Unbrick from bootloop iteration [CEREUS] Xiaomi Redmi 6 MT6765 - Xiaomi Redmi 6 Questions & Answers

How to UNBRICK when not booting after flashing stuck on fastboot/preloader mode [HELP] [Redmi 6]
I flashed a wrong boot image(boot.img extracted from MIUI Recovery ROM 10.3.5) via fastboot. (patched for magisk 21.4)
My Redmi 6 device is just unlocked its bootloader 4 days ago.
I tried flashing through Mi Flash Tool, but it doesn't detect my device(Vol - button holding down), it shows "find device timeout". Also SP Flash tool also. It shows "STATUS_BROM_CMD_FAIL (0xC0060005)" error.
So I trying to use MTK bypass(See on GitHub: https://github.com/MTK-bypass/bypass_utility )
Skip steps 1-5 after first usage
1. Install python(select "Add Python X.X to PATH")
2. Install libusb-win32
3. Launch filter wizard, click next
4. Connect powered off phone with volume+ button, you should see new serial device in the list. Select it and click install
5. Install pyusb, pyserial, json5 with command:
pip install pyusb pyserial json5
6. Run this command and connect your powered off phone with volume+ button, you should get "Protection disabled" at the end
python main.py
7. After that, without disconnecting phone, run SP Flash Tool
In Step 6,
I got this error while running main.py of MTK bypass in CMD(Admin).
raise RuntimeError(Default config is missing)
RuntimeError Default config is missing
Also tried running this module in Python IDLE.
I used Python 3.7 version in Windows 7 and Python 3.9.4 in Windows 10.
LibUSB device filter installed for the MTK USB Port while the bootloop iteration.
I have fastboot ROM for my device. (I used MIUI 10.3.6 cereus_global_images_V10.3.6.0.OCGMIXM_20190823.0000.00_8.1_global_1c888d5868.tgz ) Latest Fastboot ROM V11.0.5 here. SPD version used is v5.1924.
Anyone know how to solve this problem? Please help?

https://forum.xda-developers.com/t/...-preloader-mode.4000433/page-18#post-84621797

I just tried this method 1 hour ago and it works, you just didn't followed instructions properly.
"RuntimeError Default config is missing" means that you didn't copied default config into brom.bat folder.
You need to copy all files from this archives to folder with brom.bat file.
https://codeload.github.com/MTK-bypass/exploits_collection/zip/1.5
https://codeload.github.com/MTK-bypass/bypass_utility/zip/1.4.1
And after that you need to set connection to COM port because MTK emulates COM port through USB and set bandwidth to the highest possible.

_fizi_ said:
I just tried this method 1 hour ago and it works, you just didn't followed instructions properly.
"RuntimeError Default config is missing" means that you didn't copied default config into brom.bat folder.
You need to copy all files from this archives to folder with brom.bat file.
https://codeload.github.com/MTK-bypass/exploits_collection/zip/1.5
https://codeload.github.com/MTK-bypass/bypass_utility/zip/1.4.1
And after that you need to set connection to COM port because MTK emulates COM port through USB and set bandwidth to the highest possible.
Click to expand...
Click to collapse
Can you mention where is the brom.bat folder?

adhilfuad said:
Can you mention where is the brom.bat folder?
Click to expand...
Click to collapse
I extracted files from exploits_collection.zip into bypass_utility-1.4.1 folder overwriting the README.md file.
Now MTK bypass done and I got protection disabled. But when I trying to flash with SPD, it shows "ERROR : STATUS_STOR_LIFE_EXHAUST (0xC003001D)". I tried UART mode, and changed COM Ports, Also tried without battery (option changed in SPD).
[I tested in windows 7 SP1 64-bit]
Any solution or mistakes?
[But I couldn't test this in Windows 10 because libusb doesn't show my MTK USB Port now]

_fizi_ said:
I just tried this method 1 hour ago and it works, you just didn't followed instructions properly.
"RuntimeError Default config is missing" means that you didn't copied default config into brom.bat folder.
You need to copy all files from this archives to folder with brom.bat file.
https://codeload.github.com/MTK-bypass/exploits_collection/zip/1.5
https://codeload.github.com/MTK-bypass/bypass_utility/zip/1.4.1
And after that you need to set connection to COM port because MTK emulates COM port through USB and set bandwidth to the highest possible.
Click to expand...
Click to collapse

You need mct. Exe
And python
This is cause from error brom.....bla bla In spflashtool

Pake mct mtk, cari di yutup
MOD EDIT: Please post only in English according to the FORUM RULES or at least add an English translation below your foreign language(Google translator for example),translation added below:
Using mctk, search on yutup

Redmi 6 saya juga udah deadboot seminggu an, padahal 2 bulan yg lalu dah kena 250 di repartisi emmc di konter, akhirnya saya cari di yutub gugel, alhamdulillah nemu juga caranya
MOD EDIT: Please post only in English according to the FORUM RULES or at least add an English translation below your foreign language(Google translator for example),translation added below:
My Redmi 6 also has a deadboot for a week, even though 2 months ago I got 250 at the EMMC repartition at the counter, finally I looked for it on Yutub Gugel, thank God I found the way too

Any one help please?
STATUS_DOWNLOAD_EXCEPTION, Flashing started by downloading DA and then stuck and port disappeared(Shows unknown in status bar instead of High Speed). in SP Flash Tool
Redmi 6 device

My Redmi 6 again stuck at Mi Logo. While using normally, it became hang and restarted automatically and stuck at Mi Logo.
I tried to flash device through Mi Flash Tool with login, but device didn't detect in it.
After that tried sp flash tool along with libusb devel filter and MTK bypass through python in UART Mode(detected as MTK USB Port(COM23)).
But first it shows ERROR: STATUS_ERR (0xC0010001). So I unchecked LIB DA Check and Storage Life Cycle Check from Option in SP Flash Tool(I used version v5.19.24)
Everytime tried again with "PROTECTION DISABLED" from MTK Bypass. I have also tried MCT_MTK_BYPASS tool for this along with SP Flash tool. But now it shows STATUS_DOWNLOAD_EXCEPTION, Flashing started by downloading DA and then stuck and port disappeared(Shows unknown in status bar instead of High Speed).
I tried [Hovatek] Xiaomi Redmi 6 DA & Auth but again stuck at Download Boot Loader 0% while flashing. Unchecked Preloader and tried.
Help? What to do with? Is there anyone provide custom DA for Redmi 6(cereus)?

Help me please
My Redmi 6 again stuck at Mi Logo. While using normally, it became hang and restarted automatically and stuck at Mi Logo.
I tried to flash device through Mi Flash (Pro) Tool and After that tried sp flash tool(version v5.19.24) along with libusb devel filter and MTK bypass through python in UART Mode(detected as MTK USB Port(COM23)).
And got "PROTECTION DISABLED" from MTK Bypass. [I have also tried MCT_MTK_BYPASS tool for this along with SP Flash tool].
But it shows "STATUS_DOWNLOAD_EXCEPTION" error in SP flash tool, Flashing started by downloading DA and then stopped and port disappeared(Shows unknown in status bar instead of High Speed). And no error message; so I waited more than 1 hour. No result - not flashing.
But it shows STATUS_BROM_CMD_FAIL in mi flash pro tool with authenticated mi account and now it not showing mi logo too, only charging indicator LED(But port detects when in libusb devel filter)
Help? How to flash or restore in this condition?
FM_ComBoEmmc_UFS_ALL.err error in Mi Flash
FM_ComBoEmmc_UFS_ALL.err error Mi Flash

Related

[Q] How do I root Lenovo S890 (/get MT6577 drivers installed on Win7x64?)

I searched the forums but couldn't find any answers. This is the first time I'm trying to root an android phone. Things are not going well..
I found a page in Indonesian with instruction on how to root my sister's Lenovo S890. My dad bought her one in China, we live in Europe.
We need to get all the Chinese stuff off and install a "regular" Android version with a normal marketplace (read: whatsapp and google and nothing blocked).
The page with instructions is at http://www.duniaku.net/2013/03/30/u...rtisi-internal-storage-lenovo-ideaphone-s890/ I used Google Translate.
What are the steps? First you need to set up some files such as drivers are required to carry out the process of flashing, SP Flash Tool version 3.1222 or higher, because Lenny chipset MTK6577 S890, S890 and file TWRP to also file a Super User and Busybox will be pushed into the system through TWRP. All the files you can download from the following link:
1 Download Driver Lenovo : Extract file. rar it and then click Install_Driver.exe to install drivers into the system. Rather long process, just wait.
2 Download SP Flash Tool : The author gave the newer version, which v3.1224.01. .
3 Download Team Win Recovery Project : TWRP file is specific to the Lenovo S890, so do not try for another Android, although it also MediaTek chipset.
4 Download Super User and Busybox : Will we push into the system through TWRP custom recovery. Download and copy directly to SD Storage / Memory Cards-mu. Place it outside the / root folder or USB Storage Storage SD / USB storage from your Lenovo S890.
5 Download Data Repartition : This file is optional, just download and place it in the root folder Storage SD / USB Storage. Can later be used to repartition the internal memory is too small Lenovo S890. Author will explain at the bottom.
Click to expand...
Click to collapse
I first installed the Lenovo S890 drivers. Clicked "Install anyway" for everything and rebooted. No problems.
But when I connect the phone it's still complaining that it can't find drivers (and I can't find any official drivers on the Lenovo website either)?
I also installed the MT6577 USB VCOM drivers that I found here http://forum.xda-developers.com/showthread.php?t=2206421 (before I did this the SP Flash Tool did nothing).
I enabled USB Debugging mode on the phone, and took out the SIM, the SD card and the battery when I connect it to USB to the PC. I am running Win7x64.
Every time I try to run (step 2) SP Flash tool, it starts downloading fine, but then Win7 'spits out' the phone (I can hear the 'usb device disconnected' sound) and SP Flash Tool obviously stops working then and gives some error.
I think this is because the MediaTek MT6577 USB VCOM drivers somehow refuse to install correctly? It looks like rooting might go well once this driver thing is fixed?
When I force installation of the drivers I get a Code 10 error and a yellow triangle next to the Preloader and the MediaTEL Vcom something USB driver in Windows Device Manager. ( I searched the forums and didn't find a solution for this).
I forced installation by opening Device Manager, click Add, click Add Legacy Hardware - manual - choose the usb2ser_Win764.info file out of the MT6577 USB VCOM drivers folder
This is what's in the .inf file : Is there anything I can change here to force it to work?
[Version]
Signature="$Windows NT$"
Class=Ports
ClassGuid={4D36E978-E325-11CE-BFC1-08002BE10318}
Provider=%MTK%
DriverVer=05/30/2011,1.1123.0
[Manufacturer]
%MTK%=MTK,NTamd64
[MTK.NTamd64]
%MTK6218%=Reader,USB\Vid_0e8d&Pid_0003,USB\Vid_0e8d&Pid_1003
%MTK_COM%=Reader,USB\Vid_0e8d&Pid_0023&MI_00
%MTK_CAT%=Reader,USB\Vid_0e8d&Pid_0023&MI_02
%MTK_PRELOADER%=Reader, USB\Vid_0e8d&Pid_2000
%MTK_SP_DA%=Reader, USB\Vid_0e8d&Pid_2001
[DestinationDirs]
DefaultDestDir=12
[Reader.NTamd64]
Include=mdmcpq.inf
AddReg=Reader.NTamd64.AddReg
CopyFiles=FakeModemCopyFileSection
[Reader.NTamd64.AddReg]
HKR,,DevLoader,,*ntkern
HKR,,NTMPDriver,,usbser.sys
HKR,,EnumPropPages32,,"MsPorts.dll,SerialPortPropPageProvider"
[Reader.NTamd64.Services]
AddService = usbser, 0x00000002, Service_Inst
[SourceDisksNames]
[SourceDisksFiles]
[Service_Inst]
DisplayName = %Serial.SvcDesc%
ServiceType = 1 ; SERVICE_KERNEL_DRIVER
StartType = 3 ; SERVICE_DEMAND_START
ErrorControl = 1 ; SERVICE_ERROR_NORMAL
ServiceBinary = %12%\usbser.sys
LoadOrderGroup = Base
[Strings]
MTK = "MediaTek Inc."
MTK6218 = "MTK USB Port"
MTK_COM = "MTK USB Modem Port"
MTK_CAT = "MTK USB Debug Port"
MTK_PRELOADER = "MediaTek PreLoader USB VCOM Port"
MTK_SP_DA = "MediaTek DA USB VCOM Port"
Serial.SvcDesc = "USB Serial emulation modem driver"
Click to expand...
Click to collapse
How do I stop Windows from ejecting the phone (force it to keep it connected as the MediaTek thingie that seems to work with SP Flash Tool?).
Or is there a better way to get an English Android version on this phone?
When I now try to boot the phone it says
tool dl image fail
uboot is blocking by dl info
Did I (soft)brick it??
Thanks in advance for all the help!!
Giving up
Since this seems to be a less popular phone with very little support available - I'm giving up.
Spent 3 full days on this thing with no results, and I just read the GPS also won't work outside of China either.
Now all I need to do is figure out how to get it out of META mode or Factory mode, and get it to boot back into it's normal Chinese Android system.
katejones said:
Since this seems to be a less popular phone with very little support available - I'm giving up.
Spent 3 full days on this thing with no results, and I just read the GPS also won't work outside of China either.
Now all I need to do is figure out how to get it out of META mode or Factory mode, and get it to boot back into it's normal Chinese Android system.
Click to expand...
Click to collapse
Hi, I'm having a much similar problem, since I couldn't flash recovery with SP flash tool, the process was terminated unexpectedly showing error message s_ft_need_download_all_fail (4050), after a couple of days looking for a solution I decided to format the phone with SP Flash Tool, and it worked, right after I tried to flas recovery again...and it worked. I thought I had found the way but when I tried to boot the phone in recovery mode nothing happened, no matter what keys combination I use, how long I press them, the phone just won't react, it doesn't show anything on the screen.
I don't know if this was the logic step to follow, but if you want to try and discover what to do next, up to you, 4 hands are better than 2,maybe yuo find the solution.
Good luck.
There is no button combination to boot recovery, try droidgram-reboot on play store.
Sent from my Lenovo S880
Hope you guys manage to root it soon as I am one of those who waiting for it as I need to root my S890 also.
Sent from my Lenovo S890 using xda app-developers app
katejones said:
I searched the forums but couldn't find any answers. This is the first time I'm trying to root an android phone. Things are not going well..
I found a page in Indonesian with instruction on how to root my sister's Lenovo S890. My dad bought her one in China, we live in Europe.
We need to get all the Chinese stuff off and install a "regular" Android version with a normal marketplace (read: whatsapp and google and nothing blocked).
The page with instructions is at http://www.duniaku.net/2013/03/30/u...rtisi-internal-storage-lenovo-ideaphone-s890/ I used Google Translate.
I first installed the Lenovo S890 drivers. Clicked "Install anyway" for everything and rebooted. No problems.
But when I connect the phone it's still complaining that it can't find drivers (and I can't find any official drivers on the Lenovo website either)?
I also installed the MT6577 USB VCOM drivers that I found here http://forum.xda-developers.com/showthread.php?t=2206421 (before I did this the SP Flash Tool did nothing).
I enabled USB Debugging mode on the phone, and took out the SIM, the SD card and the battery when I connect it to USB to the PC. I am running Win7x64.
Every time I try to run (step 2) SP Flash tool, it starts downloading fine, but then Win7 'spits out' the phone (I can hear the 'usb device disconnected' sound) and SP Flash Tool obviously stops working then and gives some error.
I think this is because the MediaTek MT6577 USB VCOM drivers somehow refuse to install correctly? It looks like rooting might go well once this driver thing is fixed?
When I force installation of the drivers I get a Code 10 error and a yellow triangle next to the Preloader and the MediaTEL Vcom something USB driver in Windows Device Manager. ( I searched the forums and didn't find a solution for this).
I forced installation by opening Device Manager, click Add, click Add Legacy Hardware - manual - choose the usb2ser_Win764.info file out of the MT6577 USB VCOM drivers folder
This is what's in the .inf file : Is there anything I can change here to force it to work?
How do I stop Windows from ejecting the phone (force it to keep it connected as the MediaTek thingie that seems to work with SP Flash Tool?).
Or is there a better way to get an English Android version on this phone?
When I now try to boot the phone it says
tool dl image fail
uboot is blocking by dl info
Did I (soft)brick it??
Thanks in advance for all the help!!
Click to expand...
Click to collapse
please use S890_Customized_SP_Flashtool_20121119(v3.1238.5)
flash again ok
i am solve same your problem
https://www.dropbox.com/s/pwvg553v5z1vtju/S890_Customized_SP_Flashtool_20130109(v3.1238.5).rar
kyaw8719 said:
please use S890_Customized_SP_Flashtool_20121119(v3.1238.5)
flash again ok
i am solve same your problem
https://www.dropbox.com/s/pwvg553v5z1vtju/S890_Customized_SP_Flashtool_20130109(v3.1238.5).rar
Click to expand...
Click to collapse
Thanks for sharing. Is it 100% working or still in testing phase?
Sent from my Lenovo S890 using xda app-developers app
nakTT said:
Thanks for sharing. Is it 100% working or still in testing phase?
Sent from my Lenovo S890 using xda app-developers app
Click to expand...
Click to collapse
i fix 2pcs
kyaw8719 said:
i fix 2pcs
Click to expand...
Click to collapse
Meaning?
Sent from my ST26i
doesn't solve the problem
nakTT said:
Meaning?
Sent from my ST26i
Click to expand...
Click to collapse
It doesn't work same problem downloaded the latest SP Flash from the post doesn't work either.. Is there any of you solved the problem? If so then please go detailed about it.

infinix note 3 and note 3 pro

in the name of allh
Infinix Note 3 Pro X601 or infinix note 3 pro
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Review the phone
1- root the phone
How to Root Infinix Note 3 X601/Pro X537 and Port TWRP Recovery Image
Infinix Note 3 and its Pro version are the latest phones from Infinix mobility, though the pro version is not yet available in Nigeria. This article will guide you on how to easily install/port twrp recovery and root infinix Note 3 X601 and Note 3 X537.
Requirements
1-twrp from here "note 3 and note 3 pro "
2- sp flash tool here
3-USB Vcom here
4- super user here
5- pc
6- usb cabel
ltes go >>>
First, install the Mediatek Vcom driver on your computer.
Mediatek USB Vcom Drivers: Download and Manually Install MTK Preloaded USB VCOM Port Drivers on Windows 10/8.1/8/7/Vista/Xp.
Mediatek is one of the most popular and used mobile chipset, it powered numerous Android smartphones especially those produce by Chinese companies. MTK devices are easier to root and changing of IMEI on them is super easy when compared to other chipset. This article will guide you on how to install mediatek USB vcom drivers on any windows computer/Pc which include Windows 7, 8, 8.1, Vista, Xp and Windows 10.
Vcom driver is an essential tool that must be installed on your Windows PC before you can flash a custom ROM, install firmware upgrade or most importantly when trying to unbrick your mediatek device. Without mediatek USB Vcom Drivers properly installed on your Windows 10 computer, SP Flash tool or any other recommended tool will not be able to detect your MTK device like Tecno, Infinix, InnJoo, Xiaomi, Gionee etc. Without these tools detecting your device, there won’t be flashing or upgrading of ROM.
Now that you know why installation of Mediatek Preloaded USB Vcom port driver on your Windows Pc is important, below are the necessary things you should do before initiating the installation process.
1.) Disable driver signature enforcement: It is a security measures Microsoft put in place to avoid installation of unsigned/unrecognized drivers. Since Mediatek USB vcom drivers is not digitally signed, you have to permanently or temporarily disable it before you can install MTK Preloaded USB Vcom driver. To avoid to much digression, please check our previous post for this guide.
2.) Computer: Your Pc must be running either Windows 10, 7, 8.1, 8, Vista or XP to install the MTK preloaded driver.
3.) Mediatek USB Vcom Drivers: Off course you have to download the driver before you can install it. Visit (https://www.datafilehost.com/d/309cd7f0) to download MTK port driver. Works for all MTK65XX including MTK6582, MTK6592 /MTK6589 / MTK6577.
4.) Guide: To have a successful Installation of MTK Vcom Port driver, follow the steps below thoroughly.
How to Install Mediatek USB Vcom Drivers on Any Windows Pc.
Step 1: I will assume you have already downloaded mediatek usb vcom drivers from the URL posted above. Extract it content to your desktop using WinZip, 7Zip or any extracting software installed on your Pc.
Step 2: Hold Win + R key to launch the Run dialogue box >> type devmgmt.msc and click on OK or hit Enter key to open up Device Manager. Alternatively, you can also open Control panel >> Search for Device manager >> Double click to open it. Windows 10 users can also right click on the start menu and click on Device Manager.
Step 3: Click on your Computer name or any other installed driver >> Click on the Action tab >> Select Add Legacy Hardware.
Step 4: A new Windows will Pop saying Welcome to the Add Hardware wizard, Click on Next.
Step 5: From the new page, select the second option that says Install the hardware that I manually select from a list (Advanced), then click on Next.
Step 6: On the Next screen, make sure the Show All Devices option is selected and click on Next.
Step 7: Click on Have Disk on the Next Screen >> Then click on Browse >> navigate to desktop or the folder you extracted the Vcom drivers into.
Step 8: Open it and navigate to USB VCOM drivers >> Select your version of Windows >> Select your System type either 32 bit or 64 bit >> Click on Open. Windows 8, 8.1 and 10 users should select Win 7
Step 9: On the next screen, select MediaTek Preloader USB VCOM Port and click on Next. Click on Next again to initiate the installation process and select Install this driver software anyway when prompt.
Step 10: Wait for few seconds for the installation to complete. You might see error like this device cannot start. (Code 10), ignore and click on Finish.
That’s it, Mediatek USB Vcom Drivers has been successfully installed on your Windows PC. You can proceed to flashing of Custom or Stock ROM, upgrading of firmware and unbricking of any bricked MTK device.
- Start by extracting the TWRP recovery file for your Note 3 Pro to your folder of choice. Am assuming you already downloaded the specific one from the links provided above.
-Then extract the SP flash tool also to a folder of your choosing then run the run the flash_tool.exe as administrator.
-Open the extracted SP flash tool folder, locate the SP flashtool .exe file and run it as an administrator, click the scatter-loading or browse option, depending on the sp flash tool in use, then navigate to the extracted TWRP recovery folder and select the txt recovery image for your device labeled scatter.txt.
-Once it loads up, Untick all the other options as you don’t need them and only select recovery.
-Before going to the next step, make sure you have turned on USB debugging on your device. You can do that by navigating to the Settings then Developer Options. Turn it on by checking the box after USB DEBUGGING.
-Turn off your phone, click the Download button of the SP flash tool. Connect the device to your computer using the USB cable from the manufacturer and the download will start.
-The process of installing the TWRP recovery tool on your device will begin and end when you see a green button. Unplug your device.
That is the first stage. The next stage is the most important so stay attentive.
Step 2: How to root Infinix Note 3 Pro
-The first stage is moving the SuperSu.Zip file to the internal memory of your device or to an SD card in your phone. Advised to copy it to the main folder.
-Boot your phone into recovery mode. You can do that by pressing and holding the power and volume up buttons together. In this mode, your arrow keys will be the volume keys while your power button the selection tool.
-From the options on the screen, choose to install from sd card.
-Locate the SuperSu.Zip file then select it using the power button.
-The process of rooting and flashing your phone will begin after the selection of this file.
-Following the completion of the installation of the SuperSu.Zip file, reboot your device using the power button.
Congratulations, you have just rooted your Infinix Note 3 (Pro)! You may have noticed that to root Infinix Note 3 Pro requires two main stages. Be sure you follow them strictly since they only work in that order.
Note: Incase you brick your infinix note 3 or note 3 pro phone in the process and you are unable to power it on, you can download the INfinix Note 3 Romor here and note 3 pro rom and flash it on your phone using the Infinix SP flash tool downloaded above to restore your phone. Make sure you use the specific Rom to your NOTE 3 phone.
​
the end i hope some one here made a cus rom for the phone .
Important
Already tried this method 2 weeks ago , I would like to add that , you have to flash the su zip file after flashing the custom recovery whatever it was , (I installed CTM recovery),to avoid the boot loop, don't start you device , just flash the su zip after the recovery
I HAVE A PECULIAR PROBLEM! I have an Infinix Note 3 X601, updated to Android N, Rooted and Philz Touch 6. 59, 0 custom recovery installed. Problem began when I tried to factory reset it from within the settings, the phone rebooted to recovery to wipe the data, and since then it wont boot to system again, whenever i try to boot it to system, it will go to recovery. if i connect it to pc, the pc wont recognise it, the pc will show a message that the USB device is not recodnisd, and the phone will boot to recovery again.
i tried to reflash the stock firmware using sp flashtool and it always fails as the system will not recognise the phone, even though i have the required mtk drivers installed.
i tried to flash this https://androidhq254.blogspot.com.ng...te-3-x601.html and http://bbs.infinixmobility.com/thread-149453-3-1.html custom roms using the custom recovery, they all fail mid way.
i will appreciate any help i can get in reviving this phone. thanks in advance
P.S
when i try to flash a rom through recovery it shows:
mount system partition
mount: failed to mount /dev/block/platform/mtk-mdc.0/11230000.mdc.0/by-name/system at /system: no such file or directory
unmount system partition
unmount of /system failed: no such volume
format system partition
E:Error in /storage/sdcard/........
(status0)
installation aborted
what do you make of this pls?
degreatone said:
I HAVE A PECULIAR PROBLEM! I have an Infinix Note 3 X601, updated to Android N, Rooted and Philz Touch 6. 59, 0 custom recovery installed. Problem began when I tried to factory reset it from within the settings, the phone rebooted to recovery to wipe the data, and since then it wont boot to system again, whenever i try to boot it to system, it will go to recovery. if i connect it to pc, the pc wont recognise it, the pc will show a message that the USB device is not recodnisd, and the phone will boot to recovery again.
i tried to reflash the stock firmware using sp flashtool and it always fails as the system will not recognise the phone, even though i have the required mtk drivers installed.
i tried to flash this https://androidhq254.blogspot.com.ng...te-3-x601.html and http://bbs.infinixmobility.com/thread-149453-3-1.html custom roms using the custom recovery, they all fail mid way.
i will appreciate any help i can get in reviving this phone. thanks in advance
P.S
when i try to flash a rom through recovery it shows:
mount system partition
mount: failed to mount /dev/block/platform/mtk-mdc.0/11230000.mdc.0/by-name/system at /system: no such file or directory
unmount system partition
unmount of /system failed: no such volume
format system partition
E:Error in /storage/sdcard/........
(status0)
installation aborted
what do you make of this pls?
Click to expand...
Click to collapse
Brother, solve this problem in the drivers of mobile I advise you to download a new Windows and setup drivers and sp flsh tool
PLS File Name Is TWRP_X601-H536-Note3.rar Is It Work For H537 (Note 3 Pro) Also ?
I m using note 3 pro running nougats
I have tried to root using above method and got OK sign on sp flash tool.. after that when i try to restart in recovery mode its always restart in stock recovery instead of twrp or other
Kindly help as i have to root my device in any way
komalsaeed said:
I m using note 3 pro running nougats
I have tried to root using above method and got OK sign on sp flash tool.. after that when i try to restart in recovery mode its always restart in stock recovery instead of twrp or other
Kindly help as i have to root my device in any way
Click to expand...
Click to collapse
Is your problem solved now? I also have infinix note 3 pro using crlivtouch recovery and everything is ok
Any Custom Rom For X601 PLS Or How To Port Any Rom For This Device @elbana10
other link for super su please
Hi,
I would like to ask about my note 3 pro infinix
my phone was fine till I fine HD games. felt so slow and lag.
so I decided to root it by myself
I wasnt back up the ROM early. its my first time to root mediatek device..
in the middle of processing with flash tool. I "accidentally" klik format+download which made my phone dead.
I was frustated for 2 day to ressurect the phone. I searched for the ROM to flash it again. many ROM I tried. but then I found one. and my phone live again.
but then I notice there's was some error
1. wifi error NVRAM 0x10
2. battery is draining fast in idle state
so then I ask someone to root my phone. because rooting infinix note 3 pro is a pain. I got problem with some TWRP recovery booting. (when I press volume up + power button it wont boot the TWRP recovery,neither CTR).
and then my phone was rooted.
I tried to fix about NVRAM error WIFI with some tutorial in XDA forum . then it fixed
but the battery issue still there. I tried to calibrate it with some root apps,tried to empty to 0% and charge it to 100%, and I tried Lspeed app and HEBF app but the battery still a pain for idle state.
I notice it drops 30% - 40% per night (about 6 hours)
and I notice theres is an error. my SIM2 IMEI is wrong.
how can I fix the battery ?
before I bricked it the battery was super save. when I ressurect it the battery is a pain for idle state.
did I flash a wrong ROM
It was my fault I didnt back up the ROM
and didn't save the build number
I lives in Indonesia. so flash ROM for Indonesia
I got that ROM from Xclub forum
but the battery issue wont solve
please help
Lordgfreeze said:
Is your problem solved now? I also have infinix note 3 pro using crlivtouch recovery and everything is ok
Click to expand...
Click to collapse
Yes its aright now using CTR. Pretty easy to use. Thank you

Indian letv leeco max x900 hard brick resolved (now how to install eui 5.8/android6?)

Hello dear all,
after a long time of rush around different solutions I finally figure it out how to hard brick Indian le max x900
(note hard brick means ur phone is completely dead no charging,no restart, no fastboot etc....becoz of may be wrong rom flashing)
1. Install qualcom driver and latest qpst 2.7 (link: https://androiddatahost.com/np4wq)(qualcomm driver present in qfil file for x800 link in step4)
2. Installed qpst will be present at c:/program files(x86)/qualcomm/qpst/bin....inside it find qfil flashing application...open it
3. connect ur dead indian le max to computer and see if qualcomm usb driver can detect it(u may notice qfil flashing appln will also show some com no connected)....if u r unsuccessful just press both volume key/or power key and both vol key at a time for around 1 min when phone is connected to pc. (in any case u failed no big issue try to install it manually by searching in google, well I have used win10 and it simply worked for me)
4. Download the qfil file for x800 and extract it somewhere, it also have qualcomm driver inside it so once extracted install that driver too (link: https://mega.nz/#!G0ozxZwb!vowHBNjQGC1AtVOx2ThrWpYt6yHEnAACFvq90XDF4n0)....actually i tried qfil for x900,x1, line brush tutorials etc but none of those worked for me and x800 aks le 1 pro have the same processor so it can make x900 alive....sahara error all the time... ( a big thx to UNBRICK X800 X900 Started by mxmax in leeco.re)
5. if all done correctly u can see ur dead indian lemax phone connected to qualcomm mode with some com no, that u can notice in qfil flashing appln.
6.in the flashing appln select Flat Build,
in browse select ur extracted qfil x800 folder (path\qfil x800\x1_na_dvt1_fastboot\prog_emmc_firehose_8994_lite.mbn,
in load xml select rawprogram_unsparse (present inside folder x1_na_dvt1_fastboot)....after that patch0 that automatically comes,
than finally click on download....u can see process started and once completed exit it.
7. So now ur phone have qfil of x800 flashed, try to boot it by pressing power button for 1 min.....u can see blue led blinked and ur phone start to boot (if not means ur phone's battery is very less simply connect it with charger by pressing power button u can see phone starts to show orange led flashing after some time....ie it start charging)
8. once it start in step 7 the phone show chinese letv logo...but it doesn't boot becoz it is for x800 not x900....phone simply tries to boot again and again...so once the phone start to reboot by itself simply press power button and vol down key at a time....u can see small penguin that means ur phone is in fastboot mode.
9. its time now to install twrp 3.0 to ur x900 connected to pc in fastboot mode(link: https://www.androidfilehost.com/?fid=24533103863139522)...simply install twrp from link extract it open the twrp installer appln ....and install it by pressing backspace key that u find during instrution)....great thing about twrp recovery is it can charge ur phone too while connected to power source.
10.So after step 9 ur phone should be in twrp 3.0 recovery mode....u can see internal storage of it shows in pc of around 10 gb not 52 gb.....so inside twrp\wipe\format data...type yes, and advanced wipe select all and wipe......once done u have 52 gb avail in internal storage that u can see in ur pc too.
11. put indian version any rom inside ur internal storage and flash it...once done ur phone will successfully rebooted links for roms are below...simply download any as per ur choice
https://drive.google.com/file/d/0B6m-wM0vYiL8U0U4cUhUM2NlMGc/view (this is stock 12s rom)
https://www.androidfilehost.com/?fid=24533103863139959 (this is also stable 12s rom made bu cuoco with extra settings and dolby presinstalled)
http://evolutionletvx900.blogspot.in/ (this will give u link for 12s and 13s rom which have nova and google launcher preinstalled)
flash any rom and if any any file after flashed make big vibrate ur phone with blue led on...don't panic...simply press power button for long time it will reboot ur phone
I request to make support for Indian x900 also since we cant able to install eui 5.8 based roms....tried to install several roms by deleting lines for check in update-script...even though it installed make it brick/dead again...so plz help for android 6
It Stuck in Leeco logo powered by android
Hello Rahul Raj
Thanks for the instructions to hard brick LeMax X900
I have done as per the instructions provided by you. But it boots and it get stuck in the leeco powered by android in display it never goes further. Please let me know what is the issue.
Rahulraj2012 said:
Hello dear all,
after a long time of rush around different solutions I finally figure it out how to hard brick Indian le max x900
(note hard brick means ur phone is completely dead no charging,no restart, no fastboot etc....becoz of may be wrong rom flashing)
1. Install qualcom driver and latest qpst 2.7 (link: https://androiddatahost.com/np4wq)(qualcomm driver present in qfil file for x800 link in step4)
2. Installed qpst will be present at c:/program files(x86)/qualcomm/qpst/bin....inside it find qfil flashing application...open it
3. connect ur dead indian le max to computer and see if qualcomm usb driver can detect it(u may notice qfil flashing appln will also show some com no connected)....if u r unsuccessful just press both volume key/or power key and both vol key at a time for around 1 min when phone is connected to pc. (in any case u failed no big issue try to install it manually by searching in google, well I have used win10 and it simply worked for me)
4. Download the qfil file for x800 and extract it somewhere, it also have qualcomm driver inside it so once extracted install that driver too (link: https://mega.nz/#!G0ozxZwb!vowHBNjQGC1AtVOx2ThrWpYt6yHEnAACFvq90XDF4n0)....actually i tried qfil for x900,x1, line brush tutorials etc but none of those worked for me and x800 aks le 1 pro have the same processor so it can make x900 alive....sahara error all the time... ( a big thx to UNBRICK X800 X900 Started by mxmax in leeco.re)
5. if all done correctly u can see ur dead indian lemax phone connected to qualcomm mode with some com no, that u can notice in qfil flashing appln.
6.in the flashing appln select Flat Build,
in browse select ur extracted qfil x800 folder (path\qfil x800\x1_na_dvt1_fastboot\prog_emmc_firehose_8994_lite.mbn,
in load xml select rawprogram_unsparse (present inside folder x1_na_dvt1_fastboot)....after that patch0 that automatically comes,
than finally click on download....u can see process started and once completed exit it.
7. So now ur phone have qfil of x800 flashed, try to boot it by pressing power button for 1 min.....u can see blue led blinked and ur phone start to boot (if not means ur phone's battery is very less simply connect it with charger by pressing power button u can see phone starts to show orange led flashing after some time....ie it start charging)
8. once it start in step 7 the phone show chinese letv logo...but it doesn't boot becoz it is for x800 not x900....phone simply tries to boot again and again...so once the phone start to reboot by itself simply press power button and vol down key at a time....u can see small penguin that means ur phone is in fastboot mode.
9. its time now to install twrp 3.0 to ur x900 connected to pc in fastboot mode(link: https://www.androidfilehost.com/?fid=24533103863139522)...simply install twrp from link extract it open the twrp installer appln ....and install it by pressing backspace key that u find during instrution)....great thing about twrp recovery is it can charge ur phone too while connected to power source.
10.So after step 9 ur phone should be in twrp 3.0 recovery mode....u can see internal storage of it shows in pc of around 10 gb not 52 gb.....so inside twrp\wipe\format data...type yes, and advanced wipe select all and wipe......once done u have 52 gb avail in internal storage that u can see in ur pc too.
11. put indian version any rom inside ur internal storage and flash it...once done ur phone will successfully rebooted links for roms are below...simply download any as per ur choice
https://drive.google.com/file/d/0B6m-wM0vYiL8U0U4cUhUM2NlMGc/view (this is stock 12s rom)
https://www.androidfilehost.com/?fid=24533103863139959 (this is also stable 12s rom made bu cuoco with extra settings and dolby presinstalled)
http://evolutionletvx900.blogspot.in/ (this will give u link for 12s and 13s rom which have nova and google launcher preinstalled)
flash any rom and if any any file after flashed make big vibrate ur phone with blue led on...don't panic...simply press power button for long time it will reboot ur phone
I request to make support for Indian x900 also since we cant able to install eui 5.8 based roms....tried to install several roms by deleting lines for check in update-script...even though it installed make it brick/dead again...so plz help for android 6
Click to expand...
Click to collapse
Hi,
Please share me ur qfile and installation method.
i getting sahara error...
my max 1 bricked...
Help
Please i have done it perfectly but my phone is 128GB after unbrick it available storage is 8gb but I don't have any files in the phone to delete so please help me to space my phone if any idea to free it please help
Rahulraj2012 said:
Hello dear all,
after a long time of rush around different solutions I finally figure it out how to hard brick Indian le max x900
(note hard brick means ur phone is completely dead no charging,no restart, no fastboot etc....becoz of may be wrong rom flashing)
1. Install qualcom driver and latest qpst 2.7 (link: https://androiddatahost.com/np4wq)(qualcomm driver present in qfil file for x800 link in step4)
2. Installed qpst will be present at c:/program files(x86)/qualcomm/qpst/bin....inside it find qfil flashing application...open it
3. connect ur dead indian le max to computer and see if qualcomm usb driver can detect it(u may notice qfil flashing appln will also show some com no connected)....if u r unsuccessful just press both volume key/or power key and both vol key at a time for around 1 min when phone is connected to pc. (in any case u failed no big issue try to install it manually by searching in google, well I have used win10 and it simply worked for me)
4. Download the qfil file for x800 and extract it somewhere, it also have qualcomm driver inside it so once extracted install that driver too (link: https://mega.nz/#!G0ozxZwb!vowHBNjQGC1AtVOx2ThrWpYt6yHEnAACFvq90XDF4n0)....actually i tried qfil for x900,x1, line brush tutorials etc but none of those worked for me and x800 aks le 1 pro have the same processor so it can make x900 alive....sahara error all the time... ( a big thx to UNBRICK X800 X900 Started by mxmax in leeco.re)
5. if all done correctly u can see ur dead indian lemax phone connected to qualcomm mode with some com no, that u can notice in qfil flashing appln.
6.in the flashing appln select Flat Build,
in browse select ur extracted qfil x800 folder (path\qfil x800\x1_na_dvt1_fastboot\prog_emmc_firehose_8994_lite.mbn,
in load xml select rawprogram_unsparse (present inside folder x1_na_dvt1_fastboot)....after that patch0 that automatically comes,
than finally click on download....u can see process started and once completed exit it.
7. So now ur phone have qfil of x800 flashed, try to boot it by pressing power button for 1 min.....u can see blue led blinked and ur phone start to boot (if not means ur phone's battery is very less simply connect it with charger by pressing power button u can see phone starts to show orange led flashing after some time....ie it start charging)
8. once it start in step 7 the phone show chinese letv logo...but it doesn't boot becoz it is for x800 not x900....phone simply tries to boot again and again...so once the phone start to reboot by itself simply press power button and vol down key at a time....u can see small penguin that means ur phone is in fastboot mode.
9. its time now to install twrp 3.0 to ur x900 connected to pc in fastboot mode(link: https://www.androidfilehost.com/?fid=24533103863139522)...simply install twrp from link extract it open the twrp installer appln ....and install it by pressing backspace key that u find during instrution)....great thing about twrp recovery is it can charge ur phone too while connected to power source.
10.So after step 9 ur phone should be in twrp 3.0 recovery mode....u can see internal storage of it shows in pc of around 10 gb not 52 gb.....so inside twrp\wipe\format data...type yes, and advanced wipe select all and wipe......once done u have 52 gb avail in internal storage that u can see in ur pc too.
11. put indian version any rom inside ur internal storage and flash it...once done ur phone will successfully rebooted links for roms are below...simply download any as per ur choice
https://drive.google.com/file/d/0B6m-wM0vYiL8U0U4cUhUM2NlMGc/view (this is stock 12s rom)
https://www.androidfilehost.com/?fid=24533103863139959 (this is also stable 12s rom made bu cuoco with extra settings and dolby presinstalled)
http://evolutionletvx900.blogspot.in/ (this will give u link for 12s and 13s rom which have nova and google launcher preinstalled)
flash any rom and if any any file after flashed make big vibrate ur phone with blue led on...don't panic...simply press power button for long time it will reboot ur phone
I request to make support for Indian x900 also since we cant able to install eui 5.8 based roms....tried to install several roms by deleting lines for check in update-script...even though it installed make it brick/dead again...so plz help for android 6
Click to expand...
Click to collapse
the rom is X900 android 6 google play store , it will help you .
https://www.needrom.com/download/le...languages-rom-unbrick-firmware-qfil-fastboot/
tony770101 said:
the rom is X900 android 6 google play store , it will help you .
https://www.needrom.com/download/le...languages-rom-unbrick-firmware-qfil-fastboot/
Click to expand...
Click to collapse
he is protected it with password do you have pass word please
Prefect solution for bricks or le max x900
Bhai aapka jitna shukriya kya jaaye kam h kya jabardust link diya h Na Qualcomm ki jarurat Na qpst ki ek hi link me sab kuch
I have flash three time wrong rom
But your link is really great full
Thanks
Thanks a lot big B ?
Pls provide me max x900 stock rom there link is show corrupt file thanx
not working error sahara
stefdfghhfdf said:
not working error sahara
Click to expand...
Click to collapse
This Sahara Protocol error is really a nasty one. The only way I was able to avoid it was to perform fresh Windows 7 installation on another notebook and install the flashing apps there. I've tried on 5 different Windows 10 systems and it never worked on them. But now I'm fighting with finding the proper ROM for the 128GB X900 version. All the ROMs I've installed so far are bricking again the phone.
I have tried 4 different computers with different os, windows 7 32bit, 64bit and windows 10 64bit, 2 notebook fresh install windows 7 32bit and windows 10 64bit still get sahara error, it seems it won't run as firehose mode, it needs somethimg to switch to make firehose mode on my x900+
Needs help would be appreciated
leeco max x900
I have a leeco max x900 and it died, maybe you need help unbrick, thank you very much

Root LG K41S + SafetynetAPI pass

​Disclaimer​​
These kind of modifications are not for the faint of heart!!! Flash/modify at your own risk!!! I will not be responsible for bricked phones, Dead batteries, world war 3, yada yada yada..... you Know the Rest. ​
Click to expand...
Click to collapse
​Introduction​​
After finding this amazing device (LKM-EMW) for a very cheap price (90 euros new), I made the fatal mistake of updating through OTA to the Latest Android 10 version 00f.
So where is the Problem?? The latest .DZ from the KDZ firmware wasn't extractable through any tool or script I could find anywhere online, Only the Android 9 ROM was working, but Downgrading through LGUP or LG Flash tool was very risky!!!! (due to ARB protection).
Since this phone's Fastboot mode was replaced with LG's own DOWNLOAD mode, using Fastboot commands to flash the Magisk's patched boot image was impossible. QFIL was also not a possibility, Considering it ships with a MTK chipset, and using SP flash tool will require This phone's particular Scatter file and a signed DA from LG to work, leaving me with no other choices for obtaining Root access.
That is, until I found the following tool: mtkclient by bkerler.
Prerequisites​
backup of your DATA. (during and after unlocking the Bootloader, your data partition must be wiped!!!!)​
Preferably a Windows PC (you will need LGUP in case something goes wrong anyways).​
MTK ALL-in-one 1.0.8 drivers and LG's drivers installed.​
mtkclient installed and running (don't ask me how-to, the Github page is pretty self explanatory).​
This Magisk Alpha Build patched for MTK downloaded for installation.
Since this device uses an A/B partitioning system, you need to know which slot is the active one. Using this App, under the System tab, you can find out which one is active. Mine was _b slot.​
and above all.... Patience.​
Unlocking the Bootloader​
(please note, using python [command] didn't work for me for some reason. However, using py [command] worked for me. Use what works!)​
Turn on OEM Unlocking and USB Debugging in Developers Options.
Turn off your phone and remove sim/sdcard.
launch cmd inside the mtkclient folder or cd into it.
backup your Preloader by using: py mtk dumppreloader --filename=preloader.bin.
connect your phone turned off while holding the Volume Down + the Assistant buttons to boot into BROM mode. The Preloader backup will run automatically.
After it's complete, disconnect your device's cable. You will need to do this after every step.
Run the command: py mtk e metadata,userdata and connect while holding the button combo. Wait for it to complete.
Disconnect again, then run: py mtk xflash seccfg unlock and reconnect.
If successful, your device's Bootloader is now unlocked!!!
Rooting​
Knowing which active slot you're booting into will change the next steps slightly. If it's _a, then all following commands will have an _a instead of _b .
Before rebooting after unlocking, use the command: py mtk r boot_b,vbmeta_b boot_b.bin,vbmeta_b.bin to backup your boot and vbmeta partitions respectively. (you will find them in the mtkclient folder afterwards!!)
reboot your phone. a warning screen will show up, don't panic!!!. It will ask you to Factory reset the phone upon successfully booting. Do it and reboot.
Setup your phone normally, then install the aforementioned Magisk APK.
Transfer the backed up boot.bin to your phone and patch it manually inside Magisk.
Transfer the Patched boot image back to your mtkclient folder and rename to i.e boot_magisk.bin.
Turn off your device and launch the command: py mtk w boot_b,vbmeta_b boot_magisk.bin,vbmeta.img.empty. Connect the phone.
when done, reboot your phone and launch Magisk. It will ask you to reinstall itself to complete the setup. Ignore the warning.
Go to Settings and switch to the Beta Update Channel, Reinstall Magisk 23.0 beta and Magisk manager again.
If successful, Your phone is now rooted.
​Passing SafetynetAPI​
Turn on Magisk Hide and repack Magisk Manager from Settings.
Install latest Riru core from Manager.
Install this Universal Safetynet fix by kdrag0n.
reboot and enjoy!!
Credits for all of this goes to:
bkerler for his awesome Tool, none of this is possible w/o it.
Topjohnwu for Magisk.
@kdrag0n for his Safetynet fix.
Slim K said:
​Disclaimer​
​Introduction​​
After finding this amazing device (LKM-EMW) for a very cheap price (90 euros new), I made the fatal mistake of updating through OTA to the Latest Android 10 version 00f.
So where is the Problem?? The latest .DZ from the KDZ firmware wasn't extractable through any tool or script I could find anywhere online, Only the Android 9 ROM was working, but Downgrading through LGUP or LG Flash tool was very risky!!!! (due to ARB protection).
Since this phone's Fastboot mode was replaced with LG's own DOWNLOAD mode, using Fastboot commands to flash the Magisk's patched boot image was impossible. QFIL was also not a possibility, Considering it ships with a MTK chipset, and using SP flash tool will require This phone's particular Scatter file and a signed DA from LG to work, leaving me with no other choices for obtaining Root access.
That is, until I found the following tool: mtkclient by bkerler.
Prerequisites​
backup of your DATA. (during and after unlocking the Bootloader, your data partition must be wiped!!!!)​
Preferably a Windows PC (you will need LGUP in case something goes wrong anyways).​
MTK ALL-in-one 1.0.8 drivers and LG's drivers installed.​
mtkclient installed and running (don't ask me how-to, the Github page is pretty self explanatory).​
This Magisk Alpha Build patched for MTK downloaded for installation.
Since this device uses an A/B partitioning system, you need to know which slot is the active one. Using this App, under the System tab, you can find out which one is active. Mine was _b slot.​
and above all.... Patience.​
Unlocking the Bootloader​
(please note, using python [command] didn't work for me for some reason. However, using py [command] worked for me. Use what works!)​
Turn on OEM Unlocking and USB Debugging in Developers Options.
Turn off your phone and remove sim/sdcard.
launch cmd inside the mtkclient folder or cd into it.
backup your Preloader by using: py mtk dumppreloader --filename=preloader.bin.
connect your phone turned off while holding the Volume Down + the Assistant buttons to boot into BROM mode. The Preloader backup will run automatically.
After it's complete, disconnect your device's cable. You will need to do this after every step.
Run the command: py mtk e metadata,userdata and connect while holding the button combo. Wait for it to complete.
Disconnect again, then run: py mtk xflash seccfg unlock and reconnect.
If successful, your device's Bootloader is now unlocked!!!
Rooting​
Knowing which active slot you're booting into will change the next steps slightly. If it's _a, then all following commands will have an _a instead of _b .
Before rebooting after unlocking, use the command: py mtk r boot_b,vbmeta_b boot_b.bin,vbmeta_b.bin to backup your boot and vbmeta partitions respectively. (you will find them in the mtkclient folder afterwards!!)
reboot your phone. a warning screen will show up, don't panic!!!. It will ask you to Factory reset the phone upon successfully booting. Do it and reboot.
Setup your phone normally, then install the aforementioned Magisk APK.
Transfer the backed up boot.bin to your phone and patch it manually inside Magisk.
Transfer the Patched boot image back to your mtkclient folder and rename to i.e boot_magisk.bin.
Turn off your device and launch the command: py mtk w boot_b,vbmeta_b boot_magisk.bin,vbmeta.img.empty. Connect the phone.
when done, reboot your phone and launch Magisk. It will ask you to reinstall itself to complete the setup. Ignore the warning.
Go to Settings and switch to the Beta Update Channel, Reinstall Magisk 23.0 beta and Magisk manager again.
Se for bem sucedido, seu telefone está agora enraizado.
​Passing SafetynetAPI​
Turn on Magisk Hide and repack Magisk Manager from Settings.
Instale o núcleo riru mais recente do Manager.
Instale esta correção Universal Safetynet por kdrag0n.
reiniciar e desfrutar!!
Créditos para tudo isso vai para:
bkerler for his awesome Tool, none of this is possible w/o it.
Topjohnwu para Magisk.
@kdrag0n for his Safetynet fix.
Click to expand...
Click to collapse
Slim K said:
​Disclaimer​
​Introduction​​
After finding this amazing device (LKM-EMW) for a very cheap price (90 euros new), I made the fatal mistake of updating through OTA to the Latest Android 10 version 00f.
So where is the Problem?? The latest .DZ from the KDZ firmware wasn't extractable through any tool or script I could find anywhere online, Only the Android 9 ROM was working, but Downgrading through LGUP or LG Flash tool was very risky!!!! (due to ARB protection).
Since this phone's Fastboot mode was replaced with LG's own DOWNLOAD mode, using Fastboot commands to flash the Magisk's patched boot image was impossible. QFIL was also not a possibility, Considering it ships with a MTK chipset, and using SP flash tool will require This phone's particular Scatter file and a signed DA from LG to work, leaving me with no other choices for obtaining Root access.
That is, until I found the following tool: mtkclient by bkerler.
Prerequisites​
backup of your DATA. (during and after unlocking the Bootloader, your data partition must be wiped!!!!)​
Preferably a Windows PC (you will need LGUP in case something goes wrong anyways).​
MTK ALL-in-one 1.0.8 drivers and LG's drivers installed.​
mtkclient installed and running (don't ask me how-to, the Github page is pretty self explanatory).​
This Magisk Alpha Build patched for MTK downloaded for installation.
Since this device uses an A/B partitioning system, you need to know which slot is the active one. Using this App, under the System tab, you can find out which one is active. Mine was _b slot.​
and above all.... Patience.​
Unlocking the Bootloader​
(please note, using python [command] didn't work for me for some reason. However, using py [command] worked for me. Use what works!)​
Turn on OEM Unlocking and USB Debugging in Developers Options.
Turn off your phone and remove sim/sdcard.
launch cmd inside the mtkclient folder or cd into it.
backup your Preloader by using: py mtk dumppreloader --filename=preloader.bin.
connect your phone turned off while holding the Volume Down + the Assistant buttons to boot into BROM mode. The Preloader backup will run automatically.
After it's complete, disconnect your device's cable. You will need to do this after every step.
Run the command: py mtk e metadata,userdata and connect while holding the button combo. Wait for it to complete.
Disconnect again, then run: py mtk xflash seccfg unlock and reconnect.
If successful, your device's Bootloader is now unlocked!!!
Rooting​
Knowing which active slot you're booting into will change the next steps slightly. If it's _a, then all following commands will have an _a instead of _b .
Before rebooting after unlocking, use the command: py mtk r boot_b,vbmeta_b boot_b.bin,vbmeta_b.bin to backup your boot and vbmeta partitions respectively. (you will find them in the mtkclient folder afterwards!!)
reboot your phone. a warning screen will show up, don't panic!!!. It will ask you to Factory reset the phone upon successfully booting. Do it and reboot.
Setup your phone normally, then install the aforementioned Magisk APK.
Transfer the backed up boot.bin to your phone and patch it manually inside Magisk.
Transfer the Patched boot image back to your mtkclient folder and rename to i.e boot_magisk.bin.
Turn off your device and launch the command: py mtk w boot_b,vbmeta_b boot_magisk.bin,vbmeta.img.empty. Connect the phone.
when done, reboot your phone and launch Magisk. It will ask you to reinstall itself to complete the setup. Ignore the warning.
Go to Settings and switch to the Beta Update Channel, Reinstall Magisk 23.0 beta and Magisk manager again.
If successful, Your phone is now rooted.
​Passing SafetynetAPI​
Turn on Magisk Hide and repack Magisk Manager from Settings.
Install latest Riru core from Manager.
Install this Universal Safetynet fix by kdrag0n.
reboot and enjoy!!
Credits for all of this goes to:
bkerler for his awesome Tool, none of this is possible w/o it.
Topjohnwu for Magisk.
@kdrag0n for his Safetynet fix.
Click to expand...
Click to collapse
hello everyone, View attachment 5430177at the beginning the commands to unlock the bootloader, py (comand) = is to write py unlock bootloader?
[email protected] said:
hello everyone, View attachment 5430177at the beginning the commands to unlock the bootloader, py (comand) = is to write py unlock bootloader?
Click to expand...
Click to collapse
I don't understand your question. Can you use a better translator/formulate the question clearly? Also, if such a command existed, why would I write 3 paragraphs and a Guide?
My advice, go to the Github page of the tool and read/learn how the tool works first, then come back here if you're stuck.
Thx for this guide! my backup phone k41s is finally rooted
You are a very smart person. We finally have root for LGk41s (WORKS in K51s too).
Thanks!
Does this work on a provider locked LG K40?
Tem como flashear GSIs?
I was able to root my LG K51 from T-Mobile by following this guide.
I appreciate it!
It's don't work to LG K40S (Android 9 and 10), if you brick your phone u can reset them with:
*Backup command (Depend of which active slot, u use command with a or b):
py mtk w boot_a,vbmeta_a boot_a.bin,vbmeta.img.empty
py mtk w boot_b,vbmeta_b boot_b.bin,vbmeta.img.empty
*LGUP flash utility:
LGUP-FLASH-Utility (Based on LGUP-1.16-Cmd and LGUP-1.17-LGUP_Common.dll)
Hi, I think that this is my first post, today I received a LG G820TM to flash it, I found a LGUP version at LG G7 forum, cmd based (LGUP_Cmd.exe), so I managed to prepare something to work with, using a batch file, this gave me some problem with...
forum.xda-developers.com
try to install a twrp custom recovery, please!
guys,, someone already tried to install a gsi, by, mtkclient?
I tried, installing the avoc, on the partition system_ but the loop, extranho, if ma gsi has all the apps to start, q missing something I'm not seeing?
Mod edit - translated by https://www.deepl.com/translator:
Guys, it is possible to install a gsi in lgk41s, but when you install it asks for a password!
******************************
{Mod edit: Link removed}
alexandre-2717 said:
Mod edit - translated by https://www.deepl.com/translator:
Guys, it is possible to install a gsi in lgk41s, but when you install it asks for a password! If anyone wants to help or know more, has a group on telegram!
******************************
Pessoal, é possivel instalar uma gsi no lgk41s, mas quando instala ela pede uma senha! Se alguem quiser ajudar ou saber mais, tem um grupo no telegram!
{Mod edit: Link removed}
Click to expand...
Click to collapse
@alexandre-2717
1. As courtesy, I've translated your above post. With reference to rule no. 4 of the XDA Forum Rules, please post in English or add at least an English translation to your Portuguese posts. Thanks for your cooperation!
Spoiler: Rule No. 4
4. Use the English language.
We understand that with all the different nationalities, not everyone speaks English well, but please try. If you're really unable to post in English, use an online translator. You're free to include your original message in your own language, below the English translation. (This rule covers your posts, profile entries and signature). You could try :- https://translate.google.com/ or https://www.babelfish.com/ or use one of your choice.
2. I've removed the reference to Telegram from your above post. As an exemption from the last bullet of rule no. 5 of the XDA Forum Rules, we grant only developers the privilege to share references to their social media in their own development threads. These conditions obviously don't apply to your thread or you.
Regards
Oswald Boelcke
Senior Moderator
hello everyone, could someone tell me, if it's possible to delete certain files, with some mtkclient command, like locksettings.db which is in data/system/ please , and would I also like to shoot zip files? flesheei a gsi, and i'm stuck in the enter you password to start android screen, if i format py mtk and data, it's loop,
@Oswald Boelcke
thank you and sorry rss
{Mod edit: Quotation fixed}
Slim K said:
como uma ferramenta funciona primeiro e v
Click to expand...
Click to collapse
Rickpad said:
Thx for this guide! my backup phone k41s is finally rooted
Click to expand...
Click to collapse
Does anyone know if it's possible to do this on android 9, on 10 I can, but on 9 no, I wanted to because on android 9 there's recovery even if it's stock, is this a serto development site? does anyone know what prevents?
Great method, not that hard (Although not easy either)
Be aware that you first press the assistant + volume down button and then connect the USB to your PC, not the other way around. I didn't realize this earlier and almost pulled my hair out trying to understand why the program was freezing and sending errors
Also, the bootloader unlock command is outdated now, it was changed to py mtk da seccfg unlock
Worked on single-sim version (LM-K410HM)
Does it work on LG k52?
BRAIAN058 said:
Does it work on LG k52?
Click to expand...
Click to collapse
It's mediatek CPU, probably works, wouldn't hurt to try
[email protected] said:
hello everyone, could someone tell me, if it's possible to delete certain files, with some mtkclient command, like locksettings.db which is in data/system/ please , and would I also like to shoot zip files? flesheei a gsi, and i'm stuck in the enter you password to start android screen, if i format py mtk and data, it's loop,View attachment 5492953
Click to expand...
Click to collapse
does anyone know how to remove Vbmeta verification via MTKCLIENt?

[Guide] Flashing stock rom for Mediatek devices using spflash tool

In this guide i will explain you how to flash stock ROM using spflash for your Mediatek devices in the simplest way possible
Requirements -
a phone with Mediatek SoC
Stock rom which you may or may not find on your vendor official website ( a quick Google search like : Stock rom download for <device codename/device name> would give you an Idea)
Mkt bypass tool
Spflash tool
A pc with windows or Linux installed (Linux May take some more steps to configure)
Steps
Open MKT bypass (attached below or find it from the internet)
Now click bypass button (if you get drivers not installed error follow this video use the lib usb application attached below)
Now connect your phone in power off state using USB and press power button and volume down and wait for mkt bypass to detect and start Bypassing once it is done remember the com port shown in logs
Now open spflash tool click load scatter file now go to your stock ROM folder and select mt<some number>.txt or .xml scatter (use Android scatter if not present) wait for it to process (see the attached image below)
[Shown with red colour in photo below]Now at the topmost tab go to options->connection-> select UART now select the com port shown in mkt Bypass tool go back to spflash main menu(if you can not find com port listed you can just use USB option instead)
Now un check "preloader" and "tranfs" from the files this is very important or you can brick your phone
Make sure download only option is selected and not format+download
we are ready to flash now just click the green download button and wait for the flashing to finish
Disconnect USB and reboot once the green tick mark appear
If you are still stuck in bootloop make sure to use Mt scatter and not android scatter
If you are still bootlooping go to spflash again untick preloader and super and flash after this go to phone recovery and wipe data, this should fix 99% of the bootloops
RESERVED

Categories

Resources