Related
Hey Friends,
You must have seen very good days with Lenovo P2 but when there comes a bad day when your phone stops responding to button holds and restarts. You may or may not have a clue what to do to get your phone working again just like before.
I got into this situation where only thing my phone was able to operate was a RED LED on connecting it to my laptop. Then I had to read tens of pages on XDA to find answers to all my questions. If you are in such a situation and your phone is UNLOCKED then you have come to the right place. Procedure is quite simple but remember, I am writing this guide to define complete process from blackout to complete update so follow this guide as per your needs.
I faced this situation of Total Blackout / Dead Phone (Almost) with only Red LED working and it can be very scary. So, here is the simplest procedure you can follow. I want to appreciate all those people who helped me in finding a way to boot my phone with each and everything working. Long story short, let's get this done.
Tools Required:
I am mentioning here all the Tools you will need. I will urge you to download and save these tools in case you want to unbrick your phone any time:
1. Minimal ADB and Fastboot setup for PC
2. Lenovo USB drivers v1.1.33
3. Qualcomm USB Drivers
4. Qualcomm Flash Image Loader (QFIL) v2.0.1.9 for your PC in case you have corrupted your phone's IMEI and/ or Baseband
5. Blankflash.bat in case you want to recover from total blackout (Attached)
6. Stock MM S048 Firmware for Lenovo P2 in case phone doesn't boot
7. S048_ModemTelephony.zip in case your phone boots through Stock MM S048 but SIM isn't detected and IMEI is missing. I have made a complete modem zip file for installation through recovery.
8. S251_ModemTelephony.zip in case your phone is on latest firmware and doesn't detect SIM and has lost IMEI. I have made a complete modem zip file for installation through recovery.
9. QCN file for recovering baseband version and giving you most precious network signals. (Attached)
10. WinRAR or PeaZip for uncompressing files
I will recommend you to have a specific folder for keeping all these tools in a single place.
Procedure for Unbricking:
Before going with the procedure, make sure you have downloaded all the files you need, updated Lenovo and Qualcomm drivers etc. Here is the procedure:
1. If total blackout with red LED notification when connecting to PC: Unzip blankflash.zip to a folder in C drive. Now connect your P2 to PC through USB, press volume+, volume- and power button simultaneously and double click blankflash.bat. You might have no success in your first try. Just keep trying and it will load your phone to Fastboot. Restart your phone in TWRP if installed and install a working ROM for your phone after doing a wipe. If all is good and phone works OK then great but if you have lost IMEI and baseband then it is better to reinstate your phone through first MM stock ROM S048
2. Install S048 firmware through Minimal ADB and Fastboot - use flash instructions in .txt file.
3. Wait for startup of phone. Check if fingerprint, BT, WIFI and SIM work if all work then OK.
4. If fingerprint, BT, WIFI and SIM are not working then check IMEI through dialer. Dial *#06#. If IMEI is not available then install latest TWRP through Fastboot.
5. Start P2 in TWRP recovery and install S048_ModemTelephony.zip. Restart phone to see if WIFI and SIM work.
6. If SIM is detected but not giving signals and Baseband is shown as unknown then extract 000000_0.qcn file given in .7z and restore through QFIL and restart your phone into Fastboot.
7. Now, install stock recovery of S048 firmware through Fastboot and restart your phone.
8. Use your phone like you normally do and update your P2 till firmware S251 and see if everything works including calls. Update your phone through OTA.
9. After OTA installation, stock recovery may say that update failed. Just press Back, go into Wipe user data menu and Wipe Cache only. Restart your phone which will be updated to latest version and will ask you to update to a newer version. Allow it to download the next update.
10. After installation of S251 update, install latest TWRP through Fastboot and install most recent version of LOS 16 so that your vendor partition is stable and free from any bloated files. Now, use your phone just like you want to.
If you need further clarification then ask in this thread.
Bro my phone is not unlocked can i try thz one
Ranji007 said:
Bro my phone is not unlocked can i try thz one
Click to expand...
Click to collapse
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
alirazaagha said:
You should download S048 and use flashall.bat inside that archive to install it all. However, if you lose IMEI or baseband then you can use modem and qcn files given in this thread.
Click to expand...
Click to collapse
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Ranji007 said:
Bro now i wanna use ...minimal adb ..my phone is totally bricked only red light glowing
Click to expand...
Click to collapse
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Bro how to connect my phone to blank flash...can u PLZZ help
hackiee said:
don't worry just flash blank flash from the link given in the op, you will get the bootloader back
Click to expand...
Click to collapse
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Ranji007 said:
Laptop is not detecting my device bro i installed all lenovo and Qualcomm drivers...any idea
Click to expand...
Click to collapse
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
alirazaagha said:
If red light blinks, your phone can be detected by your laptop. Check ports in device manager settings and you'll see a new port with Qualcomm 9800 series number. If that's there, try blankflash to start in fastboot. It might need some tries before startup. Be patient and keep trying till you are in fastboot.
Click to expand...
Click to collapse
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Ranji007 said:
Bro ..thanks for reply....in my phone red blink is glowing continuously ..but after connecting there is no change...can u say which buttons i want to press?
Click to expand...
Click to collapse
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
alirazaagha said:
Press Volume+, Volume- and Power simultaneously and double click flashblank.bat. It might take some tries to finally install the scripts and start phone in fastboot. It took me 20+ tries to finally detect my phone through blankflash. Please, read OP completely.
Click to expand...
Click to collapse
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Ranji007 said:
Bro we want to connect each time removing usb cable and connect again like that ..we wanna do 20 times??
Click to expand...
Click to collapse
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
alirazaagha said:
No. Keep USB connected. Try blankflash. If it doesn't detect phone or go ahead. Close command terminal, double click again and keep doing it till it processes the files. If it is stuck somewhere. Close terminal and try again.
Click to expand...
Click to collapse
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Ranji007 said:
Bro is there any solution ..i continuously pressed volume and power buttons connected to laptop and opening blank flash continuously for number of times ...but there was no reaction...only waiting for device is showing ? on my pc ...
Click to expand...
Click to collapse
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
alirazaagha said:
Check if your USB cable is alright and appropriate drivers are installed. Otherwise reinstall drivers, restart your PC and try again.
Click to expand...
Click to collapse
Bro we want to change any settings in device manager ...?
Ranji007 said:
Bro we want to change any settings in device manager ...?
Click to expand...
Click to collapse
No. Just update drivers.
alirazaagha said:
No. Just update drivers.
Click to expand...
Click to collapse
Bro when u take to service center they said for u motherboard problem or something??
Ranji007 said:
Bro when u take to service center they said for u motherboard problem or something??
Click to expand...
Click to collapse
Fortunately, I never took it there.
alirazaagha said:
Fortunately, I never took it there.
Click to expand...
Click to collapse
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ?..iam trying thiz method
Ranji007 said:
My phone was fallen in water then i changed the display..few days after it stopped working ..and when i take to serive centre they said to change motherboard..but it's the 80% of phone price...so iam here ..iam trying thiz method
Click to expand...
Click to collapse
I think you might have damaged some hardware. But anyway if you want to use blankflash, I have a method.
In lenovo p2 we have another mode called QDloader mode, in which we can use blankflash. For entering into this mode, it's little tricky but, can enter in one or two go.
So, here's how:
1. Switch off the mobile.
2. Press the volume up key,
3. While holding the volume up key, insert the usb cable and at the same time press the power button (this is the trick, we have to insert and hit at the same time).
And voila! :highfive: you will see black screen with only red notification led blinking.
we are into QDloader mode. Now use blankflash :good:
Sorry for lack of details, but I'm not sure it will help anyway. Feeling pretty bad right now.
T-Mobile Oneplus 7 Pro. 256GB version.
I wanted to go to stock OxygenOS after buying the branded version two weeks ago.
I successfully got T-Mobile to unlock my SIM, and got OnePlus to send me unlock code for my bootloader after a week.
Successfully unlocked via fastboot. Tried several times to flash TWRP and no success using fastboot.
Tried MSM-Downloader from guacamole_21_O.07_190512_repack and successfully held volume both buttons to connect to the PC. MSM-Downloader said it was successfully connected.
I cannot find the exact error message I got from MSM-Downloader, but it said it didn't match plus another error message. At that point, my heart sank.
USB Device Not Recognized keeps popping up on windows again and again, while the connect sound plays. Doesn't matter if I hold down the volume buttons or not.
Can't get into qualcomm EDL mode. My guess is I hosed my boot and now it restarts endlessly when connected to anything at all.
Is this the end of my journey? I did tons of research on the best phone and the best deals available to save money, but looks like I played myself here with lack of caution.
I would suggest following this guide to attempt reflashing of the international firmware (use the androidfilehost download).
If that also fails, you could always just reflash the TMO firmware with this guide.
bmg1001 said:
I would suggest following this guide to attempt reflashing of the international firmware (use the androidfilehost download).
If that also fails, you could always just reflash the TMO firmware with this guide.
Click to expand...
Click to collapse
I cannot get into EDL. Regardless of what buttons I press (I am holding both volume buttons down in excess of 5 seconds) when connecting USB to the phone, Windows makes the "connect" sound endlessly and the driver isn't recognized.
If I can get into EDL, I will definitely try the above.
Do you have the proper drivers installed to use EDL mode?
Also, if you go into the Device Manager, do you see the phone in there? Should pop up as something like "Qualcomm HS-USB 9008" or some variant of that.
bmg1001 said:
Do you have the proper URL installed to use EDL mode?
Also, if you go into the Device Manager, do you see the phone in there? Should pop up as something like "Qualcomm HS-USB 9008" or some variant of that.
Click to expand...
Click to collapse
Ok. I may be making progress thanks to your help but do have some hurdles I can see.
I do see the device when I hook it up to another computer. It shows up as Unknown USB Device (Device Descriptor Request Failed).
When I go to device manager to manually update the driver, and browse to the location I extracted the CAB file into, I see lots of devices to choose from, but the Qualcomm driver cab file list does not show "Qualcomm HS-USB QDLoader 9008" as an option. I see many Qualcomm USB Composite Devices in the list but none I have chosen seem to work (install fails).
Hmm. I know it may be an obvious question, but just to be sure, you're using the cable that came with the device correct?
bmg1001 said:
Hmm. I know it may be an obvious question, but just to be sure, you're using the cable that came with the device correct?
Click to expand...
Click to collapse
Yes, that is correct. Same cable i used to get into fastboot, etc... The original PC I caused the problems with recognized the device differently (showed up as a Qualcomm device) when I got into EDL with it before.
Edit: First event when plugging it into this second PC under device properties:
Device USB\VID_0000&PID_0002\5&3c8d678&0&2 was not migrated due to partial or ambiguous match.
Last Device Instance Id: USB\VID_0000&PID_0000\5&1AE39384&0&2
Class Guid: {36fc9e60-c465-11cf-8056-444553540000}
Location Path:
Migration Rank: 0xF000FFFFFFFFF000
Present: false
Status: 0xC0000719
I just did some googling and found this article. Perhaps you can try the drivers in this guide? They are .exe files so they should be easy to install, but I'm not sure if the other drivers I provided have any OnePlus specific stuff in it, but it's worth a shot.
bmg1001 said:
I just did some googling and found this article. Perhaps you can try the drivers in this guide? They are .exe files so they should be easy to install, but I'm not sure if the other drivers I provided have any OnePlus specific stuff in it, but it's worth a shot.
Click to expand...
Click to collapse
I've already tried the .zip version with no success. I am loath to install an .exe file (don't want to make the problem worse by infecting my PC) but may as well. I will restart and report back. Thank you again for your attention.
If this doesn't bear fruit, I may be SOL, correct?
unluckyoneplus7pro said:
I've already tried the .zip version with no success. I am loath to install an .exe file (don't want to make the problem worse by infecting my PC) but may as well. I will restart and report back. Thank you again for your attention.
If this doesn't bear fruit, I may be SOL, correct?
Click to expand...
Click to collapse
Mmm. The link I gave seems to have been blocked by XDA when I tried to access it from my post. Never had a problem myself with that site, but who knows.
You should be able to ultimately recover the phone though. Perhaps asking in one of the unbrick threads? OnePlus phones are theoretically unbrickable because we have good access to our EDL mode.
bmg1001 said:
Mmm. The link I gave seems to have been blocked by XDA when I tried to access it from my post. Never had a problem myself with that site, but who knows.
You should be able to ultimately recover the phone though. Perhaps asking in one of the unbrick threads? OnePlus phones are theoretically unbrickable because we have good access to our EDL mode.
Click to expand...
Click to collapse
I'll try there next. Can't seem to get any of my windows machines to recognize the thing.
bmg1001 said:
Mmm. The link I gave seems to have been blocked by XDA when I tried to access it from my post. Never had a problem myself with that site, but who knows.
You should be able to ultimately recover the phone though. Perhaps asking in one of the unbrick threads? OnePlus phones are theoretically unbrickable because we have good access to our EDL mode.
Click to expand...
Click to collapse
OK! I found on reddit that if you hold your vol up + down + power for 30 seconds, it will boot back into fastboot, which it did! Holy **** I'm so happy. Haven't even seen if the PC recognizes it but will check now. If it does, I just need to not screw up the conversion to international.
Thank you for your "unbrickable" comment. That gave me hope to not give up.
unluckyoneplus7pro said:
OK! I found on reddit that if you hold your vol up + down + power for 30 seconds, it will boot back into fastboot, which it did! Holy **** I'm so happy. Haven't even seen if the PC recognizes it but will check now. If it does, I just need to not screw up the conversion to international.
Thank you for your "unbrickable" comment. That gave me hope to not give up.
Click to expand...
Click to collapse
I just wanted to share a tip. After you load the msmtool and before you connect your phone with the cable, click the start button, the message will read "waiting for device". Then, as soon as you plug in the cable while holding the p-up and p-down, the msmtool will automatically start. No more rushing to hit the start button before EDL mode times out.
razorshiv said:
I just wanted to share a tip. After you load the msmtool and before you connect your phone with the cable, click the start button, the message will read "waiting for device". Then, as soon as you plug in the cable while holding the p-up and p-down, the msmtool will automatically start. No more rushing to hit the start button before EDL mode times out.
Click to expand...
Click to collapse
That's pretty cool. Makes the whole process much less stressful.
Got it up and running with international version. Now to see if I can get LOS installed. My sincere thanks to all and apologies for crapping up the board with my panic. I thought I had really screwed up, but it appears it was just stuck in EDL mode and needed a hard (HARD) reset.
Hey man, thanks for the donation. Glad you were able to get your phone up and running!
Holy Sh*t man. I know 5 bucks ain't much but I wanted to thank you so much. I thought I was fukd
Hey guys. I need some help. this is my wrong doing !!
I got a network unlocked T mobile which I started using with AT&T. Today I received the unlock code from T mobile to unlock bootloader which I did. then I I installed TWRP and Magisk without any issues. then I tried to fix the persis.img coz fingerpritn is not working. it didnt work so I left it alone. But I dont know why I wiped cache, data and then phone got stuck at boot loop. (no backup). I tried to install using MSM tool but it didnt work. MSM tool was not detecting the phone. then in TWRP I clicked on EDL and now the phone screen is blank. tried every possible combination of keys but no luck. was doing all this on windows 10. any help would be greatly appreciated. thanks
kool_am said:
Hey guys. I need some help. this is my wrong doing !!
I got a network unlocked T mobile which I started using with AT&T. Today I received the unlock code from T mobile to unlock bootloader which I did. then I I installed TWRP and Magisk without any issues. then I tried to fix the persis.img coz fingerpritn is not working. it didnt work so I left it alone. But I dont know why I wiped cache, data and then phone got stuck at boot loop. (no backup). I tried to install using MSM tool but it didnt work. MSM tool was not detecting the phone. then in TWRP I clicked on EDL and now the phone screen is blank. tried every possible combination of keys but no luck. was doing all this on windows 10. any help would be greatly appreciated. thanks
Click to expand...
Click to collapse
So it turns out its not a hard brick. I'm stuck on TWRP. I'm able to get to fastboot. I tried to install Oxygen OS thru fastboot but the PC is not detecting the phone in fastboot. Mac detects it but I believe all the stock Roms are for PC use. I did try it on my MAc and was able to open a terminal window inside the Oxygen OS folder but then the fastboot device command is not found. any help would be greatly appreciated. I installed SDK and ADB drivers on PC but in device manager the device still only shows as Android device with no drivers. !! thanks
kool_am said:
So it turns out its not a hard brick. I'm stuck on TWRP. I'm able to get to fastboot. I tried to install Oxygen OS thru fastboot but the PC is not detecting the phone in fastboot. Mac detects it but I believe all the stock Roms are for PC use. I did try it on my MAc and was able to open a terminal window inside the Oxygen OS folder but then the fastboot device command is not found. any help would be greatly appreciated. I installed SDK and ADB drivers on PC but in device manager the device still only shows as Android device with no drivers. !! thanks
Click to expand...
Click to collapse
Solved !
solved how? i greatly would like to know how to flash from fastboot, i know that isnt what this thread was about but im having the exact same problems you are with msm. i can see the phone in fastboot but i have no idea how to flash or what to flash from there. I can get into recovery but i cant copy anything over to the phone and the drivers dont show up for adb. so i pretty much ONLY have fastboot and dont know what to do! 2 days since the phone been down and im lost AF
JCroffut said:
solved how? i greatly would like to know how to flash from fastboot, i know that isnt what this thread was about but im having the exact same problems you are with msm. i can see the phone in fastboot but i have no idea how to flash or what to flash from there. I can get into recovery but i cant copy anything over to the phone and the drivers dont show up for adb. so i pretty much ONLY have fastboot and dont know what to do! 2 days since the phone been down and im lost AF
Click to expand...
Click to collapse
Can msm detect the phone when connected in fastboot. Also check device manager in pc to make sure it detects the phone as qualcomm device. Otherwise msm will not work.
Download msm. Turn phone off. Connect phone to pc. Open msm. Press start. Press volume down and power button on phone. It should be detected by msm and should start flashing the software.
Standby....
When plugged in the phone in EDL it shows
QUSB_BULK_CID0412 with an exclamation mark inside a yellow triangle
When i plugged in the phone and open fastboot it shows
Android with an exclamation point inside a yellow triangle
I booted up msm, clicked other, clicked start, pressed volume down and volume up and plugged it in. still says waiting for device to connect. ive also tried this with a number of keys being help, ive tried to boot from twrp straight into edl mode, none of which works
which all says to me its a driver issue of some kind, but for 3 days ive been slaving away on xda and cannot for the life of me figure out where to get the drivers.
JCroffut said:
Standby....
When plugged in the phone in EDL it shows
QUSB_BULK_CID0412 with an exclamation mark inside a yellow triangle
When i plugged in the phone and open fastboot it shows
Android with an exclamation point inside a yellow triangle
I booted up msm, clicked other, clicked start, pressed volume down and volume up and plugged it in. still says waiting for device to connect. ive also tried this with a number of keys being help, ive tried to boot from twrp straight into edl mode, none of which works
which all says to me its a driver issue of some kind, but for 3 days ive been slaving away on xda and cannot for the life of me figure out where to get the drivers.
Click to expand...
Click to collapse
It is a driver issue for sure. When connected device manager should detect as qualcomm hd9008.......
kool_am said:
It is a driver issue for sure. When connected device manager should detect as qualcomm hd9008.......
Click to expand...
Click to collapse
i figured that, i am at a complete loss as to where to find the drivers. i actually might need you to hold my hand on this one a tiny bit because im about to smash the phone on the ground and say someone stole it. thats where i am with this phone haha
JCroffut said:
i figured that, i am at a complete loss as to where to find the drivers. i actually might need you to hold my hand on this one a tiny bit because im about to smash the phone on the ground and say someone stole it. thats where i am with this phone haha
Click to expand...
Click to collapse
qualcomm hs-usb qdloader 9008 - this is the exact name of the driver.
Try this link: https://forum.xda-developers.com/t/guide-fixing-hard-bricks-qualcomm-hs-usb-qdloader-9008.3403868/
kool_am said:
qualcomm hs-usb qdloader 9008 - this is the exact name of the driver.
Try this link: https://forum.xda-developers.com/t/guide-fixing-hard-bricks-qualcomm-hs-usb-qdloader-9008.3403868/
Click to expand...
Click to collapse
standby ill read through it now. we also have 2 different threads going so i can combine them if thats easier for you
kool_am said:
qualcomm hs-usb qdloader 9008 - this is the exact name of the driver.
Try this link: https://forum.xda-developers.com/t/guide-fixing-hard-bricks-qualcomm-hs-usb-qdloader-9008.3403868/
Click to expand...
Click to collapse
Only download the qualcomm driver from this link. Or search for it online.
I have spent much more time than you trying to figure this out. I have a pc and Mac both. Mac is not compatible with a lot of the software and my pc usb ports are all bad. Point being, leave it alone for a day or so. Come back at it with a fresh start and fresh mind.
kool_am said:
Only download the qualcomm driver from this link. Or search for it online.
I have spent much more time than you trying to figure this out. I have a pc and Mac both. Mac is not compatible with a lot of the software and my pc usb ports are all bad. Point being, leave it alone for a day or so. Come back at it with a fresh start and fresh mind.
Click to expand...
Click to collapse
i hear that. after 3 days of non stop working at it im pretty sure im just not smarter than the phone today lol. looks like this phone is now stolen and going into a trash can lol
JCroffut said:
i hear that. after 3 days of non stop working at it im pretty sure im just not smarter than the phone today lol. looks like this phone is now stolen and going into a trash can lol
Click to expand...
Click to collapse
If I were you, I wouldn't throw the phone away. Like I said it's a simple issue of driver. Install the correct driver and make sure you see it as qualcomm device in device manager. Trust me, from then on, it's just a matter of a few clicks.
I unbricked my phone to t mobile and then converted to global rom without any issues.
kool_am said:
If I were you, I wouldn't throw the phone away. Like I said it's a simple issue of driver. Install the correct driver and make sure you see it as qualcomm device in device manager. Trust me, from then on, it's just a matter of a few clicks.
I unbricked my phone to t mobile and then converted to global rom without any issues.
Click to expand...
Click to collapse
i sent you a private convo on here if thats ok so i dont spam the forum! You may be able to help me out if i could borrow a few minutes of your time!
JCroffut said:
i hear that. after 3 days of non stop working at it im pretty sure im just not smarter than the phone today lol. looks like this phone is now stolen and going into a trash can lol
Click to expand...
Click to collapse
i was definatly kidding tho this is my only phone and i have to solve this problem lol
I'm not sure if you have read this thread already. I messed up my phone a couple days ago as well and follow the steps there and was able to MSM my phone back to stock.
[OP8][OOS TMO 55CB] Unbrick tool to restore your device to OxygenOS
Disclaimer: By attempting any of the processes listed in this thread you accept full responsibility for your actions. I will not be held responsible if your device stops working, catches fire, or turns into a hipster and claims to have been...
forum.xda-developers.com
Hello everyone,
History : So i was using Rice driod on my OP 8T peacefully and i got an update on the rom. i installed the update via local update of the rom and after reboot the phone never booted back. i tried all button combos to make to boot anything like fastboot or recovery etc but nothing worked.
Problem : While connecting to PC the device shows as "Qualcomm HS Diagnostic 900E" I know it should show as 'qualcomm hs loader 900' something which indicates EDL state. So i can't perform MSM. There are not port showing in MSM either. Its blank. Even after forcefully trying to boot EDL ( button combos ), it always boots back to same state.
Fixes i have tried : Reinstalled qualcomm drivers many times, also tried many other versions of MSM including the Hydrogen OS one. No solution.
Can anyone please help me with this situation. Its been few days now and i have really no hope left with the device.
alp47470 said:
Hello everyone,
History : So i was using Rice driod on my OP 8T peacefully and i got an update on the rom. i installed the update via local update of the rom and after reboot the phone never booted back. i tried all button combos to make to boot anything like fastboot or recovery etc but nothing worked.
Problem : While connecting to PC the device shows as "Qualcomm HS Diagnostic 900E" I know it should show as 'qualcomm hs loader 900' something which indicates EDL state. So i can't perform MSM. There are not port showing in MSM either. Its blank. Even after forcefully trying to boot EDL ( button combos ), it always boots back to same state.
Fixes i have tried : Reinstalled qualcomm drivers many times, also tried many other versions of MSM including the Hydrogen OS one. No solution.
Can anyone please help me with this situation. Its been few days now and i have really no hope left with the device.
Click to expand...
Click to collapse
complete noob here but I have heard someone said they fixed using indian msm tool, maybe I am wrong, idk
LR7875 said:
complete noob here but I have heard someone said they fixed using indian msm tool, maybe I am wrong, idk
Click to expand...
Click to collapse
I have tried MSM already no fix as it doesn't detect the device in EDL state. Hence no port shows up
alp47470 said:
I have tried MSM already no fix as it doesn't detect the device in EDL state. Hence no port shows up
Click to expand...
Click to collapse
does the computer even detect your device? what name of the device does it show up
alp47470 said:
I have tried MSM already no fix as it doesn't detect the device in EDL state. Hence no port shows up
Click to expand...
Click to collapse
1st, make sure your device is connected and recognized as 9008 HS-USB QDLoader.
2nd, try using MSM of 9R Ported ROM for 8T, it works in almost every situation
LinhBT said:
1st, make sure your device is connected and recognized as 9008 HS-USB QDLoader.
2nd, try using MSM of 9R Ported ROM for 8T, it works in almost every situation
Click to expand...
Click to collapse
The 1st one is main problem. It doesn't recognise as 9008 HS-USB QDLoader, it always keeps showing to 900E mode.
just a long shot, as i am on a 5t not the 8, but has windoze perhaps updated and "fixed" the usb driver on your behalf?
my 5t was invisible after unlocking, until i forced windoze to update the driver to an unsigned (working) version
[EOL][11.0][OFFICIAL] LineageOS 18.1 for Oneplus 5 & 5T
Is there anybody out there!ðŸ¤
forum.xda-developers.com
alp47470 said:
The 1st one is main problem. It doesn't recognise as 9008 HS-USB QDLoader, it always keeps showing to 900E mode.
Click to expand...
Click to collapse
That's a total different device state, it's on Diag mode, not EDL mode. Try to turn off the device COMPLETELY, then either using hardkeys ( VOL + VOL - press and hold at the same time, plug in cable ) or use Deep-Fash cable to put the device into correct EDL 9008 mode.
So, guys i was finally able to fix the device by EDL point method. Somehow the device was able to boot to edl anyhow. The drivers were correct and so was the cable etc, Thank you all for still helping me.
So relieved so my 8T alive again.
alp47470 said:
So, guys i was finally able to fix the device by EDL point method. Somehow the device was able to boot to edl anyhow. The drivers were correct and so was the cable etc, Thank you all for still helping me.
So relieved so my 8T alive again.
Click to expand...
Click to collapse
Could you please be more specific as to how you got it to connect in EDL mode - it would help others who end up in the same situation.
BillGoss said:
Could you please be more specific as to how you got it to connect in EDL mode - it would help others who end up in the same situation.
Click to expand...
Click to collapse
As you know already the phone wasn't able to go to EDL mode no matter what i did. I really don't know what caused the issue and why it wasn't booting even after using button combos (both vol) or to power off manually (vol up and power) it was went to Diagnostic Mode.
Here's what i did :
-Went to local shop for removing the back panel by those heating machines
-Unplug battery
-Then used the EDL points on the motherboard to force the device to boot EDL (this method is more seen in Mi , Redmi phones)
-The device immediately recognised by just one tap on "enum" now.
Thats how i flashed the OS, plugged the battery and panel, reboot
Thanks for sharing that - much appreciated.
alp47470 said:
As you know already the phone wasn't able to go to EDL mode no matter what i did. I really don't know what caused the issue and why it wasn't booting even after using button combos (both vol) or to power off manually (vol up and power) it was went to Diagnostic Mode.
Here's what i did :
-Went to local shop for removing the back panel by those heating machines
-Unplug battery
-Then used the EDL points on the motherboard to force the device to boot EDL (this method is more seen in Mi , Redmi phones)
-The device immediately recognised by just one tap on "enum" now.
Thats how i flashed the OS, plugged the battery and panel.
Click to expand...
Click to collapse
So the localshop is using Testpoint trick. It has the same effect as using Deep-Flash cable but more trustable, only that u will have to open the back cover.
Congrats on successfully rescue the device mate
LinhBT said:
So the localshop is using Testpoint trick. It has the same effect as using Deep-Flash cable but more trustable, only that u will have to open the back cover.
Congrats on successfully rescue the device mate
Click to expand...
Click to collapse
Thanks bro. Actually the shop kepper didn't do anything. Instead he was saying that the battery was damaged or something (probably scamming me) or he actually didn't had any idea for real. I had read about EDL point thing, so i just asked the shopkeeper to just remove the back panel. Rest i came home and did everything lol. NGL it was scary as hell.
In the process i also discovered that 8T and 9R being mostly identical also have same EDL points on motherboard. Same positioning too.
alp47470 said:
Thanks bro. Actually the shop kepper didn't do anything. Instead he was saying that the battery was damaged or something (probably scamming me) or he actually didn't had any idea for real. I had read about EDL point thing, so i just asked the shopkeeper to just remove the back panel. Rest i came home and did everything lol. NGL it was scary as hell.
In the process i also discovered that 8T and 9R being mostly idenical also have same EDL points on motherboard. Same positioning too.
Click to expand...
Click to collapse
Ah I see, same here when I 1st try the Testpoint trick few years back, scary as hell cuz that was the only phone I had at that time ))))
Btw, yes, 9R and 8T shares almost everything besides of SOC's name ( Snap870 in fact is Snap865 OCing ). That's why I told u to use the MSM Tool of 9R port ROM for 8T, it passes almost every errors u may face when using MSM of 8T itself!
alp47470 said:
As you know already the phone wasn't able to go to EDL mode no matter what i did. I really don't know what caused the issue and why it wasn't booting even after using button combos (both vol) or to power off manually (vol up and power) it was went to Diagnostic Mode.
Here's what i did :
-Went to local shop for removing the back panel by those heating machines
-Unplug battery
-Then used the EDL points on the motherboard to force the device to boot EDL (this method is more seen in Mi , Redmi phones)
-The device immediately recognised by just one tap on "enum" now.
Thats how i flashed the OS, plugged the battery and panel, reboot
Click to expand...
Click to collapse
Hi, I'm the same boat after a bad flash of OSS12, hard brick, black screen, not detected in Windows devices manager, no vibration with every button combination ...
Could you share where the edl points are on the OnePlus 8T motherboard please ?
I would be eternally grateful!
NZX-DeSiGN said:
Hi, I'm the same boat after a bad flash of OSS12, hard brick, black screen, not detected in Windows devices manager, no vibration with every button combination ...
Could you share where the edl points are on the OnePlus 8T motherboard please ?
I would be eternally grateful!
Click to expand...
Click to collapse
Here.. hope it helps
Trying to flash my friend's phone back to stock but having some issues, you might have seen twixyfig's post in the OnePlus 9 Pro threads, but it's a regular OP9 and not the Pro.
Anyways, I have been trying to flash to working condition but MSM won't help. It keeps saying "No valid trg ID" and "Param preload" for a while now. This happened because we tried to root the phone but failed. The bootloader is unlocked, and fastboot works too.
TIA.
Whenever you post asking for help, always make sure to add as many details as possible. Your phone model, variant, current firmware, the tool you are using, the tools you used before, the steps you took before you started facing issues, every detail you can possibly tell. Only then someone might be able to help.
shadabkiani said:
Whenever you post asking for help, always make sure to add as many details as possible. Your phone model, variant, current firmware, the tool you are using, the tools you used before, the steps you took before you started facing issues, every detail you can possibly tell. Only then someone might be able to help.
Click to expand...
Click to collapse
So its a oneplus 9 (Chinese model), before it got bricked it was on android 12, we tried MSM V5.1.89 and CMD, cmd said " No boot.img found "
twixyfig said:
So its a oneplus 9 (Chinese model), before it got bricked it was on android 12, we tried MSM V5.1.89 and CMD, cmd said " No boot.img found "
Click to expand...
Click to collapse
Download the MSM Tool (Global) from this link. Global works on Chinese variant (LE2110) too. Have proper drivers OnePlus drivers installed. Turn off your phone and set it aside, do not connect to PC yet. Run the MSM Tool exe file. Once its loaded, click Start and it should wait for device. Now on your phone, hold vol+ and vol- buttons (no power button), and connect the cable to phone. This will make the phone enter EDL mode. The PC would recognize the device (USB plugged in sound) but phone screen would still be black. On MSM, the flashing would start and would be done in about 4-5 mins. Good luck.
shadabkiani said:
Download the MSM Tool (Global) from this link. Global works on Chinese variant (LE2110) too. Have proper drivers OnePlus drivers installed. Turn off your phone and set it aside, do not connect to PC yet. Run the MSM Tool exe file. Once its loaded, click Start and it should wait for device. Now on your phone, hold vol+ and vol- buttons (no power button), and connect the cable to phone. This will make the phone enter EDL mode. The PC would recognize the device (USB plugged in sound) but phone screen would still be black. On MSM, the flashing would start and would be done in about 4-5 mins. Good luck.
Click to expand...
Click to collapse
Thanks! Im gonna try this today and give you an update when something happens
twixyfig said:
Thanks! Im gonna try this today and give you an update when something happens
Click to expand...
Click to collapse
I think you were trying Indian MSM Tool. That might be the problem.
When your open MSM Tool, choose Others as login.
Write me in dm and I will help you, I think I can solve your problem
you can download OP9PRO India MSM tool(OnePlus_9_Pro_India_OxygenOS_11.2.4.4) and
1.unzip OP9Pro India ROM and download to your phone(select the firhose chebox)
2.if you success to download it,your phone will restart to the OOS.
3.Login your Google account and unlock OEM,then reboot your phone
4. install "Oxygen Updater", VERSION 5.7.3，you can find it on github.
5.download OOS for OP9 , archive name is "1797d47ddef0fca1411fb006b9c7a1a7ba33d818.zip"
6.enter the oxygen updater,and flash "1797d47ddef0fca1411fb006b9c7a1a7ba33d818.zip" to your phone
7.reboot and fixed!
PS: my english is so suck,try to read it!
good luck!