Need help with bricked VONTAR X3 Amlogic S905X3 4/64GB - Android Stick & Console Computers General

Hi!
I bought Amlogic S905X3 4/64GB 1Gbit Ethernet Android Box (VONTAR X3) and it was DOA. No input from HDMI, only two LEDs are glowing and that’s it.
I tried Amlogic Burning Tool, without success. My PC doesn’t see the device despite using USB male-male cable capable of data transfer. The drivers are installed and everything should be ok.
I tried shorting some ‘pins’ as shown here (source: 4pda):
https://cs5-2.4pda.to/19610657/IMG_20200502_174831.jpg?ac3ab8d6ab3d87cf727a9e13ad8d43a8
But that didn’t work either. Maybe these aren’t the ‘pins’ I am looking for?
Also tried the reset button behind the AV/jack port but nothing happened.
Anyway, I’ve connected the device using UART and here’s my PuTTY log (it doesn't matter if I push the reset button or short the pins or put a bootable microSD inside - it's always the same):
Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2020.10.03 19:16:17 =~=~=~=~=~=~=~=~=~=~=~=
SM1:BL:511f6b:81ca2f;FEAT:A0F83180:20282000;POC:F; RCY:0;EMMC:0;READ:0;0.0;CHK:0;
bl2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0001 - pwm id 0x00
bl2_stage_init 0xc0
bl2_stage_init 0x02
L0:00000000
L1:00000703
L2:00008067
L3:15000020
S1:00000000
B2:20282000
B1:a0f83180
TE: 101694
BL2 Built : 20:29:41, Jun 18 2019. g12a ga659aac - [email protected]
Board ID = 1
Set cpu clk to 24M
Set clk81 to 24M
Use GP1_pll as DSU clk.
DSU clk: 1200 Mhz
CPU clk: 1200 MHz
Set clk81 to 166.6M
eMMC boot @ 0
sw8 s
DDR driver_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:37
board id: 1
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
PIEI prepare done
fastboot data load
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 0
enable_fast_boot
dmc_margin_rx==12 dmc_margin_tx==11 steps
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : Training has run successfully!
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_15 build time: Jun 18 2019 20:29:43
DDR cs0 size: 3928MB
DDR cs1 size: 0MB
DMC_DDR_CTRL: 0000002dDDR size: 3928MB
DATA-W[0x00000000]:0xaaaaaaaa,R:0xaaafaaaa
fail D16 18
DATA-W[0x00000000]:0x55555555,R:0x55515555
fail D18
DATA-W[0x00000000]:0x00000001,R:0x00010001
fail D16
DATA-W[0x00000000]:0x00000002,R:0x00010002
fail D16
DATA-W[0x00000000]:0x00000004,R:0x00010004
fail D16
DATA-W[0x00000000]:0x00000008,R:0x00010008
fail D16
DATA-W[0x00000000]:0x00000010,R:0x00010010
fail D16
DATA-W[0x00000000]:0x00000020,R:0x00010020
fail D16
DATA-W[0x00000000]:0x00000040,R:0x00010040
fail D16
DATA-W[0x00000000]:0x00000080,R:0x00010080
fail D16
DATA-W[0x00000000]:0x00000100,R:0x00010100
fail D16
DATA-W[0x00000000]:0x00000200,R:0x00010200
fail D16
DATA-W[0x00000000]:0x00000400,R:0x00010400
fail D16
DATA-W[0x00000000]:0x00000800,R:0x00010800
fail D16
DATA-W[0x00000000]:0x00001000,R:0x00011000
fail D16
DATA-W[0x00000000]:0x00002000,R:0x00012000
fail D16
DATA-W[0x00000000]:0x00004000,R:0x00014000
fail D16
DATA-W[0x00000000]:0x00008000,R:0x00018000
fail D16
DATA-W[0x00000000]:0x00040000,R:0x00010000
fail D16 18
DATA-W[0x00000000]:0x00080000,R:0x00090000
fail D16
DATA-W[0x00000000]:0x00100000,R:0x00110000
fail D16
DATA-W[0x00000000]:0x00200000,R:0x00210000
fail D16
DATA-W[0x00000000]:0x00400000,R:0x00410000
fail D16
DATA-W[0x00000000]:0x00800000,R:0x00810000
fail D16
DATA-W[0x00000000]:0x01000000,R:0x01010000
fail D16
DATA-W[0x00000000]:0x02000000,R:0x02010000
fail D16
DATA-W[0x00000000]:0x04000000,R:0x04010000
fail D16
DATA-W[0x00000000]:0x08000000,R:0x08010000
fail D16
DATA-W[0x00000000]:0x10000000,R:0x10010000
fail D16
DATA-W[0x00000000]:0x20000000,R:0x20010000
fail D16
DATA-W[0x00000000]:0x40000000,R:0x40010000
fail D16
DATA-W[0x00000000]:0x80000000,R:0x80010000
fail D16
cs0 DataBus test failed
ADDR-W[0x00000004]:0xaaaaaaaa,R:0xaaaeaaaa
cs0 AddrBus test failed
fail address pin cs 0 add 0x 00000004
Cfg max: 5, cur: 1. Board id: 255. Force loop cfg
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 5, cur: 2. Board id: 255. Force loop cfg
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 5, cur: 3. Board id: 255. Force loop cfg
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 5, cur: 4. Board id: 255. Force loop cfg
LPDDR4 probe
ddr clk to 1008MHz
Load ddrfw from eMMC, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : ERROR : Training has failed!
1D training failed
Cfg max: 5, cur: 5. Board id: 255. Force loop cfg
DDR3 probe
ddr clk to 672MHz
Load ddrfw from eMMC, src: 0x0002c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : ERROR : Training has failed!
1D training failed
All ddr config failed...
Reset...
boot times 0
And it loops from there to eternity so I decided to post only one loop.
Here are some PCB photos:
https://imgur.com/a/JH8OAEn
Is it dead like disco or can it be reanimated somehow?
I already got a partial refund so if nothing can be done then it goes to a trash can.
Any help would be greatly appreciated.
P.S. Sorry for the external (non)links but I didn't want to post 10 random replies in 10 random threads to unlock the ability to post proper external links. I'm not a filthy spammer

Try using the Amlogic Burning Tool and connect the usb cable to the 2.0 port of the android tv, not to usb 3.0

Hi loocas21,
I had the same problem here.(only 2 leds on)
How I solve it:
1 - diconnect the power on your device;
2 - press the reset button (and let it pressed)
3 - connect the power
I hope it helps you

Hi,
Any news on this?
I'm looking for the right steps before flash.
Thank you

Related

[Q] Xoom usbserial support help

I have Xoom WiFi+3G Model. I have Unlocked and Rooted the device. I am working on a project whereby I am connecting a slave USB device (not a mass-storage or HID) to the Xoom so I can pppd it through ttyUSBx.
I have a USB OTG cable, so when I plug in the USB device, i get the following in dmesg:
usb 3-1: new full speed USB device using tegra-ehci and address 2
usb 3-1: New USB device found, idVendor=229c, idProduct=0001
usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
and valid Product, Manufacturer, and SerialNumber.
lsusb after plugging it in gives me:
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 002 Device 002: ID 22b8:2a70
Bus 003 Device 001: ID 1d6b:0002
Bus 003 Device 002: ID 229c:0001
and the device is on this list.
However, in /dev/, there are already ttyUSBx entries:
ttyUSB0
ttyUSB1
ttyUSB2
ttyUSB3
ttyUSB4
when I plug in my device, a new device is not added to the list.
I recompiled the kernel (using android-tegra-2.6.36-honeycomb branch) with CONFIG_USB_SERIAL=m, so that I could use modprobe to load it manually. After doing modprobe usbserial vendor=x product=x, i get the following:
module 'usbserial' not found
I check /system/lib/modules/ and usbserial.ko does exist.
also, when the device is plugged in, here is the output of /d/usb/devices:
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 2.06
S: Manufacturer=Linux 2.6.36.3-g2a4197e ehci_hcd
S: Product=Tegra EHCI Host Controller
S: SerialNumber=tegra-ehci.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=229c ProdID=0001 Rev= 1.00
S: Manufacturer=xxxx
S: Product=xxxx
S: SerialNumber=000000001222
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=400mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=02 Prot=ff
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=02 Prot=ff Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=(none)
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 2.06
S: Manufacturer=Linux 2.6.36.3-g2a4197e ehci_hcd
S: Product=Tegra EHCI Host Controller
S: SerialNumber=tegra-ehci.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22b8 ProdID=2a70 Rev= 0.00
S: Manufacturer=Motorola, Incorporated
S: Product=Flash MZ600
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=mdm6600
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=mdm6600
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=mdm6600
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=mdm6600
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=mdm6600
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 2.06
S: Manufacturer=Linux 2.6.36.3-g2a4197e ehci_hcd
S: Product=Tegra EHCI Host Controller
S: SerialNumber=tegra-ehci.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
The "Driver=(none)" is what bothers me and I am having trouble fixing. I want the kernel to automatically load the usbserial driver or be able to use modprobe usbserial.
Can someone please help me ?

xoom wont turn on, frozen black screen

hi, last night i wanted to read something on my xoom before going to bed but i couldnt turn it on and i thought the battery run off, but today, after several hours of charging it, still cant turn it on......i tried the power+volume up, power+volume down, adb but since cant be recognized by the pc it's useless. does anyone have a solution?
it's a wifi+3g europe
rooted
z601 model
thanks!!!!!
I have the same problem. I was playing a game (GLWG) on my Xoom and when I exited the app my Xoom froze. I had about 80% battery life left and I tried both holding down Power and Volume UP and Holding down the power and volume down buttons. Nothing happened. I have scanned the internet for help and because when I plug the device into the computer it is not even recognized I don't even know where to begin. I am not in warranty so I can't just return it.
My Xoom is the WiFi only version
Please Help Thanks...
Being as the Xoom has only been out for about 9 months, you should both still be under the 1 year manufacturer's warranty. Give Motorola a call.
I completely forgot the manufacturer gave me a one year warranty thank you so much!
I have similar problem too. I have not touched my xoom for about a week. I charged it for several hours, and I couldn't turn on my xoom. I tried holding the power-on button for a long time, for repeated short time, with volume up, or, down, or both.
Anyone knows any solution before I go to Motorola store?
I got Xoom wifi+3G Stock ROM unrooted HK version (I think it's Honeycomb 3.1). Haven't even rooted, unlocked, or put any kind of custom room yet.
On December 22 I learned that what my Xoom need was a charge. After trying the Power button, and the various other ways to reboot, restart, or shutdown the device I gave up. After a few days (3) I tried to charge it and boom it started working. I don't know if during the time the Xoom completely drained of battery or what but I just waited and then tried to charge it and turn it on. I hope this helps anyone...
hey guys, i just got it repaired from moto, all good now, though i have to root it again
yappoe said:
I have similar problem too. I have not touched my xoom for about a week. I charged it for several hours, and I couldn't turn on my xoom. I tried holding the power-on button for a long time, for repeated short time, with volume up, or, down, or both.
Anyone knows any solution before I go to Motorola store?
I got Xoom wifi+3G Stock ROM unrooted HK version (I think it's Honeycomb 3.1). Haven't even rooted, unlocked, or put any kind of custom room yet.
Click to expand...
Click to collapse
Nope you're gonna have to send it in. I had the same problem where it just stopped working overnight and wouldn't turn on. The computer would recognize that it was plugged in and the charging light would come whenever I plugged it in since I had the tiamat rom on it. Sent it in and freaked out the entire time I waited cause I thought it could have been water damage. Motorola then sent it back with it fully fixed and the same screen, so i have no idea what the problem was. They sent it back with the stock rom and no root, though.
nooooooooooooooooooooooooooo i got the same problem a few days ago i use the volume + power and was able to turn in on today y was gonna do a wipe cache in recovery and the xoom never turn on not even with the volume + power
i dont wanna lose all my data
Each morning I am forced to Power vol-up to turn my Xoom on. There is something that is causing this.
Does anyone know how I can find the app or process that is causing this.
I am on CM10 nightlies.
Thanks
sstrool said:
Each morning I am forced to Power vol-up to turn my Xoom on. There is something that is causing this.
Does anyone know how I can find the app or process that is causing this.
I am on CM10 nightlies.
Thanks
Click to expand...
Click to collapse
Same problem here.
Can happen several times a day, or sometimes some days later.
Happens for CM10, CM10.1, EOS3 and EOS4.
If happened the Notification LED keeps blinking, but no sound on email received.
ADB Logcat does not work.
Would be awesome if anyone knows why or how to debug.
Hello again,
just pushing this post cause i still got huge problems.
Aprox. every day or second i need to power on the xoom cause it wont wake up from standby.
I currently do not know why and how this happens, it just does.
Is there any way of getting my xoom to write a logfile until it hangs up so that i can check this logfile for reasons?
Any suggestions!?
Greetings
Reseting your Xoom
sstrool said:
Each morning I am forced to Power vol-up to turn my Xoom on. There is something that is causing this.
Does anyone know how I can find the app or process that is causing this.
I am on CM10 nightlies.
Thanks
Click to expand...
Click to collapse
I had the same problem and I have a Xoom 32gb Wifi. I just factory reset. Hope that helps. You would have to reinstall and re root though. That worked for me. I had CM10.
Just had a hangup again.
Read out the last_kmsg file, maybe this could help to find some issues:
Code:
...REMOVED FIRST 1000000 LINES...
[74515.067690] mmc0: 32 bytes transferred: 0
[74515.067789] mmc0: starting CMD53 arg 21000100 flags 000001b5
[74515.067839] mmc0: blksz 256 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.067948] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.068011] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
[74515.068094] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.068136] mmc0: 256 bytes transferred: 0
[74515.068249] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.068299] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.068409] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.068490] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.068531] mmc0: 32 bytes transferred: 0
[74515.068682] mmc0: starting CMD52 arg 92001c00 flags 00000195
[74515.068756] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.068823] mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
[74515.069022] mmc0: starting CMD52 arg 92001c10 flags 00000195
[74515.069101] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.069174] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.069273] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.069341] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.069407] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.069485] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.069547] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.069611] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.077394] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.077464] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.077514] mmc0: req done (CMD52): 0: 000010d0 00000000 00000000 00000000
[74515.077601] mmc0: starting CMD53 arg a5000040 flags 000001b5
[74515.077637] mmc0: blksz 64 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.077735] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.077789] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.077819] mmc0: 64 bytes transferred: 0
[74515.077918] mmc0: starting CMD53 arg 15204004 flags 000001b5
[74515.077956] mmc0: blksz 4 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.078039] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.078103] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.078132] mmc0: 4 bytes transferred: 0
[74515.078196] mmc0: starting CMD53 arg 95204004 flags 000001b5
[74515.078231] mmc0: blksz 4 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.078313] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.078366] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.078396] mmc0: 4 bytes transferred: 0
[74515.078463] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.078500] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.078576] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.078635] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.078664] mmc0: 32 bytes transferred: 0
[74515.078735] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.078770] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.078848] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.078905] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.078934] mmc0: 32 bytes transferred: 0
[74515.079015] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.079050] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.079127] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.079186] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.079216] mmc0: 32 bytes transferred: 0
[74515.079605] mmc0: starting CMD53 arg a50000a0 flags 000001b5
[74515.079643] mmc0: blksz 160 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.079733] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.079778] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
[74515.079828] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.079857] mmc0: 160 bytes transferred: 0
[74515.086492] mmc0: starting CMD52 arg 92001c00 flags 00000195
[74515.086561] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.086612] mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
[74515.365555] mmc0: starting CMD52 arg 92001c10 flags 00000195
[74515.365765] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.365846] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.365969] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.366178] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.366258] mmc0: req done (CMD52): 0: 000010d0 00000000 00000000 00000000
[74515.366405] mmc0: starting CMD53 arg 15204004 flags 000001b5
[74515.366469] mmc0: blksz 4 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.366786] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.366885] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.366929] mmc0: 4 bytes transferred: 0
[74515.367037] mmc0: starting CMD53 arg 95204004 flags 000001b5
[74515.367089] mmc0: blksz 4 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.367328] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.367413] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.367457] mmc0: 4 bytes transferred: 0
[74515.367575] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.367628] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.367869] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.367965] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.368008] mmc0: 32 bytes transferred: 0
[74515.368127] mmc0: starting CMD53 arg 210000a0 flags 000001b5
[74515.368180] mmc0: blksz 160 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.368422] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.368519] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.368564] mmc0: 160 bytes transferred: 0
[74515.368767] mmc0: starting CMD52 arg 92001c00 flags 00000195
[74515.368970] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.369049] mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
[74515.369272] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.369326] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.369447] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.369539] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.369582] mmc0: 32 bytes transferred: 0
[74515.370252] mmc0: starting CMD52 arg 92001c10 flags 00000195
[74515.370337] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.370408] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.370521] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.370593] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.370661] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.370744] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.370809] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.370875] mmc0: req done (CMD52): 0: 00001010 00000000 00000000 00000000
[74515.376576] mmc0: starting CMD52 arg 12001c00 flags 00000195
[74515.376645] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.376712] mmc0: req done (CMD52): 0: 000010d0 00000000 00000000 00000000
[74515.376823] mmc0: starting CMD53 arg a50000e0 flags 000001b5
[74515.376873] mmc0: blksz 224 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.376989] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.377044] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
[74515.377111] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.377152] mmc0: 224 bytes transferred: 0
[74515.377296] mmc0: starting CMD53 arg 15204004 flags 000001b5
[74515.377349] mmc0: blksz 4 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.377468] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.377557] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.377601] mmc0: 4 bytes transferred: 0
[74515.377694] mmc0: starting CMD53 arg 95204004 flags 000001b5
[74515.377746] mmc0: blksz 4 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.377860] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.377933] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.377975] mmc0: 4 bytes transferred: 0
[74515.378073] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.378125] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.378233] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.378315] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.378356] mmc0: 32 bytes transferred: 0
[74515.378456] mmc0: starting CMD53 arg 210000c0 flags 000001b5
[74515.378507] mmc0: blksz 192 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.378616] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.378678] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
[74515.378758] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.378800] mmc0: 192 bytes transferred: 0
[74515.378920] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.378970] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.379080] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.379162] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.379204] mmc0: 32 bytes transferred: 0
[74515.379411] mmc0: starting CMD53 arg a5000140 flags 000001b5
[74515.379463] mmc0: blksz 320 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.379586] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.379649] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
[74515.379758] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.379801] mmc0: 320 bytes transferred: 0
[74515.379947] mmc0: starting CMD53 arg 15204004 flags 000001b5
[74515.379996] mmc0: blksz 4 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.380111] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.380202] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.380244] mmc0: 4 bytes transferred: 0
[74515.380334] mmc0: starting CMD53 arg 95204004 flags 000001b5
[74515.380385] mmc0: blksz 4 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.380497] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.380570] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.380612] mmc0: 4 bytes transferred: 0
[74515.380709] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.380758] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.380864] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.380947] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.380989] mmc0: 32 bytes transferred: 0
[74515.381087] mmc0: starting CMD53 arg 21000100 flags 000001b5
[74515.381135] mmc0: blksz 256 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.381243] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.381307] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000002
[74515.381388] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.381430] mmc0: 256 bytes transferred: 0
[74515.381544] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.381594] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.381702] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.381783] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.381824] mmc0: 32 bytes transferred: 0
[74515.382023] mmc0: starting CMD53 arg a5000040 flags 000001b5
[74515.382072] mmc0: blksz 64 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.382186] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.382257] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.382298] mmc0: 64 bytes transferred: 0
[74515.382516] mmc0: starting CMD53 arg 15204004 flags 000001b5
[74515.382566] mmc0: blksz 4 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.382678] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.382767] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.382810] mmc0: 4 bytes transferred: 0
[74515.382899] mmc0: starting CMD53 arg 95204004 flags 000001b5
[74515.382950] mmc0: blksz 4 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.383062] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.383136] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.383177] mmc0: 4 bytes transferred: 0
[74515.383273] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.383322] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.383429] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.383511] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.383553] mmc0: 32 bytes transferred: 0
[74515.383650] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.383699] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.383807] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.383888] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.383928] mmc0: 32 bytes transferred: 0
[74515.384042] mmc0: starting CMD53 arg 21000020 flags 000001b5
[74515.384091] mmc0: blksz 32 blocks 1 flags 00000200 tsac 1000 ms nsac 0
[74515.384199] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.384281] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.384321] mmc0: 32 bytes transferred: 0
[74515.384782] mmc0: starting CMD53 arg a50000a0 flags 000001b5
[74515.384835] mmc0: blksz 160 blocks 1 flags 00000100 tsac 1000 ms nsac 0
[74515.384957] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000003
[74515.385028] mmc0: req done (CMD53): 0: 00001000 00000000 00000000 00000000
[74515.385068] mmc0: 160 bytes transferred: 0
[74515.387363] mmc0: starting CMD52 arg 92001c00 flags 00000195
[74515.387418] sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
[74515.387468] mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
[76426.516983] whisper_notify: accy=USB
[76426.517527] cpcap-otg cpcap-otg: SUSPEND --> PERIPHERAL
[76426.634376] android_work: did not send uevent (0 0 (null))
[76426.780672] android_work: sent uevent USB_STATE=CONNECTED
[76426.836898] android_usb gadget: high speed config #1: android
[76426.837307] android_work: sent uevent USB_STATE=CONFIGURED
[76507.369255] Hard reset buttons pushed
The only thing i see is that it stops at 74515.387468 and than has a break until i tried to logcat it at 76426.516983
got it fixed
Hi all.
I got the same problem a day ago - black screen, and xoom did not want to turn on.
I think i got the solution - battery have to be disconnected and connected again.
I disassembled xoom using one of many manuals posted in internet, unplug battery and plug it back, and my xoom starts as usual now
Hope it may help some of you. It takes 10 min, and small screw drivers set (i used only two of them actually)
regards
sstrool said:
Each morning I am forced to Power vol-up to turn my Xoom on. There is something that is causing this.
Does anyone know how I can find the app or process that is causing this.
I am on CM10 nightlies.
Thanks
Click to expand...
Click to collapse
Elementa/x kernel was cousing these in my xoom and with brocked power button was a pain in a **** switched to eso - no more issues!
Same issue please help!
Hey there!!!
Even my xoom has the same issue!
Please help me , my pc makes a sound when i connect my xoom , that makes it clear that its not bricked!!!
Please reply! How can i fix this by myself?
i'm out of warranty!!!
samsung_saad said:
Hey there!!!
Even my xoom has the same issue!
Please help me , my pc makes a sound when i connect my xoom , that makes it clear that its not bricked!!!
Please reply! How can i fix this by myself?
i'm out of warranty!!!
Click to expand...
Click to collapse
BUMP, i have got exactly the same issue! The volume up technique does not work. I already had a team eos custom rom installed on it. My pc rocognises the xoom when plugged into the computer but that's it no life.
airrunner said:
BUMP, i have got exactly the same issue! The volume up technique does not work. I already had a team eos custom rom installed on it. My pc rocognises the xoom when plugged into the computer but that's it no life.
Click to expand...
Click to collapse
did you try pluging it to your tv via hdmi cable?
I have this BLACK SCREEN but on When connected via HDMI
SO after figuring out my black screen is something to do with the screen, I have figured this out by connecting to HDMI and the xoom opens up on my tv. I took it apart and made sure the LCD plug is still tight, even unlocked and relocked it back in. I made sure everything else is tight, but only thing I could tell was loose was the other side of the wires connected under the motherboard wasnt attached or taped down, Any suggestions on what could be loose, because I can use the touch screen on the black screen to unlock the tab when its on the tv and i can motion white its still black. Please let me know as this is my kids tab. thanks

Using heimdall to flash kernel Not working

I know there few post regarding heimdall, but this post is particular to samsung GT-I9210 (EU ) LTE usage.
Flashing kernel image using heimdall version v1.3.1 failed with below results but the same binary works for SAMSUNG GT-I9100.
Code:
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Manufacturer: "Sasmsung"
Product: "MSM8x60"
Serial No: "?"
length: 18
device class: 2
S/N: 0
VID:PID: 04E8:685D
bcdDevice: 0100
iMan:iProd:iSer: 1:2:0
nb confs: 1
interface[0].altsetting[0]: num endpoints = 1
Class.SubClass.Protocol: 02.02.01
endpoint[0].address: 82
max packet size: 0010
polling interval: 09
interface[1].altsetting[0]: num endpoints = 2
Class.SubClass.Protocol: 0A.00.00
endpoint[0].address: 81
max packet size: 0200
polling interval: 00
endpoint[1].address: 01
max packet size: 0200
polling interval: 00
Claiming interface...
Setting up interface...
Checking if protocol is initialised...
Protocol is not initialised.
Initialising protocol...
ERROR: Failed to initialise protocol!
any help would be highly appreciated.
TIA
Bram

[Q] How to reduce ROM size ??

I am porting paranoid android 3.0 for pico
after all porting work the unpacked rom size is 269 MB
i somewhere raid that unpacked rom size should be less that 235 MB
so what can i do to reduce the size ??
The1sameer said:
I am porting paranoid android 3.0 for pico
after all porting work the unpacked rom size is 269 MB
i somewhere raid that unpacked rom size should be less that 235 MB
so what can i do to reduce the size ??
Click to expand...
Click to collapse
Okay. Do these.
- Delete audio files from /system/Media
- Delete live wallpapers in /system/app like " NoiseField.apk , Galaxy.apk "
- Delete unused apks from /system/app like Email.apk,Quicksearchbox.apk,
- If the symlinks error still persist just delete some more apks and install the ROM. After that you can add apks
Hit thanks if this worked
Also, you can add a memory increasing script by default, and make some changes to ROM to install some of apks in the /data partition
Sent from my HTC Explorer A310e using xda app-developers app
Annoying Bee said:
Okay. Do these.
- Delete audio files from /system/Media
- Delete live wallpapers in /system/app like " NoiseField.apk , Galaxy.apk "
- Delete unused apks from /system/app like Email.apk,Quicksearchbox.apk,
- If the symlinks error still persist just delete some more apks and install the ROM. After that you can add apks
Hit thanks if this worked
Click to expand...
Click to collapse
i am getting following log on compiling the rom on sdk emulator
Code:
C:\Program Files (x86)\Android\android-sdk\tools>emulator -show-kernel -avd pac3
C:\Program Files (x86)\Android\android-sdk\tools>WARNING: Data partition already
in use. Changes will not persist!
WARNING: SD Card image already in use: C:\Users\Sameer\.android\avd\pac3.avd/sdc
ard.img
WARNING: Cache partition already in use. Changes will not persist!
serial0 console
Uncompressing Linux.............................................................
.......................................... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.29-gea477bb ([email protected]) (gcc version
4.6.x-google 20120106 (prerelease) (GCC) ) #1 Wed Sep 26 11:04:45 PDT 2012
CPU: ARMv7 Processor [410fc080] revision 0 (ARMv7), cr=10c5387f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: Goldfish
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
Kernel command line: qemu.gles=0 qemu=1 console=ttyS0 android.qemud=ttyS1 androi
d.checkjni=1 ndns=2
Unknown boot option `qemu.gles=0': ignoring
Unknown boot option `android.qemud=ttyS1': ignoring
Unknown boot option `android.checkjni=1': ignoring
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 515584KB available (2900K code, 707K data, 124K init)
Calibrating delay loop... 117.96 BogoMIPS (lpj=589824)
Mount-cache hash table entries: 512
Initializing cgroup subsys debug
Initializing cgroup subsys cpuacct
Initializing cgroup subsys freezer
CPU: Testing write buffer coherency: ok
net_namespace: 936 bytes
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 176K
goldfish_new_pdev goldfish_interrupt_controller at ff000000 irq -1
goldfish_new_pdev goldfish_device_bus at ff001000 irq 1
goldfish_new_pdev goldfish_timer at ff003000 irq 3
goldfish_new_pdev goldfish_rtc at ff010000 irq 10
goldfish_new_pdev goldfish_tty at ff002000 irq 4
goldfish_new_pdev goldfish_tty at ff011000 irq 11
goldfish_new_pdev goldfish_tty at ff012000 irq 12
goldfish_new_pdev smc91x at ff013000 irq 13
goldfish_new_pdev goldfish_fb at ff014000 irq 14
goldfish_new_pdev goldfish_audio at ff004000 irq 15
goldfish_new_pdev goldfish_memlog at ff006000 irq -1
goldfish_new_pdev goldfish-battery at ff015000 irq 16
goldfish_new_pdev goldfish_events at ff016000 irq 17
goldfish_new_pdev goldfish_nand at ff017000 irq -1
goldfish_new_pdev qemu_pipe at ff018000 irq 18
goldfish_new_pdev goldfish-switch at ff01a000 irq 19
goldfish_new_pdev goldfish-switch at ff01b000 irq 20
goldfish_pdev_worker registered goldfish_interrupt_controller
goldfish_pdev_worker registered goldfish_device_bus
goldfish_pdev_worker registered goldfish_timer
goldfish_pdev_worker registered goldfish_rtc
goldfish_pdev_worker registered goldfish_tty
goldfish_pdev_worker registered goldfish_tty
goldfish_pdev_worker registered goldfish_tty
goldfish_pdev_worker registered smc91x
goldfish_pdev_worker registered goldfish_fb
goldfish_pdev_worker registered goldfish_audio
goldfish_pdev_worker registered goldfish_memlog
goldfish_pdev_worker registered goldfish-battery
goldfish_pdev_worker registered goldfish_events
goldfish_pdev_worker registered goldfish_nand
goldfish_pdev_worker registered qemu_pipe
goldfish_pdev_worker registered goldfish-switch
goldfish_pdev_worker registered goldfish-switch
ashmem: initialized
Installing knfsd (copyright (C) 1996 [email protected]).
yaffs Sep 26 2012 11:04:43 Installing.
msgmni has been set to 1007
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
allocating frame buffer 320 * 480, got ffa00000
console [ttyS0] enabled
brd: module loaded
loop: module loaded
nbd: registered device at major 43
goldfish_audio_probe
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>
eth0 (smc91x): not using net_device_ops yet
eth0: SMC91C11xFD (rev 1) at e080c000 IRQ 13 [nowait]
eth0: Ethernet addr: 52:54:00:12:34:56
goldfish nand dev0: size c200000, page 2048, extra 64, erase 131072
goldfish nand dev1: size 12300000, page 2048, extra 64, erase 131072
goldfish nand dev2: size 4000000, page 2048, extra 64, erase 131072
mice: PS/2 mouse device common for all mice
*** events probe ***
events_probe() addr=0xe0814000 irq=17
events_probe() keymap=qwerty2
input: qwerty2 as /devices/virtual/input/input0
goldfish_rtc goldfish_rtc: rtc core: registered goldfish_rtc as rtc0
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: [email protected]
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
NF_TPROXY: Transparent proxy support initialized, version 4.1.0
NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
xt_time: kernel timezone is -0000
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <[email protected]>
All bugs added by David S. Miller <[email protected]>
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 0
goldfish_rtc goldfish_rtc: setting system clock to 2013-04-22 17:49:50 UTC (1366
652990)
Freeing init memory: 124K
init: cannot open '/initlogo.rle'
yaffs: dev is 32505856 name is "mtdblock0"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.0, "mtdblock0"
yaffs: dev is 32505857 name is "mtdblock1"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.1, "mtdblock1"
yaffs_read_super: isCheckpointed 0
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs_read_super: isCheckpointed 0
init: cannot find '/system/bin/servicemanager', disabling 'servicemanager'
init: cannot find '/system/bin/vold', disabling 'vold'
init: cannot find '/system/bin/qemu-props', disabling 'qemu-props'
init: cannot find '/system/bin/netd', disabling 'netd'
init: cannot find '/system/bin/debuggerd', disabling 'debuggerd'
init: cannot find '/system/bin/rild', disabling 'ril-daemon'
init: cannot find '/system/bin/surfaceflinger', disabling 'surfaceflinger'
init: cannot find '/system/bin/app_process', disabling 'zygote'
init: cannot find '/system/bin/drmserver', disabling 'drm'
init: cannot find '/system/bin/mediaserver', disabling 'media'
init: cannot find '/system/bin/installd', disabling 'installd'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/keystore', disabling 'keystore'
init: cannot find '/system/bin/qemud', disabling 'qemud'
init: cannot find '/system/bin/logcat', disabling 'goldfish-logcat'
init: cannot find '/system/etc/init.goldfish.sh', disabling 'goldfish-setup'
init: cannot find '/system/bin/sh', disabling 'console'
thewisenerd said:
Also, you can add a memory increasing script by default, and make some changes to ROM to install some of apks in the /data partition
Sent from my HTC Explorer A310e using xda app-developers app
Click to expand...
Click to collapse
Which Script, How to Add and where to add these scripts,,, Describe in details...

[DUMP][ROM][PONO] Player Firmware Update FILE 1.0.3 (Gingerbread) (Complete Rom)

Just pulled from my pono player which is based on android (API Level 10)
For people rocking linux and want to update theyre Pono to the latest Firmware 1.0.3 put this file on your ponoplayer drive in .pono/
MIND THE LEADING DOT.
Reboot you're player afterwards and updating should start
DISCLAIMER:
im not responsible for bricks, i just pulled this file as is from my pono.
There wasnt any modification done.
https://file-cloud.eu/public.php?service=files&t=8a42782613be966425cbb4e65290788a
Maybe someone can have a look at it and find out how to enable adb in this rom?
Some additional Device info:
partition table:
Code:
major minor #blocks name
31 0 512 mtdblock0
31 1 1920 mtdblock1
31 2 128 mtdblock2
31 3 4096 mtdblock3
31 4 517632 mtdblock4
179 0 61063168 mmcblk0
179 1 128 mmcblk0p1
179 2 512 mmcblk0p2
179 3 128 mmcblk0p3
179 4 8192 mmcblk0p4
179 5 8192 mmcblk0p5
179 6 262144 mmcblk0p6
179 7 262144 mmcblk0p7
179 8 131072 mmcblk0p8
179 9 131072 mmcblk0p9
179 10 60259072 mmcblk0p10
179 16 62367744 mmcblk1
179 17 62351360 mmcblk1p1
DMESG:
Code:
<5>Linux version 2.6.37 ([email protected]) (gcc version 4.4.3 (GCC) ) #1 Wed Nov 5 16:36:29 PST 2014
<4>CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7f
<4>CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
<4>Machine: OMAP3 Beagle Board
<6>Reserving 8388608 bytes SDRAM for VRAM
<4>Memory policy: ECC disabled, Data cache writeback
<6>OMAP3630 ES1.2 (l2cache sgx neon isp 192mhz_clk )
<6>SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
<7>On node 0 totalpages: 63488
<7>free_area_init_node: node 0, pgdat c05e19e4, node_mem_map c06ad000
<7> Normal zone: 512 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 62976 pages, LIFO batch:15
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62976
<5>Kernel command line: console=ttyO2,115200n8 androidboot.console=ttyO2 mem=256M init=/init ip=off omap_vout.vid1_static_vrfb_alloc=y vram=8M omapfb.vram=0:8M
<6>PID hash table entries: 1024 (order: 0, 4096 bytes)
<6>Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Memory: 248MB = 248MB total
<5>Memory: 243884k/243884k available, 18260k reserved, 0K highmem
<5>Virtual kernel memory layout:
<5> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
<5> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
<5> DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
<5> vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
<5> lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
<5> modules : 0xbf000000 - 0xc0000000 ( 16 MB)
<5> .init : 0xc0008000 - 0xc003c000 ( 208 kB)
<5> .text : 0xc003c000 - 0xc059e000 (5512 kB)
<5> .data : 0xc059e000 - 0xc05e6e80 ( 292 kB)
<6>NR_IRQS:409
<6>Clocking rate (Crystal/Core/MPU): 26.0/400/600 MHz
<6>Reprogramming SDRC clock to 400000000 Hz
<3>dpll3_m2_clk rate change failed: -22
<6>IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts
<6>Total of 96 interrupts on 1 active controller
<6>GPMC revision 5.0
<4>Trying to install interrupt handler for IRQ402
<4>Trying to install interrupt handler for IRQ403
<4>Trying to install interrupt handler for IRQ404
<4>Trying to install interrupt handler for IRQ405
<4>Trying to install interrupt handler for IRQ406
<4>Trying to install interrupt handler for IRQ407
<4>Trying to install interrupt handler for IRQ408
<3>Trying to install type control for IRQ409
<3>Trying to set irq flags for IRQ409
<6>OMAP clockevent source: GPTIMER12 at 32768 Hz
<4>Console: colour dummy device 80x30
<6>Calibrating delay loop... 503.12 BogoMIPS (lpj=1966080)
<6>pid_max: default: 32768 minimum: 301
<6>Security Framework initialized
<4>Mount-cache hash table entries: 512
<6>CPU: Testing write buffer coherency: ok
<6>regulator: core version 0.5
<6>regulator: dummy:
<6>NET: Registered protocol family 16
<6>OMAP GPIO hardware version 2.5
<6>OMAP GPIO hardware version 2.5
<6>OMAP GPIO hardware version 2.5
<6>OMAP GPIO hardware version 2.5
<6>OMAP GPIO hardware version 2.5
<6>OMAP GPIO hardware version 2.5
<6>omap_mux_init: Add partition: #1: core, flags: 0
<6>OMAP3 Pono Rev: A
<6>Found NAND on CS0
<6>Registering NAND on CS0
<3>Unable to get DVI reset GPIO
<6>hw-breakpoint: debug architecture 0x4 unsupported.
<6>OMAP DMA hardware revision 5.0
<4>bio: create slab <bio-0> at 0
<6>regulator: vdd_tp: 3300 mV normal
<6>regulator: EMMC_3V3: 3300 mV normal
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz
<6>twl4030: PIH (irq 7) chaining IRQs 368..375
<6>twl4030: power (irq 373) chaining IRQs 376..383
<6>twl4030: gpio (irq 368) chaining IRQs 384..401
<6>regulator: VUSB1V5: 1500 mV normal standby
<6>regulator: VUSB1V8: 1800 mV normal standby
<6>regulator: VUSB3V1: 3100 mV normal standby
<6>twl4030_usb twl4030_usb: Initialized TWL4030 USB module
<6>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
<6>regulator: VDAC: 1800 mV normal standby
<6>regulator: VAUX2_4030: 2500 mV normal standby
<6>regulator: VDVI: 1800 mV normal standby
<6>regulator: VAUX3: 1800 mV normal standby
<6>regulator: VAUX4: 1800 mV normal standby
<4>omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517
<6>omap_i2c omap_i2c.2: bus 2 rev4.0 at 100 kHz
<6>omap_i2c omap_i2c.3: bus 3 rev4.0 at 400 kHz
<6>Advanced Linux Sound Architecture Driver Version 1.0.23.
<6>Switching to clocksource 32k_counter
<6>musb-hdrc: version 6.0, otg (peripheral+host), debug=0
<6>musb-hdrc musb-hdrc.0: dma type: dma-inventra
<7>musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
<7>musb-hdrc: MHDRC RTL version 1.800
<7>musb-hdrc: setup fifo_mode 4
<7>musb-hdrc: 28/31 max ep, 16384/16384 memory
<6>musb-hdrc musb-hdrc.0: USB OTG mode controller at fa0ab000 using DMA, IRQ 92
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>TCP established hash table entries: 8192 (order: 4, 65536 bytes)
<6>TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
<6>TCP: Hash tables configured (established 8192 bind 8192)
<6>TCP reno registered
<6>UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>NET: Registered protocol family 1
<6>Trying to unpack rootfs image as initramfs...
<6>Freeing initrd memory: 940K
<4>NetWinder Floating Point Emulator V0.97 (double precision)
<4>omap_init_opp_table: no hwmod or odev for iva, [6] cannot add OPPs.
<6>omap-iommu omap-iommu.0: isp registered
<6>ashmem: initialized
<5>VFS: Disk quotas dquot_6.5.2
<4>Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
<6>JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
<7>yaffs: yaffs built Nov 5 2014 16:36:02 Installing.
<6>msgmni has been set to 478
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>OMAP DSS rev 2.0
<6>OMAP DISPC rev 3.0
<7>tm024hbz79 spi3.0: tm024hbz79_spi_probe
<7>panel-tm024hbz79 display0: tm024_panel_probe
<7>tm024hbz79 spi3.0: LCD panel not enabled by bootloader (status 0x610000)
<7>tm024hbz79 spi3.0: MIPI display ID: 000000
<6>tm024hbz79 spi3.0: omapfb: tm024hbz79 rev 00 LCD detected
<3>get_hw_cabc_mode: enter...
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<6>Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
<6>omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
<6>omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
<6>omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
<6>console [ttyO2] enabled
<6>omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3
<6>brd: module loaded
<6>loop: module loaded
<3>mtdoops: mtd device (mtddev=name/number) must be supplied
<6>omap2-nand driver initializing
<6>NAND device: Manufacturer ID: 0x2c, Chip ID: 0xbc (Micron )
<6>NAND BCH ECC SW Init complete
<5>Creating 5 MTD partitions on "omap2-nand.0":
<5>0x000000000000-0x000000080000 : "X-Loader"
<5>0x000000080000-0x000000260000 : "U-Boot"
<5>0x000000260000-0x000000280000 : "U-Boot Env"
<5>0x000000280000-0x000000680000 : "Kernel"
<5>0x000000680000-0x000020000000 : "File System"
<6>OneNAND driver initializing
<6>usbcore: registered new interface driver asix
<6>usbcore: registered new interface driver cdc_ether
<6>usbcore: registered new interface driver smsc95xx
<6>usbcore: registered new interface driver net1080
<6>usbcore: registered new interface driver cdc_subset
<6>usbcore: registered new interface driver zaurus
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>android init
<6>android_probe pdata: c05aeb0c
<6>android_bind
<7>android_bind_config
<6>android_usb gadget: android_usb ready
<6>musb-hdrc musb-hdrc.0: MUSB HDRC host driver
<6>musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: MUSB HDRC host driver
<6>usb usb1: Manufacturer: Linux 2.6.37 musb-hcd
<6>usb usb1: SerialNumber: musb-hdrc.0
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
<6>f_adb init
<6>android_register_function adb
<6>f_mass_storage init
<6>fsg_probe pdev: c05ae910, pdata: c05aebd4
<6>android_register_function usb_mass_storage
<6>android_usb gadget: Mass Storage Function, version: 2009/09/11
<6>android_usb gadget: Number of LUNs=2
<6> lun0: LUN: removable file: (no medium)
<6> lun1: LUN: removable file: (no medium)
<6>mice: PS/2 mouse device common for all mice
<6>input: gpio-keys as /devices/platform/gpio-keys/input/input0
<6>ft5x06_init() - FT I2C Touchscreen Driver (Built Nov 5 2014 @ 16:36:01)
<7>ft5x06_reset_panel_via_gpio() - Toggling GPIO 42 to reset the Touch Panel...
<6>android_usb gadget: high speed config #1: android
<4>omap_device: omap_i2c.2: new worst case activate latency 0: 30517
<6>ft5x06_probe() - FT5x06 found on I2C bus.
<6>input: ft5x06-i2c as /devices/platform/omap/omap_i2c.2/i2c-2/2-0038/input/input1
<6>ft5x06_initialize() - sysfs_create_group() succeeded.
<6>Bosch Sensortec Device detected!
<6>bma220 registered I2C driver!
<6>input: acc as /devices/virtual/input/input2
<6>using rtc device, twl_rtc, for alarms
<6>twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
<6>i2c /dev entries driver
<6>Linux media interface: v0.10
<6>Linux video capture interface: v2.00
<6>max17040 2-0036: MAX17040 Fuel-Gauge Ver 02
<3>bq24073-chgr bq24073-chgr: Initialized
<7>bq24073-chgr bq24073-chgr: bq24392_charger_work: 0
<6>OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
<3>twl4030_wdt twl4030_wdt: Failed to register misc device
<4>twl4030_wdt: probe of twl4030_wdt failed with error -16
<6>device-mapper: uevent: version 1.0.3
<6>device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: [email protected]
<6>cpuidle: using governor ladder
<6>cpuidle: using governor menu
<7>Registered led device: pono::light
<6>omap_pwm_led omap_pwm_led: OMAP PWM LED (pono::lcd) at GP timer 11/0
<7>Registered led device: pono::lcd
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<6>logger: created 64K log 'log_main'
<6>logger: created 256K log 'log_events'
<6>logger: created 64K log 'log_radio'
<6>logger: created 64K log 'log_system'
<6>exFAT: FS Version 1.2.4
<6>exFAT: Core Version 1.2.4
<6>usbcore: registered new interface driver snd-usb-audio
<6>OMAP3 Pono SoC init
<6>ALSA device list:
<6> No soundcards found.
<6>oprofile: hardware counters not available
<6>oprofile: using timer interrupt.
<6>TCP cubic registered
<6>Initializing XFRM netlink socket
<6>NET: Registered protocol family 17
<6>NET: Registered protocol family 15
<5>Registering the dns_resolver key type
<6>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
<6>ThumbEE CPU extension supported.
<3>Power Management for TI OMAP3.
<6>smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized
<6>smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized
<6>SmartReflex Class3 initialized
<6>clock: disabling unused clocks to save power
<6>mmc0: new high speed MMC card at address 0001
<6>mmcblk0: mmc0:0001 CWBC3R 58.2 GiB
<4>Alternate GPT is invalid, using primary GPT.
<6> mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10
<7>panel-tm024hbz79 display0: tm024_panel_enable
<7>panel-tm024hbz79 display0: tm024_panel_power_on
<4>omapdss DPI: Could not find exact pixel clock. Requested 6200 kHz, got 6171 kHz
<7>tm024hbz79 spi3.0: panel_setup
<3>set_sleep_mode: enter...
<4>mmc1: host does not support reading read-only switch. assuming write-enable.
<3>set_display_state: enter...
<6>mmc1: new high speed SDHC card at address e624
<6>mmcblk1: mmc1:e624 SL64G 59.4 GiB
<6> mmcblk1: p1
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<4>regulator_init_complete: incomplete constraints, leaving VAUX3 on
<4>regulator_init_complete: incomplete constraints, leaving VDAC on
<6>twl_rtc twl_rtc: setting system clock to 2000-01-11 17:18:42 UTC (947611122)
<7>panel-tm024hbz79 display0: tm024_panel_enable
<7>panel-tm024hbz79 display0: tm024_panel_power_on
<7>panel-tm024hbz79 display0: tm024_panel_enable
<7>panel-tm024hbz79 display0: tm024_panel_power_on
<6>omap_vout omap_vout: Buffer Size = 3686400
<6>omap_vout omap_vout: : registered and initialized video device 0
<6>omap_vout omap_vout: Buffer Size = 3686400
<6>omap_vout omap_vout: : registered and initialized video device 1
<6>Freeing init memory: 208K
<6>EXT4-fs (mmcblk0p7): recovery complete
<6>EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
<6>EXT4-fs (mmcblk0p9): recovery complete
<6>EXT4-fs (mmcblk0p9): mounted filesystem with ordered data mode. Opts: (null)
<4>EXT4-fs (mmcblk0p8): warning: maximal mount count reached, running e2fsck is recommended
<6>EXT4-fs (mmcblk0p8): recovery complete
<6>EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
<4>init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
<4>omap_device: smartreflex.1: new worst case activate latency 0: 30517
<7>ft5x06_tpreset_show() - Resetting Touch Panel
<7>ft5x06_reset_panel_via_gpio() - Toggling GPIO 42 to reset the Touch Panel...
<6>asoc: ponoaudio-hifi <-> omap-mcbsp-dai.1 mapping ok
<3>init: cannot find '/system/bin/sgx/rc.pvr', disabling 'pvr'
<4>omap_device: smartreflex.0: new worst case deactivate latency 0: 30517
<4>omap_device: omap_i2c.3: new worst case activate latency 0: 61035
<4>omap_device: omap_uart.3: new worst case deactivate latency 0: 30517
<4>omap_device: omap_uart.3: new worst case activate latency 0: 30517
<6>warning: `zygote' uses 32-bit capabilities (legacy support in use)
<6>request_suspend_state: wakeup (3->0) at 11983917243 (2000-01-11 17:18:51.062377931 UTC)
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<4>omap_device: omap_uart.2: new worst case activate latency 0: 457763
<4>[EXFAT] trying to mount...
<4>[EXFAT] mounted successfully
<4>omap_device: omap_uart.2: new worst case activate latency 0: 915527
<4>omap_device: omap_uart.2: new worst case activate latency 0: 4455566
<4>omap_device: omap_uart.2: new worst case activate latency 0: 4547119
<4>omap_device: omap_uart.2: new worst case activate latency 0: 4791259
<4>omap_device: omap_uart.2: new worst case activate latency 0: 4821777
<4>omap_device: omap_uart.3: new worst case activate latency 0: 6225585
<4>omap_device: omap_uart.2: new worst case activate latency 0: 6988525
<4>omap_device: omap_i2c.2: new worst case deactivate latency 0: 91552
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<4>omap_device: omap_uart.2: new worst case activate latency 0: 7354736
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<6>EXT4-fs (mmcblk0p7): re-mounted. Opts: (null)
<6>EXT4-fs (mmcblk0p7): re-mounted. Opts: (null)
<4>omap_device: omap_uart.2: new worst case activate latency 0: 8178710
<4>omap_device: omap_uart.2: new worst case activate latency 0: 10253906
<4>[EXFAT] trying to unmount...
<4>[EXFAT] unmounted successfully
<6>binder: 1310:1311 transaction failed 29189, size 84-0
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=0
<6>request_suspend_state: sleep (0->3) at 170425236611 (2000-01-11 17:21:29.503666784 UTC)
<6>ft5x06_suspend() - Driver is suspending.
<6>request_suspend_state: wakeup (3->0) at 267929729460 (2000-01-11 17:23:07.008190148 UTC)
<6>ft5x06_resume() - Driver is resuming.
<7>ft5x06_reset_panel_via_gpio() - Toggling GPIO 42 to reset the Touch Panel...
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<7>tm024hbz79 spi3.0: tm024hbz79_bl_update_status: level=255
<4>omap_device: omap_uart.2: new worst case activate latency 0: 11932373
<4>omap_device: omap_uart.2: new worst case activate latency 0: 13793945
<3>init: untracked pid 1691 exited
<4>omap_device: omap_uart.2: new worst case activate latency 0: 279388427
<4>[EXFAT] trying to mount...
<4>[EXFAT] mounted successfully
Mounted FileSystems:
Code:
rootfs / rootfs ro,relatime 0 0
tmpfs /dev tmpfs rw,relatime,mode=755 0 0
devpts /dev/pts devpts rw,relatime,mode=600 0 0
proc /proc proc rw,relatime 0 0
sysfs /sys sysfs rw,relatime 0 0
tmpfs /mnt/asec tmpfs rw,relatime,mode=755,gid=1000 0 0
/dev/block/platform/mmci-omap-hs.1/by-name/system /system ext4 ro,relatime,barrier=1,data=ordered 0 0
/dev/block/platform/mmci-omap-hs.1/by-name/userdata /data ext4 rw,relatime,barrier=1,data=ordered 0 0
/dev/block/platform/mmci-omap-hs.1/by-name/cache /cache ext4 rw,relatime,barrier=1,data=ordered 0 0
debugfs /sys/kernel/debug debugfs rw,relatime 0 0
/dev/block/vold/179:10 /mnt/internal vfat rw,dirsync,nosuid,nodev,noexec,relatime,uid=1000,gid=1015,fmask=0702,dmask=0702,allow_utime=0020,codepage=cp437,iocharset=iso8859-1,shortname=mixed,utf8,errors=remount-ro 0 0
/dev/block/vold/179:10 /mnt/secure/asec vfat rw,dirsync,nosuid,nodev,noexec,relatime,uid=1000,gid=1015,fmask=0702,dmask=0702,allow_utime=0020,codepage=cp437,iocharset=iso8859-1,shortname=mixed,utf8,errors=remount-ro 0 0
tmpfs /mnt/internal/.android_secure tmpfs ro,relatime,size=0k,mode=000 0 0
/dev/block/vold/179:17 /mnt/sdcard exfat rw,dirsync,nosuid,nodev,noexec,relatime,uid=1000,gid=1015,fmask=0702,dmask=0702,allow_utime=0020,codepage=cp437,iocharset=utf8,namecase=0,errors=remount-ro 0 0
/dev/block/vold/179:17 /mnt/secure/asec exfat rw,dirsync,nosuid,nodev,noexec,relatime,uid=1000,gid=1015,fmask=0702,dmask=0702,allow_utime=0020,codepage=cp437,iocharset=utf8,namecase=0,errors=remount-ro 0 0
tmpfs /mnt/sdcard/.android_secure tmpfs ro,relatime,size=0k,mode=000 0 0
build.prop:
Code:
# begin build properties
# autogenerated by buildinfo.sh
ro.build.id=GRJ22
ro.build.display.id=pono-eng 1.0.3 GRJ22 eng.daveg.20141105.164641 test-keys
ro.build.version.incremental=eng.daveg.20141105.164641
ro.build.version.sdk=10
ro.build.version.codename=REL
ro.build.version.release=1.0.3
ro.build.date=Wed Nov 5 16:46:58 PST 2014
ro.build.date.utc=1415234818
ro.build.type=eng
ro.build.user=daveg
ro.build.host=ubuntu
ro.build.tags=test-keys
ro.product.model=NY001
ro.product.brand=PonoMusic
ro.product.name=pono
ro.product.device=pono
ro.product.board=pono
ro.product.cpu.abi=armeabi-v7a
ro.product.cpu.abi2=armeabi
ro.product.manufacturer=unknown
ro.product.locale.language=mdpi
ro.product.locale.region=
ro.wifi.channels=
ro.board.platform=omap3
# ro.build.product is obsolete; use ro.product.device
ro.build.product=pono
# Do not try to parse ro.build.description or .fingerprint
ro.build.description=pono-eng 1.0.3 GRJ22 eng.daveg.20141105.164641 test-keys
ro.build.fingerprint=PonoMusic/pono/pono:1.0.3/GRJ22/eng.daveg.20141105.164641:eng/test-keys
# end build properties
#
# ADDITIONAL_BUILD_PROPERTIES
#
ro.config.notification_sound=OnTheHunt.ogg
ro.config.alarm_alert=Alarm_Classic.ogg
dalvik.vm.heapsize=24m
ro.kernel.android.checkjni=1
ro.setupwizard.mode=OPTIONAL
net.bt.name=Android
dalvik.vm.stack-trace-file=/data/anr/traces.txt
persist.service.adb.enable=1
persist.service.debuggable=1
init.svc.adbd=running
persist.sys.usb.config=mass_storage,adb
recovery last_log: http://pastebin.com/zqKy119L
LOGCAT: http://pastebin.com/JjD2KjTR
Took a quick look.
/default.prop:
persist.service.adb.enable=1
ro.secure=0
/init.rc:
on property: persist.service.adb.enable=1
start adbd
/sbin/adbd binary present
Also present:
/diags/busybox
/system/xbin/su
/system/app/Term.apk (v1.0.3)
If you can find a way to start this terminal (activity com.android.term/.Term)
perhaps a Diag mode? and then start /system/xbin/su
So everything looks ok for adb. But if it is passed through USB?
You can try adb over Wifi if you know the ip address of your Pono.
EDIT: just learned Pono has no wifi...
Recovery mode? I see /sdcard/package.zip in /system/bin/recovery binary.
/package.zip
Choose a package to install:
update_package
Finding update package...
Opening update package...
Verifying update package...
Package not installed
Good luck.
mhm package.zip is new to me, that would be very helpful if that works, i will try to install a rom using that location instead of internal storage/.pono/anyrom.update
I have a launcher already installed and a customized rom.
I can flash stuff using android test-key signed rom zip's
Why would they have ADB running if there's no way to access it? I have tried what I can to access it over USB, but so far no luck.
I repartitioned my internal SD card and lost access to my player. The player boots fine, but it just shows 0.0 GB of 0.0 GB free and won't prompt me to mount the disks as mass storage when I plug it to my PC, so I can't repartition the storage again. Therefore I need ADB access
tweakradje said:
Took a quick look.
/default.prop:
persist.service.adb.enable=1
ro.secure=0
/init.rc:
on property: persist.service.adb.enable=1
start adbd
/sbin/adbd binary present
Also present:
/diags/busybox
/system/xbin/su
/system/app/Term.apk (v1.0.3)
If you can find a way to start this terminal (activity com.android.term/.Term)
perhaps a Diag mode? and then start /system/xbin/su
So everything looks ok for adb. But if it is passed through USB?
You can try adb over Wifi if you know the ip address of your Pono.
EDIT: just learned Pono has no wifi...
Recovery mode? I see /sdcard/package.zip in /system/bin/recovery binary.
/package.zip
Choose a package to install:
update_package
Finding update package...
Opening update package...
Verifying update package...
Package not installed
Good luck.
Click to expand...
Click to collapse
Maybe this option is missing to get adb to work:
persist.sys.usb.config=mass_storage,adb
nope, tried that option aswell already, adbd on the device is running tough...
i wonder if there is another unpropagated USB connection inside the pono just for debugging stuff...
old firmware file?
does anyone have a copy of a pre 1.0.6 firmware update file. since 1.0.6 the internal storage is mega slow - and have searched high and low to see if i could roll back. thanks in advance.
Hi everyone,
I know this thread is 6 years old, but...
I'm realizing that I'm not using my Pono for years, mostly because of the incomplete UI. I'm more a developer than an Android expert, so I'd like some help in order to get started.
I have basic knowledge of Android (adb, apk, all that wizardry), basic reverse skills and pretty good knowledge of Linux.
So here is my questions to you
- How did Psych0_D0g extract the logcat logs? To me, having logcat means that he did actually make adb work.
- how did he extract the recovery log? I didn't find any was to boot into recovery (pressing volume Up and boot, or volume down, or both..)
Next step for me will be able to generate a firmware update image in order to add/remove what I need..
Thanks for any help!

Categories

Resources