Hello good day;
I ask you for help to install the Micro-SD card in my computer, it is a Bonroad MTCE_XRC, which apparently did not have an SD card. After requesting the adapter from the brand and refusing to sell it, it occurred to me to disassemble the screen, and there it was... deforming the head of the radio inserted under pressure, after removing it I see that it has 2 cables for the use of the Reset button, I have purchased the connector for it but now I doubt where to connect it, and whether to keep the Reset button with its original wiring, or use it through the new connector.
I attach photos of the motherboard and connectors to see if you can provide me with something where I have to connect it.
I am also going to install a 120mm fan on the top, as well as a heatsink instead of the PX5 module cover, since there comes a time when I have ThermalThrolling, and the browser closes.
Does the fan have to be connected to the red cable that comes from the car's wiring? or is there somewhere to connect it?
Does anyone have the Images of the DSP mod? the post does not have the images for the installation.
My intention with the card is to update Android to its most recent version, and if it convinces me to acquire the Hal9k system
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Related
I was wondering if anyone knows the surface mount part number for the power button on the TF101. My kids not only broke the plastic but also knocked off the surface mount switch.
I've downloaded volume on/off apps but sometimes you need a real power button when flashing and what not.
Any help is greatly appreciated.
Have a look through these parts, you might find it here
http://www.asusparts.eu/en/partfinder/Asus/Pad/Eee pad/TF101
I saw that on another thread but they replace the entire unit i think. I'm sure there has to be a digikey equivalent or something for just the switch right?
I mean I can short the two pins and it powers on/off so i'm sure the the module is fine. I just need the switch.
That site is just a parts site, they just send you out whatever you ask for, I just linked to it because they list the part number on the items
It's just a micro switch really, you could probably find one on ebay, it's only job is to press to connect and release to disconnect, any micro switch that you can find to fit should work
Few here
http://www.ebay.co.uk/sch/i.html?_t...o+switch&_nkw=micro+switch&_sacat=0&_from=R40
EDIT - Something like the smallest here
http://www.ebay.co.uk/itm/09000-Min...mponents_Supplies_ET&var=&hash=item416fe0014d
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Yeah this is more like what I was thinking....Thanks a ton man!
No probs, give us an update if you get it fixed
Hey guys I did a battery swap on my tablet which fixed the reboot issue but I managed to screw up my 4g. Specifically the tablet will not recognize a sim card inside despite rebooting, as well as resetting the card. I did notice upon inspection the black part at the top seems to have fell off. Is this repairable? Or did I brick my tablet
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I'm not really sure what this part is called so I added a picture, it's right above/perpendicular to where the camera would be on the top of the tablet, and its near a microphone
If your SIM card had worked before you did the battery replacement, probably your USB flex or SIM/SD flex is not fully connected. Try to disconnect and reconnect all the flex cables, they are serial connections from Home button, sim/sd, usb port to mainboard. If the SIM slot is defective, you can buy a new one, it costs only $6 to $10, depending where you buy.
http://www.ebay.com/itm/New-Flex-Ca...695527?hash=item35da6abf27:g:0JMAAOSwEK9T3Ial
The small black plastic at the center of LCD frame is IR cover, you can put it back to the frame but the back cover of the tablet has to remove first.
Hello to all,
just want to share a solution for a problem I encountered.
Phone:
Display repaired myself.
Symptoms:
Mobile data and phone reception was unreliable. Seemed to work sometimes, sometimes not usable.
When not usable the network symbol said: No Data SIM/ No SIM, when long pressing on the symbol it said: Invalid network mode (-1)
Cause:
Antenna unplugged, but sometimes it managed to connect due to proximity of the two parts of the plug.
Solution:
Plug the antenna plug back in. (And of course control all the other antenna related contacts.)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
(Picture from ifixit Teardown, step 11. https://de.ifixit.com/Teardown/OnePlus+One+Teardown/26484)
So I seem to have disconnected the antenna cable when disassembling the phone for the display exchange. So glad to have my beloved reliable phone back now!
Hope it helps for some of you!
I first tried all the software stuff, but nothing worked. Heres nice and useful links you could use, if you couldn't resolve your issue via my suggested hardwarefix.
https://forum.xda-developers.com/oneplus-one/general/firmware-modem-oneplus-one-lollipop-t3300907
https://forum.xda-developers.com/oneplus-one/help/fix-brickloop-audio-fx-fc-efs-corrupt-t2879061
https://forum.xda-developers.com/oneplus-one/general/guide-return-opo-to-100-stock-t2826541
Thanks to all of you at xda, who always helped me fix my phones=)
Cheers!
Greetings from Brazil.
I just bought a Galaxy Note 9 and I'm enjoying it so far. I'm very inclined to purchase an used Dex Station for it (the Galaxy s8 used to come with one in Brazil so it's easy to find an "used*" one in good condition (*sometimes they never even used it but they can't sell it as new because they opened and tried it once). Anyways, my note 9 came with a case inside the box. It was alongside the papper instructions and the sim removal tool. My question is: Would I be able to use a Dex Station with this case on the phone? If not, would it fit in the dex pad? Below is a picture of the bottom of the case. I want to use dex daily so to remove and put back the case everytime would be a major headache. I have a usb-c to hdmi cable that worked fine as a dex cable but I want to plug the power cable and an usb keyboard.
Thanks!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
With this case, the phone will fit in Dex
Hi, guys I'm new at this, so bear with me, I got a new android 10 unit from AliExpress, https://a.aliexpress.com/_mLwdGdk, the t7 with 4gb 64gb storage. I got here and checked and it's fine, same specs. My car is a Peugeot 508 2013.
Everything is working according to the specs, but the canbus setting are very different from what I've seen in other units alike this one. The seller has been trying to help me, but is hard due the language barrier and the time difference, 12 hours. I have the code for the factory settings. 3368, dunno if that is helpful.
First I can't seem to find how to put the front camera after reverse with the lines, I tried one option and swaps, but stays on it doesn't automatically turns off. Also there is no option to change the resolution of the camera in the radio.
I saw another video and that unit got messages from the car into the unit.
That's a canbus problem, if it is can I buy another one? Or can it be upgraded without bricking it. Is a launcher issue?, I'm lost.
Also is it safe to install any other launcher via the playstore?
Any tips are really appreciate it.
Thanks
This is the canbus I have installed...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}