.176456] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[ 3.176846] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[ 3.177183] xt_time: kernel timezone is -0000
<6>[ 3.177749] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 3.178186] arp_tables: (C) 2002 David S. Miller
<6>[ 3.178385] TCP: cubic registered
<6>[ 3.178949] NET: Registered protocol family 10
<6>[ 3.180174] Mobile IPv6
<6>[ 3.180352] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 3.180944] IPv6 over IPv4 tunneling driver
<6>[ 3.182282] NET: Registered protocol family 17
<6>[ 3.182420] NET: Registered protocol family 15
<6>[ 3.182626] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 3.183027] NET: Registered protocol family 35
<6>[ 3.183459] NET: Registered protocol family 37
<6>[ 3.183575] NET: Registered protocol family 40
<6>[ 3.185990] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
<5>[ 3.186283] Registering SWP/SWPB emulation handler
<4>[ 3.209333] Disabling clocks left on by bootloader:
<4>[ 3.209454] xusb_hs_src
<4>[ 3.209573] audio_2x
<4>[ 3.209776] audio4_2x
<4>[ 3.209888] audio3_2x
<4>[ 3.210001] audio2_2x
<4>[ 3.210115] audio1_2x
<4>[ 3.210245] audio0_2x
<4>[ 3.210448] audio
<4>[ 3.210558] audio4
<4>[ 3.210839] audio3
<4>[ 3.210949] audio2
<4>[ 3.211058] audio1
<4>[ 3.211270] audio0
<4>[ 3.211458] dsi2-fixed
<4>[ 3.211569] dsi1-fixed
<4>[ 3.211694] uarta_dbg
<4>[ 3.211812] uarta
<4>[ 3.212015] mipi-cal-fixed
<4>[ 3.212125] mipi-cal
<4>[ 3.212258] bsev
<4>[ 3.212390] fuse_burn
<4>[ 3.212511] cclk_lp
<4>[ 3.212624] pll_x_out0
<4>[ 3.212903] pll_u_12M
<4>[ 3.213019] pll_u_60M
<4>[ 3.213135] pll_d2_out0
<4>[ 3.213351] pll_p_out3
<4>[ 3.213469] pll_c_out1
<4>[ 3.213583] pll_m_out1
<6>[ 3.213706] DVFS: Got RTC device name:rtc0
<6>[ 3.215035] palmas-rtc palmas-rtc.3: palmas_rtc_read_time() 113 7 9 4 23 56
<4>[ 3.215506] tegra_dvfs: vdd_cpu: stats above 1390 mV will be squashed
<4>[ 3.216260] tegra_dvfs: vdd_core: stats above 1390 mV will be squashed
<6>[ 3.224846] Tegra CPU DFLL is initialized
<6>[ 3.225222] CPU rate: 613 MHz
<6>[ 3.227088] cpu_dfll cooling device is registered
<6>[ 3.446327] tegra dvfs: tegra sysfs cap interface is initialized
<6>[ 3.446556] tegra dvfs: tegra sysfs floor interface is initialized
<6>[ 3.449424] Core EDP sysfs interface is initialized
<6>[ 3.450850] tegra_actmon.emc: Completed initialization (0)
<6>[ 3.451182] tegra_actmon.avp: Completed initialization (0)
<6>[ 3.453394] vi vi: vi_probe: ++
<6>[ 3.453495] vi vi: tegra_camera_register: ++
<6>[ 3.454851] vi vi: initialized
<4>[ 3.456464] palmas_regen2: incomplete constraints, leaving on
<4>[ 3.458176] palmas_smps12: incomplete constraints, leaving on
<6>[ 3.458964] gpio wake51 for gpio=128
<6>[ 3.459260] gpio wake23 for gpio=69
<6>[ 3.459400] gpio wake27 for gpio=144
<6>[ 3.459793] input: gpio-keys as /devices/platform/gpio-keys.0/input/input3
<6>[ 3.461122] palmas-rtc palmas-rtc.3: palmas_rtc_read_time() 113 7 9 4 23 56
<6>[ 3.461340] palmas-rtc palmas-rtc.3: setting system clock to 2013-08-09 04:23:56 UTC (1376022236)
<6>[ 3.461756] ALSA device list:
<6>[ 3.461852] #0: HDA NVIDIA Tegra at 0x70038000 irq 113
<6>[ 3.462022] #1: tegra-rt5640
<4>[ 3.462159] Warning: unable to open an initial console.
<3>[ 3.465118] init: could not import file '/init.recovery.roth.rc' from '/init.rc'
<3>[ 3.556839] android_usb: already disabled
<3>[ 3.557462] init: Unable to open persistent property directory /data/property errno: 2
<4>[ 3.602852] tegradc tegradc.0: DC doesn't stop at end of frame.
<4>[ 3.856850] tegradc tegradc.0: DC doesn't stop at end of frame.
<3>[ 3.857389] tegradc tegradc.0: DSI pad calibration done
<6>[ 4.463805] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts:
<6>[ 4.610329] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts:
<3>[ 4.616236] android_usb: already disabled
<6>[ 4.618169] adb_open
<6>[ 4.618314] adb_bind_config
<6>[ 4.621974] tegra-udc tegra-udc.0: detected SDP port
<6>[ 4.622095] bq2419x 0-006b: Setting charging current 2
<6>[ 4.729226] android_work: did not send uevent (0 0 (null))
<6>[ 4.765740] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 4.769283] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 4.823241] bq2419x 0-006b: Charging enabled
<6>[ 4.849696] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 4.984224] tegra-udc tegra-udc.0: detected SDP port
<6>[ 4.984350] bq2419x 0-006b: Setting charging current 2
<6>[ 5.124263] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 5.161733] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 5.165407] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 5.185224] bq2419x 0-006b: Charging enabled
<6>[ 5.245744] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 5.252164] android_usb gadget: high-speed config #1: android
<6>[ 5.252511] tegra-udc tegra-udc.0: detected SDP port
<6>[ 5.252832] bq2419x 0-006b: Setting charging current 500
<6>[ 5.253009] android_work: sent uevent USB_STATE=CONFIGURED
<6>[ 5.453226] bq2419x 0-006b: Charging enabled
<4>[ 15.267828] adbd (170): /proc/170/oom_adj is deprecated, please use /proc/170/oom_score_adj instead.
<6>[ 26.198292] bq2419x 0-006b: bq2419x_reset_wdt() from THREAD()
chevyowner said:
kmsg
Code:
sysfs_add_one+0x90/0xb0)
<4>[ 2.102778] [<c017f7fc>] (sysfs_add_one+0x90/0xb0) from [<c017fa54>] (create_dir+0x68/0xc4)
<4>[ 2.102904] [<c017fa54>] (create_dir+0x68/0xc4) from [<c017fdc0>] (sysfs_create_dir+0x6c/0xb0)
<4>[ 2.103123] [<c017fdc0>] (sysfs_create_dir+0x6c/0xb0) from [<c02796cc>] (kobject_add_internal+0xb0/0x278)
<4>[ 2.103359] [<c02796cc>] (kobject_add_internal+0xb0/0x278) from [<c0279ccc>] (kobject_add+0x4c/0x94)
<4>[ 2.103579] [<c0279ccc>] (kobject_add+0x4c/0x94) from [<c0279f34>] (kobject_create_and_add+0x28/0x64)
<4>[ 2.103798] [<c0279f34>] (kobject_create_and_add+0x28/0x64) from [<c03530f0>] (class_compat_register+0x40/0x70)
<4>[ 2.104021] [<c03530f0>] (class_compat_register+0x40/0x70) from [<c052bd4c>] (create_extcon_class+0x54/0x98)
<4>[ 2.104282] [<c052bd4c>] (create_extcon_class+0x54/0x98) from [<c0008674>] (do_one_initcall+0xa0/0x100)
<4>[ 2.104415] [<c0008674>] (do_one_initcall+0xa0/0x100) from [<c0a1b8e4>] (do_initcalls+0x78/0xac)
<4>[ 2.104630] [<c0a1b8e4>] (do_initcalls+0x78/0xac) from [<c0a1b9a8>] (kernel_init+0x90/0x128)
<4>[ 2.104847] [<c0a1b9a8>] (kernel_init+0x90/0x128) from [<c000f8b8>] (kernel_thread_exit+0x0/0x8)
<4>[ 2.105073] ---[ end trace 9d1c79c81885dc7d ]---
<4>[ 2.105207] ------------[ cut here ]------------
<4>[ 2.105329] WARNING: at /home/agrabren/android/roms/cm-10.1/kernel/nvidia/thor/lib/kobject.c:198 kobject_add_internal+0x20c/0x278()
<4>[ 2.105627] kobject_add_internal failed for switch with -EEXIST, don't try to register things with the same name in the same directory.
<4>[ 2.105833] Modules linked in:
<4>[ 2.106061] [<c00159d8>] (unwind_backtrace+0x0/0x140) from [<c006078c>] (warn_slowpath_common+0x54/0x6c)
<4>[ 2.106301] [<c006078c>] (warn_slowpath_common+0x54/0x6c) from [<c0060850>] (warn_slowpath_fmt+0x38/0x48)
<4>[ 2.106526] [<c0060850>] (warn_slowpath_fmt+0x38/0x48) from [<c0279828>] (kobject_add_internal+0x20c/0x278)
<4>[ 2.106662] [<c0279828>] (kobject_add_internal+0x20c/0x278) from [<c0279ccc>] (kobject_add+0x4c/0x94)
<4>[ 2.106888] [<c0279ccc>] (kobject_add+0x4c/0x94) from [<c0279f34>] (kobject_create_and_add+0x28/0x64)
<4>[ 2.107115] [<c0279f34>] (kobject_create_and_add+0x28/0x64) from [<c03530f0>] (class_compat_register+0x40/0x70)
<4>[ 2.107365] [<c03530f0>] (class_compat_register+0x40/0x70) from [<c052bd4c>] (create_extcon_class+0x54/0x98)
<4>[ 2.107589] [<c052bd4c>] (create_extcon_class+0x54/0x98) from [<c0008674>] (do_one_initcall+0xa0/0x100)
<4>[ 2.107809] [<c0008674>] (do_one_initcall+0xa0/0x100) from [<c0a1b8e4>] (do_initcalls+0x78/0xac)
<4>[ 2.107942] [<c0a1b8e4>] (do_initcalls+0x78/0xac) from [<c0a1b9a8>] (kernel_init+0x90/0x128)
<4>[ 2.108165] [<c0a1b9a8>] (kernel_init+0x90/0x128) from [<c000f8b8>] (kernel_thread_exit+0x0/0x8)
<4>[ 2.108397] ---[ end trace 9d1c79c81885dc7e ]---
<4>[ 2.108517] kobject_create_and_add: kobject_add error: -17
<4>[ 2.108728] ------------[ cut here ]------------
<4>[ 2.108856] WARNING: at /home/agrabren/android/roms/cm-10.1/kernel/nvidia/thor/drivers/extcon/extcon_class.c:545 create_extcon_class+0x78/0x98()
<4>[ 2.109071] cannot allocate
<4>[ 2.109291] Modules linked in:
<4>[ 2.109633] [<c00159d8>] (unwind_backtrace+0x0/0x140) from [<c006078c>] (warn_slowpath_common+0x54/0x6c)
<4>[ 2.109855] [<c006078c>] (warn_slowpath_common+0x54/0x6c) from [<c0060850>] (warn_slowpath_fmt+0x38/0x48)
<4>[ 2.110080] [<c0060850>] (warn_slowpath_fmt+0x38/0x48) from [<c052bd70>] (create_extcon_class+0x78/0x98)
<4>[ 2.110229] [<c052bd70>] (create_extcon_class+0x78/0x98) from [<c0008674>] (do_one_initcall+0xa0/0x100)
<4>[ 2.110366] [<c0008674>] (do_one_initcall+0xa0/0x100) from [<c0a1b8e4>] (do_initcalls+0x78/0xac)
<4>[ 2.110588] [<c0a1b8e4>] (do_initcalls+0x78/0xac) from [<c0a1b9a8>] (kernel_init+0x90/0x128)
<4>[ 2.110811] [<c0a1b9a8>] (kernel_init+0x90/0x128) from [<c000f8b8>] (kernel_thread_exit+0x0/0x8)
<4>[ 2.111024] ---[ end trace 9d1c79c81885dc7f ]---
<3>[ 2.117575] mmc0: Command timeout error, intmask: 10001
<3>[ 2.120177] mmc0: Command timeout error, intmask: 10001
<3>[ 2.128564] mmc0: Command timeout error, intmask: 10001
<3>[ 2.131053] mmc0: Command timeout error, intmask: 10001
<3>[ 2.133662] mmc0: Command timeout error, intmask: 10001
<3>[ 2.136144] mmc0: Command timeout error, intmask: 10001
<3>[ 2.138771] mmc0: Command timeout error, intmask: 10001
<3>[ 2.141261] mmc0: Command timeout error, intmask: 10001
<3>[ 2.143847] mmc0: Command timeout error, intmask: 10001
<3>[ 2.146357] mmc0: Command timeout error, intmask: 10001
<3>[ 2.148956] mmc0: Command timeout error, intmask: 10001
<6>[ 2.190251] usb 1-1: new full-speed USB device number 2 using tegra-ehci
<6>[ 2.194790] mmc0: new high speed DDR MMC card at address 0001
<6>[ 2.195114] mmcblk mmc0:0001: Card claimed for testing.
<6>[ 2.195597] mmcblk0: mmc0:0001 MAG2GA 14.5 GiB
<6>[ 2.195952] mmcblk0boot0: mmc0:0001 MAG2GA partition 1 2.00 MiB
<6>[ 2.196412] mmcblk0boot1: mmc0:0001 MAG2GA partition 2 2.00 MiB
<4>[ 2.198299] Primary GPT is invalid, using alternate GPT.
<6>[ 2.198573] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12
<6>[ 2.201579] mmcblk0boot1: unknown partition table
<6>[ 2.202875] mmcblk0boot0: unknown partition table
<6>[ 2.209793] usbcore: registered new interface driver snd-usb-audio
<6>[ 2.217690] usb 1-1: New USB device found, idVendor=0955, idProduct=7203
<6>[ 2.217904] usb 1-1: New USB device strings: Mfr=2, Product=1, SerialNumbe
r=0
<6>[ 2.218111] usb 1-1: Product: NVIDIA Controller v01.01
<6>[ 2.218247] usb 1-1: Manufacturer: NVIDIA Corporation
<6>[ 2.224902] input: NVIDIA Corporation NVIDIA Controller v01.01 as /devices
/platform/tegra-ehci.2/usb1/1-1/1-1:1.0/input/input1
<6>[ 2.225520] generic-usb 0003:0955:7203.0001: input: USB HID v1.11 Gamepad
[NVIDIA Corporation NVIDIA Controller v01.01] on usb-tegra-ehci.2-1/input0
<3>[ 2.239328] mmc1: Command timeout error, intmask: 10001
<3>[ 2.241820] mmc1: Command timeout error, intmask: 10001
<3>[ 2.249889] mmc1: Command timeout error, intmask: 10001
<3>[ 2.252376] mmc1: Command timeout error, intmask: 10001
<3>[ 2.254944] mmc1: Command timeout error, intmask: 10001
<3>[ 2.257427] mmc1: Command timeout error, intmask: 10001
<6>[ 2.302518] mmc1: new high speed SDHC card at address 0001
<6>[ 2.302806] mmcblk mmc1:0001: Card claimed for testing.
<6>[ 2.303312] mmcblk1: mmc1:0001 00000 7.41 GiB
<6>[ 2.318663] mmcblk1: p1
<3>[ 2.354587] mmc2: Command timeout error, intmask: 10001
<3>[ 2.357165] mmc2: Command timeout error, intmask: 10001
<3>[ 2.365554] mmc2: Command timeout error, intmask: 10001
<3>[ 2.368131] mmc2: Command timeout error, intmask: 10001
<3>[ 2.370614] mmc2: Command timeout error, intmask: 10001
<3>[ 2.373095] mmc2: Command timeout error, intmask: 10001
<3>[ 2.375662] mmc2: Command timeout error, intmask: 10001
<3>[ 2.378148] mmc2: Command timeout error, intmask: 10001
<3>[ 2.380963] mmc2: Command timeout error, intmask: 10001
<3>[ 2.383450] mmc2: Command timeout error, intmask: 10001
<3>[ 2.386021] mmc2: Command timeout error, intmask: 10001
<3>[ 2.388537] mmc2: Command timeout error, intmask: 10001
<3>[ 2.427687] mmc2: Command timeout error, intmask: 10001
<3>[ 2.430285] mmc2: Command timeout error, intmask: 10001
<3>[ 2.438654] mmc2: Command timeout error, intmask: 10001
<3>[ 2.441249] mmc2: Command timeout error, intmask: 10001
<3>[ 2.443920] mmc2: Command timeout error, intmask: 10001
<3>[ 2.446509] mmc2: Command timeout error, intmask: 10001
<3>[ 2.449093] mmc2: Command timeout error, intmask: 10001
<3>[ 2.451769] mmc2: Command timeout error, intmask: 10001
<3>[ 2.454360] mmc2: Command timeout error, intmask: 10001
<3>[ 2.457035] mmc2: Command timeout error, intmask: 10001
<3>[ 2.459640] mmc2: Command timeout error, intmask: 10001
<3>[ 2.462330] mmc2: Command timeout error, intmask: 10001
<3>[ 2.501891] mmc2: Command timeout error, intmask: 10001
<3>[ 2.504779] mmc2: Command timeout error, intmask: 10001
<3>[ 2.512863] mmc2: Command timeout error, intmask: 10001
<3>[ 2.515756] mmc2: Command timeout error, intmask: 10001
<3>[ 2.518550] mmc2: Command timeout error, intmask: 10001
<3>[ 2.521430] mmc2: Command timeout error, intmask: 10001
<3>[ 2.524219] mmc2: Command timeout error, intmask: 10001
<3>[ 2.527015] mmc2: Command timeout error, intmask: 10001
<3>[ 2.529899] mmc2: Command timeout error, intmask: 10001
<3>[ 2.532698] mmc2: Command timeout error, intmask: 10001
<3>[ 2.535582] mmc2: Command timeout error, intmask: 10001
<3>[ 2.538387] mmc2: Command timeout error, intmask: 10001
<3>[ 2.578506] mmc2: Command timeout error, intmask: 10001
<3>[ 2.582152] mmc2: Command timeout error, intmask: 10001
<3>[ 2.591476] mmc2: Command timeout error, intmask: 10001
<3>[ 2.594885] mmc2: Command timeout error, intmask: 10001
<3>[ 2.598374] mmc2: Command timeout error, intmask: 10001
<3>[ 2.601774] mmc2: Command timeout error, intmask: 10001
<3>[ 2.605174] mmc2: Command timeout error, intmask: 10001
<3>[ 2.608584] mmc2: Command timeout error, intmask: 10001
<3>[ 2.611994] mmc2: Command timeout error, intmask: 10001
<3>[ 2.615523] mmc2: Command timeout error, intmask: 10001
<3>[ 2.618933] mmc2: Command timeout error, intmask: 10001
<3>[ 2.622461] mmc2: Command timeout error, intmask: 10001
<6>[ 3.016385] tegra-snd-rt5640 tegra-snd-rt5640.0: No speaker regulator found
<6>[ 3.169518] gpio wake49 for gpio=143
<6>[ 3.170052] asoc: rt5640-aif1 <-> tegra30-i2s.1 mapping ok
<6>[ 3.170833] asoc: dit-hifi <-> tegra30-spdif mapping ok
<6>[ 3.171298] asoc: dit-hifi <-> tegra30-i2s.3 mapping ok
<6>[ 3.173150] input: tegra-rt5640 Headphone Jack as /devices/platform/tegra-snd-rt5640.0/sound/card1/input2
<6>[ 3.174472] oprofile: using timer interrupt.
<6>[ 3.174990] GACT probability NOT on
<6>[ 3.175109] Mirror/redirect action on
<6>[ 3.175244] u32 classifier
<6>[ 3.175441] Actions configured
<6>[ 3.175554] Netfilter messages via NETLINK v0.30.
<6>[ 3.175733] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
<6>[ 3.176456] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[ 3.176846] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[ 3.177183] xt_time: kernel timezone is -0000
<6>[ 3.177749] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 3.178186] arp_tables: (C) 2002 David S. Miller
<6>[ 3.178385] TCP: cubic registered
<6>[ 3.178949] NET: Registered protocol family 10
<6>[ 3.180174] Mobile IPv6
<6>[ 3.180352] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 3.180944] IPv6 over IPv4 tunneling driver
<6>[ 3.182282] NET: Registered protocol family 17
<6>[ 3.182420] NET: Registered protocol family 15
<6>[ 3.182626] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 3.183027] NET: Registered protocol family 35
<6>[ 3.183459] NET: Registered protocol family 37
<6>[ 3.183575] NET: Registered protocol family 40
<6>[ 3.185990] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
<5>[ 3.186283] Registering SWP/SWPB emulation handler
<4>[ 3.209333] Disabling clocks left on by bootloader:
<4>[ 3.209454] xusb_hs_src
<4>[ 3.209573] audio_2x
<4>[ 3.209776] audio4_2x
<4>[ 3.209888] audio3_2x
<4>[ 3.210001] audio2_2x
<4>[ 3.210115] audio1_2x
<4>[ 3.210245] audio0_2x
<4>[ 3.210448] audio
<4>[ 3.210558] audio4
<4>[ 3.210839] audio3
<4>[ 3.210949] audio2
<4>[ 3.211058] audio1
<4>[ 3.211270] audio0
<4>[ 3.211458] dsi2-fixed
<4>[ 3.211569] dsi1-fixed
<4>[ 3.211694] uarta_dbg
<4>[ 3.211812] uarta
<4>[ 3.212015] mipi-cal-fixed
<4>[ 3.212125] mipi-cal
<4>[ 3.212258] bsev
<4>[ 3.212390] fuse_burn
<4>[ 3.212511] cclk_lp
<4>[ 3.212624] pll_x_out0
<4>[ 3.212903] pll_u_12M
<4>[ 3.213019] pll_u_60M
<4>[ 3.213135] pll_d2_out0
<4>[ 3.213351] pll_p_out3
<4>[ 3.213469] pll_c_out1
<4>[ 3.213583] pll_m_out1
<6>[ 3.213706] DVFS: Got RTC device name:rtc0
<6>[ 3.215035] palmas-rtc palmas-rtc.3: palmas_rtc_read_time() 113 7 9 4 23 56
<4>[ 3.215506] tegra_dvfs: vdd_cpu: stats above 1390 mV will be squashed
<4>[ 3.216260] tegra_dvfs: vdd_core: stats above 1390 mV will be squashed
<6>[ 3.224846] Tegra CPU DFLL is initialized
<6>[ 3.225222] CPU rate: 613 MHz
<6>[ 3.227088] cpu_dfll cooling device is registered
<6>[ 3.446327] tegra dvfs: tegra sysfs cap interface is initialized
<6>[ 3.446556] tegra dvfs: tegra sysfs floor interface is initialized
<6>[ 3.449424] Core EDP sysfs interface is initialized
<6>[ 3.450850] tegra_actmon.emc: Completed initialization (0)
<6>[ 3.451182] tegra_actmon.avp: Completed initialization (0)
<6>[ 3.453394] vi vi: vi_probe: ++
<6>[ 3.453495] vi vi: tegra_camera_register: ++
<6>[ 3.454851] vi vi: initialized
<4>[ 3.456464] palmas_regen2: incomplete constraints, leaving on
<4>[ 3.458176] palmas_smps12: incomplete constraints, leaving on
<6>[ 3.458964] gpio wake51 for gpio=128
<6>[ 3.459260] gpio wake23 for gpio=69
<6>[ 3.459400] gpio wake27 for gpio=144
<6>[ 3.459793] input: gpio-keys as /devices/platform/gpio-keys.0/input/input3
<6>[ 3.461122] palmas-rtc palmas-rtc.3: palmas_rtc_read_time() 113 7 9 4 23 56
<6>[ 3.461340] palmas-rtc palmas-rtc.3: setting system clock to 2013-08-09 04:23:56 UTC (1376022236)
<6>[ 3.461756] ALSA device list:
<6>[ 3.461852] #0: HDA NVIDIA Tegra at 0x70038000 irq 113
<6>[ 3.462022] #1: tegra-rt5640
<4>[ 3.462159] Warning: unable to open an initial console.
<3>[ 3.465118] init: could not import file '/init.recovery.roth.rc' from '/init.rc'
<3>[ 3.556839] android_usb: already disabled
<3>[ 3.557462] init: Unable to open persistent property directory /data/property errno: 2
<4>[ 3.602852] tegradc tegradc.0: DC doesn't stop at end of frame.
<4>[ 3.856850] tegradc tegradc.0: DC doesn't stop at end of frame.
<3>[ 3.857389] tegradc tegradc.0: DSI pad calibration done
<6>[ 4.463805] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts:
<6>[ 4.610329] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts:
<3>[ 4.616236] android_usb: already disabled
<6>[ 4.618169] adb_open
<6>[ 4.618314] adb_bind_config
<6>[ 4.621974] tegra-udc tegra-udc.0: detected SDP port
<6>[ 4.622095] bq2419x 0-006b: Setting charging current 2
<6>[ 4.729226] android_work: did not send uevent (0 0 (null))
<6>[ 4.765740] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 4.769283] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 4.823241] bq2419x 0-006b: Charging enabled
<6>[ 4.849696] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 4.984224] tegra-udc tegra-udc.0: detected SDP port
<6>[ 4.984350] bq2419x 0-006b: Setting charging current 2
<6>[ 5.124263] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 5.161733] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 5.165407] android_work: sent uevent USB_STATE=DISCONNECTED
<6>[ 5.185224] bq2419x 0-006b: Charging enabled
<6>[ 5.245744] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 5.252164] android_usb gadget: high-speed config #1: android
<6>[ 5.252511] tegra-udc tegra-udc.0: detected SDP port
<6>[ 5.252832] bq2419x 0-006b: Setting charging current 500
<6>[ 5.253009] android_work: sent uevent USB_STATE=CONFIGURED
<6>[ 5.453226] bq2419x 0-006b: Charging enabled
<4>[ 15.267828] adbd (170): /proc/170/oom_adj is deprecated, please use /proc/170/oom_score_adj instead.
<6>[ 26.198292] bq2419x 0-006b: bq2419x_reset_wdt() from THREAD()
Click to expand...
Click to collapse
Thanks for all of this I will attempt it again later this weekend
Edited the ramdisk on the original boot image and...
logcat
pastebin
chevyowner said:
Edited the ramdisk on the original boot image and...
logcat
pastebin
Click to expand...
Click to collapse
Thanks again is there a way to add adb on boot by default? So I can add it to the source
Cool I found the error I just fixed this up in my other nvidia tree for that hisense tablet I really appreciate the log
Unjustified Dev said:
Thanks again is there a way to add adb on boot by default? So I can add it to the source
Cool I found the error I just fixed this up in my other nvidia tree for that hisense tablet I really appreciate the log
Click to expand...
Click to collapse
Yes, but I am to tired to think of it right now but here a zip of the boot.img I modded.
chevyowner said:
Yes, but I am to tired to think of it right now but here a zip of the boot.img I modded.
Click to expand...
Click to collapse
Ok I will find it I fixed those errors I will be back after I wake up
I followed below steps for installing official miui v4 rom to desire s
1. Download official miui v4 stable rom from www.miui.com
2. Format sd card and system (clean format).
3. Hboot is 7.0
4. Installed official chinese sense 3.6 rom and reboot the phone to recovery.
5. factory reset and wipe cache & delvic cache.
My problem is while installing miui v4 3.2.22 stable official version...my installation aborted saying
updating package....
formatting system.......
do not format system.............
installed successfully....
Post reboot HTC splash screen appears for a while and then phone reboots on its own to recovery.
Please help...
talktoraj83 said:
I followed below steps for installing official miui v4 rom to desire s
1. Download official miui v4 stable rom from www.miui.com
2. Format sd card and system (clean format).
3. Hboot is 7.0
4. Installed official chinese sense 3.6 rom and reboot the phone to recovery.
5. factory reset and wipe cache & delvic cache.
My problem is while installing miui v4 3.2.22 stable official version...my installation aborted saying
updating package....
formatting system.......
do not format system.............
installed successfully....
Post reboot HTC splash screen appears for a while and then phone reboots on its own to recovery.
Please help...
Click to expand...
Click to collapse
Flash the boot.img from the ROM.zip through cmd on your PC.
NVardan said:
Flash the boot.img from the ROM.zip through cmd on your PC.
Click to expand...
Click to collapse
But he's on hboot 7.xxx
Shouldn't he be alrd s-off. Op do tell us if you're s-on or off.
Get 4ext. I think there's an image file that u can flash in fastboot mode. Search dev section for the thread.
Wipe everything (except sdcard)
Flash ROM
Reboot into rom
*flash gapps after set up.
FromBeyondThisWorld
#Fear said:
But he's on hboot 7.xxx
Shouldn't he be alrd s-off. Op do tell us if you're s-on or off.
Get 4ext. I think there's an image file that u can flash in fastboot mode. Search dev section for the thread.
Wipe everything (except sdcard)
Flash ROM
Reboot into rom
*flash gapps after set up.
FromBeyondThisWorld
Click to expand...
Click to collapse
You're right. That makes sense. HBOOT 7.xxx is already S-Off (I'm on this hboot too, I didn't notice ). :silly:
#Fear said:
But he's on hboot 7.xxx
Shouldn't he be alrd s-off. Op do tell us if you're s-on or off.
Get 4ext. I think there's an image file that u can flash in fastboot mode. Search dev section for the thread.
Wipe everything (except sdcard)
Flash ROM
Reboot into rom
*flash gapps after set up.
FromBeyondThisWorld
Click to expand...
Click to collapse
Ya my phone is s-off....and had pushed boot.img successfully bufore and after installation of rom.zip file but still same problem..
I think m missing some step....that is specific for flashing miui v4 official rom for desire s
What recovery is on your device? Try using 4ext :thumbup:
1.full wipe(except sdcard)
2.flash rom
3.reboot
Don't flash gapps first and see if it boots.
FromBeyondThisWorld
#Fear said:
What recovery is on your device? Try using 4ext :thumbup:
1.full wipe(except sdcard)
2.flash rom
3.reboot
Don't flash gapps first and see if it boots.
FromBeyondThisWorld
Click to expand...
Click to collapse
No its not booting..i have tried all permutation & combination....
on latest 4ext recovery
talktoraj83 said:
No its not booting..i have tried all permutation & combination....
on latest 4ext recovery
Click to expand...
Click to collapse
There is one hint if it could help some one to find out issue with my installation...
When m trying below patch for formatting my phone gives error..
http://www.androidfilehost.com/?fid=9390189810980749321
talktoraj83 said:
There is one hint if it could help some one to find out issue with my installation...
When m trying below patch for formatting my phone gives error..
http://www.androidfilehost.com/?fid=9390189810980749321
Click to expand...
Click to collapse
This guy had bootloop too when he tried, but he was trying the russian version. He solve it with amidabuddha kernel.
Cheers
#Fear said:
This guy had bootloop too when he tried, but he was trying the russian version. He solve it with amidabuddha kernel.
Cheers
Click to expand...
Click to collapse
Can you confirm that miuiv4 official version rom has kernel inside it or not?
talktoraj83 said:
Can you confirm that miuiv4 official version rom has kernel inside it or not?
Click to expand...
Click to collapse
Just look inside the zip and you`ll know....
Flashing another kernel wouldn`t harm,
if your device isn`t booting anyway...
take a logcat and attach it and/or look inside,
then all`ll become clear...
asgardr said:
Just look inside the zip and you`ll know....
Flashing another kernel wouldn`t harm,
if your device isn`t booting anyway...
take a logcat and attach it and/or look inside,
then all`ll become clear...
Click to expand...
Click to collapse
Please find below logcat-
10.554687] init: untracked pid 1288 exited
<6>[ 10.666137] EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts:
<3>[ 10.779083] EXT3-fs (mmcblk0p25): error: couldn't mount because of unsupported optional features (40)
<3>[ 10.779937] EXT2-fs (mmcblk0p25): error: couldn't mount because of unsupported optional features (40)
<6>[ 10.828582] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts: (null)
<3>[ 10.829498] init: untracked pid 1309 exited
<6>[ 11.487731] pm8058_led_currents_store: bank 6 currents 1
<6>[ 11.487976] pm8058_drvx_led_brightness_set: bank 6 brightness 0
<6>[ 11.488128] pm8058_drvx_led_brightness_set: bank 6 brightness 255
<6>[ 11.488708] pm8058_led_currents_store: bank 6 currents 9
<6>[ 11.488830] pm8058_drvx_led_brightness_set: bank 6 brightness 0
<6>[ 11.489074] pm8058_drvx_led_brightness_set: bank 6 brightness 255
<6>[ 11.490509] pm8058_drvx_led_brightness_set: bank 6 brightness 9
<6>[ 11.491119] pm8058_drvx_led_brightness_set: bank 6 brightness 90
<6>[ 11.491638] pm8058_drvx_led_brightness_set: bank 6 brightness 9
<6>[ 11.492218] pm8058_drvx_led_brightness_set: bank 6 brightness 90
<3>[ 11.875061] init: untracked pid 1343 exited
<6>[ 17.498992] [email protected],236
<6>[ 17.559783] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 17.561279] [ATS][set_vibration][successful]
<6>[ 17.584899] [VIB]vibrator_timer_func
<6>[ 17.663330] [email protected],236
<6>[ 25.172546] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 25.173919] [ATS][set_vibration][successful]
<6>[ 25.197753] [VIB]vibrator_timer_func
<6>[ 34.992889] [BATT] M2A_RPC: set_charging: 0 at 29234003670 (2013-08-30 18:23:52.340426829 UTC)
<6>[ 34.993194] Switch charger OFF
<6>[ 34.994964] [BATT] M2A_RPC: set_charging: 1 at 29236046353 (2013-08-30 18:23:52.342500000 UTC)
<6>[ 34.995269] Switch charger ON (SLOW)
<6>[ 34.996215] batt: Switch charger ON (SLOW): regh 0x03=83
<6>[ 34.997314] [BATT] M2A_RPC: cable_update: USB at 29238332939 (2013-08-30 18:23:52.344847561 UTC)
<6>[ 34.997619] [BATT] htc_cable_status_update: 0 -> 1
<6>[ 34.997741] [USB] msm_hsusb_set_vbus_state: 1
<6>[ 34.997924] [USB] hsusb: OFFLINE -> ONLINE
<6>[ 34.998016] [USB] lpm exit
<6>[ 34.999298] [USB] hsusb: reset controller
<6>[ 35.044311] msm_hsusb_phy_reset
<6>[ 35.189300] [USB] ulpi: write 0x06 to 0x36
<6>[ 35.189392] [USB] ulpi: write 0x0c to 0x31
<6>[ 35.189605] [USB] ulpi: write 0x31 to 0x32
<6>[ 35.189697] [USB] ulpi: write 0x01 to 0x0d
<6>[ 35.189788] [USB] ulpi: write 0x01 to 0x10
<6>[ 35.189971] [USB] handle_notify_offline: notify offline
<6>[ 35.190093] [USB] msm_hsusb: enable pullup
<6>[ 35.193206] [USB] suspend
<6>[ 35.209381] [USB] not AC charger
<6>[ 35.293640] [USB] reset
<6>[ 35.293731] [USB] send connect type 1
<6>[ 35.293853] Touch: cable change to 1
<6>[ 35.295227] fsg_set_ums_state: 1
<6>[ 35.295349] ums: set state 1
<6>[ 35.295745] [BATT] online=1
<6>[ 35.295928] [USB] portchange USB_SPEED_HIGH
<6>[ 35.296112] [BATT] Update SMEM: cable type 1 at 29536839037 (2013-08-30 18:23:52.643353659 UTC)
<6>[ 35.338897] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 35.345031] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<6>[ 35.351470] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 35.357391] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<6>[ 35.484069] android_usb gadget: high speed config #1: android
<6>[ 35.484222] adb_function_set_alt: maxsize = 512
<6>[ 35.484497] ums: set state 1
<6>[ 66.039398] Release 'boot-time' perf_lock
<6>[ 66.620391] Release 'boot-time' no_halt_lock
<6>[ 67.040405] perflock_notifier_call: cpufreq recover policy 245760 1024000
<6>[ 246.697113] [BATT] M2A_RPC: level_update: 68 at 240732143916 (2013-08-30 18:27:23.838079269 UTC)
<6>[ 246.698181] [BATT] power_supply_changed: battery at 240732906111 (2013-08-30 18:27:23.839176830 UTC)
<6>[ 246.718322] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 246.737548] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<3>[ 246.935974] INFO: task audio_mvs:428 blocked for more than 120 seconds.
<3>[ 246.936370] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 246.937011] audio_mvs D c0425f80 0 428 2 0x00000000
<4>[ 246.938323] Backtrace:
<4>[ 246.939056] [<c0425bbc>] (schedule+0x0/0x450) from [<c005101c>] (__msm_rpc_read+0x22c/0xa4c)
<4>[ 246.939758] [<c0050df0>] (__msm_rpc_read+0x0/0xa4c) from [<c0051858>] (msm_rpc_read+0x1c/0x88)
<4>[ 246.940185] [<c005183c>] (msm_rpc_read+0x0/0x88) from [<c0074f34>] (audio_mvs_thread+0x4c/0x164)
<4>[ 246.940856] r6:00000000 r5:c7e69f9c r4:c05ef368
<4>[ 246.942596] [<c0074ee8>] (audio_mvs_thread+0x0/0x164) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 246.942962] r8:00000000 r7:c05ef368 r6:c0074ee8 r5:c7e69fcc r4:c7c1df48
<4>[ 246.945312] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 246.946044] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df48
<3>[ 246.947753] INFO: task krmt_storagecln:460 blocked for more than 120 seconds.
<3>[ 246.948425] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 246.948791] krmt_storagecln D c0425f80 0 460 2 0x00000000
<4>[ 246.950073] Backtrace:
<4>[ 246.950805] [<c0425bbc>] (schedule+0x0/0x450) from [<c004a1c4>] (rpc_clients_cb_thread+0x98/0x1b0)
<4>[ 246.951507] [<c004a12c>] (rpc_clients_cb_thread+0x0/0x1b0) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 246.952239] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 246.952606] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1ddf8
<3>[ 246.954620] INFO: task voice:740 blocked for more than 120 seconds.
<3>[ 246.955261] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 246.955657] voice D c0425f80 0 740 2 0x00000000
<4>[ 246.957031] Backtrace:
<4>[ 246.957763] [<c0425bbc>] (schedule+0x0/0x450) from [<c04266e8>] (schedule_timeout+0x24/0x23c)
<4>[ 246.958465] [<c04266c4>] (schedule_timeout+0x0/0x23c) from [<c04264e0>] (wait_for_common+0x12c/0x1f0)
<4>[ 246.959136] r7:c76f2000 r6:00000002 r5:c05eaf44 r4:7fffffff
<4>[ 246.960876] [<c04263b4>] (wait_for_common+0x0/0x1f0) from [<c0426684>] (wait_for_completion+0x1c/0x20)
<4>[ 246.961578] [<c0426668>] (wait_for_completion+0x0/0x20) from [<c005a38c>] (voice_thread+0x6c/0x554)
<4>[ 246.962280] [<c005a320>] (voice_thread+0x0/0x554) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 246.962707] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 246.963378] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df30
<3>[ 367.073181] INFO: task rpcrouter:274 blocked for more than 120 seconds.
<3>[ 367.073547] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.074249] rpcrouter D c0425f80 0 274 2 0x00000000
<4>[ 367.075286] Backtrace:
<4>[ 367.076354] [<c0425bbc>] (schedule+0x0/0x450) from [<c004f748>] (rr_read+0x178/0x1a4)
<4>[ 367.076751] [<c004f5d0>] (rr_read+0x0/0x1a4) from [<c004f900>] (do_read_data+0x1c/0xa08)
<4>[ 367.077453] [<c004f8e4>] (do_read_data+0x0/0xa08) from [<c00ae168>] (worker_thread+0x18c/0x238)
<4>[ 367.078186] [<c00adfdc>] (worker_thread+0x0/0x238) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.078887] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.079284] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c2bd70
<3>[ 367.081268] INFO: task audio_mvs:428 blocked for more than 120 seconds.
<3>[ 367.081634] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.082305] audio_mvs D c0425f80 0 428 2 0x00000000
<4>[ 367.083679] Backtrace:
<4>[ 367.084381] [<c0425bbc>] (schedule+0x0/0x450) from [<c005101c>] (__msm_rpc_read+0x22c/0xa4c)
<4>[ 367.085052] [<c0050df0>] (__msm_rpc_read+0x0/0xa4c) from [<c0051858>] (msm_rpc_read+0x1c/0x88)
<4>[ 367.085479] [<c005183c>] (msm_rpc_read+0x0/0x88) from [<c0074f34>] (audio_mvs_thread+0x4c/0x164)
<4>[ 367.086151] r6:00000000 r5:c7e69f9c r4:c05ef368
<4>[ 367.087554] [<c0074ee8>] (audio_mvs_thread+0x0/0x164) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.088195] r8:00000000 r7:c05ef368 r6:c0074ee8 r5:c7e69fcc r4:c7c1df48
<4>[ 367.090545] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.090911] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df48
<3>[ 367.092895] INFO: task krmt_storagecln:460 blocked for more than 120 seconds.
<3>[ 367.093627] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.093994] krmt_storagecln D c0425f80 0 460 2 0x00000000
<4>[ 367.095336] Backtrace:
<4>[ 367.096038] [<c0425bbc>] (schedule+0x0/0x450) from [<c004a1c4>] (rpc_clients_cb_thread+0x98/0x1b0)
<4>[ 367.096771] [<c004a12c>] (rpc_clients_cb_thread+0x0/0x1b0) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.097442] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.097808] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1ddf8
<3>[ 367.099822] INFO: task voice:740 blocked for more than 120 seconds.
<3>[ 367.100189] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 367.100860] voice D c0425f80 0 740 2 0x00000000
<4>[ 367.102203] Backtrace:
<4>[ 367.102905] [<c0425bbc>] (schedule+0x0/0x450) from [<c04266e8>] (schedule_timeout+0x24/0x23c)
<4>[ 367.103637] [<c04266c4>] (schedule_timeout+0x0/0x23c) from [<c04264e0>] (wait_for_common+0x12c/0x1f0)
<4>[ 367.104034] r7:c76f2000 r6:00000002 r5:c05eaf44 r4:7fffffff
<4>[ 367.106018] [<c04263b4>] (wait_for_common+0x0/0x1f0) from [<c0426684>] (wait_for_completion+0x1c/0x20)
<4>[ 367.106750] [<c0426668>] (wait_for_completion+0x0/0x20) from [<c005a38c>] (voice_thread+0x6c/0x554)
<4>[ 367.107452] [<c005a320>] (voice_thread+0x0/0x554) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 367.107849] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 367.108520] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df30
<6>[ 486.697143] [BATT] M2A_RPC: level_update: 69 at 480497997575 (2013-08-30 18:31:23.603963416 UTC)
<6>[ 486.699218] [BATT] power_supply_changed: battery at 480500162209 (2013-08-30 18:31:23.606036587 UTC)
<6>[ 486.718139] pm8058_pwm_led_brightness_set: bank 0 brightness 0
<6>[ 486.737762] pm8058_pwm_led_brightness_set: bank 1 brightness 1
<3>[ 487.220397] INFO: task audio_mvs:428 blocked for more than 120 seconds.
<3>[ 487.221069] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 487.221466] audio_mvs D c0425f80 0 428 2 0x00000000
<4>[ 487.222778] Backtrace:
<4>[ 487.223541] [<c0425bbc>] (schedule+0x0/0x450) from [<c005101c>] (__msm_rpc_read+0x22c/0xa4c)
<4>[ 487.224243] [<c0050df0>] (__msm_rpc_read+0x0/0xa4c) from [<c0051858>] (msm_rpc_read+0x1c/0x88)
<4>[ 487.224945] [<c005183c>] (msm_rpc_read+0x0/0x88) from [<c0074f34>] (audio_mvs_thread+0x4c/0x164)
<4>[ 487.225341] r6:00000000 r5:c7e69f9c r4:c05ef368
<4>[ 487.227020] [<c0074ee8>] (audio_mvs_thread+0x0/0x164) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 487.227691] r8:00000000 r7:c05ef368 r6:c0074ee8 r5:c7e69fcc r4:c7c1df48
<4>[ 487.229736] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 487.230468] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df48
<3>[ 487.232208] INFO: task krmt_storagecln:460 blocked for more than 120 seconds.
<3>[ 487.232879] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 487.233551] krmt_storagecln D c0425f80 0 460 2 0x00000000
<4>[ 487.234588] Backtrace:
<4>[ 487.235290] [<c0425bbc>] (schedule+0x0/0x450) from [<c004a1c4>] (rpc_clients_cb_thread+0x98/0x1b0)
<4>[ 487.235992] [<c004a12c>] (rpc_clients_cb_thread+0x0/0x1b0) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 487.236694] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 487.237365] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1ddf8
<3>[ 487.239044] INFO: task voice:740 blocked for more than 120 seconds.
<3>[ 487.239715] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
<6>[ 487.240081] voice D c0425f80 0 740 2 0x00000000
<4>[ 487.241485] Backtrace:
<4>[ 487.242187] [<c0425bbc>] (schedule+0x0/0x450) from [<c04266e8>] (schedule_timeout+0x24/0x23c)
<4>[ 487.242889] [<c04266c4>] (schedule_timeout+0x0/0x23c) from [<c04264e0>] (wait_for_common+0x12c/0x1f0)
<4>[ 487.243560] r7:c76f2000 r6:00000002 r5:c05eaf44 r4:7fffffff
<4>[ 487.245269] [<c04263b4>] (wait_for_common+0x0/0x1f0) from [<c0426684>] (wait_for_completion+0x1c/0x20)
<4>[ 487.245971] [<c0426668>] (wait_for_completion+0x0/0x20) from [<c005a38c>] (voice_thread+0x6c/0x554)
<4>[ 487.246673] [<c005a320>] (voice_thread+0x0/0x554) from [<c00b1f28>] (kthread+0x84/0x8c)
<4>[ 487.247375] [<c00b1ea4>] (kthread+0x0/0x8c) from [<c009e9a0>] (do_exit+0x0/0x6ac)
<4>[ 487.247772] r7:00000013 r6:c009e9a0 r5:c00b1ea4 r4:c7c1df30
<6>[ 491.649566] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 491.650665] [ATS][set_vibration][successful]
<6>[ 491.674682] [VIB]vibrator_timer_func
<6>[ 492.960632] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 492.961486] [ATS][set_vibration][successful]
<6>[ 492.985748] [VIB]vibrator_timer_func
<6>[ 494.228454] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 494.229370] [ATS][set_vibration][successful]
<6>[ 494.253662] [VIB]vibrator_timer_func
<6>[ 494.353851] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts:
<6>[ 505.722808] EXT4-fs (mmcblk0p27): mounted filesystem with ordered data mode. Opts:
<6>[ 507.874176] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 507.875091] [ATS][set_vibration][successful]
<6>[ 507.899688] [VIB]vibrator_timer_func
<6>[ 510.369537] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 510.370391] [ATS][set_vibration][successful]
<6>[ 510.394653] [VIB]vibrator_timer_func
<6>[ 512.736968] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 512.738128] [ATS][set_vibration][successful]
<6>[ 512.762573] [VIB]vibrator_timer_func
<6>[ 514.352325] Touch: calibration confirm
<6>[ 514.373626] Touch Status: 0x01 0x10 0x77 0xA1 0x0A
<6>[ 514.381561] Touch Status: 0x01 0x00 0x77 0xA1 0x0A
<6>[ 514.776885] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 514.777862] [ATS][set_vibration][successful]
<6>[ 514.802093] [VIB]vibrator_timer_func
<6>[ 519.868621] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 519.869506] [ATS][set_vibration][successful]
<6>[ 519.893737] [VIB]vibrator_timer_func
<6>[ 522.455322] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 522.456207] [ATS][set_vibration][successful]
<6>[ 522.480499] [VIB]vibrator_timer_func
<6>[ 523.943817] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 523.944732] [ATS][set_vibration][successful]
<6>[ 523.969024] [VIB]vibrator_timer_func
<6>[ 529.148071] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 529.149322] [ATS][set_vibration][successful]
<6>[ 529.173309] [VIB]vibrator_timer_func
<6>[ 536.841979] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 536.843017] [ATS][set_vibration][successful]
<6>[ 536.867218] [VIB]vibrator_timer_func
<6>[ 543.078704] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 543.079650] [ATS][set_vibration][successful]
<6>[ 543.103851] [VIB]vibrator_timer_func
<6>[ 546.098419] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 546.099304] [ATS][set_vibration][successful]
<6>[ 546.123565] [VIB]vibrator_timer_func
<6>[ 547.273925] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 547.274871] [ATS][set_vibration][successful]
<6>[ 547.299133] [VIB]vibrator_timer_func
<6>[ 549.013427] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 549.014587] [ATS][set_vibration][successful]
<6>[ 549.038635] [VIB]vibrator_timer_func
<6>[ 550.455963] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 550.456909] [ATS][set_vibration][successful]
<6>[ 550.481201] [VIB]vibrator_timer_func
<6>[ 551.694274] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 551.695129] [ATS][set_vibration][successful]
<6>[ 551.719390] [VIB]vibrator_timer_func
<6>[ 562.994323] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 562.995758] [ATS][set_vibration][successful]
<6>[ 563.019470] [VIB]vibrator_timer_func
<6>[ 569.194122] [VIB] recovery(parent:recovery): vibrates 25 msec
<6>[ 569.195098] [ATS][set_vibration][successful]
<6>[ 569.219329] [VIB]vibrator_timer_func
<6>[ 569.385711] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts:
<3>[ 569.644683] tc: version magic '2.6.35.10 preempt mod_unload ARMv7 ' should be '2.6.35.10-g13f6602 preempt mod_unload ARMv7 '
<6>[ 572.967926] EXT4-fs (mmcblk0p25): mounted filesystem with ordered data mode. Opts:
<3>[ 573.057800] EXT3-fs (mmcblk0p28): error: couldn't mount because of unsupported optional features (40)
<3>[ 573.058654] EXT2-fs (mmcblk0p28): error: couldn't mount because of unsupported optional features (40)
<6>[ 573.118988] EXT4-fs (mmcblk0p28): mounted filesystem with ordered data mode. Opts: (null)
<3>[ 573.575347] EXT3-fs (mmcblk0p29): error: couldn't mount because of unsupported optional features (240)
<3>[ 573.576202] EXT2-fs (mmcblk0p29): error: couldn't mount because of unsupported optional features (240)
<4>[ 573.578399] EXT4-fs (mmcblk0p29): warning: checktime reached, running e2fsck is recommended
<6>[ 573.636688] EXT4-fs (mmcblk0p29): mounted filesystem without journal. Opts: (null)
<6>[ 606.694824] [BATT] M2A_RPC: set_charging: 100 at 600378089037 (2013-08-30 18:33:23.484603659 UTC)
<6>[ 606.695129] Switch charger CHECK
<6>[ 606.695495] TPS65200 STATUS_A27
I´m to late... But extract attached folder and push the folder in the ROM.zip ...
It´s a fix
Some lines are wrong in updater-script
Hey,
I've got a rooted Nexus 5 with android 4.4.3 on it.
on the past monthes it sggested me to OTA update but i knew that because of the root I'm not allowed to do it and ignored.
Yesterday, when I took my nexus out of my pocket it was stuck on boot screen (Google with open lock sign).
After some resaerch I realised that it might possible that it was open in my pocket and accidently OTA updta.
Now my situation is:
* Stuck on boot screen
* Can get to recovery but it says that I've encrypted my system.
* When charging - no charging screen
* Tried to manual flash rom/recovery/bootloade/baseband with fastboot and got error (flash write error)
* When opening shell I can clearly distinguish that some mounts are missing (like system...)
* Unable to factory reset / wipe anything.
Please if you got a clue how can I solve it write it down
Updates (For future googlers) :
* Tried to unplug the battery and plug it back but it didn't help...
Thanks alot,
Yaniv.
This situation can definitely occur with a bad flash / OTA. Unfortunately, all you can do is go into TWRP and do a full factory reset and wipe everything. Then boot into the bootloader and run flash-all in the factory image.
I forgot to mention that I'm unable to factory reset/wipe anything (I get the unable to mount problem)
I think that maybe my mass storage chip has fried
Your emmc is dead... Get a replacement.
Yes it seems like my emmc is the problem.
anyway, Jtag could be a good solution here?
and if not, someone knows where I could find 32GB emmc chip? I searched in ebay and couldn't find...
hbhc123 said:
Yes it seems like my emmc is the problem.
anyway, Jtag could be a good solution here?
and if not, someone knows where I could find 32GB emmc chip? I searched in ebay and couldn't find...
Click to expand...
Click to collapse
you dont find it.
RMA it or buy a new one.
New Information
I suspect that this is not the case of fried emmc:
When I am using adb shell and entering the command:
dmesg | grep mmc
I am getting this output:
Code:
<3>[ 120.178121] mmcblk0: error -110 transferring data, sector 193621, nr 11, cmd response 0x900, card status 0x0
<3>[ 120.346008] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 120.346053] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 120.346912] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 120.346980] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 120.349140] mmcblk0: error -110 transferring data, sector 193622, nr 10, cmd response 0x900, card status 0x0
<3>[ 120.517024] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 120.517100] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 120.517965] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 120.518004] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 120.520164] mmcblk0: error -110 transferring data, sector 193623, nr 9, cmd response 0x900, card status 0x0
<3>[ 120.520250] Buffer I/O error on device mmcblk0p16, logical block 10
<3>[ 120.693458] mmc1: data txfr (0x00100000) error: -110 after 168 ms
<6>[ 120.693503] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 120.694361] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 120.694430] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 120.698601] mmcblk0: error -110 transferring data, sector 193624, nr 264,cmd response 0x900, card status 0x80b00
<4>[ 120.698683] mmcblk0: retrying using single block read
<3>[ 120.891913] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 120.891959] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 120.892836] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 120.892906] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 120.895069] mmcblk0: error -110 transferring data, sector 193728, nr 160,
cmd response 0x900, card status 0x0
<3>[ 121.062998] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 121.063242] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 121.068251] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 121.068472] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 121.071373] mmcblk0: error -110 transferring data, sector 193729, nr 159,
cmd response 0x900, card status 0x0
<3>[ 121.239703] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 121.239778] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 121.240639] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 121.240678] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 121.242870] mmcblk0: error -110 transferring data, sector 193730, nr 158,cmd response 0x900, card status 0x0
<3>[ 121.242987] end_request: I/O error, dev mmcblk0, sector 193730
<3>[ 121.410834] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 121.410907] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 121.411762] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 121.411831] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 121.414189] mmcblk0: error -110 transferring data, sector 193731, nr 157,cmd response 0x900, card status 0x0
<3>[ 121.414330] end_request: I/O error, dev mmcblk0, sector 193731
<3>[ 121.582213] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 121.582624] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 121.587435] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 121.587653] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 121.589886] mmcblk0: error -110 transferring data, sector 193732, nr 156,cmd response 0x900, card status 0x0
<3>[ 121.590326] end_request: I/O error, dev mmcblk0, sector 193732
<3>[ 121.758806] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 121.758880] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 121.759745] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 121.759783] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 121.761942] mmcblk0: error -110 transferring data, sector 193733, nr 155,cmd response 0x900, card status 0x0
<3>[ 121.762020] end_request: I/O error, dev mmcblk0, sector 193733
<3>[ 121.929940] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 121.929986] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 121.930848] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 121.930917] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 121.933110] mmcblk0: error -110 transferring data, sector 193734, nr 154,cmd response 0x900, card status 0x0
<3>[ 121.933189] end_request: I/O error, dev mmcblk0, sector 193734
<3>[ 122.101069] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 122.101114] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 122.101971] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 122.102040] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 122.104232] mmcblk0: error -110 transferring data, sector 193735, nr 153,cmd response 0x900, card status 0x0
<3>[ 122.104311] end_request: I/O error, dev mmcblk0, sector 193735
<3>[ 122.272162] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 122.272238] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 122.273068] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 122.273137] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 122.275294] mmcblk0: error -110 transferring data, sector 193736, nr 152,cmd response 0x900, card status 0x0
<3>[ 122.275373] end_request: I/O error, dev mmcblk0, sector 193736
<3>[ 122.443221] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 122.443298] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 122.444167] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 122.444204] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 122.446392] mmcblk0: error -110 transferring data, sector 193737, nr 151,cmd response 0x900, card status 0x0
<3>[ 122.446439] end_request: I/O error, dev mmcblk0, sector 193737
<3>[ 122.614316] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 122.614391] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 122.615250] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 122.615288] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 122.617445] mmcblk0: error -110 transferring data, sector 193738, nr 150,cmd response 0x900, card status 0x0
<3>[ 122.617524] end_request: I/O error, dev mmcblk0, sector 193738
<3>[ 122.785407] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 122.785453] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 122.786280] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 122.786349] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 122.788521] mmcblk0: error -110 transferring data, sector 193739, nr 149,cmd response 0x900, card status 0x0
<3>[ 122.788601] end_request: I/O error, dev mmcblk0, sector 193739
<3>[ 122.956481] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 122.956526] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 122.957381] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 122.957450] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 122.959617] mmcblk0: error -110 transferring data, sector 193740, nr 148,
cmd response 0x900, card status 0x0
<3>[ 123.127503] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 123.127546] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 123.128411] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 123.128450] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 123.130607] mmcblk0: error -110 transferring data, sector 193741, nr 147,cmd response 0x900, card status 0x0
<3>[ 123.298494] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 123.298595] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 123.299771] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 123.299824] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 123.302086] mmcblk0: error -110 transferring data, sector 193742, nr 146,cmd response 0x900, card status 0x0
<3>[ 123.469989] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 123.470298] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 123.473777] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 123.474068] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 123.476694] mmcblk0: error -110 transferring data, sector 193743, nr 145,cmd response 0x900, card status 0x0
<3>[ 123.644900] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 123.644944] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 123.645807] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 123.645875] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 123.648032] mmcblk0: error -110 transferring data, sector 193744, nr 144,cmd response 0x900, card status 0x0
<3>[ 123.815945] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 123.816358] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 123.821177] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 123.821395] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 123.823278] mmcblk0: error -110 transferring data, sector 193745, nr 143,cmd response 0x900, card status 0x0
<3>[ 123.991606] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 123.991681] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 123.992504] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 123.992543] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 123.994788] mmcblk0: error -110 transferring data, sector 193746, nr 142,cmd response 0x900, card status 0x0
<3>[ 124.162675] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 124.162721] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 124.163582] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 124.163651] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 124.165809] mmcblk0: error -110 transferring data, sector 193747, nr 141,cmd response 0x900, card status 0x0
<3>[ 124.333693] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 124.333738] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 124.334596] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 124.334665] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 124.336823] mmcblk0: error -110 transferring data, sector 193748, nr 140,cmd response 0x900, card status 0x0
<3>[ 124.504709] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 124.504784] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 124.505640] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 124.505678] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 124.507868] mmcblk0: error -110 transferring data, sector 193749, nr 139,cmd response 0x900, card status 0x0
<3>[ 124.675724] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 124.675800] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 124.676631] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 124.676700] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 124.678858] mmcblk0: error -110 transferring data, sector 193750, nr 138,cmd response 0x900, card status 0x0
<3>[ 124.846744] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 124.846818] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 124.847678] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 124.847716] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 124.849903] mmcblk0: error -110 transferring data, sector 193751, nr 137,cmd response 0x900, card status 0x0
<3>[ 125.017757] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 125.017761] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 125.017814] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 125.017818] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 125.020858] mmcblk0: error -110 transferring data, sector 193752, nr 136,cmd response 0x900, card status 0x0
<3>[ 125.188680] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 125.188724] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 125.189577] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 125.189646] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 125.191804] mmcblk0: error -110 transferring data, sector 193753, nr 135,cmd response 0x900, card status 0x0
<3>[ 125.359701] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 125.359799] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 125.361823] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 125.361911] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 125.364322] mmcblk0: error -110 transferring data, sector 193754, nr 134,cmd response 0x900, card status 0x0
<3>[ 125.532330] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 125.532403] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 125.533269] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 125.533308] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 125.535495] mmcblk0: error -110 transferring data, sector 193755, nr 133,cmd response 0x900, card status 0x0
<3>[ 125.703380] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 125.703423] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 125.704278] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 125.704348] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 125.706507] mmcblk0: error -110 transferring data, sector 193756, nr 132,cmd response 0x900, card status 0x0
<3>[ 125.874419] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 125.874656] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 125.879448] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 125.879833] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 125.882717] mmcblk0: error -110 transferring data, sector 193757, nr 131,cmd response 0x900, card status 0x0
<3>[ 126.051047] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 126.051123] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 126.051981] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 126.052018] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 126.054233] mmcblk0: error -110 transferring data, sector 193758, nr 130,cmd response 0x900, card status 0x0
<3>[ 126.222119] mmc1: data txfr (0x00100000) error: -110 after 167 ms
<6>[ 126.222194] sdhci: =========== REGISTER DUMP (mmc1)===========
<6>[ 126.223057] mmc1: clk: 200000000 clk-gated: 0 claimer: mmcqd/1 pwr: 10
<6>[ 126.223127] mmc1: rpmstatus[pltfm](runtime-suspend:usage_count:disable_depth)(0:0:0)
<3>[ 126.225287] mmcblk0: error -110 transferring data, sector 193759, nr 129,cmd response 0x900, card status 0x0
<3>[ 126.261253] mmcblk0: mmc_blk_err_check: general error sending status command, card status 0x80900
<4>[ 126.261299] mmcblk0: retrying write for general error
<3>[ 126.261720] mmcblk0: mmc_blk_err_check: general error sending status command, card status 0x80900
<4>[ 126.261790] mmcblk0: retrying write for general error
<3>[ 126.262178] mmcblk0: mmc_blk_err_check: general error sending status command, card status 0x80900
<4>[ 126.262246] mmcblk0: retrying write for general error
<3>[ 126.262637] mmcblk0: mmc_blk_err_check: general error sending status command, card status 0x80900
<4>[ 126.262706] mmcblk0: retrying write for general error
<3>[ 126.263125] mmcblk0: mmc_blk_err_check: general error sending status command, card status 0x80900
<4>[ 126.263165] mmcblk0: retrying write for general error
<3>[ 126.263586] mmcblk0: mmc_blk_err_check: general error sending status command, card status 0x80900
<4>[ 126.263656] mmcblk0: retrying write for general error
<3>[ 126.263703] Buffer I/O error on device mmcblk0p16, logical block 11
<4>[ 126.263773] lost page write due to I/O error on mmcblk0p16
<3>[ 126.263822] Buffer I/O error on device mmcblk0p16, logical block 12
<4>[ 126.263890] lost page write due to I/O error on mmcblk0p16
<3>[ 126.264078] EXT4-fs (mmcblk0p16): error loading journal
<7>[ 126.304383] SELinux: initialized (dev mmcblk0p1, type vfat), uses genfs_contexts
By referrence to this post:
http://forum.xda-developers.com/showthread.php?t=1284196
I am not getting any line with one of the following:
Code:
mmc0: failed to get card ready
mmc0: reinit card
mmc0: Starting deferred resume
mmc0: Deferred resume failed
If anyone have any inputs it would be helpful
"mount":
Code:
rootfs on / type rootfs (rw)
tmpfs on /dev type tmpfs (rw,seclabel,nosuid,relatime,mode=755)
devpts on /dev/pts type devpts (rw,seclabel,relatime,mode=600)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,seclabel,relatime)
selinuxfs on /sys/fs/selinux type selinuxfs (rw,relatime)
Looks like all your partitions are erroring. Needs replacing
Edit... Well you certainly at least have an issue with /persist. There's a guide to fix that in my signature.
Not sure that will be enough though
Sent from my Nexus 5 using Tapatalk
Do not use recovery or fastboot then, flash stock rom with lg's bootloader. (Hold volume up + plug in usb)
Sent from my Nexus 5 using Tapatalk
What do you mean by "flash stock rom with lg's bootloader"?
Is it an app for computer?.. If you could give somemore explanation / link for a thread in subject it would be great.
rootSU said:
Looks like all your partitions are erroring. Needs replacing
Edit... Well you certainly at least have an issue with /persist. There's a guide to fix that in my signature.
Not sure that will be enough though
Sent from my Nexus 5 using Tapatalk
Click to expand...
Click to collapse
Is it possible to do the same solution to the system partition?
("e2fsck /dev/block/platform/msm_sdcc.1/by-name/system")
hbhc123 said:
What do you mean by "flash stock rom with lg's bootloader"?
Is it an app for computer?.. If you could give somemore explanation / link for a thread in subject it would be great.
Click to expand...
Click to collapse
Maybe he means with lg flashtool and download mode. Again, link in my signature. However you should try and fix persist first as per my post.
Sent from my Nexus 5 using Tapatalk
hbhc123 said:
What do you mean by "flash stock rom with lg's bootloader"?
Is it an app for computer?.. If you could give somemore explanation / link for a thread in subject it would be great.
Click to expand...
Click to collapse
He means flash stock factory image, if that doesn't work or save you then RMA is the key
Well, RMA is not option for me...
#rootSU:
is it possible to use this solution for system partition?
(using "e2fsck /dev/block/platform/msm_sdcc.1/by-name/system")
Hello.
could you please help me to flash my device ?
it’s a RK30** based device (maybe a RK3066).
I have yet tested a lot of possibility….. but now way to flash a custom recovery ;-(
I would like install TWRP or CWM
I tested :
Arctools.apk (don’t work) / room manager (don’t work) / a batch tool adb installer (don’t work) / fastboot in bootloader mode (don’t work_no device detected) / directly flash some update.zip from the original recovery (don’t work).
My device is rooted buit nothing work for me.
I tried also to flash diferent recovery.img from RKFLASHKIT (ubuntu inside ).
so…. i’m a little bit lost.
For security I dumped these originals partitions :
misc.img
recovery.img
boot.img
kernel.img
I can also provide a complete dmesg in a second post.
So, I hope you will be able to help me to find a good version of recovery and the good way to flash it !
I thank you in advance !
dmseg 1/2
<6>[ 0.000000] Initializing cgroup subsys cpu
<5>[ 0.000000] Linux version 3.0.8+ ([email protected]) (gcc version 4.4.3 (GCC) ) #233 SMP PREEMPT Mon Sep 2 18:37:15 CST 2013
<4>[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7d
<4>[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
<4>[ 0.000000] Machine: RK30board
<6>[ 0.000000] memory reserve: Memory(base:0x91800000 size:80M) reserved for <ion>
<6>[ 0.000000] memory reserve: Memory(base:0x90c00000 size:12M) reserved for <fb0 buf>
<6>[ 0.000000] memory reserve: Memory(base:0x90600000 size:6M) reserved for <camera_ipp_mem>
<6>[ 0.000000] memory reserve: Total reserved 98M
<4>[ 0.000000] Memory policy: ECC disabled, Data cache writeback
<6>[ 0.000000] bootconsole [earlycon0] enabled
<4>[ 0.000000] CPU SRAM: copied sram code from c0aa7000 to fef00100 – fef023d0
<4>[ 0.000000] CPU SRAM: copied sram data from c0aa92d0 to fef03000 – fef03920
<6>[ 0.000000] L310 cache controller enabled
<6>[ 0.000000] l2x0: 16 ways, CACHE_ID 0x4100c0c8, AUX_CTRL 0x76050001, Cache size: 524288 B
<4>[ 0.000000] DDR DEBUG: version 1.00 20130121
<4>[ 0.000000] DDR DEBUG: DDR3 Device
<4>[ 0.000000] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
<4>[ 0.000000] DDR DEBUG: init success!!! freq=300MHz
<4>[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90
<4>[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90
<4>[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90
<4>[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=90
<4>[ 0.000000] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
<4>[ 0.000000] DDR DEBUG: DRV Pull-Up=0xb, DRV Pull-Dwn=0xb
<4>[ 0.000000] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
<4>[ 0.000000] rk30_iomux_init
<4>[ 0.000000] Boot mode: 6 flag: 0xc3524200
<7>[ 0.000000] On node 0 totalpages: 237056
<7>[ 0.000000] free_area_init_node: node 0, pgdat c0aa6340, node_mem_map c152d000
<7>[ 0.000000] Normal zone: 1744 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 196400 pages, LIFO batch:31
<7>[ 0.000000] HighMem zone: 304 pages used for memmap
<7>[ 0.000000] HighMem zone: 38608 pages, LIFO batch:7
<6>[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1d35000 s7072 r8192 d13408 u32768
<7>[ 0.000000] pcpu-alloc: s7072 r8192 d13408 u32768 alloc=8*4096
<7>[ 0.000000] pcpu-alloc: [0] 0 [0] 1
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 235008
<5>[ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x00180000 mtdparts=rk29xxnand:[email protected](misc),[email protected](kernel),[email protected](boot),[email protected](recovery),[email protected](backup),[email protected](cache),[email protected](userdata),[email protected](kpanic),[email protected](system),[email protected](user) bootver=2013-06-20#1.34 firmware_ver=4.1.1
<6>[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 0.000000] Memory: 774MB 152MB = 926MB total
<5>[ 0.000000] Memory: 920020k/920020k available, 128556k reserved, 155648K highmem
<5>[ 0.000000] Virtual kernel memory layout:
<5>[ 0.000000] vector : 0xffff0000 – 0xffff1000 ( 4 kB)
<5>[ 0.000000] fixmap : 0xfff00000 – 0xfffe0000 ( 896 kB)
<5>[ 0.000000] DMA : 0xffc00000 – 0xffe00000 ( 2 MB)
<5>[ 0.000000] vmalloc : 0xf7000000 – 0xfe800000 ( 120 MB)
<5>[ 0.000000] lowmem : 0xc0000000 – 0xf6800000 ( 872 MB)
<5>[ 0.000000] pkmap : 0xbfe00000 – 0xc0000000 ( 2 MB)
<5>[ 0.000000] modules : 0xbf000000 – 0xbfe00000 ( 14 MB)
<5>[ 0.000000] .init : 0xc0408000 – 0xc048d000 ( 532 kB)
<5>[ 0.000000] .text : 0xc048d000 – 0xc0a411cc (5841 kB)
<5>[ 0.000000] .data : 0xc0a42000 – 0xc0aa6e60 ( 404 kB)
<5>[ 0.000000] .bss : 0xc0aaa024 – 0xc152c388 (10761 kB)
<6>[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
<6>[ 0.000000] Preemptible hierarchical RCU implementation.
<6>[ 0.000000] NR_IRQS:416
<4>[ 0.000000] rk30_gpio_init: 176 gpio irqs in 6 banks
<6>[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
<6>[ 0.000000] Console: colour dummy device 80×30
<6>[ 0.004965] Calibrating delay loop (skipped) preset value.. 1631.46 BogoMIPS (lpj=8157341)
<6>[ 0.013833] pid_max: default: 32768 minimum: 301
<6>[ 0.019037] Mount-cache hash table entries: 512
<6>[ 0.024581] Initializing cgroup subsys debug
<6>[ 0.029240] Initializing cgroup subsys cpuacct
<6>[ 0.034099] Initializing cgroup subsys freezer
<6>[ 0.038983] CPU: Testing write buffer coherency: ok
<4>[ 0.145025] CPU1: Booted secondary processor
<6>[ 0.145071] Brought up 2 CPUs
<6>[ 0.152997] SMP: Total of 2 processors activated (3262.93 BogoMIPS).
<6>[ 0.160214] devtmpfs: initialized
<6>[ 0.171372] NET: Registered protocol family 16
<4>[ 0.176259] last_log: 0xf0100000 0xc0aae210
<4>[ 0.182918] ————[ cut here ]————
<4>[ 0.187958] WARNING: at drivers/gpio/gpiolib.c:101 gpio_ensure_requested+0x48/0x114()
<4>[ 0.196340] autorequest GPIO-183
<4>[ 0.199929] [<c04981c4>] (unwind_backtrace+0x0/0xf0) from [<c04c0ae0>] (warn_slowpath_common+0x4c/0x64)
<4>[ 0.210067] [<c04c0ae0>] (warn_slowpath_common+0x4c/0x64) from [<c04c0b78>] (warn_slowpath_fmt+0x2c/0x3c)
<4>[ 0.220438] [<c04c0b78>] (warn_slowpath_fmt+0x2c/0x3c) from [<c061a4f0>] (gpio_ensure_requested+0x48/0x114)
<4>[ 0.230984] [<c061a4f0>] (gpio_ensure_requested+0x48/0x114) from [<c061aba0>] (gpio_direction_output+0x7c/0xfc)
<4>[ 0.241938] [<c061aba0>] (gpio_direction_output+0x7c/0xfc) from [<c040e444>] (machine_rk30_board_init+0x34/0x288)
<4>[ 0.252985] [<c040e444>] (machine_rk30_board_init+0x34/0x288) from [<c040a4d8>] (customize_machine+0x1c/0x28)
<4>[ 0.263713] [<c040a4d8>] (customize_machine+0x1c/0x28) from [<c048d5d8>] (do_one_initcall+0x94/0x164)
<4>[ 0.273604] [<c048d5d8>] (do_one_initcall+0x94/0x164) from [<c0408350>] (kernel_init+0x88/0x130)
<4>[ 0.283027] [<c0408350>] (kernel_init+0x88/0x130) from [<c0493678>] (kernel_thread_exit+0x0/0x8)
<4>[ 0.292464] —[ end trace 1b75b31a2719ed1c ]—
<6>[ 0.398156] rk29sdk_wifi_bt_gpio_control_init: init finished
<6>[ 0.408723] console [ttyFIQ0] enabled, bootconsole disabled
<6>[ 0.414889] Registered FIQ tty driver f008fc00
<6>[ 0.426987] bio: create slab <bio-0> at 0
<4>[ 0.431222] wm831x_dcdc_init
<4>[ 0.431404] wm831x_ldo_init
<5>[ 0.431758] SCSI subsystem initialized
<6>[ 0.431971] usbcore: registered new interface driver usbfs
<6>[ 0.432043] usbcore: registered new interface driver hub
<6>[ 0.434252] usbcore: registered new device driver usb
<6>[ 0.434711] rk30_i2c rk30_i2c.0: i2c-0: RK30 I2C adapter
<6>[ 0.434938] rk30_i2c rk30_i2c.1: i2c-1: RK30 I2C adapter
<6>[ 0.435151] rk30_i2c rk30_i2c.2: i2c-2: RK30 I2C adapter
<6>[ 0.435260] rk30_i2c rk30_i2c.3: i2c-3: RK30 I2C adapter
<6>[ 0.435379] rk30_i2c rk30_i2c.4: i2c-4: RK30 I2C adapter
<6>[ 0.483138] rk30-adc rk30-adc: rk30 adc: driver initialized
<4>[ 0.483433] timed_gpio_probe
<6>[ 0.483524] Advanced Linux Sound Architecture Driver Version 1.0.24.
<6>[ 0.483920] Bluetooth: Core ver 2.16
<6>[ 0.483970] NET: Registered protocol family 31
<6>[ 0.483982] Bluetooth: HCI device and connection manager initialized
<6>[ 0.483999] Bluetooth: HCI socket layer initialized
<6>[ 0.484011] Bluetooth: L2CAP socket layer initialized
<6>[ 0.484036] Bluetooth: SCO socket layer initialized
<4>[ 0.485072] rk fb probe ok!
<4>[ 0.485164] wm831x_i2c_init
<6>[ 0.532516] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 0.884439] rk30_i2c rk30_i2c.1: Addr[0x34] wait event timeout, state: 0, is_busy: 1, error: 0, complete_what: 0x0, ipd: 0x0
<4>[ 0.904437] rk30_i2c rk30_i2c.1: I2C_CON: start bit is set
<3>[ 0.924437] wm831x 1-0034: Failed to read parent ID: -110
<4>[ 0.924461] wm831x: probe of 1-0034 failed with error -110
<3>[ 1.324439] rk30_i2c rk30_i2c.1: Addr[0x2d] wait event timeout, state: 0, is_busy: 1, error: 0, complete_what: 0x2, ipd: 0x20
<3>[ 1.364436] tps65910 1-002d: tps65910_set_bits:read from reg 3f failed
<3>[ 1.764438] rk30_i2c rk30_i2c.1: Addr[0x2d] wait event timeout, state: 0, is_busy: 1, error: 0, complete_what: 0x2, ipd: 0x20
<3>[ 1.804436] tps65910 1-002d: read from reg 46 failed
<3>[ 1.804451] tps65910 1-002d: Error in configuring external control EN1
<4>[ 1.804465] tps65910 1-002d: Failed to initialise ext control config
<3>[ 2.204439] rk30_i2c rk30_i2c.1: Addr[0x2d] wait event timeout, state: 0, is_busy: 1, error: 0, complete_what: 0x2, ipd: 0x20
<3>[ 2.244436] tps65910 1-002d: tps65910_set_bits:read from reg 20 failed
<3>[ 2.244453] set_machine_constraints: VIO: failed to enable
<3>[ 2.244515] tps65910 1-002d: failed to register tps65910-pmic regulator
<4>[ 2.244536] tps65910-pmic: probe of tps65910-pmic failed with error -110
<4>[ 2.244680] tps65910_pre_init,line=38
<3>[ 2.644440] rk30_i2c rk30_i2c.1: Addr[0x2d] wait event timeout, state: 0, is_busy: 1, error: 0, complete_what: 0x2, ipd: 0x20
<3>[ 2.684437] tps65910 1-002d: Read from reg 0x40 failed
<3>[ 2.684451] Unable to read TPS65910_DEVCTRL2 reg
<3>[ 2.684463] tps65910 1-002d: pre_init() failed: -110
<4>[ 2.684601] tps65910: probe of 1-002d failed with error -110
<6>[ 2.684808] Switching to clocksource timer1
<4>[ 2.685016] lcdc0:reg_phy_base = 0x1010c000,reg_vir_base:0xf701c000
<4>[ 2.685049] fb0:win1
<4>[ 2.685052] fb1:win0
<4>[ 2.685056] fb2:win2
<6>[ 2.685065] Switched to NOHz mode on CPU #1
<4>[ 2.685153] lcdc0: dclk:33000000>>fps:59 rk30_load_screen for lcdc0 ok!
<6>[ 2.694437] Switched to NOHz mode on CPU #0
<4>[ 2.713630] fb0hy:90c00000>>vir:f8000000>>len:0xc00000
<4>[ 2.713896] rk_fb_register>>>>>fb0
<4>[ 2.714053] rk_fb_register>>>>>fb1
<4>[ 2.714227] rk_fb_register>>>>>fb2
<4>[ 2.714240] lcdc0 wakeup from stanby
<6>[ 2.714250] lcdc0 win1 open
<4>[ 2.731799] rk30 lcdc0 probe ok!
<4>[ 2.731858] lcdc1:reg_phy_base = 0x1010e000,reg_vir_base:0xf7028000
<4>[ 2.731891] fb0:win1
<4>[ 2.731895] fb1:win0
<4>[ 2.731898] fb2:win2
<4>[ 2.731952] lcdc1: dclk:74250000>>fps:60 rk30_load_screen for lcdc1 ok!
<4>[ 2.731974] fb3hy:90c00000>>vir:f8000000>>len:0xc00000
<4>[ 2.732253] rk_fb_register>>>>>fb3
<4>[ 2.732420] rk_fb_register>>>>>fb4
<4>[ 2.732568] rk_fb_register>>>>>fb5
<4>[ 2.732579] rk30 lcdc1 probe ok!
<4>[ 2.732637] ————————————————-boot with some other pmu,this is important notify————————————————-pwm_regulator_probe:n_voltages=17
<4>[ 2.732844] pwm_regulator.0: driver initialized
<4>[ 2.732856] rk30 pwm regulator is ok with pmu tps65910
<4>[ 2.742902] pwm_regulator_probe set vdd_core=1100000mV end
<4>[ 2.870731] regbase f7080000 0x0, otg_phy_confed08184, 0x550
<6>[ 2.920980] rk30_adc_battery: driver initialized
<6>[ 2.921245] NET: Registered protocol family 2
<6>[ 2.921372] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[ 2.921722] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
<6>[ 2.923559] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
<6>[ 2.924621] TCP: Hash tables configured (established 131072 bind 65536)
<6>[ 2.924635] TCP reno registered
<6>[ 2.924648] UDP hash table entries: 512 (order: 2, 16384 bytes)
<6>[ 2.924687] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
<6>[ 2.925056] NET: Registered protocol family 1
<4>[ 2.925231] RK29 Backlight Driver Initialized.
<6>[ 2.925425] Unpacking initramfs…
<6>[ 3.000775] Freeing initrd memory: 1536K
<6>[ 3.000973] rk30-tsadc rk30-tsadc: initialized
<6>[ 3.001830] Loaded driver for PL330 DMAC-1 rk29-pl330
<6>[ 3.001847] DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
<6>[ 3.002002] Loaded driver for PL330 DMAC-2 rk29-pl330
<6>[ 3.002017] DBUFF-64x8bytes Num_Chans-7 Num_Peri-20 Num_Events-14
<4>[ 3.009188] highmem bounce pool size: 64 pages
<6>[ 3.009376] ashmem: initialized
<6>[ 3.014384] fuse init (API version 7.16)
<6>[ 3.015969] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
<6>[ 3.015988] io scheduler noop registered
<6>[ 3.015998] io scheduler deadline registered
<6>[ 3.016056] io scheduler cfq registered (default)
<6>[ 3.022108] rga: Driver loaded succesfully
<4>[ 3.022746] rk_serial.c v1.3 2012-12-14
<6>[ 3.022838] rk_serial.0: ttyS0 at MMIO 0x10124000 (irq = 66) is a rk29_serial.0
<6>[ 3.044916] rk_serial rk_serial.0: membase 0xf704c000
<6>[ 3.044980] rk_serial.3: ttyS3 at MMIO 0x20068000 (irq = 69) is a rk29_serial.3
<6>[ 3.084869] rk_serial rk_serial.3: membase 0xf7050000
<6>[ 3.085144] Rockchip ion module(version: 1.0) is successfully loaded
<6>[ 3.087680] loop: module loaded
<6>[ 3.087788] Android kernel panic handler initialized (bind=kpanic)
<6>[ 3.088503] PPP generic driver version 2.4.2
<6>[ 3.088688] PPP Deflate Compression module registered
<6>[ 3.088701] PPP BSD Compression module registered
<6>[ 3.089295] PPP MPPE Compression module registered
<6>[ 3.089311] NET: Registered protocol family 24
<6>[ 3.089390] usbcore: registered new interface driver asix
<6>[ 3.089440] usbcore: registered new interface driver cdc_ether
<6>[ 3.089486] usbcore: registered new interface driver dm9620
<6>[ 3.089532] usbcore: registered new interface driver SR9700_android
<6>[ 3.089577] usbcore: registered new interface driver net1080
<6>[ 3.089621] usbcore: registered new interface driver cdc_subset
<6>[ 3.089674] usbcore: registered new interface driver zaurus
<6>[ 3.089697] cdc_ncm: 04-Aug-2011
<6>[ 3.089741] usbcore: registered new interface driver cdc_ncm
<4>[ 3.089753] Rockchip WiFi SYS interface (V1.00) …
<6>[ 3.089797] Initializing USB Mass Storage driver…
<6>[ 3.089858] usbcore: registered new interface driver usb-storage
<6>[ 3.089870] USB Mass Storage support registered.
<6>[ 3.089988] usbcore: registered new interface driver usbserial
<6>[ 3.090033] USB Serial support registered for generic
<6>[ 3.090086] usbcore: registered new interface driver usbserial_generic
<6>[ 3.090099] usbserial: USB Serial Driver core
<6>[ 3.090139] USB Serial support registered for GSM modem (1-port)
<6>[ 3.090193] usbcore: registered new interface driver option
<6>[ 3.090205] option: v0.7.2:USB Driver for GSM modems
<6>[ 3.300992] DWC_OTG: ^^^^^^^^^^^^^^^^^Device Mode
<6>[ 3.301017] usb20_otg usb20_otg: DWC OTG Controller
<6>[ 3.301042] usb20_otg usb20_otg: new USB bus registered, assigned bus number 1
<6>[ 3.301072] usb20_otg usb20_otg: irq 48, io mem 0x00000000
<6>[ 3.301081] DWC_OTG: dwc_otg_hcd_start controller in device mode,everest
<6>[ 3.301128] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 3.301141] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 3.301151] usb usb1: Product: DWC OTG Controller
<6>[ 3.301159] usb usb1: Manufacturer: Linux 3.0.8+ dwc_otg_hcd
<6>[ 3.301167] usb usb1: SerialNumber: usb20_otg
<6>[ 3.301501] hub 1-0:1.0: USB hub found
<6>[ 3.301516] hub 1-0:1.0: 1 port detected
<6>[ 3.302100] DWC_OTG: host20_driver_probe host2.0 reg addr: 0x101c0000 remap:0xf7180000
<6>[ 3.512773] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode
<6>[ 3.512796] usb20_host usb20_host: DWC OTG Controller
<6>[ 3.512818] usb20_host usb20_host: new USB bus registered, assigned bus number 2
<6>[ 3.512845] usb20_host usb20_host: irq 49, io mem 0x00000000
<6>[ 3.512887] DWC_OTG: Init: Port Power? op_state=1
<6>[ 3.512895] DWC_OTG: Init: Power Port (0)
<6>[ 3.512933] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 3.512945] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 3.512955] usb usb2: Product: DWC OTG Controller
<6>[ 3.512963] usb usb2: Manufacturer: Linux 3.0.8+ host20_hcd
<6>[ 3.512971] usb usb2: SerialNumber: usb20_host
<6>[ 3.513248] hub 2-0:1.0: USB hub found
<6>[ 3.513263] hub 2-0:1.0: 1 port detected
<6>[ 3.514441] android_usb gadget: Mass Storage Function, version: 2009/09/11
<6>[ 3.514453] android_usb gadget: Number of LUNs=2
<6>[ 3.514462] lun0: LUN: removable file: (no medium)
<6>[ 3.514471] lun1: LUN: removable file: (no medium)
<6>[ 3.514625] android_usb gadget: android_usb ready
<6>[ 3.514812] input: rk29-keypad as /devices/platform/rk29-keypad/input/input0
<4>[ 3.515006] ==gsl_ts_init==
<4>[ 3.515038] GSLX680 Enter gsl_ts_probe
<4>[ 3.515045] ==kzalloc success=
<4>[ 3.515051] [GSLX680] Enter gslX680_ts_init
<6>[ 3.515241] input: gslX680 as /devices/platform/rk30_i2c.2/i2c-2/2-0040/input/input1
<4>[ 3.605422] I read reg 0xf0 is 0
<4>[ 3.625190] I write reg 0xf0 0x12
<4>[ 3.645345] I read reg 0xf0 is 0x12
<3>[ 3.645687] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 2…
<3>[ 3.646027] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 1…
<3>[ 3.646366] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 0…
<3>[ 3.745366] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 2…
<3>[ 3.745875] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 1…
<3>[ 3.746372] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 0…
dmesg 2/2
<4>[ 3.814895] =============gsl_load_fw start==============
<6>[ 3.894947] usb 2-1: new high speed USB device number 2 using usb20_host
<6>[ 4.105961] usb 2-1: New USB device found, idVendor=0bda, idProduct=0179
<6>[ 4.106033] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 4.106081] usb 2-1: Product: 802.11n NIC
<6>[ 4.106116] usb 2-1: Manufacturer: Realtek
<6>[ 4.106150] usb 2-1: SerialNumber: 00AE0E0372CD
<4>[ 4.489292] =============gsl_load_fw end==============
<3>[ 4.535378] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 2…
<3>[ 4.535938] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 1…
<3>[ 4.536452] i2c i2c-2: No ack, Maybe slave(addr: 0x40) not exist or abnormal power-on, retry 0…
<4>[ 4.695988] [GSLX680] End gsl_ts_probe
<4>[ 4.696156] ret=0
<4>[ 4.696796] sensor_register_slave:mxc6225,id=16
<4>[ 4.696838] sensor_register_slave:akm8975,id=18
<4>[ 4.697136] sensor_register_slave:l3g4200d,id=31
<4>[ 4.697175] sensor_register_slave:cm3217,id=34
<4>[ 4.697205] light_cm3217_init
<6>[ 4.698522] lirc_dev: IR Remote Control driver registered, major 250
<6>[ 4.698568] IR NEC protocol handler initialized
<6>[ 4.698600] IR RC5(x) protocol handler initialized
<6>[ 4.698632] IR RC6 protocol handler initialized
<6>[ 4.698662] IR JVC protocol handler initialized
<6>[ 4.698693] IR Sony protocol handler initialized
<6>[ 4.698724] IR RC5 (streamzap) protocol handler initialized
<6>[ 4.698758] IR LIRC bridge handler initialized
<6>[ 4.698787] Linux video capture interface: v2.00
<4>[ 4.699398] start_charge_logo_display
<6>[ 4.700715] device-mapper: uevent: version 1.0.3
<6>[ 4.701579] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected]
<6>[ 4.702357] Bluetooth: HCI UART driver ver 2.2
<6>[ 4.702401] Bluetooth: HCI H4 protocol initialized
<6>[ 4.702436] Bluetooth: HCILL protocol initialized
<6>[ 4.702976] cpuidle: using governor ladder
<6>[ 4.703016] cpuidle: using governor menu
<6>[ 4.709081]
<6>[ 4.709092] drivers/mmc/core/core.c…1827.. ===== mmc_rescan Begin….[mmc0]
<6>[ 4.714321] rk29_sdmmc_change_clk_div..1928.. newDiv=83, newCLK=298Khz [sd_mmc]
<6>[ 4.714545] .Line3891..The End of SDMMC-probe Ver.5.00 The last modify date is 2012-11-05. [sd_mmc]
<6>[ 4.715141] .Line3891..The End of SDMMC-probe Ver.5.00 The last modify date is 2012-11-05. [sdio]
<7>[ 4.715296] Registered led device: button-backlight
<6>[ 4.717070] usbcore: registered new interface driver usbhid
<6>[ 4.717084] usbhid: USB HID core driver
<6>[ 4.717456] logger: created 256K log ‘log_main’
<6>[ 4.717551] logger: created 256K log ‘log_events’
<6>[ 4.717660] logger: created 256K log ‘log_radio’
<6>[ 4.717755] logger: created 256K log ‘log_system’
<4>[ 4.718339] i2c-core: driver [ES8323] using legacy suspend method
<4>[ 4.718354] i2c-core: driver [ES8323] using legacy resume method
<6>[ 4.718541] ES8323 audio_card_init
<6>[ 4.718553] XXXXEnter::audio_card_init—-201
<4>[ 4.718789] es8323_probe
<6>[ 4.751094]
<6>[ 4.751098] mmc_attach_sd..1218.. ===== Begin to identify card as SD-card. [mmc0]
<3>[ 4.757661] ES8323 0-0010: Failed to add route Left DAC->Left Mixer
<3>[ 4.757708] ES8323 0-0010: ES8323.0-0010: Failed to add 3D Mode: -16
<3>[ 4.757805] ES8323 0-0010: Failed to add route Left DAC->Left Mixer
<6>[ 4.757821] Enter::rk29_es8323_init—-138
<6>[ 4.757833] Enter::es8323_set_dai_sysclk—-668
<3>[ 4.767002] ES8323 0-0010: asoc: failed to add kcontrol Left Line Mux
<3>[ 4.767030] ES8323 0-0010: asoc: failed to add kcontrol Right PGA Mux
<3>[ 4.767056] ES8323 0-0010: asoc: failed to add kcontrol Left PGA Mux
<3>[ 4.767079] ES8323 0-0010: asoc: failed to add kcontrol Right ADC Mux
<3>[ 4.767102] ES8323 0-0010: asoc: failed to add kcontrol Left ADC Mux
<3>[ 4.767126] ES8323 0-0010: asoc: failed to add kcontrol Differential Mux
<4>[ 4.767178] ES8323 0-0010: ASoC: Failed to create POST debugfs file
<4>[ 4.767197] ES8323 0-0010: ASoC: Failed to create PRE debugfs file
<4>[ 4.767214] ES8323 0-0010: ASoC: Failed to create RINPUT2 debugfs file
<4>[ 4.767229] ES8323 0-0010: ASoC: Failed to create RINPUT1 debugfs file
<4>[ 4.767245] ES8323 0-0010: ASoC: Failed to create LINPUT2 debugfs file
<4>[ 4.767261] ES8323 0-0010: ASoC: Failed to create LINPUT1 debugfs file
<4>[ 4.767276] ES8323 0-0010: ASoC: Failed to create VREF debugfs file
<4>[ 4.767292] ES8323 0-0010: ASoC: Failed to create ROUT2 debugfs file
<4>[ 4.767307] ES8323 0-0010: ASoC: Failed to create LOUT2 debugfs file
<4>[ 4.767323] ES8323 0-0010: ASoC: Failed to create ROUT1 debugfs file
<4>[ 4.767338] ES8323 0-0010: ASoC: Failed to create LOUT1 debugfs file
<4>[ 4.767354] ES8323 0-0010: ASoC: Failed to create Left Out 1 debugfs file
<4>[ 4.767370] ES8323 0-0010: ASoC: Failed to create Right Out 1 debugfs file
<4>[ 4.767387] ES8323 0-0010: ASoC: Failed to create Left Out 2 debugfs file
<4>[ 4.767403] ES8323 0-0010: ASoC: Failed to create Right Out 2 debugfs file
<4>[ 4.767420] ES8323 0-0010: ASoC: Failed to create Right Mixer debugfs file
<4>[ 4.767437] ES8323 0-0010: ASoC: Failed to create Left Mixer debugfs file
<4>[ 4.767453] ES8323 0-0010: ASoC: Failed to create Left ADC debugfs file
<4>[ 4.767469] ES8323 0-0010: ASoC: Failed to create Right ADC debugfs file
<4>[ 4.767487] ES8323 0-0010: ASoC: Failed to create Right Line Mux debugfs file
<3>[ 4.767507] ES8323 0-0010: asoc: failed to add kcontrol Left Line Mux
<4>[ 4.767524] ES8323 0-0010: ASoC: Failed to create Left Line Mux debugfs file
<3>[ 4.767543] ES8323 0-0010: asoc: failed to add kcontrol Right PGA Mux
<4>[ 4.767560] ES8323 0-0010: ASoC: Failed to create Right PGA Mux debugfs file
<3>[ 4.767578] ES8323 0-0010: asoc: failed to add kcontrol Left PGA Mux
<4>[ 4.767595] ES8323 0-0010: ASoC: Failed to create Left PGA Mux debugfs file
<3>[ 4.767613] ES8323 0-0010: asoc: failed to add kcontrol Right ADC Mux
<4>[ 4.767629] ES8323 0-0010: ASoC: Failed to create Right ADC Mux debugfs file
<3>[ 4.767648] ES8323 0-0010: asoc: failed to add kcontrol Left ADC Mux
<4>[ 4.767664] ES8323 0-0010: ASoC: Failed to create Left ADC Mux debugfs file
<3>[ 4.767683] ES8323 0-0010: asoc: failed to add kcontrol Differential Mux
<4>[ 4.767700] ES8323 0-0010: ASoC: Failed to create Differential Mux debugfs file
<4>[ 4.767717] ES8323 0-0010: ASoC: Failed to create Mic Bias debugfs file
<6>[ 4.767829] Enter::es8323_set_bias_level—-929 level =1
<6>[ 4.769588] Enter::es8323_set_bias_level—-929 level =2
<6>[ 4.772469] Enter::es8323_set_bias_level—-929 level =3
<6>[ 4.772557] asoc: ES8323 HiFi <-> rk29_i2s.0 mapping ok
<6>[ 4.773027] ALSA device list:
<6>[ 4.773039] #0: RK29_ES8323
<6>[ 4.773144] GACT probability NOT on
<6>[ 4.773159] Mirror/redirect action on
<6>[ 4.773170] u32 classifier
<6>[ 4.773177] Actions configured
<6>[ 4.773188] Netfilter messages via NETLINK v0.30.
<6>[ 4.773244] nf_conntrack version 0.5.0 (14399 buckets, 57596 max)
<6>[ 4.773738] ctnetlink v0.93: registering with nfnetlink.
<6>[ 4.773784] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[ 4.773798] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[ 4.774051] xt_time: kernel timezone is -0000
<6>[ 4.774217] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 4.774402] arp_tables: (C) 2002 David S. Miller
<6>[ 4.774583] TCP cubic registered
<6>[ 4.775165] NET: Registered protocol family 10
<6>[ 4.775970] Mobile IPv6
<6>[ 4.776012] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 4.776160] IPv6 over IPv4 tunneling driver
<6>[ 4.777191] NET: Registered protocol family 17
<6>[ 4.777233] NET: Registered protocol family 15
<5>[ 4.777362] Bridge firewalling registered
<6>[ 4.779331] rk29_sdmmc_change_clk_div..1928.. newDiv=0, newCLK=49500Khz [sd_mmc]
<6>[ 4.779449] mmc0: new high speed SDHC card at address b368
<6>[ 4.779773] Bluetooth: RFCOMM TTY layer initialized
<6>[ 4.779795] Bluetooth: RFCOMM socket layer initialized
<6>[ 4.779807] Bluetooth: RFCOMM ver 1.11
<6>[ 4.779819] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[ 4.779831] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 4.779981] NET: Registered protocol family 35
<6>[ 4.780261] [BT_RFKILL]: Enter rfkill_rk_init
<6>[ 4.780369] [BT_RFKILL]: Request irq for bt wakeup host
<6>[ 4.780396] [BT_RFKILL]: ** disable irq
<6>[ 4.780591] mmcblk0: mmc0:b368 NCard 7.40 GiB
<6>[ 4.781886]
<6>[ 4.781890] msdos_partition..461… ==== Begin to parse sdcard-partition. [mmc0]
<6>[ 4.781908] msdos_partition..530… ==== The sdcard has MBR. [mmc0]
<6>[ 4.781923] msdos_partition..543… ==== partition-1, size=7760896KB [mmc0]
<6>[ 4.781938] msdos_partition..571… ==== main partition-1….[mmc0]
<6>[ 4.781951] mmcblk0: p1
<6>[ 4.782370] mmc_rescan_try_freq..1721.. ===== Initialize SD-card successfully. [mmc0]
<6>[ 4.782396]
<6>[ 4.782399] drivers/mmc/core/core.c…1827.. ===== mmc_rescan Begin….[mmc1]
<6>[ 4.806820] [BT_RFKILL]: bt shut off power
<6>[ 4.836600] [BT_RFKILL]: bt_default device registered.
<6>[ 4.836844] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
<6>[ 4.837495] i2c i2c-0: sensor_probe: ak8975,0xf00a7a00
<4>[ 4.837649] rk30-camera version: v0.2.28 Zoom by ipp
<3>[ 4.837799] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 2…
<3>[ 4.838078] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 1…
<3>[ 4.838349] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 0…
<3>[ 4.838625] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 2…
<3>[ 4.838897] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 1…
<3>[ 4.839169] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 0…
<3>[ 4.839441] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 2…
<3>[ 4.839720] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 1…
<4>[ 4.839907] get cif ldo failed!
<3>[ 4.840023] i2c i2c-0: No ack, Maybe slave(addr: 0xd) not exist or abnormal power-on, retry 0…
<4>[ 4.840042] sensor_chip_init:fail to read ak8975 devid:0xff
<3>[ 4.840057] i2c i2c-0: sensor_probe failed -11
<4>[ 4.840076] sensors: probe of 0-000d failed with error -11
<6>[ 4.840107] i2c i2c-0: sensor_probe: l3g4200d_gryo,0xf00a7c00
<3>[ 4.842697] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 2…
<3>[ 4.842985] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 1…
<3>[ 4.843264] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 0…
<3>[ 4.843543] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 2…
<3>[ 4.843818] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 1…
<3>[ 4.844093] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 0…
<3>[ 4.844369] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 2…
<3>[ 4.844644] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 1…
<3>[ 4.844916] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 0…
<4>[ 4.844934] sensor_chip_init:fail to read l3g4200d_gryo devid:0xff
<3>[ 4.844949] i2c i2c-0: sensor_probe failed -11
<4>[ 4.844968] sensors: probe of 0-0069 failed with error -11
<6>[ 4.844997] i2c i2c-0: sensor_probe: gs_mxc6225,0xf00a7e00
<4>[ 4.845025] sensor_chip_init:gs_mxc6225:devid=0x0,ops=0xc0a8e1f0
<6>[ 4.846097] input: gsensor as /devices/platform/rk30_i2c.0/i2c-0/0-0015/input/input2
<4>[ 4.846242] sensor_irq_init:use polling,delay=30 ms
<4>[ 4.846386] sensor_misc_device_register:miscdevice: mma8452_daemon
<4>[ 4.846402] sensor_probe:initialized ok,sensor name:mxc6225,type:1,id=16
<4>[ 4.846408]
<6>[ 4.846444] i2c i2c-2: sensor_probe: light_cm3217,0xf01be600
<4>[ 4.846460] sensor_chip_init:light_cm3217:devid=0x0,ops=0xc0a8e430
<3>[ 4.846642] i2c i2c-2: No ack, Maybe slave(addr: 0x10) not exist or abnormal power-on, retry 2…
<3>[ 4.846816] i2c i2c-2: No ack, Maybe slave(addr: 0x10) not exist or abnormal power-on, retry 1…
<3>[ 4.846984] i2c i2c-2: No ack, Maybe slave(addr: 0x10) not exist or abnormal power-on, retry 0…
<3>[ 4.847152] i2c i2c-2: No ack, Maybe slave(addr: 0x10) not exist or abnormal power-on, retry 2…
<3>[ 4.847318] i2c i2c-2: No ack, Maybe slave(addr: 0x10) not exist or abnormal power-on, retry 1…
<3>[ 4.847483] i2c i2c-2: No ack, Maybe slave(addr: 0x10) not exist or abnormal power-on, retry 0…
<4>[ 4.847499] sensor_active:fail to active sensor
<4>[ 4.847510] sensor_init:line=97,error
<4>[ 4.847519] sensor_initial:fail to init sensor
<4>[ 4.847529] sensor_chip_init:fail to init sensor
<3>[ 4.847541] i2c i2c-2: sensor_probe failed -11
<4>[ 4.847558] sensors: probe of 2-0010 failed with error -11
<6>[ 4.847610] sensor_init: Probe name sensors
<3>[ 4.847624] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
<6>[ 4.847897] Freeing init memory: 532K
<3>[ 4.862918] init: /init.rk30board.rc: 91: invalid command ‘mknod’
<3>[ 4.863016] init: /init.rk30board.rc: 126: invalid service name ‘mt6620_supplicant’
<4>[ 4.863861] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
<6>[ 4.928007] keychord: using input dev rk29-keypad for fevent
<3>[ 4.928234] init: cannot open ‘/initlogo.rle’
<4>[ 4.947233] get cif ldo failed!
<4>[ 4.947248] Probe gc2035_back success
<4>[ 4.947375] get cif ldo failed!
<4>[ 5.020185] gp_rknand_info = : 0xf02b1000
<4>[ 5.020277] rk30_chip_set:0
<4>[ 5.020359] request IRQ_NANDC irq , ret=0………
<4>[ 5.020387] FTL INFO:Version = 438,Date = 20130620
<4>[ 5.020459] FlashCopyProgBuf1=0xc13d0000
<4>[ 5.020489] ATime: 40 ns AHB: 148 timming: 1081
<4>[ 5.020507] No.1 FLASH INFO:2c 44 44 4b a9
<4>[ 5.020872] ATime: 32 ns AHB: 148 timming: 1061
<4>[ 5.021053] ATime: 32 ns AHB: 148 timming: 1061
<4>[ 5.021066] randomizer = 2 , EccBits = 28 pSpec->pReadRetrial = bf009708
<4>[ 5.054950] get cif ldo failed!
<4>[ 5.054963] Probe gc0308_front success
<4>[ 5.082747] totalLogicBlkRaw = 1897
<4>[ 5.082770] gBootMedia = 1 gSdmmcFwPartOffset =0!
<4>[ 5.082782] rknand_buffer.c version: 4.38 20121130!
<5>[ 5.087176] 10 cmdlinepart partitions found on MTD device rk29xxnand
<5>[ 5.087193] Creating 10 MTD partitions on “rk29xxnand”:
<5>[ 5.087210] 0x000000400000-0x000000800000 : “misc”
<5>[ 5.088284] 0x000000800000-0x000001000000 : “kernel”
<5>[ 5.089072] 0x000001000000-0x000002000000 : “boot”
<5>[ 5.089752] 0x000002000000-0x000004000000 : “recovery”
<5>[ 5.090466] 0x000004000000-0x000008000000 : “backup”
<5>[ 5.091215] 0x000008000000-0x000010000000 : “cache”
<5>[ 5.092032] 0x000010000000-0x000050000000 : “userdata”
<5>[ 5.093836] 0x000050000000-0x000050400000 : “kpanic”
<6>[ 5.095276] apanic: Bound to mtd partition ‘kpanic’
<6>[ 5.095290] apanic: No panic data available
<5>[ 5.095312] 0x000050400000-0x000082400000 : “system”
<5>[ 5.097001] 0x000082400000-0x0000ed200000 : “user”
<4>[ 5.099583] startBlk = 80 sysProtAddr = 79
<6>[ 5.196238] EXT4-fs (mtdblock8): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>[ 5.438596] EXT4-fs (mtdblock6): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<6>[ 5.582263] EXT4-fs (mtdblock5): mounted filesystem with ordered data mode. Opts: noauto_da_alloc
<4>[ 5.588042] UMP: Using OS memory backend, allocation limit: 536870912
<4>[ 5.588064] UMP: UMP device driver loaded
<4>[ 5.623372] Mali: init_mali_clock mali_clock c0a5f900
<4>[ 5.638950] Mali: [MENTION=5839521 [MENTION=1065870 [user=1879310]@@@@[/user][/MENTION][/MENTION]@Mali device driver loaded success [MENTION=5839521 [MENTION=1065870 [user=1879310]@@@@[/user][/MENTION][/MENTION]@
<4>[ 5.639758] rk29_ipp: module is from the staging directory, the quality is unknown, you have been warned.
<4>[ 5.643932] ipp irq 47
<4>[ 5.644762] IPP init, version rk30-ipp 1.003
<4>[ 5.670171] mirroring: Unknown symbol video_data_to_mirroring (err 0)
<4>[ 5.670233] mirroring: Unknown symbol audio_data_to_mirroring (err 0)
<3>[ 5.892652] init: skipping insecure file ‘/data/local.prop’
<3>[ 6.040235] init: cannot find ‘/system/vendor/bin/pvrsrvctl’, disabling ‘pvrsrvctl’
<3>[ 6.051610] init: cannot find ‘/system/etc/install-recovery.sh’, disabling ‘flash_recovery’
<3>[ 6.062798] init: cannot find ‘/system/bin/hald’, disabling ‘hald’
<4>[ 6.102956] vpu: power on
<6>[ 6.105653] VPU_SERVICE: checking hw id 4831
<4>[ 6.110654] vpu: power off…done
<6>[ 6.114009] VPU_SERVICE: init success
<3>[ 6.154931] init: property ‘ro.serialno’ doesn’t exist while expanding ‘${ro.serialno}’
<3>[ 6.162994] init: cannot expand ‘${ro.serialno}’ while writing to ‘/sys/class/android_usb/android0/iSerial’
<3>[ 6.173234] init: using deprecated syntax for specifying property ‘ro.product.usbfactory’, use ${name} instead
<6>[ 6.215694] .409.. MMC0 receive the message sd-No-Media from VOLD.[sd_mmc]
<6>[ 6.215721] .440.. MMC0 receive the message No-Media from VOLD. waitTimes=0 [sd_mmc]
<6>[ 6.308052] .409.. MMC0 receive the message sd-Pending from VOLD.[sd_mmc]
<6>[ 6.310821] .409.. MMC0 receive the message sd-Idle-Unmounted from VOLD.[sd_mmc]
<4>[ 6.311330] [rknand_sys_storage_ioctl:90] rknand_sys_storage_ioctl in
<4>[ 6.311347] [rknand_sys_storage_ioctl:103] RKNAND_GET_DRM_KEY
<4>[ 6.311362] [rknand_sys_storage_ioctl:365] return ret = 0
<3>[ 6.311893] android_usb: already disabled
<6>[ 6.325727] adb_open
<3>[ 8.189655] gc2035 sensor_ioctl cmd(0x3) is unknown !
<3>[ 8.296864] gc0308 sensor_ioctl cmd(0x3) is unknown !
<4>[ 8.845225] rk fb use 3 buffers
<6>[ 19.304980] DWC_OTG: ********vbus detect*********************************************
<6>[ 19.508432] DWC_OTG: ********soft connect!!!*****************************************
<6>[ 19.514435] DWC_OTG: USB SUSPEND
<6>[ 19.610207] DWC_OTG: USB RESET
<6>[ 19.722420] android_work: sent uevent USB_STATE=CONNECTED
<6>[ 19.725849] DWC_OTG: USB RESET
<6>[ 19.770708] warning: `zygote’ uses 32-bit capabilities (legacy support in use)
<6>[ 19.789466] alarm_set_rtc: no RTC, time will be lost on reboot
<6>[ 19.851344] android_usb gadget: high speed config #1: android
<6>[ 19.851553] android_work: sent uevent USB_STATE=CONFIGURED
<4>[ 20.986377] rk30_adc_battery_poweron_capacity_check……..new_capacity=30,old_capacity=16
<4>[ 20.986404] rk30_adc_battery_poweron_capacity_check…bat ->bat_capacity=16,new_capacity=30,old_capacity=16
<4>[ 33.490421] =======================================================
<4>[ 33.496763] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
<4>[ 33.504244] =======================================================
<6>[ 33.510184] acc_open
<6>[ 33.510208] acc_release
<4>[ 33.510695] Realtek 8188EU USB WiFi driver (Powered by Rockchip,Ver 1.12) init.
<4>[ 33.522799] wifi_usb_init
<4>[ 33.525500] wifi_activate_usb
<6>[ 33.934438] usbcore: registered new interface driver rtl8188eu
<4>[ 34.846224] cfg80211_rtw_change_iface, old_iftype=6, new_iftype=2
<6>[ 34.847300] ADDRCONF(NETDEV_UP): wlan0: link is not ready
<4>[ 36.294939] bssid=ce:06:13:cb:eb:14
<4>[ 36.294959] matched by bssid
<4>[ 36.295436] rtw_cfg80211_set_wpa_version, wpa_version=1
<4>[ 36.295454] got wpa_ie
<6>[ 36.393509] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
<6>[ 40.970833] .409.. MMC0 receive the message sd-Checking from VOLD.[sd_mmc]
<6>[ 40.989720] .409.. MMC0 receive the message sd-Mounted from VOLD.[sd_mmc]
<3>[ 41.028905] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit
<6>[ 44.473253] alarm_set_rtc: no RTC, time will be lost on reboot
<3>[ 73.296942] init: untracked pid 1495 exited
<6>[ 124.382944] Enter::es8323_pcm_startup—-805 es8323->sysclk=11289600
<6>[ 124.383046] Enter::rk29_hw_params—-47
<6>[ 124.383061] es8323_set_dai_fmt—-703, fmt[3000]
<6>[ 124.383071] es8323 in slave mode
<6>[ 124.384192] Enter:rk29_hw_params, 99, rate=44100
<6>[ 124.384211] Enter:rk29_hw_params, 107, LRCK=64
<4>[ 124.410163] fun:es8328_dapm_pre_event, event:1
<6>[ 124.410200] Enter::es8323_set_bias_level—-929 level =2
<4>[ 124.422000] fun:es8328_dapm_pre_event, event:1
<6>[ 124.422023] Enter::es8323_set_bias_level—-929 level =2
<4>[ 124.423929] fun:es8328_dapm_post_event, event:2
<4>[ 124.423946] fun:es8328_dapm_post_event, event:2
<6>[ 124.441070] Enter::es8323_set_bias_level—-929 level =3
<4>[ 124.446543] Enter::es8323_mute—-888–mute=0
<4>[ 128.263811] Enter::es8323_mute—-888–mute=1
<4>[ 133.315434] fun:es8328_dapm_pre_event, event:4
<4>[ 133.315455] fun:es8328_dapm_pre_event, event:4
<4>[ 133.315467] fun:es8328_dapm_post_event, event:8
<6>[ 133.315481] Enter::es8323_set_bias_level—-929 level =1
<4>[ 133.318559] fun:es8328_dapm_post_event, event:8
<6>[ 133.318574] Enter::es8323_set_bias_level—-929 level =1
<3>[ 182.858393] init: untracked pid 1485 exited
<3>[ 187.694941] init: untracked pid 1854 exited
<3>[ 193.742567] init: untracked pid 1427 exited
<6>[ 234.724866] input input0: adkey[vol+]: report ev[115] state[1]
<6>[ 234.814872] input input0: adkey[vol+]: report ev[115] state[0]
rkflashkit log
the RKFlashKit log:
============= 2014-11-09 10:00:14 ============
Loading partition information
MACHINE_MODEL:rk30sdk MACHINE_ID:007 MANUFACTURER:RK30SDK MAGIC: 0x5041524B ATAG: 0x60000800 MACHINE: 3066 CHECK_MASK: 0x80 KERNEL_IMG: 0x60408000 #RECOVER_KEY: 1,1,0,20,0 CMDLINE: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x00800000 mtdparts=rk29xxnand:[email protected](misc),[email protected](kernel),[email protected](boot),[email protected](recovery),[email protected](backup),[email protected](cache),[email protected](userdata),[email protected](kpanic),[email protected](system),[email protected](user)
============= 2014-11-09 10:03:01 ============
Writing file /media/samuel/1A86-DFE7/recovery de test/recovery.img to partition [email protected]
writing flash memory at offset 0x00010000
writing flash memory at offset 0x00011000
writing flash memory at offset 0x00012000
writing flash memory at offset 0x00013000
writing flash memory at offset 0x00014000
Done!
Comparing partition [email protected] with file /media/samuel/1A86-DFE7/recovery de test/recovery.img
reading flash memory at offset 0x00010000
reading flash memory at offset 0x00011000
reading flash memory at offset 0x00012000
reading flash memory at offset 0x00013000
reading flash memory at offset 0x00014000
Done!
************ :
pffffff !!!
don’t work again ;-( pipo smart S1 cwm unpacked and repacked with mkbootimg (my recovery.img-kernel.gz + recovery.img-ramdisk.cpio.gz) ….
realy lost
ok ….
progress ... progress
so my tab is an ” KidsPad 3 “
this cwm work like it is : http://www.filefactory.com/file/605l7c1mh11n/n/Pipo_S1_CWM_by_Danyrolux_rar
but no way to do a nandroid backup “it look like don’t find the good partition”.
if I want to repack it with my original recovery.img, I have to keep the original kernel (from original recovery.img) and the ramdisk from this cwm ..? right ?
the original recovery.img unpack :
[email protected]:/media/samuel/1A86-DFE7/mytools$ sudo perl unpack-bootimg.pl recovery.img
[sudo] password for samuel:
kernel written to recovery.img-kernel.gz
ramdisk written to recovery.img-ramdisk.cpio.gz
cpio: ../init: impossible de créer un lien symbolique vers “sbin/ueventd”: Opération non permise
gzip: ../recovery.img-ramdisk.cpio.gz: decompression OK, trailing garbage ignored
29922 blocs
extracted ramdisk contents to directory recovery.img-ramdisk/
[email protected]:/media/samuel/1A86-DFE7/mytools$
the cwm pipo smart s1 recovery.img unpack :
[email protected]:/media/samuel/1A86-DFE7/mytools# perl unpack-bootimg.pl recovery.img
kernel written to recovery.img-kernel.gz
ramdisk written to recovery.img-ramdisk.cpio.gz
5942 blocs
extracted ramdisk contents to directory recovery.img-ramdisk/
[email protected]:/media/samuel/1A86-DFE7/mytools#
the repack :
[email protected]:~/Bureau/mytools# perl repack-bootimg.pl recovery.img-kernel.gz recovery.img-ramdisk/ reovery.img
5942 blocs
repacked boot image written at recovery.img-ramdisk/-repack.img
[email protected]:~/Bureau/mytools#
*************************
after reboot in recovery mode … the recovery is stil the original recovery ??? I don’t understand.
repacked the original recovery + the cwm ramdisk .
Have you checked with these guys: http://androtab.info/clockworkmod/rockchip/rk3066/
or here: http://forum.xda-developers.com/showthread.php?t=2102679 ?
They work for rokchip cwm too.
helo, thank you for your answer !
yes I read these post and tried the generic CWM (RK3066).
But it don't work with my device.
moreover I don't want pollute there topic with two page of my dmesg :
I would like to build it myself to understand the good way ..
not only ask "can you do it for me ? my device is ...).
Have you any idea about what I doind rong ?
I can provide the boot.img and recovery.img
http://ovh.to/jgiYdg
@+
samco08 said:
helo, thank you for your answer !
yes I read these post and tried the generic CWM (RK3066).
But it don't work with my device.
moreover I don't want pollute there topic with two page of my dmesg :
I would like to build it myself to understand the good way ..
not only ask "can you do it for me ? my device is ...).
Have you any idea about what I doind rong ?
I can provide the boot.img and recovery.img
http://ovh.to/jgiYdg
@+
Click to expand...
Click to collapse
That was the point. I asked you about those guys because they must have a proper device tree to build and you can use that as template to create one for your device. Then you can build any recovery you want. I'm not familiar with rockchip and I can't tell you much, but they probably can... if they want of course.
Besides that I played a little with your files and I repacked that working cwm with your kernel: http://d-h.st/VBK
I don't know if it works, but if it does use it.
Cheers!
carliv said:
That was the point. I asked you about those guys because they must have a proper device tree to build and you can use that as template to create one for your device. Then you can build any recovery you want. I'm not familiar with rockchip and I can't tell you much, but they probably can... if they want of course.
Besides that I played a little with your files and I repacked that working cwm with your kernel: http://d-h.st/VBK
I don't know if it works, but if it does use it.
Cheers!
Click to expand...
Click to collapse
Thank you very much !
but the problem is the same with your recovery
When I reboot, the recovery is the stock recovery ...
I tried with the PIPO Smart S1 cwm (480 x 800) and it work.... but I met an issue with partition ... no way to do a nandroid Backup !
any idea ?
samco08 said:
Thank you very much !
but the problem is the same with your recovery
When I reboot, the recovery is the stock recovery ...
I tried with the PIPO Smart S1 cwm (480 x 800) and it work.... but I met an issue with partition ... no way to do a nandroid Backup !
any idea ?
Click to expand...
Click to collapse
If after flashing recovery it stay unchanged, then the problem is the flashing process. Maybe there is a security or checksum check somewhere and if it doesn't meet requirements it doesn't actually flash the recovery...
I don't know what else to say.
carliv said:
If after flashing recovery it stay unchanged, then the problem is the flashing process. Maybe there is a security or checksum check somewhere and if it doesn't meet requirements it doesn't actually flash the recovery...
I don't know what else to say.
Click to expand...
Click to collapse
yes ...
the PIPO smart S1 CWM flash and start correctly but no way to do a nandroid backup.(partition problem)
Maybe I have to pick up a file in this recovery to repack it in my own recovery.
but witch ?
@+
nobody ?