Related
Team Win Recovery Project 3.0.2-0
This is for the Exynos SM-T377T and SM-T377W models only! Do not flash on Qualcomm models!
They have only been tested on the LTE models.
WARNING: Flashing a custom recovery to your device will trip the Knox warranty bit on your phone. Check with your mobile provider to see if they will still cover warranty on Knox bit triggered devices. If you understand this risk, continue on.
WHAT IS TWRP?
Oh come on, you know what it is - don't try to fool me!
In case you're serious, though...
Team Win Recovery Project is a custom recovery for Android devices.
It allows you to back up and restore your data, flash custom ROMs to your device, repair broken file systems, and root your device.
DOWNLOAD
You can find the device page here:
http://teamw.in/devices/samsunggalaxytabe80exynos.html
There is a download link there, as well as instructions on how to flash it.
I highly recommend using Odin to flash when possible.
You can find a zip containing Odin as well as a link to Samsung's Mobile drivers page here:
https://idlekernel.com/flash-tools/
FULL STEPS FOR OBTAINING ROOT
Extract Odin_3.10.7.zip to your computer.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Install Samsung Mobile Phone Drivers for Odin to find your device.
Download a .tar image of TWRP for gteslte.
Reboot your device into Download mode. To do this, select reboot from the power menu and hold the [Volume Down] + [Home] buttons while your device reboots.
Once you reach the Download mode warning screen, press [Volume Up] to continue.
Open Odin and place that TWRP tar file in the [AP] slot without touching any other options, then press [Start].
Hold [Volume Up] + [Home] buttons near the end of the flash, and keep holding them until you are in recovery.
At this point, you will reach the screen asking you if you want to allow system modifications.
You will want to swipe to allow, otherwise the OS will replace TWRP once you boot!
If you want to be rooted with SuperSU:
Download the latest SuperSU by Chainfire.
Without exiting TWRP, transfer the SuperSU zip to your device over MTP* and flash it using [Install] in TWRP.
Go to [Reboot] -> [System].
* MTP, known as Media Transfer Protocol, is the same way you transfer files from your PC to your device when booted into system.
CHANGES
v3.0.2-0 - Initial build on twrp.me
FEATURES
MTP support
USB Mass Storage support
Micro SDcard and USB OTG storage support
f2fs file system support (read, write, format, backup & restore)
exFAT file system support (read, write, format, backup & restore)
NTFS file system support (read, write, format)
ADB root
Full SELinux support
Built in android 6.0 tree
KNOWN ISSUES
Samsung encryption is not supported yet in TWRP 3 (see: https://gerrit.omnirom.org/#/c/17308/)
CONTACT & SUPPORT
You can find us on IRC at #twrp on chat.freenode.net.
You can also post in this thread and I will attempt to answer any questions you may have.
SOURCE CODE
TWRP: https://github.com/omnirom/android_bootable_recovery (android-6.0)
Device tree: https://github.com/TeamWin/android_device_samsung_gteslte (android-6.0)
Kernel: https://github.com/jcadduono/android_kernel_samsung_gteslte (twrp-6.0)
CONTRIBUTIONS
Gerrit for TWRP: http://gerrit.omnirom.org/
Gerrit for officially supported devices: http://gerrit.twrp.me/
XDA:DevDB Information
Team Win Recovery Project - Samsung Galaxy Tab E 8.0, Tool/Utility for the Android General
Contributors
jcadduono, Team Win & friends
Source Code: https://github.com/jcadduono/android_device_samsung_gteslte
Version Information
Status: Stable
Current Stable Version: 3.0.2-0
Stable Release Date: 2016-07-15
Created 2016-07-16
Last Updated 2016-07-15
Qualcomm modem LTE
jcadduono said:
This is for the Exynos SM-T377T and SM-T377W models only! Do not flash on Qualcomm models!
They have only been tested on the LTE models.
Click to expand...
Click to collapse
Hi, I am very new. My device is a T377W LTE edition... I believe it's a qualcomm snap dragon 410. Looks like this build does not work on mine.. Is there any plan to support Qualcomm tab E please?
Thanks in advanced.
kc2 said:
Hi, I am very new. My device is a T377W LTE edition... I believe it's a qualcomm snap dragon 410. Looks like this build does not work on mine.. Is there any plan to support Qualcomm tab E please?
Thanks in advanced.
Click to expand...
Click to collapse
http://forum.xda-developers.com/android/development/recovery-samsung-tab-e-sm-sm-smnu-smp-t3302935
you don't have a T377W you have a T377P / T377R4 if it is snapdragon
Hi, my device is T3777, and it also works fine after installing the twrp and rooting.
Thanks for your valued experience and it really helps me a lot.
There is no .tar
Tacodelish said:
There is no .tar
Click to expand...
Click to collapse
https://www.androidfilehost.com/?fid=24665509702140789
I ended u making a tar...thx though.
Does anyone know of any non-stock ROM's for our T377W?
i tried it, got TWRP on there, but when I run root checker, still says that I don't have root. I have the tmobile T377T version. Tried Flashing the super su beta as well, still doesn't say I have root, but the su icon is on the device now. What did I do wrong?
---------- Post added at 09:43 PM ---------- Previous post was at 09:24 PM ----------
Never mind, got it rooted, i was using the wrong chainfire file. Good to go, Thanks for everything!!!!!!
Drunken1 said:
i tried it, got TWRP on there, but when I run root checker, still says that I don't have root. I have the tmobile T377T version. Tried Flashing the super su beta as well, still doesn't say I have root, but the su icon is on the device now. What did I do wrong?
---------- Post added at 09:43 PM ---------- Previous post was at 09:24 PM ----------
Never mind, got it rooted, i was using the wrong chainfire file. Good to go, Thanks for everything!!!!!!
Click to expand...
Click to collapse
Here is what I ended doing when I had this problem ...
Download the latest STOCK FIRMWARE at this website or use SamFirm
Completely WIPE your device with TWRP (Format everything!)
Use ODIN 3.12.4 to install the STOCK FIRMWARE you downloaded above
Re-Install TWRP
Re-Do SuperSU SR4
That process fixed my same issue with root not sticking. Hope it works for you. Please make sure you have a good download of the STOCK FIRMWARE. If you don't, you have nothing to install after the wipe, there will be no nandroid backup, etc. You need ODIN and STOCK FIRMWARE to have this work!
Everything worked fine but when uninstalling bloatware i uninstalled something (can't remember the name) which i shouldn't have and now i get the error that there is no OS installed. Is there a way to fix this for the t377W?
Does anyone have stock ROM for T377T? I can't find it anywhere.
jcadduono said:
Team Win Recovery Project 3.0.2-0
This is for the Exynos SM-T377T and SM-T377W models only! Do not flash on Qualcomm models!
They have only been tested on the LTE models.
WARNING: Flashing a custom recovery to your device will trip the Knox warranty bit on your phone. Check with your mobile provider to see if they will still cover warranty on Knox bit triggered devices. If you understand this risk, continue on.
WHAT IS TWRP?
Oh come on, you know what it is - don't try to fool me!
In case you're serious, though...
Team Win Recovery Project is a custom recovery for Android devices.
It allows you to back up and restore your data, flash custom ROMs to your device, repair broken file systems, and root your device.
DOWNLOAD
You can find the device page here:
http://teamw.in/devices/samsunggalaxytabe80exynos.html
There is a download link there, as well as instructions on how to flash it.
I highly recommend using Odin to flash when possible.
You can find a zip containing Odin as well as a link to Samsung's Mobile drivers page here:
https://idlekernel.com/flash-tools/
FULL STEPS FOR OBTAINING ROOT
Extract Odin_3.10.7.zip to your computer.
Install Samsung Mobile Phone Drivers for Odin to find your device.
Download a .tar image of TWRP for gteslte.
Reboot your device into Download mode. To do this, select reboot from the power menu and hold the [Volume Down] + [Home] buttons while your device reboots.
Once you reach the Download mode warning screen, press [Volume Up] to continue.
Open Odin and place that TWRP tar file in the [AP] slot without touching any other options, then press [Start].
Hold [Volume Up] + [Home] buttons near the end of the flash, and keep holding them until you are in recovery.
At this point, you will reach the screen asking you if you want to allow system modifications.
You will want to swipe to allow, otherwise the OS will replace TWRP once you boot!
If you want to be rooted with SuperSU:
Download the latest SuperSU by Chainfire.
Without exiting TWRP, transfer the SuperSU zip to your device over MTP* and flash it using [Install] in TWRP.
Go to [Reboot] -> [System].
* MTP, known as Media Transfer Protocol, is the same way you transfer files from your PC to your device when booted into system.
CHANGES
v3.0.2-0 - Initial build on twrp.me
FEATURES
MTP support
USB Mass Storage support
Micro SDcard and USB OTG storage support
f2fs file system support (read, write, format, backup & restore)
exFAT file system support (read, write, format, backup & restore)
NTFS file system support (read, write, format)
ADB root
Full SELinux support
Built in android 6.0 tree
KNOWN ISSUES
Samsung encryption is not supported yet in TWRP 3 (see: https://gerrit.omnirom.org/#/c/17308/)
CONTACT & SUPPORT
You can find us on IRC at #twrp on chat.freenode.net.
You can also post in this thread and I will attempt to answer any questions you may have.
SOURCE CODE
TWRP: https://github.com/omnirom/android_bootable_recovery (android-6.0)
Device tree: https://github.com/TeamWin/android_device_samsung_gteslte (android-6.0)
Kernel: https://github.com/jcadduono/android_kernel_samsung_gteslte (twrp-6.0)
CONTRIBUTIONS
Gerrit for TWRP: http://gerrit.omnirom.org/
Gerrit for officially supported devices: http://gerrit.twrp.me/
XDA:DevDB Information
Team Win Recovery Project - Samsung Galaxy Tab E 8.0, Tool/Utility for the Android General
Contributors
jcadduono, Team Win & friends
Source Code: https://github.com/jcadduono/android_device_samsung_gteslte
Version Information
Status: Stable
Current Stable Version: 3.0.2-0
Stable Release Date: 2016-07-15
Created 2016-07-16
Last Updated 2016-07-15
Click to expand...
Click to collapse
I got the dreaded custom binary blocked by FRP lock. I did something stupid. Turned bootloader lock on again as i didn't realize that it would block TWRP and the booting of the device. The root process and installation of TWRP went great. Thank you....
I rooted mine to play with xmodgames, but I can't get it to work unless I get a custom rom or kernel. That is where I can't find a rom or kernel for small t377t 6.0.1 as of right now
I tried flashing the tar file for TWRP and it fails in Odin. I have the Tab E T377T and it's currently soft bricked. Is there an Odin flashable recover file that will work. I can only find IMG file on TWRP webpage.
Solved. Created my own tar file and flashed with Odin. Rooted and working great!
All rooted, working good. Are there any roms out there yet?
Sent from my SM-T377T using XDA-Developers mobile app
s_uperd_ave said:
All rooted, working good. Are there any roms out there yet?
Click to expand...
Click to collapse
I have the same question!
I have the SM-T377T, cpuz says I have ARM cortex-a7. So I assume this is Exynos as my s7 edge has exynos and comes up as cortex as well. Just want to confirm before flashing the incorrect img and soft bricking. Thanks in advance!
sparkx86 said:
I have the SM-T377T, cpuz says I have ARM cortex-a7. So I assume this is Exynos as my s7 edge has exynos and comes up as cortex as well. Just want to confirm before flashing the incorrect img and soft bricking. Thanks in advance!
Click to expand...
Click to collapse
Should work fine. I have the T377T and flashed successfully with Odin.
jdon723 said:
Should work fine. I have the T377T and flashed successfully with Odin.
Click to expand...
Click to collapse
Thanks! I'll give it a shot!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This is a Official Build of madOS ( based on AOSP 8.1.0 ) for Vernee Apollo Lite & X with MTK 6797 SoC
madOS is based on pure A.O.S.P. with many additional customizations and MediaTek support.
Code:
#include
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
Installation Instructions:
The latest 7.1.2 build must be flashed in SPFT with firmware upgrade mode before this ROM can be flashed (Downloads: VAL, VAX)
Download ROM from M.A.D. Facebook
OR from xda DevDB
Download 8.1 GApps from xda devdb (Mirror)
Backup
Flash new mandatory new Oreo TWRP (available on downloads)
Boot to the new TWRP recovery
full Wipes (dont come crying if you didn't .. ;p )
Install rom (optionally following by GAPPS if you use them)
Optional: go to: wipe --> Advanced Wipe, tick 'cache' and klick 'repair or change File System' --> change File System --> F2FS --> swipe to the right (hit back several times, and proceed the same way with 'data').
Reboot System
Working:
RIL (Calls /SMS, Data connection, etc)
Wifi
Bluetooth
FM Radio
All Sensors
Fingerprint
Lights
Both storages & MTP
HW de/encoding
Camera (photos and video)
GPS & aGPS
Audio
madOS Extras (the features ya'all used too), plus, some new features we added on Oreo)
Bugs:
-
XDA:DevDB Information
madOS_O_VAL_VAX, ROM for all devices (see above for details)
Contributors
fire855, DerTeufel1980, superdragonpt
Source Code: https://github.com/MediatekAndroidDevelopers
ROM OS Version: 8.x Oreo
ROM Kernel: Linux 3.x
ROM Firmware Required: TWRP
Based On: AOSP
Version Information
Status: Stable
Stable Release Date: 2017-12-25
Created 2017-12-25
Last Updated 2018-01-13
General F.A.Q.
Q: What the hell is madOS ?
A: madOS, (M.A.D. Team OS), is a ROM based on pure A.O.S.P. with extended capabilities and customizations made by or merge/adapted by M.A.D. Team.
Q: Which recovery should I use for this ROM?
A: Latest M.A.D. TWRP 3.2.1-0 recovery
--> Check xda Download Section
Q: How do i flash new recovery ?
A:
1: You can flash it with a scatter file (LP rom layout)
2: You can simply flash it from the existing twrp recovery: Install> Install image> Select Oreo TWRP> Select "Recovery" as partition to flash.
Reboot to recovery to use new one
Q: Do i need to make full wipes?
A: YES, dont come crying at me, if you didn't .... ;p
Q: What is "full wipes" ?
A: To Wipe : Cache; System; DATA ...
Q: What should i use f2fs or ext4?
A: Both are supported, choose the one you desire
Q: is the Data connection issue of going to / from 4G still present?
A: nope data switchs pretty fast on our new RIL
2G>3G>4G | 4G>3G>2G pretty fast
Q: Does this rom have any Theme support
A: Yup, We have working Theme Engine (madOS extras)
Q: Some translations are missing for my language, can I help?
A: Sure you can, please check our translations repo available here , you can either do a pull request, or if you don't know how to work with git, sent us the XML. Strings for your language ( Check Readme on repo).
Q: I want to report a bug(s) do you have an issue tracker?
A: Yeah... madOS issue tracker
Q: What's working ?
A: Check first Post for current status
Q: App "x" doesn't work, why?
A: Probably not compatible with OREO yet, feedback is welcome
Q: Is the rom rooted?
A: NO, But you can easily root with :
1: Magisk ( v14 onwards.)
2: Super SU ( v2.82 onwards)
Q: Should i root together with rom ?
A: Not advised.. mainly the Magisk that gives some weird issues...
Flash ROM and GAPPS (if you use gapps), after first boot get back to recovery and flash your desire rooting method
Q: Does xposed work?
A: Is there Xposed for O? ... then no ;p
Q: How is battery life with Oreo?
A: Pretty awesome
Q: Does this build support Vulkan?
A: No....duh! v
Q: Does doze work in this build?
A: Yup
Q: Does 4k video recording work?
A: Yes, but not every phone supports it. If 4k worked in the stock rom, it will work in madOS too.
Q: when will (feature/issue here) be fixed?
A: NO ETA , please
Porting F.A.Q.
No porting support, no port questions allowed on this thread, and porting PMs will be auto-deleted, porting replies will be reported as well
G.APPS F.A.Q.
Q:What GAPPS package should I use?
A:OpenGapps arm64 nano/mini
Since there's no Official GAPPS for 8.1.0 just yet...
... we had built OpenGapps nano and pico versions
--> Check Download Section
Q: How to properly install GAPPS?
A:Flash Rom + Flash Gapps at once
CREDITS and Thanks
madOS Team
Our translators, credits list here
A.O.S.P.
AOSPA
DU (Dirty Unicorns)
Omni
HELP supporting madOS
We do this on our free time, however we do have costs on maintaining this :/
Any donation is highly appreciated
You can donate by using
this link
If the above doesn't work in your country, then you can directly donate by using this e-mail adress: [email protected]
About madOS Proprietary Apps
You are NOT allowed by any means, to use our madOS apps on any other build, your rom
This is exclusively for OFFICIAL madOS ROM releases
@To Moderators: Feel free to clean the thread, whenever users start spamming, severe OT, or questioning about porting...
Changelogs
[Stable] Build [8.1.0] 20171225
First Release
madOS version: 2.1
Patch Level: 8.1.0 [OPM1] December 5, 2017
Kernel: 3.18.89 (o-8.1.0 branch)
[Stable] Build [8.1.0] 20180102
madOS version: 2.1.1
Fixed UI lags / hangs
Fixed deepsleep
Fixed screen recording
Fixed video playback issues
Updated graphics system
Improved GSM/LTE signal handling
Fixed alarms
Fixed FMRadio
Fixed wallpaper scrolling setting in madLauncher
Fixed 5GHz hotspot issues
Improvements in bluetooth for A2DP
Updated included APNs list
madOS color Engine:
Rebased & many improvements on the engine
Better support on theming Quick Settings
New option to override default Google 8.1 QS theming
New reset button to get back to default 8.1 theming
New MAD mode
Merry Christmas !!
Thanks. Merry Christmas.
The computer died. I will not make the sd card backup.
Marry Xmas to all.
Wow.... Oreo release and directly 8.1 weeeeeeeeeeee!
Didn't expect this before the new year, what a surprise.
Thanx you @fire855
Thank you MAD-team
Hi,
How to install ROM and gapps?
On TWRP or using flash?
Thank you
Should we come from the last 7.1.2 build (which has different partitions from stock)?
I really appreciate the work, but it's somewhat unflashable. New recovery is not stable, it gets stuck sometimes. Also I didn't manage to bring 8.1 to run with Gapps yet.
€: To provide somewhat more information: System crashes when running playstore.
€2: Full wipe made, advanced wipe and wiped every partition. It gets stuck coincidential, there's no proper reason for it, it got stuck once when I flashed MadOS itself, second time it got stuck flashing gapps, so I hope I get it run that night...
€3: Recovery freezes and after 30 seconds (approx) phone reboots.
€4: Nope, I don't get it to work, goddamnit. It freezes almost immediately after I enter my pin.
Help please...
I install new TRWP OREO on old twrp...
when reboot the phone shutoff and does nothing... i cant turn on...
TJFA81 said:
Help please...
I install new TRWP OREO on old twrp...
when reboot the phone shutoff and does nothing... i cant turn on...
Click to expand...
Click to collapse
Hold VOL+ and POWER when rebooting. Then you can choose to boot into TWRP. There you copy the new recovery image and then flash Oreo.
Xorianator said:
Hold VOL+ and POWER when rebooting. Then you can choose to boot into TWRP. There you copy the new recovery image and then flash Oreo.
Click to expand...
Click to collapse
I cant...
When choose recovery the phone freezes. black screen
To install new TWRP OREO its only necessary flash the file recovery.img???
TJFA81 said:
I cant...
When choose recovery the phone freezes. black screen
To install new TWRP OREO its only necessary flash the file recovery.img???
Click to expand...
Click to collapse
Yes, you only have to bring the recovery up again.
What you can also do is: Go back to 7.1 (flash it with SPflashtool) and then do the steps
Xorianator said:
Yes, you only have to bring the recovery up again.
What you can also do is: Go back to 7.1 (flash it with SPflashtool) and then do the steps
Click to expand...
Click to collapse
I cant go to recovery...
Can start the phone but cant go to recovery after flash new recovery file posted on MAD facebook.
I dont have 8.1 because of that, just did the first step anda now cant go to recovery
TJFA81 said:
I cant go to recovery...
Can start the phone but cant go to recovery after flash new recovery file posted on MAD facebook.
I dont have 8.1 because of that, just did the first step anda now cant go to recovery
Click to expand...
Click to collapse
Reflash 7.1 image using SPflashtool, I made a guide for this There you go. Then you can repeat.
Okay so 8.1 is not working at all... I get somewhat a weird failure on screen, the screen "sacks" down (main UI Activity just "fall down", status bar is still up) and then it freezes... Looking forward to get this fixed soon.
€: And the boot time is horrible, before I see a screen it's black for idk 2 Minutes
€3: Nvm lol, actually the phone is now unable to boot in System....
€4: Give it a try with "optional" F2FS File system step, let's see.
€5: Nope, didn't fix a thing. So well, at least I could capture this "sack down" thing:
The red line is where the display ends. As you can see the symbols are still in place. The blue line marks where the activity "sack down" and if this happens (which happens just on coincidence) nothing will happen any further, system's frozen and it reboots afterwards.
TJFA81 said:
Hi,
How to install ROM and gapps?
On TWRP or using flash?
Thank you
Click to expand...
Click to collapse
TWRP
Xorianator said:
Reflash 7.1 image using SPflashtool, I made a guide for this There you go. Then you can repeat.
Okay so 8.1 is not working at all... I get somewhat a weird failure on screen, the screen "sacks" down (main UI Activity just "fall down", status bar is still up) and then it freezes... Looking forward to get this fixed soon.
€: And the boot time is horrible, before I see a screen it's black for idk 2 Minutes
€3: Nvm lol, actually the phone is now unable to boot in System....
€4: Give it a try with "optional" F2FS File system step, let's see.
Click to expand...
Click to collapse
Thank you, already did it... reflash recovery.img but by spflashtool. Now im inside twrp3.2.1...
Now its time to try install oreo and gapps
cedricboquiren said:
Should we come from the last 7.1.2 build (which has different partitions from stock)?
Click to expand...
Click to collapse
Yes, the latest 7.1.2 is mandatory. Added this to the first post now too.
I tried to install the new rom, after I installed the new twrp, the phone is still restarting, I tried to return to 7.1.2 with spft but no success even does not connect with the laptop, what I could do they do?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Code:
/*
* I'm not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed (like it did for me...).
* Please do some research if you have any concerns about features included in the products you find here before flashing it!
* YOU are choosing to make these modifications, and if you point the finger at me for messing up your device, I will laugh at you.
* Your warranty will be void if you tamper with any part of your device / software.
* Same statement for XDA.
*/
LineageOS is a free, community built, aftermarket firmware distribution of Android 10 (Q), which is designed to increase performance and reliability over stock Android for your device.
LineageOS is based on the Android Open Source Project with extra contributions from many people within the Android community. It can be used without any need to have any Google application installed. Linked below is a package that has come from another Android project that restore the Google parts. LineageOS does still include various hardware-specific code, which is also slowly being open-sourced anyway.
All the source code for LineageOS is available in the LineageOS Github repo. And if you would like to contribute to LineageOS, please visit out Gerrit Code Review.
What's working :
Boots
RIL (Calls, SMS, Data)
Wi-Fi
Bluetooth
Camera
Camcorder
Video Playback
Audio
Sensors
Flash
GPS
NFC
Flashlight
Mobicore keystore
Known issues:
VoLTE
Selinux is permissive
Instructions :
If you're on oreo, flash OneUI latest.
Download the latest build.
Reboot to recovery
Flash the latest build.
Optional: Flash GApps for Google Services and Magisk for root.
Reboot
Downloads :
All updates will be here.
Sources :
Device Tree
Common Device Tree
Vendor Blobs
Kernel Source
XDA:DevDB Information
[ROM][UNOFFICIAL][10] LineageOS 17.1 for Galaxy J4+ [j4primelte], ROM for the Samsung Galaxy J4+
Contributors
ataberkozen
Source Code: https://github.com/LineageOS
ROM OS Version: Android 10
ROM Kernel: Linux 3.x
ROM Firmware Required: OneUI, U2
Based On: LineageOS
Version Information
Status: Beta
Current Beta Version: 1.1
Beta Release Date: 2020-02-25
Created 2020-02-25
Last Updated 2020-03-10
Changelogs :
Public Beta 3 - 18/03/2020 :
Fixed a issue which some users have broken ril.
Fixed a issue which some users have broken nfc.
Public Beta 2 - 10/03/2020 :
Merge Security Patch: 5 March 2020
Fix audio on second sim: @Geckyn
Fix HDR on Camera.
Fix FM Radio.
Fix torch releated issues.
Fix Mac Adress releated issues.
LineageOS Source Upstream.
Public Beta 1 - 26/02/2020 :
First public release.
Special Thanks :
@BarryBlackCat for non-stop, day and night testing builds.
@Geckyn for pointing out some stuff. Thanks man.
I will NOT accept your bug report if you are using a custom kernel.
I will NOT accept your bug report if you are using a modification (Like some magisk modules etc.).
I will NOT check your bug report if you didn't provide any logs (Some bugs may will be checked).
Camera doesn't take HDR photo (or hang when switching between HDR and non HDR mode), it also happened on other custom ROM as well.
No magisk module or custom kernel installed.
Here is the logcat with "camera" keyword as filter: https://pastebin.com/RrDvAtjw
Andhika24kd said:
Camera doesn't take HDR photo (or hang when switching between HDR and non HDR mode), it also happened on other custom ROM as well.
No magisk module or custom kernel installed.
Here is the logcat with "camera" keyword as filter: https://pastebin.com/RrDvAtjw
Click to expand...
Click to collapse
Thanks.
KotaMangga said:
Ashyx kernel sir?
Click to expand...
Click to collapse
Let me make the steps clear for you:
1) You must be on Android Pie (custom or stock ROM doesn't matter). If you're on Samsung Oreo (U2), upgrade to Samsung Pie first so the device bootloader will be upgraded to U4 or newer.
2) If you're on Samsung Pie, flash TWRP and do all the required steps (this includes flashing RMM bypass, flashing encryption disabler, and formatting your data). If you're already using custom ROM, just skip this step.
3) Go to TWRP. As far as I remember, you can boot directly to TWRP by pressing POWER + VOL UP when the device is off.
4) In TWRP, swipe to allow modifications. Go to wipe - advanced wipe - and select dalvik/ART, system, data, and cache - swipe to wipe. You may also want to wipe your internal/external storage to avoid dirty data from previous ROM and apps.
5) Go to install - select your ROM zip and flash it - also flash Magisk and GApps after that (if needed)
6) Reboot system. If asked to install TWRP system app, just unselect all checkboxes and press do not install.
7) You're done. First boot will take a while, be patient.
No, kernel is already shipped within the ROM itself. No ROM comes with no kernel (lol). Moreover, most custom kernels on the J4+ forum may not be compatible for Android 10 yet. The OP also stated do not flash custom kernel if you want to get his support. However, if you insisted, make sure to reflash Magisk (if installed before) after flashing custom kernel. Alternatively, flash the custom kernel first before flashing Magisk.
No, OrangeFox recovery is not tested. If you're having trouble flashing the ROM using OrangeFox, unpack TWRP tar file and flash the recovery.img as recovery inside OrangeFox. After reboot, you will have TWRP again as your recovery (press POWER + VOL UP, as stated earlier).
ROM screenshot: (Stock apps are actually there and just like in LOS 16, sorry I already uninstalled most of them)
Andhika24kd said:
Let me make the steps clear for you:
1) You must be on Android Pie (custom or stock ROM doesn't matter). If you're on Samsung Oreo (U2), upgrade to Samsung Pie first so the device bootloader will be upgraded to U4 or newer.
2) If you're on Samsung Pie, flash TWRP and do all the required steps (this includes flashing RMM bypass, flashing encryption disabler, and formatting your data). If you're already using custom ROM, just skip this step.
3) Go to TWRP. As far as I remember, you can boot directly to TWRP by pressing POWER + VOL UP when the device is off.
4) In TWRP, swipe to allow modifications. Go to wipe - advanced wipe - and select dalvik/ART, system, data, and cache - swipe to wipe. You may also want to wipe your internal/external storage to avoid dirty data from previous ROM and apps.
5) Go to install - select your ROM zip and flash it - also flash Magisk and GApps after that (if needed)
6) Reboot system. If asked to install TWRP system app, just unselect all checkboxes and press do not install.
7) You're done. First boot will take a while, be patient.
No, kernel is already shipped within the ROM itself. No ROM comes with no kernel (lol). Moreover, most custom kernels on the J4+ forum may not be compatible for Android 10 yet. The OP also stated do not flash custom kernel if you want to get his support. However, if you insisted, make sure to reflash Magisk (if installed before) after flashing custom kernel. Alternatively, flash the custom kernel first before flashing Magisk.
No, OrangeFox recovery is not tested. If you're having trouble flashing the ROM using OrangeFox, unpack TWRP tar file and flash the recovery.img as recovery inside OrangeFox. After reboot, you will have TWRP again as your recovery (press POWER + VOL UP, as stated earlier).
Click to expand...
Click to collapse
OK , thanks for the tutorial also the full explanation
Can we get some screenshots?
any temp fix for VoLTE and sec sim voice
swarupgolui said:
any temp fix for VoLTE and sec sim voice
Click to expand...
Click to collapse
Maybe you could try sending logcat when attempting voice (call?) on SIM 2. There is a handy app on Play Store called "Logcat Reader" to catch & filter logs easily, just press to round button to record the logs.
I currently can't do it since I don't have someone important to call.
swarupgolui said:
any temp fix for VoLTE and sec sim voice
Click to expand...
Click to collapse
Samsung's ims is heavily OneUI framework dependent. Fixing it is kinda miracle. I don't think it will be ever fixed. But if you contact me on telegram, we might try to fix it. Also trying to fix voice of second sim.
This rom for j6+ sir? , I cant flash it .
KotaMangga said:
This rom for j6+ sir? , I cant flash it .
Click to expand...
Click to collapse
Check the thread on j6+ forum.
ataberkozen said:
Samsung's ims is heavily OneUI framework dependent. Fixing it is kinda miracle. I don't think it will be ever fixed. But if you contact me on telegram, we might try to fix it. Also trying to fix voice of second sim.
Click to expand...
Click to collapse
telegram link?
swarupgolui said:
telegram link?
Click to expand...
Click to collapse
MacTavishAO
ataberkozen said:
MacTavishAO
Click to expand...
Click to collapse
already send the msg reply plz
my id @metalgod_IN
ataberkozen said:
Check the thread on j6+ forum.
Click to expand...
Click to collapse
no, I mean it's for j4+?
E3004 : This package is for j6primelte ; your device is j4primelte.
KotaMangga said:
no, I mean it's for j4+?
E3004 : This package is for j6primelte ; your device is j4primelte.
Click to expand...
Click to collapse
Don't click on "Download Latest Version", click on zip name with j4primelte.
I has installed the rom sir , this rom more faster.
I see little problem :
1. when i change to power saver , battery indicator going red . but after switch mode , its back normal
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today
Features:
https://github.com/crdroidandroid/crdroid_features/blob/10.0/README.mkdn
Flashing Instructions:
Pre-installation:
TWRP (Download from here)
gapps (Download from here)
Magisk 21.0 or newer for root (after first boot) - (Download from here)
First time installation:
You need Unlocked bootloader for install
step 1 Download crDroid from the link, if you want root then download Magisk also and copy it all to your Phone internel or external your choice.
step 2 Go to recovery when you didnt installed it already download it from the listed link, go in fastboot with all 3 keys pressed hold then select with volume keys Download mode and hit power button,
When youre on Windows download adb minimal and fastboot here in https://forum.xda-developers.com/showthread.php?t=2317790 install it , open the shortcut on your desktop if one was created when not just serch in Windows for minimal and you will find it.
step 3 Type in the opened command prompt in minimal adb and fastboot: adb devices to check if device was recognized, when not download here the drivers to make sure it works fine https://downloadmirror.co/1LnA/HTC_Driver_v4.17.0.001.zip?pt=SCTaNyN4GCn3NIchsd7q3hM7hBYxuFbGvjQe9voyZY4= run it let it install then type again fastboot devices make sure you see some numbers like FA53WYJ13710 then it works fine and can start flashing.
step 4 Go to your download folder and search for twrp-3.4.0-0-hima.img rename it to twrp.img to make it easier for you to flash. copy the renamed twrp.img to C:/Program Files (x86)/minmal adb and fastboot/
step 5 Type in your Minimal adb Fastboot prompt: flash recovery twrp.img after OK type fastboot reboot bootloader and select with volume keys recovery and hit power button, congrats youre in TWRP recovery
step 6 Now you can make A backup of all your stuff when you have enough Disk space on your Internal or External storage when not make space on your SDcard or Internal storage and copy all your stoff on your Computer to make Space for a backup of your Data =apps and settings System = current Android. when you have Done that part go to install and select the Download Rom install it and if you want root then also The Magisk.zip props go out to https://forum.xda-developers.com/member.php?u=4470081 thanks to him for for his Makgisk root solution :good: and after all installed hit Reboot
Update installation:
You can dirty flash it if youre on android 10 and youre lucky it will start without apps crashing.
If you dont want to get Dirty then you youre fomat Data and System in TWRP and flash the Rom also you can make a Backup current Rom if you want.
Sources:
ROM: https://github.com/crdroidandroid
Kernel: https://github.com/AICP/kernel_htc_msm8994
Download:
ROM https://www.mediafire.com/folder/gvfujacrh306y/crDroid_10
Version 6.12 is Claymore style version, 6.16 is my style, maybe more performance on cost of battery.
Known issues:
None, tell me
Visit official website @ crDroid.net
crDroid Community Telegram
Donate to help our team pay server costs
Here some pics
Edit: The rom is newer then the pics, this are just Sampels i created a while ago
https://ibb.co/BjCbGCV
https://ibb.co/HXNCPTh
Thanks to:
- Claymore 1297 and his Team for the work on the M9, without him it wouldn't be possible!
- Google
- LineageOS
- SlimRoms
- AOSPA (Paranoid Android)
- OmniRom
- NamelessROM
- Many others... (if you're feeling upset being out of the thanks list just send a PM )
ROM OS Version Android 10
ROM Kernel: Linux 3.x
ROM Firmware Required: 4.x
Based On: Lineage
Version Information
Status: Stable
Created 2020-11-23
Last Updated 2021-05-13
The download link of suggested twrp is here.
tombbb said:
The download link of suggested twrp is here.
Click to expand...
Click to collapse
Its already included in flashing instructions
I clean installed your ROM on my M9, and it's nice!! Thank you!
May I ask will there be build 6.1.3 for m9?
tombbb said:
May I ask will there be build 6.1.3 for m9?
Click to expand...
Click to collapse
I think yes , i will build lastest release and then iam aiminng for Crdroid 7. But for now i have to wait to get my Notebook fixed...
Hi, I try the rom and it's great, all works but signal operator. My broadband comapny is Fastweb (Italy) and the sim is ok, not broken (tested on another HTC One M9). What can it be? Any suggestion?
Thanks in advance
Update (15 Feb 2021)
weird is when I run the phone it ask me for the SIM passoword, so it seems that it seeing by the system but, if I try make a call it say: cellular broadband network not available
Marko Indaco said:
Hi, I try the rom and it's great, all works but signal operator. My broadband comapny is Fastweb (Italy) and the sim is ok, not broken (tested on another HTC One M9). What can it be? Any suggestion?
Thanks in advance
Update (15 Feb 2021)
weird is when I run the phone it ask me for the SIM passoword, so it seems that it seeing by the system but, if I try make a call it say: cellular broadband network not available
Click to expand...
Click to collapse
Ah bro when you want sigal go to APN write something save it , and then it work , its a bug in generell
platinumthis said:
Ah bro when you want sigal go to APN write something save it , and then it work , its a bug in generell
Click to expand...
Click to collapse
I already try it without success. I'll try again in a few hours but I'm feeling that dont works. I wonder what could be. I mean, I use ViperOneM9 on another HTC OneM9 and it's always works fine. No need to set APN or whatever. Even after flash/dirty flash, changing roms and then reisntall ViperOne... the signal always works perfect in this case.
Thank you for reply anyway
Changelog
* Updated to lastest Crdroid and Lineage base
* Tweaked some Performance
* ViperFX Works Out of the Box
Such a good news ! Thank you !
Is dirty flash from 6.12 to 6.16 suggested ?
It has to work when you flash
tombbb said:
Such a good news ! Thank you !
Is dirty flash from 6.12 to 6.16 suggested ?
Click to expand...
Click to collapse
Indeed
platinumthis said:
Indeed
Click to expand...
Click to collapse
I upgraded to 6.16, it is great and stable.
platinumthis said:
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today
Features:
https://github.com/crdroidandroid/crdroid_features/blob/10.0/README.mkdn
Flashing Instructions:
Pre-installation:
TWRP (Download from here)
gapps (Download from here)
Magisk 21.0 or newer for root (after first boot) - (Download from here)
First time installation:
You need Unlocked bootloader for install
step 1 Download crDroid from the link, if you want root then download Magisk also and copy it all to your Phone internel or external your choice.
step 2 Go to recovery when you didnt installed it already download it from the listed link, go in fastboot with all 3 keys pressed hold then select with volume keys Download mode and hit power button,
When youre on Windows download adb minimal and fastboot here in https://forum.xda-developers.com/showthread.php?t=2317790 install it , open the shortcut on your desktop if one was created when not just serch in Windows for minimal and you will find it.
step 3 Type in the opened command prompt in minimal adb and fastboot: adb devices to check if device was recognized, when not download here the drivers to make sure it works fine https://downloadmirror.co/1LnA/HTC_Driver_v4.17.0.001.zip?pt=SCTaNyN4GCn3NIchsd7q3hM7hBYxuFbGvjQe9voyZY4= run it let it install then type again fastboot devices make sure you see some numbers like FA53WYJ13710 then it works fine and can start flashing.
step 4 Go to your download folder and search for twrp-3.4.0-0-hima.img rename it to twrp.img to make it easier for you to flash. copy the renamed twrp.img to C:/Program Files (x86)/minmal adb and fastboot/
step 5 Type in your Minimal adb Fastboot prompt: flash recovery twrp.img after OK type fastboot reboot bootloader and select with volume keys recovery and hit power button, congrats youre in TWRP recovery
step 6 Now you can make A backup of all your stuff when you have enough Disk space on your Internal or External storage when not make space on your SDcard or Internal storage and copy all your stoff on your Computer to make Space for a backup of your Data =apps and settings System = current Android. when you have Done that part go to install and select the Download Rom install it and if you want root then also The Magisk.zip props go out to https://forum.xda-developers.com/member.php?u=4470081 thanks to him for for his Makgisk root solution :good: and after all installed hit Reboot
Update installation:
You can dirty flash it if youre on android 10 and youre lucky it will start without apps crashing.
If you dont want to get Dirty then you youre fomat Data and System in TWRP and flash the Rom also you can make a Backup current Rom if you want.
Sources:
ROM: https://github.com/crdroidandroid
Kernel: https://github.com/AICP/kernel_htc_msm8994
Download:
ROM https://www.mediafire.com/file/gcpqv6fou03pag9/crDroidAndroid-10.0-20210512-hima-v6.18.zip/file
Known issues:
None, tell me
Visit official website @ crDroid.net
crDroid Community Telegram
Donate to help our team pay server costs
Here some pics
Edit: The rom is newer then the pics, this are just Sampels i created a while ago
https://ibb.co/BjCbGCV
https://ibb.co/HXNCPTh
Thanks to:
- Claymore 1297 and his Team for the work on the M9, without him it wouldn't be possible!
- Google
- LineageOS
- SlimRoms
- AOSPA (Paranoid Android)
- OmniRom
- NamelessROM
- Many others... (if you're feeling upset being out of the thanks list just send a PM )
ROM OS Version Android 10
ROM Kernel: Linux 3.x
ROM Firmware Required: 4.x
Based On: Lineage
Version Information
Status: Stable
Created 2020-11-23
Last Updated 2021-05-13
Click to expand...
Click to collapse
Hello, i want revert back version 6.16. It is possible?
6.18 is doing random restarts.
Sure its possible, i wil invetigate and will make a new one when i have time, lets say 10 Days
platinumthis said:
Sure its possible, i wil invetigate and will make a new one when i have time, lets say 10 Days
Click to expand...
Click to collapse
Or use only 6.16 and get there security updates. This version was really crazy in battery life. I remember also some little graphics glitches, mostly with recents, but in overall BEST custom rom for this device.
tombbb said:
I upgraded to 6.16, it is great and stable.
Click to expand...
Click to collapse
Hi Do you have v6.16 of this ROM? If yes, could you please share with us? Thanks
Arsenik013 said:
Hi Do you have v6.16 of this ROM? If yes, could you please share with us? Thanks
Click to expand...
Click to collapse
I once checked last time someone asked, but I don't have it anymore...
I don't see any bad of 7.12, maybe you try sometime?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
crDroid for Samsung Galaxy Note 10/+/+ 5G [d1&d2s&d2x]
Please read whole post before downloading
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
What is this?
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today.
Whats working?
Wifi
RIL
Mobile data
GPS
Camera
Flashlight
Camera
Bluetooth
Fingerprint reader
Face unlock
NFC
Lights
Sound / vibration
FP gestures
Known issues
VoLTE/VoWIFI - not working for most Samsung devices, so no fix in the near future
You tell meDownload: (Always Download the latest)
ROM (d1) (d2s) (d2x)
Recovery (d1) (d2s) (d2x)
Magisk (Download from here)
Gapps - (Download from here) (Use MindTheGapps-13.0.0-arm64*.zip)
First time installation:
The same instructions as for installing official LineageOS apply, so the ones found here.
You CAN NOT install this ROM using TWRP.
You need to use the crDroid Recovery or the Official Lineage Recovery provided by Linux4.
Installing crDroid Recovey (BL already unlocked):Odin:
Rename the downloaded .img to recovery.img and add it to a .tar archive using, for example, 7Zip
Flash the resulting .tar file in Odin
Installing The ROM From crDroid Recovery:
crDroid Recovery - Factory reset > Factory reset & reset system partitions
Make sure that all your zip ready for install via OTG/SD card/ADB
crDroid Recovery - Apply update > Choose from sdcard > select the rom and install it
Install magisk .zip (change magisk.apk to magisk.zip if you installing via SD card/OTG)
Reboot to system!
Version Information
Status: Official
Current Version: January (13.0.0_r20)
Stable Release Date: 13/01/2023
Device Maintainer: @Jubscleisson
Sources&Trees
ROM Source: (Link)
Device tree: (d1) (d2s) (d2x)
Common device tree: (Link)
Kernel: (Link)
Vendor: (d1) (d2s) (d2x)
Credits
@Linux4 - For making the trees and officialy maintaing them in LineageOS, For giving me access to A13 device tree and helping me all time!
Visit official website @ crDroid.net
crDroid Community Telegram
crDroid Updates Channel
Donate to help our team pay server costs
Support Group Link
Thank you for this rom.
Is it encrypted or not please ?
bayad said:
Thank you for this rom.
Is it encrypted or not please ?
Click to expand...
Click to collapse
You're welcome, sir
This version has the encryption working perfectly, to avoid any problems, I ask you to use the recovery of the ROM itself
Jubscleisson said:
You're welcome, sir
This version has the encryption working perfectly, to avoid any problems, I ask you to use the recovery of the ROM itself
Click to expand...
Click to collapse
Thank you for your answer.
About the recovery you are talking about, does it have backup/restore functions like TWRP ?
Hello @Jubscleisson
Many thanks for your efforts.
Does the Rom include Gcam?
How is the sound for music/youtube playback?
Kind regards,
When the One UI 5 coming?
Anyone has any print screens? option menu and so on?pls
bayad said:
Thank you for your answer.
About the recovery you are talking about, does it have backup/restore functions like TWRP ?
Click to expand...
Click to collapse
It doesn't.
bayad said:
Thank you for your answer.
About the recovery you are talking about, does it have backup/restore functions like TWRP ?
Click to expand...
Click to collapse
No, this function does not exist. Even because data partition isn't supposed to be mounted in a recovery anyways.
I ask that you make backups with an app that is convenient for you, something like Swift Backup or use Google's backup service (if you use GApps).
Jubscleisson said:
No, this function does not exist. Even because data partition isn't supposed to be mounted in a recovery anyways.
I ask that you make backups with an app that is convenient for you, something like Swift Backup or use Google's backup service (if you use GApps).
Click to expand...
Click to collapse
I'm already using Swift Backup for my apps but it's annoying that I need to reconfigure every rom settings when switching between roms
The recovery d2s checksum is not right.
When I give this command: heimdall flash --Recovery.img --no-reboot
I get the following error:
ERROR: Partition "Recovery" does not exist in the specified PIT.
Ending session...
Releasing device interface...
Any idea what can happen?
Cosque said:
The recovery d2s checksum is not right.
When I give this command: heimdall flash --Recovery.img --no-reboot
I get the following error:
ERROR: Partition "Recovery" does not exist in the specified PIT.
Ending session...
Releasing device interface...
Any idea what can happen?
Click to expand...
Click to collapse
partition name is --RECOVERY, not --Recovery
the complete command is heimdall flash --RECOVERY recovery.img --no-reboot
Hope this helps
I've already load the crDroid Recovery, I want to be 100% sure of the next steps, as I understand:
1) Format data / factory reset
2) Format system partition
1 and 2 or only 1 ?
Cosque said:
I've already load the crDroid Recovery, I want to be 100% sure of the next steps, as I understand:
1) Format data / factory reset
2) Format system partition
1 and 2 or only 1 ?
Click to expand...
Click to collapse
Both.
PlayStore does not connect to the Internet with: MindTheGapps-13.0.0-arm64-20221025_100653.zip
Using Core from here https://sourceforge.net/projects/nikgapps/files/Releases/NikGapps-T/28-Aug-2022/ works well
Thanks for the rom!
Thank you very much for this rom, it is amazing but I have a problem:
I can't mount the system as read/write to block some services.
can you check for this please??
Jubscleisson said:
crDroid for Samsung Galaxy Note 10/+/+ 5G [d1&d2s&d2x]
Please read whole post before downloading
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
What is this?
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today.
Whats working?
Wifi
RIL
Mobile data
GPS
Camera
Flashlight
Camera
Bluetooth
Fingerprint reader
Face unlock
NFC
Lights
Sound / vibration
FP gestures
Known issues
VoLTE/VoWIFI - not working for most Samsung devices, so no fix in the near future
You tell meDownload: (Always Download the latest)
ROM (d1) (d2s) (d2x)
Recovery (d1) (d2s) (d2x)
Magisk (Download from here)
Gapps - (Download from here) (Use MindTheGapps-13.0.0-arm64*.zip)
First time installation:
The same instructions as for installing official LineageOS apply, so the ones found here.
You CAN NOT install this ROM using TWRP.
You need to use the crDroid Recovery or the Official Lineage Recovery provided by Linux4.
Installing crDroid Recovey (BL already unlocked):Odin:
Rename the downloaded .img to recovery.img and add it to a .tar archive using, for example, 7Zip
Flash the resulting .tar file in Odin
Installing The ROM From crDroid Recovery:
crDroid Recovery - Factory reset > Factory reset & reset system partitions
Make sure that all your zip ready for install via OTG/SD card/ADB
crDroid Recovery - Apply update > Choose from sdcard > select the rom and install it
Install magisk .zip (change magisk.apk to magisk.zip if you installing via SD card/OTG)
Reboot to system!
Version Information
Status: Official
Current Version: November 2022 (13.0.0_r13)
Stable Release Date: 06/12/2022
Device Maintainer: @Jubscleisson
Sources&Trees
ROM Source: (Link)
Device tree: (d1) (d2s) (d2x)
Common device tree: (Link)
Kernel: (Link)
Vendor: (d1) (d2s) (d2x)
Credits
@Linux4 - For making the trees and officialy maintaing them in LineageOS, For giving me access to A13 device tree and helping me all time!
Visit official website @ crDroid.net
crDroid Community Telegram
crDroid Updates Channel
Donate to help our team pay server costs
Support Group Link
Click to expand...
Click to collapse
This is the best version I have found for dx2 I have had no failures and a perfect install running all sorts of apps its very fast and well put together
I will make a donation shortly keep up the great work
Thanks
Tom
Jubscleisson said:
crDroid for Samsung Galaxy Note 10/+/+ 5G [d1&d2s&d2x]
Please read whole post before downloading
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
What is this?
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today.
Whats working?
Wifi
RIL
Mobile data
GPS
Camera
Flashlight
Camera
Bluetooth
Fingerprint reader
Face unlock
NFC
Lights
Sound / vibration
FP gestures
Known issues
VoLTE/VoWIFI - not working for most Samsung devices, so no fix in the near future
You tell meDownload: (Always Download the latest)
ROM (d1) (d2s) (d2x)
Recovery (d1) (d2s) (d2x)
Magisk (Download from here)
Gapps - (Download from here) (Use MindTheGapps-13.0.0-arm64*.zip)
First time installation:
The same instructions as for installing official LineageOS apply, so the ones found here.
You CAN NOT install this ROM using TWRP.
You need to use the crDroid Recovery or the Official Lineage Recovery provided by Linux4.
Installing crDroid Recovey (BL already unlocked):Odin:
Rename the downloaded .img to recovery.img and add it to a .tar archive using, for example, 7Zip
Flash the resulting .tar file in Odin
Installing The ROM From crDroid Recovery:
crDroid Recovery - Factory reset > Factory reset & reset system partitions
Make sure that all your zip ready for install via OTG/SD card/ADB
crDroid Recovery - Apply update > Choose from sdcard > select the rom and install it
Install magisk .zip (change magisk.apk to magisk.zip if you installing via SD card/OTG)
Reboot to system!
Version Information
Status: Official
Current Version: November 2022 (13.0.0_r13)
Stable Release Date: 06/12/2022
Device Maintainer: @Jubscleisson
Sources&Trees
ROM Source: (Link)
Device tree: (d1) (d2s) (d2x)
Common device tree: (Link)
Kernel: (Link)
Vendor: (d1) (d2s) (d2x)
Credits
@Linux4 - For making the trees and officialy maintaing them in LineageOS, For giving me access to A13 device tree and helping me all time!
Visit official website @ crDroid.net
crDroid Community Telegram
crDroid Updates Channel
Donate to help our team pay server costs
Support Group Link
Click to expand...
Click to collapse
Thank you very much for your amazing work.
crDroid the best rom ever
Is there a minimum firmware requirements to boot this rom ?
Now I'm on HVE5.
The NFC and fast charging are not working. Does anyone have them working?
Any idea?
请问当前版本相比之前的版本是续航有明显提升，还是刷屏时间有明显提升。另一个问题是是否有任何内核可用于提高设备的电池寿命