It goes like this. I have tried 3 type-c cables and they are all fine when I connect it to my wife's phone to my pc. And when I try these cables, connecting my phone to my pc, the menu or the default usb menu on my phone does not show up. The options where we need to select one, like, the file transfer, usb tethering, transfer photo, midi. It even won't detect any kind of external usb or OTG drive. My usb debugging mode in the developers option is also ON. I am wondering, if my phone needs to replace the charging board or an update or re-firmware can do the fix. Thus, I have done a hard reset and factory reset, but, still nothing happens.
Can anyone know what the issue could be? For the one's who had experienced this? Tia
Look inside here:
How to Turn On/Off USB-OTG - Xiaomi Manual | TechBone
Turn On/Off USB-OTG - Xiaomi:
www.techbone.net
jwoegerbauer said:
Look inside here:
How to Turn On/Off USB-OTG - Xiaomi Manual | TechBone
Turn On/Off USB-OTG - Xiaomi:
www.techbone.net
Click to expand...
Click to collapse
Thanks for the reply. But, sorry my Xiaomi Mi 10T does not have that OTG on & off switch.. It would just automatically connect if a usb is inserted. My usb debugging is also on, but, it cannot detect the inserted usb drive.
Related
Hello Gents,
I purchased a USB OTG for my 7+ last week, all was working. the USB drives works, mouse works.
But this morning, when I tried to use the same mouse/usb drives. The tab does not seem to recognized the USB, I can see the LED on the USB blinks for a few moment and then turn off. Like it's getting power but then stop.
I tried the following.
1. reboot the tab. power on , power off. No go.
2. reboot from factory default ( yes it drives me nuts, but I did it anyway) Power Volume Up. Factory reset, data wipe. No go.
3. tried a new OTG USB cable, still does not work.
I had the Tab root before, but after the system reset, it gone back to stock firmware. The only thing I can think of is I did the latest Samsung Patch after my initial test.
When I look at the "dmesg"
s5p-ehci: detected XactErr len 0/8 retry
tspdrv: ImmVibeSPI_ForceOut_AmpEnable (1)
ImmVibeSPI_ForceOut_AMpDisable...
Does anyone have solution for this problem?
Thank
P.S. these are not the OEM Samsung USB cable. But they were working before.
Also, when I plug in an portable external HDD, it does say, High power device not supported.
hi,,,
try to connect all tools to usb otg hub first before you conect it to GTab. i mean if you want to connect a flash disk or a mouse, connect them to the usb otg hub first before connect it to GTab.
for hdd, you have to connect a power supply to usb otg to make it readable on GTab. i use my old nokia charger to power the usb otg hub device.
hope it help and sorry for my bad english.
dan
edit : i use this device as usb otg hub
http://db.tt/fmw1MhTY
I have the same error.
I have the same error but when I reboot my Tab, it's ok, before reboot I do not disconnect USB from my tab!You can try!
So on my Galaxy A8 I have developer options unlocked with USB debugging on and when I plug in USB to my computer it asks me if i want to allow access to phone data. Deny obviously makes it so its only charging but accept and I can access files (all well and good so far). However when I go to Tap for other USB options it has options for Use USB for: Transferring files, USB tethering, MIDI, Transferring images, and charging phone only... however I can't actually change any of these options.... So why can't I change the options, and is Transferring images ptp?
Hi I just did tried it in USB Default Settings and it works for me
I am able to chnage any kind of USB mode
try it with the phone unpluged from the computer maybe !
Pro Cal said:
Hi I just did tried it in USB Default Settings and it works for me
I am able to chnage any kind of USB mode
try it with the phone unpluged from the computer maybe !
Click to expand...
Click to collapse
Yeah I'm in usb settings but the actual settings are locked out from changing... does anyone know why this is?
A8 USB
I have this problem too. I can 't choose for other usb options. I haven't enable USB debugging.
Hi, if you enable developer options then you can choose under developer options - default USB configuration - which option you want.
Phil
i tried all of those options and none of them work, is there any other ideas?
Hello All,
I stumbled upon a problem with my Mate 30 pro. When using a USB stick and or USB card reader I can only select "use USB to reverse charge". When selecting the other options like transfer photos or transfer files the selection jumps after 2 sec back to reverse charge.
I use File manager to transfer pictures from my phone to my computer via a stick and due to this it fails to do this, well it fails to transfer pictures from my phone to my USB stick, from the stick to the phone works...
Using the internal file manager then it works...uninstalled file manager rebooted the phone and reinstalled did not solved my problem. I prefer to work with the file manager from play store and not the internal one...
Google play store is on the latest version, well the same version like on my mate 20 pro.
Just realized that my mate 20 pro is doing exact the same, but there transfer files/pictures from phone to USB stick works.
Have u tried developer options - USB debugging?
viruz1225 said:
Have u tried developer options - USB debugging?
Click to expand...
Click to collapse
Yes I did, also tried to change the same setting - USB config - in the developer options but there it also reverts back to charge only.
I see the exact same automatic return to "Reverse charge" after 2 seconds using OTG, but I can use the internal file manager, so I am not
bothered so much by that. What bothers me is that I want to charge normally (opposite of "Reverse Charge") using OTG since I am using
"Accessory Charging Adaptors" (i.e., I am using an OTG USB Hubs with a power supply included). After many experiments, I see no way to
simultaneously charge my Mate 30 Pro and use an OTG device - Has anyone found a way to do this?
If ACA doesn't work, then chances are that your USB controller driver doesn't have it implemented
[KERNEL] (Patch) USB OTG (host mode) + simultaneous charging!
(I really struggled with where to post this. Although much work and effort went into debugging unique Z5-specific issues, this is based on prior work so I put it here instead of in "original"; also, I would be very surprised if this didn't apply...
forum.xda-developers.com
Phone is rooted and on android 10 and xxxnolimits installed
I connected phone to pc and only charging. Tried 3 different cables, including official one and 3 different USB ports and not showing on pc. I can hear noise it's connected to pc but then another noise to disconnect
Usb debugging is enabled and default usb configuration I can change to file transfer, usb tethering , midi, ptp & no data transfer. I changed it to each of them still not showing
There is no option to choose mtb from drop down notification no notification is there
I rebooted phone and pc and cleared cache. Also i app settings allowed notifications.
I'm at the end of my tether trying to figure out what issue is as was working previously.
Now all its doing is charging
Any suggestions
funkyirishman said:
Phone is rooted and on android 10 and xxxnolimits installed
I connected phone to pc and only charging. Tried 3 different cables, including official one and 3 different USB ports and not showing on pc. I can hear noise it's connected to pc but then another noise to disconnect
Usb debugging is enabled and default usb configuration I can change to file transfer, usb tethering , midi, ptp & no data transfer. I changed it to each of them still not showing
There is no option to choose mtb from drop down notification no notification is there
I rebooted phone and pc and cleared cache. Also i app settings allowed notifications.
I'm at the end of my tether trying to figure out what issue is as was working previously.
Now all its doing is charging
Any suggestions
Click to expand...
Click to collapse
Do you have the latest fastboot-adb platform tools installed? Just a thought.
Will check
However usb notification drop down not coming up on phone to change settings when I plug phone into port.
Also plugged phone into USB port of car for android auto and not picking it up
If I restore a backup would that be worth trying or does issue seems to be with usb port on phone?
funkyirishman said:
If I restore a backup would that be worth trying or does issue seems to be with usb port on phone?
Click to expand...
Click to collapse
Try uninstalling and reinstalling usb google drivers on your pc ( or your appropriate driver's for your phone).
Install OEM USB drivers | Android Studio | Android Developers
Discover links to the web sites for several original equipment manufacturers (OEMs), where you can download the appropriate USB driver for your device.
developer.android.com
Are you talking about usb drivers?
I installed this one
OnePlus USB Drivers | Official
Download the latest version of OnePlus USB Driver for your OnePlus smartphone. OnePlus USB Drivers helps your OnePlus smartphone to communicate properly with your computer.
oneplususbdrivers.com
Still not working
Phone not showing up in device manager
Also tried the below and phone just keeps on rebooting
in Developer option > USB debugging ON
turn off phone
connect cable
turn ON phone
Still looking for a solution
Tried cable on old one plus 5 and it's working fine on pc
So must be phone
Any suggestions on what to try
Hello,
My device is Oppo F5 Youth (CPH1725),
The screen is broken and it's dead black but the phone is working.
I need to extract my data from it and can't connect it to USB because when I do it usually pops up the USB mode selection screen which is by default on charging mode and I don't have USB debugging active.
Any ideas about extracting the data?
You should make sure that your Android phone is equipped with OTG feature. Then you can utilize an OTG USB cable and a mouse to extract files from your device wirelessly.
RamiAbbas said:
Hello,
My device is Oppo F5 Youth (CPH1725),
The screen is broken and it's dead black but the phone is working.
I need to extract my data from it and can't connect it to USB because when I do it usually pops up the USB mode selection screen which is by default on charging mode and I don't have USB debugging active.
Any ideas about extracting the data?
Click to expand...
Click to collapse
If you haven't enabled OTG support in phone's Android Settings -> Advanced you have no chance to extract data of interest, IMO.
bobii said:
You should make sure that your Android phone is equipped with OTG feature. Then you can utilize an OTG USB cable and a mouse to extract files from your device wirelessly.
Click to expand...
Click to collapse
It have OTG but how connecting mouse would help? I can see anything from the screen!?