Model:Huawei p40 lite
Hello, recently I flashed most propably bad firmware version and now the device seems to be soft bricked.
Black screen, no vibration while pressing power button, nothing.
However when I connect phone to PC, it does detect a device, I download HiSuite and device gets detected as Sooner ADB interface, but via HiSuite shows that recovery is not supported within the model.
ADB is also installed but devices show no devices at all.
When I press power button and volume down it seems to enter another state but device name/driver is the same. No fastboot.
It seems like it is not dead at all but I would have to use somekind of flash tool.
Any ideas would be appreciated
Thanks
Hi, is there a solution?
I need a solution to. Someone?
I am in the same situation. Is there someone to help?
Related
Hello to everybody.
I have a problem with my mate8.
After flash rom on TWRP phone will not boot. Only a black screen (phone off), no logo, no bootloop. Twrp recovery does not run, eRecovery not run.
Phone does not react to any combination of volume + - and power. After connecting to the PC is still in fastboot mode. Even with the battery disconnected.
Rayglobe knife or SRKtool performs unbrick but the phone will not boot, it is still only in fastboot. TWRP or eRecovery installs, but will not boot.
Fastboot commands some works, adb commands says "device not found " , "waiting for device" or remote: command not allowed.
It is possible to install UPDATE.APP via fastboot?
Bootloader is unlocked and FRP locked. I can not turn on USB debugging.
Is there any way to recover your phone, or is totally dead?
Helps DC Phoenix?
Thanks for any ideas.
EDIT: Solved. Using DC Phoenix, unbrick and phone works again.
How??? My phone is dead also l29 c158
I CAN GET TO FAST BOOT.....FLASHED ALLTHAT T I CAN BUT NO RESULT....I PURCHASED CREDITS ON DC PHOENIX BUT TILL NOW NO RESULT AS IT CANT RECOGNIZE MY PHONE...
My phone was still in fastboot mode, so it was easier.
I followed instructions (Huawei Mate S flashing in fastboot by DC Phoenix on YouTube) .
My version is NXT-L29 C432.
I downloaded the official firmware C432 B320 and DC Phoenix performed a flash.
It was then a little problem with the battery, but unplugging, turning on the phone without the battery and then reconnect the battery managed to turn the phone on. Then I flash the firmware update.app in stock recovery and the phone is alive.
Spent 15 euros, but better than brick.
I would try to support dc phoenix. It might help.
Thank you...After trying to flash new firmware by DC phoenix.....My phone is completely dead.....NO power working....I think I must search for a new phone....anyway .......just I advise everyone to be careful when rooting Nougat.....
When connecting a charger flashes red, or does not respond at all?
premda said:
When connecting a charger flashes red, or does not respond at all?
Click to expand...
Click to collapse
NO response at all....no repose to charging or PC at all...
basimzanaty said:
NO response at all....no repose to charging or PC at all...
Click to expand...
Click to collapse
Windows Device Manager does not detect the attached device?
He is probably dead :crying:
My mate 8 NXT -L29 is completely dead.I updated to noughat B563 and i found out my Bluetooth was not working completely,then i tried to downgrade it to B500 ,the update got 99% and then phone got switched off.No waking up no matter what.I tried the hard reset too with all combinations of voume and power button but no response.BUt when i connect my phone to PC Huawei suite opens up but cannot access. I removed the battery and then inserted it , still no life.Please give me a solution.
Hi...
I have problem with these tablet. I suddenly wrong installing blob from TWRP devices last night. After i twrp reboot, BOOM.. My tablet bricked, i pressing VOL- and power button to get into fastboot, but my tablet not responding. I browse on net, my tablet has not have fastboot, and bootloader anymore. I try pressing VOL+ power button, APX driver install automatically after i connected to pc. I search many webs include xda, some users had that problem. So, i can't found the best tutorial to fix.
I use windows 7 for my pc. Is there any tools or tutorial to solve my problem. Cause, many data's in my tablet that im not backup yet..
Thank you..
help
help
hmm.. no one can't help me to solve this...
Hello roomraditz, right now this issue doesn't have any easy solution if you are entering on the APX mode means that the firmware has been corrupted anyhow and in order to install anything in this mode you would need to recover some keys that are not available at this moment.
I have been working on find these keys but I didn't have any result yet.
https://forum.xda-developers.com/sh...porting-tegra-x1-exploit-to-tegra-k1-t3960111
Hello, I recently received Huawei SCL-L21, but after trying to turn on the phone there is an issue. Everytime black screen pops up saying "Failed to verify boot image" this screen is displayed for like 1 second and then the phone switches to "Fastboot&Rescue mode" and says I should connect to HiSuite and below there's green text "Phone Locked FRP Lock".
So I tried to upload new firmware via the Dload method using SD Card, but the phone doesn't do anything
Here's what I did
1) Create folder called "dload" on your sd card
2) Put the UPDATE.app there
3) Press volume up + volume down, then press Power button ALSO TRIED Press volume up + volume down + power button and release power button when Huawei logo appears.
I also tried to flash via PC watching youtube tutorial, but whenever I plug the device it's not detected as a COM port even through I have installed official Qualcomn USB drivers.
Can anyone please tell me where's the problem? Is it related to the " "Phone Locked FRP Lock" message or is it something else?
Thanks in advance.
Use official "Huawei USB Driver" suitable to your phone instead of Qualcom USB Driver
jwoegerbauer said:
Use official "Huawei USB Driver" suitable to your phone instead of Qualcom USB Driver
Click to expand...
Click to collapse
What program should I use to flash via Huawei USB driver?
bump
The Huawei "Android USB Driver" for your Huawei Y6 SCL-L21 has to get installed on computer.
That's the driver I am asking what program do I use to flash via the Huawei driver? Since QFIL seems to only work with Qualcomn driver or am I wrong
That's my understanding:
QFIL is a flash tool, Qualcomm is a SoC, Huawei's Android USB Driver is needed to manage the phone's bootloader via computer.
What I know is:
Huawei offers Hisuite what typically is used to fix problems and also to re-flash a Stock ROM.
BTW: Wondering why you have 2 identical threads started here: it's against the forum rules, AFAIK.
I already got Huawei USB driver installed, but the phone is not detected in HiSuite, so I can't do anything right now via HiSuite
My wife's Huawei Y7 2019 gets detected by both HDB and ADB/Fastboot, but must say the phone didn't get tampered in any way.
MatejKalik said:
Hello, I recently received Huawei SCL-L21, but after trying to turn on the phone there is an issue. Everytime black screen pops up saying "Failed to verify boot image" this screen is displayed for like 1 second and then the phone switches to "Fastboot&Rescue mode" and says I should connect to HiSuite and below there's green text "Phone Locked FRP Lock".
So I tried to upload new firmware via the Dload method using SD Card, but the phone doesn't do anything
Here's what I did
1) Create folder called "dload" on your sd card
2) Put the UPDATE.app there
3) Press volume up + volume down, then press Power button ALSO TRIED Press volume up + volume down + power button and release power button when Huawei logo appears.
I also tried to flash via PC watching youtube tutorial, but whenever I plug the device it's not detected as a COM port even through I have installed official Qualcomn USB drivers.
Can anyone please tell me where's the problem? Is it related to the " "Phone Locked FRP Lock" message or is it something else?
Thanks in advance.
Click to expand...
Click to collapse
I have the same problem, where have you found the firmware update.app?
Hi, I accidentally bricked my phone flashing the wrong image.
Now i can't turn off the phone, cant access to recovery or fastboot. (device doesn't respond when i click any button).
'Poco' logo is in loop. Anyone knows a way to install a ROM? Any way to access fastboot in this situation?
Try pressing the buttons for a long time. It resulted for me to get to recovery mode, but no to download mode. Sometimes it works.
I bought a poco x4 gt like that too, hoping to get it fixed, I believe the way to get it is via EDL mode and miFlas, but for now miflash still doesn't recognize the image of the poco x4 gt. I hope that in some future update I will recognize it.
i have same problem
Same problem here
did anyone was able to find a fix? or at least locate the test points for EDL?
mtk devices use a different way to access edl mode. in my case I access the edl mode, the computer recognizes it, the software recognizes it, but when running it says that SPflash still does not work with the scartter version of the rom that I downloaded
how did you manage to boot into edl mode? i tried several hw key combinations but it gives me "preloader handshake failed" or several BROM error.
i think my scatterfile seems ok. its just the brom/edl connection.
when you turn it on with the volume button less pressed and it connects quickly to the pc install the MTK driver and then run the python where it will read the brom
Mine already fixed
butaw1 said:
Mine already fixed
Click to expand...
Click to collapse
what did you do?
if any one want to fix his poco x4 gt bootloop only. can't reach fastboot or recovery. at first you need auth to bypass dim 8100 security. i found a person on github name Rafon he fixed my phone and it's working perfectly right now. his username on telegram is @Rafon24
same issue
the only way of fixing is through an authorized xiaomi account sadly
i however found a way to turn it off when nothing works:
press all 3 buttons (volume up, down and power for like 20 seconds)
and then it will turn off
hello everyone
i think i bricked my xiaoxin pad p11 pro 2021 trying to root it
i was able to install TWRP and while i was browsing inside it, i pressed partition B and the tablet went to black
and is completely unresponsive now.
is not turning on, or charging or vibrating or flashing or anything.
i conected it to the pc to see if fastboot was there but it doesnt find the device no matter in what way i try to reboot it
but the usb port still is recognizing a devices plugged in, so i used QFIL and discover than the tablet is in "Download Mode"? i dont really know was that means.
so i tried to flash the stock rom into the tablet in download mode, aparently if i press vol down and power for 20 seconds or so the tablet reboot without giving any signal except for the conexion to the pc, but the flash doesnt work.
i tried QFIL with the proper qualcom drivers, also lenovo download tool and even in the rescue and smart assistant, but like it doesnt include support for this tablet, i tried with similar models and roms but it also fail.
i dont know if it is because is in the wrong partition or why there was a second one but fails every time, even tried with different roms from different links but nothing.
is there a way to flash the tablet or recover the fastboot or anything that stop me from declare it lost forever?
i'll attach the error log from the QFIL if that can help.
thank you for your help and your time.