п Without reading the instructions, I put 12 android and the recovery died, I put another recovery through Bugjaeger - did not help, the debt was loaded on the splash screen and then rebooted into the system. what to do? without pc
Related
I bricked my phone while downgrading from the Brazilian lollipop to Asian Kit Kat, I did it directly which I think was my mistake. My phone won't boot up android or even the recovery (twrp). When I do a fastboot and choose recovery it will reboot into the recovery and show the flickering screen (different from the one you get after downgrading) and shows the android symbol with a warning sign. I tried to flash a new cm12 while the recovery was working and it said it was successful, which caused the damage to the recovery. At that point my phone could no longer be detected by my windows PC (tried on a different PC with ubuntu). I took my phone to some stores thinking it can be repaired but they failed, they only managed to get the recovery to work again (cwm). I tried installing a cm12 again using otg, it seemed as if it was successful but when I restarted my phone it failed and broke the recovery again. I just left the phone till it ran out of battery since it won't turn off. I'm hoping someone out there might have a solution, I tried most of what I could find on the net but alas.
Is there no one with a solution :crying:
Help....
I have been loading custom Roms on this device, but when I tried to install a new Rom, I didn't have the unit fully charged and it went dead. When I grabbed the cable to turn it back on, its booting to the TWRP Boot Screen and wont let me boot into custom recovery or anything else. Just keep rebooting over and over... Any help, please...
Let TWRP boot to the curtain, run adb pull /tmp/recovery.log - and post the file somewhere.
I'm not sure what i did but i decided to install android 9 on my Samsung galaxy s7 (SM-G930F)
I installed android 9 on my phone and did not like it, so i went to reset it to stock 8.0 oreo firmware.
My phone was not rooted properly at this time* (not sure if that may have something to do with it.)
I went to reset it back to oreo and i factory reset my phone from TWRP, i wiped it and then it was stuck on wiping for a hour or so, So i held all 4 buttons to get to download mode to install 8.0.
It wouldn't allow me to install 8.0. it would just Fail every time. I tried turning my phone on, it would kick me to TWRP Recovery and it would NOT load. It is just stuck with the usual loading of TWRP With the logo, Teamwin and recovery project 3.1.3.0
I was able to put on TWRP 3.2.3.0 But it didn't help. it is just stuck on the loading part of TWRP before you get any of the options so i can't do ANYTHING on my phone.
I can NOT Get into the TWRP
I can NOT Flash on android oreo 8.0 using Odin
I can NOT Boot up my phone normally
my phone is either in the TWRP Loading screen or in download mode all the time. Unless my phone dies then its off,
If anyone has had this issue or can help please do, It would be greatly appreciated
Hello people!
I have a J400F phone model, I was working with android 9 rooted & working well, I updated to android 10 with a fresh install, the phone works well, and I wanted to use a custom recovery TWRP and root the phone, it stuck in boot loop, this is how I flashed:
- Used Odin with the latest stock firmware "J400FXXU6CTGO".
- restart the phone, and the bootloader is already unlocked "OEM Unlocked".
- Downloaded TWRP for J400F from halabtech, flashed it, then rebooted to recovery.
- In home screen, Wipe --> Format.
- With TWRP I flashed RMM_Bypass_v3_corsicanu.zip then no-verity-opt-encrypt-6.1.zip
After this I tried booting to system but then It kept rebooting after reaching the samsung logo.
Any help is appreciated guys.
I managed to access the download mode by taking out the battery, put it back in the phone, connect it to USB in the computer, press vol down and home button and you should be able to enter the download mode to flash the stock ROM (still reading on the second part).
Help.
I was on Android 10 and I just flashed latest 2021 MARCH full firmware.
following this: https://forum.xda-developers.com/goto/post?id=84193795
Update was fine and phone rebooted successfully.
Magisk was fine too.
I flashed Magisk afterwards (flash to inactive slot after OTA)
Then, I found out that I did not have TWRP anymore,
so I went into Bootloader mode, and via ADB, booted up TWRP 3.4.0.0
then, I flashed TWRP [twrp-3.4.0-0-I0W1D-Q-mauronofrio]
and rebooted to recovery, to see if TWRP was there...
...and now my Zenfone 6 cannot boot up anymore.
I think I flashed TWRP 3.4 and not 3.5
I really, really don't know what to do now,
ie. phone screen is black but I can briefly see the TWRP logo,
before phone goes black again.
I cannot go into Bootloader mode nor does pressing down on the power button down for 10-seconds do anything.
EDIT:
it's the same situation as this
-- https://forum.xda-developers.com/t/...enfone-6-stable.3937844/page-12#post-84205699
It seems official android 11 support is broken. Twrp logo flashes for a sec and then bootloops. Any chance for quick update?
I managed to boot into the phone (by pressing VOL down + POWER).
Basically, my TWRP is corrupt or incompatible with Android 11.
So, I got to figure out how to remove TWRP completely (because I have lost root too)
MODS,
please delete this thread because i am certain now that
the cause of my bootloops, etc... were due to TWRP
not being compatible with Android 11