S7 SMG930V Bootloop - Samsung Galaxy S7 Questions and Answers

Hi,
My mom's S7 is in a bootloop of sorts. I have no idea how it happened, but right now when I try to factory reset it from Vol+Up+Power it goes to the splash screen and then to "installing system updates" and after a few seconds stops and turns off.
We don't care about the data, I just want be able to use this device for a trade in. I have downloaded the most recent firmware from Sam Mobile, G930VVRSBCTC1_G930VVZWBCTC1_VZW.
I have downloaded Odin3 v3.13. From here I don't know much, but I tried and succeeded in BL, AP, and CP and odin says success. When it reboots it goes back to updating system and freezes again and shut off. When I try to do CSC it fails.
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 5169 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn
<ID:0/006> lksecapp.mbn
<ID:0/006> xbl.elf
<ID:0/006> tz.mbn
<ID:0/006> hyp.mbn
<ID:0/006> devcfg.mbn
<ID:0/006> pmic.elf
<ID:0/006> rpm.mbn
<ID:0/006> cmnlib.mbn
<ID:0/006> keymaster.mbn
<ID:0/006> apdp.mbn
<ID:0/006> msadp.mbn
<ID:0/006> cmnlib64.mbn
<ID:0/006> sec.dat
<ID:0/006> NON-HLOS.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> persist.img.ext4
<ID:0/006> modem.bin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response from boot-loader
<ID:0/006> adspso.bin
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006> Receive Response from boot-loader
<ID:0/006> cache.img.ext4
<ID:0/006> FAIL! (Write)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
After searching the forum, I am not sure what all of BL, AP, CP, CSC and Userdata does, but under the impression I need to do them for it to reset my phone?
Thanks.

Okay, so I got it to work. I hadn't installed the Samsung drivers. It was successful, but upon turning on I am now getting "Recovery booting..." in the splash screen and then it goes to the "erasing" screen, stops and turns off.
Any thoughts?

Related

My phone froze several times and not opening.

Hello everybody,
I need help.
My phone was froze several times in this week. Later it was frozing in 3-4 minutes.. I was opening it Power Reset button..
Finally, When I reset the phone, It's stopped on SAMSUNG LOGO.
I opened the Recovery menu and wipe data/wipe cache. but It frozen on wipe cache progress .
I tried to load 4.3 rom via ODIN. But I stopped the update.
Again I pressed to reset button and my phone waited on "Firmware upgrade encountered...kies etc..." screen text.
I can't open Recovery Menu, only Download menu.
What can I do ? I tried update 4.3 rom, 4.1.2 rom... Failed...
I'd re-partion via Odin...It's passed.
But I cant update rom, root, or others... :S
I need helpppp...
This is Odin output.
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> tz.img
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
MoostaphaKaya said:
Hello everybody,
I need help.
My phone was froze several times in this week. Later it was frozing in 3-4 minutes.. I was opening it Power Reset button..
Finally, When I reset the phone, It's stopped on SAMSUNG LOGO.
I opened the Recovery menu and wipe data/wipe cache. but It frozen on wipe cache progress .
I tried to load 4.3 rom via ODIN. But I stopped the update.
Again I pressed to reset button and my phone waited on "Firmware upgrade encountered...kies etc..." screen text.
I can't open Recovery Menu, only Download menu.
What can I do ? I tried update 4.3 rom, 4.1.2 rom... Failed...
I'd re-partion via Odin...It's passed.
But I cant update rom, root, or others... :S
I need helpppp...
This is Odin output.
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> tz.img
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Anybody is there?
MoostaphaKaya said:
Anybody is there?
Click to expand...
Click to collapse
did you flash a rom not intended for your device? if you did, based on what I've seen here on the forums that's very bad.
you might have to odin back to stock
http://forum.xda-developers.com/showthread.php?t=2046439

sm-g800h: odin failed it need {ext4} plies can help me.

I am trying to update to kitkat and keep failing in odin near the end of the process - see messages below. Has anyone else seen this and how can I overcome the problem?
Thanks
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> sbl1.mbn
<ID:0/006> rpm.mbn
<ID:0/006> tz.mbn
<ID:0/006> sdi.mbn
<ID:0/006> NON-HLOS.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Ext4)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
mahadyisaac said:
I am trying to update to kitkat and keep failing in odin near the end of the process - see messages below. Has anyone else seen this and how can I overcome the problem?
Thanks
Added!!
Odin v.3 engine (ID:6)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
SingleDownload.
aboot.mbn
NAND Write Start!!
sbl1.mbn
rpm.mbn
tz.mbn
sdi.mbn
NON-HLOS.bin
boot.img
recovery.img
system.img.ext4
FAIL! (Ext4)
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Have you tried different Odin versions or different firmwares?Where did you find the firmware file?
v7

Odin problem with s7 edge (sm-g935f)

Hello, when I start the process in odin with the correct firmware of my mobile phone it shows this message of fail
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 4090 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
I have no idea why it happens i have actually a lineage os 15.1 installed and twrp installed. help me please

[Solved]Samsung Galaxy S7 - Odin Complete(Write) Operation Failed after system.img

Hey,
I hope there is someone who can help me. I know there are several other Threads about this Topic but i couldnt find the answer for this.
I just rooted my Samsung Galaxy S7 and after that I deactivated OEM unlock by mistake. Now I want to flash the firmware back to start from scratch.
Firmware from sammobile: SAMSUNG GALAXY S7 SM-G930F XEG GERMANY (1&1) G930FXXS5ESF1 FIRMWARE
ANDROID 8.0.0
But when I try to flash i only reach system.img and right after the error Complete(write) Operation Failed.
Does anybody know what I can do to get this problem fixed.
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> skip file list for home binary
<ID:0/006> param.bin
<ID:0/006> modem_debug.bin
<ID:0/006> Home Binary Download
<ID:0/006> Total Binary size: 4091 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> cm.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks alot
TehMeddin said:
Hey,
I hope there is someone who can help me. I know there are several other Threads about this Topic but i couldnt find the answer for this.
I just rooted my Samsung Galaxy S7 and after that I deactivated OEM unlock by mistake. Now I want to flash the firmware back to start from scratch.
Firmware from sammobile: SAMSUNG GALAXY S7 SM-G930F XEG GERMANY (1&1) G930FXXS5ESF1 FIRMWARE
ANDROID 8.0.0
But when I try to flash i only reach system.img and right after the error Complete(write) Operation Failed.
Does anybody know what I can do to get this problem fixed.
<ID:0/006> Added!!
<ID:0/006> Odin engine v(ID:3.1301)..
<ID:0/006> File analysis..
<ID:0/006> skip file list for home binary
<ID:0/006> param.bin
<ID:0/006> modem_debug.bin
<ID:0/006> Home Binary Download
<ID:0/006> Total Binary size: 4091 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> cm.bin
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Thanks alot
Click to expand...
Click to collapse
Flash Germany unbranded DBT.
Is FRP lock on?
cooltt said:
Flash Germany unbranded DBT.
Is FRP lock on?
Click to expand...
Click to collapse
well just ignore my post.... my laptop seems to be over his best years.
changed laptop and it worked.
but thanks for your help.
is there a way to close the thread?
TehMeddin said:
well just ignore my post.... my laptop seems to be over his best years.
changed laptop and it worked.
but thanks for your help.
is there a way to close the thread?
Click to expand...
Click to collapse
Edit the post title to" Solved"

Stuck in Download mode

Dear friends!
I myself use and flash a Xiaomi device, easy peazy. a friend of mine kinda softbricked her S10e Exynos and asked me for help, so I try to fix her issue but I am not succeeding. So I am not the most expierenced with Samsung devices.
She flashed a Lineage rom and corresponding TWRP, OEM is unlocked. Now Download mode opens automatically after bootloader warning. So I thought Odin or heimdall should be a piece of cake. But Odin always ends with failed write process and when I flash a recovery with heimdall I cannot reach recovery mode, it is always D/L mode. Cable is fine, tried every USB port on two Notebooks
Original Firmware is downloaded by SamFirm.
Can anyone give me advise how to go on??
Thanks
Code:
<ID:0/006> Odin engine v(ID:3.1401)..
<ID:0/006> File analysis..
<ID:0/006> Total Binary size: 8538 M
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NAND Write Start!!
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> param.bin
<ID:0/006> up_param.bin
<ID:0/006> cm.bin
<ID:0/006> keystorage.bin
<ID:0/006> uh.bin
<ID:0/006> vbmeta.img
<ID:0/006> boot.img
<ID:0/006> __XmitData_Write
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!

Categories

Resources