Hello dear members,
i installed my device but the touchscreen does not react . First i habe installed everything was good but after a few minutes the system does not work. Display goes on but the Touchscreen does not react. If i use a wireless Mouse is everythin ok. I have in the Factory Settings reset the Mouse and Button Settings but nothing helps.
-Android 8 PX5 last MCU Update
Sorry for my bad english
If it really doesn't work. Return it. I have one that works fine, some times it doesn't register my touch but thats probably do too screen angle and me just misplacing my finger
I bought one unit here in Germany with the same specs and it came like that. Then next the display started failing and the board was overheating. Will send it back monday. You should do the same.
Related
Hi everyone,
Last night my polaris started playing tricks on me. Basically the touch screen is not responsive but the hard buttons all work. For some reason though when I try to do a hard reset (GPS, Internet and reset) it doesn't perform a hardreset. Also I can't put it into boot loader mode
Any suggestions?
Can you try and flash a new ROM?
Yes i've flashed another cooked ROM and till nothing, even D/L official 6.1 ROM and still no touch screen.
I would immediately assume the touch screen is broken but the fact I can't use the hard reset combination (even though the individual buttons work) has got me confused
Hi!
I've the same issue.
This morning everything was fine but, now i can't use the touch screen.
It seems that the "cursors" is always in the upper right corner, but as i move it clicking in the other part of the screen it runs back in that corner.
I'm not able to hard reset, i've tried to do a clearstorage but i'm not able to enter the security code "1234" as i haven't the cotnroll of the screen
Have you solved this problem?
I will let you know shortly but cut a long story short it looks like i broke it
on closer inspection of can see a small dent/scratch on the screen so ordered a new touch screen off ebay. It arrived today so i'll be putting it in shortly so fingers crossed it was actually the problem. I figure the problem was the screen causing a permanent short and hence interupting my attempts at a hard reset
The screen cost about $35 AUD delivered and it took me about 30 minutes to pull the device apart, just have to see how long it takes to get it back together now
I'll post back soon
To me something similar has hapened.
Once i was changing the values of the pressure settings and the screen become unresponsive!
It was quite easy to fix it:
-just press the GPS button and the center button at the same time, then you will enter the menu were you can align the screen and, at the same time, the pressure registry values become as default.
Hope this helps with your problem, good luck with the screen replacement!
It's alive!!!!
Replaced the digitizer (touch screen) and all works again ...
Just to warn you though it isn't for the faint of heart, I thought i'd broke it a couple of times throughout the repair, next time i'll be getting a repair quote first
Congratulations!!
As my polaris is still under warranty i'll send my to the official assistance for the touch screen replacement!
Yesterday i've got my Cruise back from assistanza.. thay have replaced the whole mother board and now the touch screen is working
its a good idea to install my mobiler. this lets you control the device using a pc when the touch screen doesn't work. you can then back up your stuff before sending off for repair.
So I have a problem with my CUBE U30GT-H. I bought it almost 3 months ago, all have worked very well, but now touch screen doesn't.
Problem occurs when I have to unlock screen, it simply doesn't work after sleep. But when I restart it works again, tablet totally works with my mice. I tried to wipe cache and reinstall firmware, but nothing changed. So i think it will be a good option if touch screen doesn't shut down when tablet put to sleep. I was searching for a touch screen config, but didn't find. I hope you can help me with problem and give some ideas.
Now I use this firmware Evolution JB 1.0.2 ( flashmyandroid.com/forum/showthread.php?1192-Release-Evolution-JB-1-0-2-27-08-2012 )
P.S. I am new on this forum so I don't know where to put this question. sorry...
Hi, I get my CHUWI Vi8 dualboot 16.04.2015. Everything was ok, it worked very good but at the next day morning I wanted to use it and I find that touchscreen doesn't work. I left it for few minutes and when I look at it again It was rebooting, as it turned out - with no end. I finally turned it of when I lost hope and turn on again. This time I get info that my device is diagnosed, then that it's repairing, at the and I saw windows 8 repair panel but all in chinese. I wanted to choose one of two buttons but touchscreen still didn't working. Next time I used mouse by OTG and by lucky choosing some options I eld to reset. But it changed nothing. Then I get info from seller to click vol+ and power button for 20 seconds. It brought me system selection screen, I choose android with mouse and it worked normally just without touch. I don't what else I can do to fix it. Have you any ideas?
PS: I know it's a cliche but sorry for my english;]
So, have a bit of a situation and not sure what to do.
My touch screen is working, but only to a point. Only the top status bar and bottom about the same size does not respond at all across.
I've attached a picture as an example of which part of the screen highlighted in red does not respond at all to touch. Everything else not highlighted in red works fine.
Have used my mouse to access boot recovery mode, reinstalled hal 9k mod rom, wiped cache / data and it made no difference.
Even updated my MCU to the latest version available for HA unit, and attempted to re-calibrate the screen via extra settings.
Not sure if original factory rom will fix this, but would like some opinions.
maybe take it apart and check the screen connector is in correctly, sounds like a hardware not software problem.
darkphat said:
So, have a bit of a situation and not sure what to do.
My touch screen is working, but only to a point. Only the top status bar and bottom about the same size does not respond at all across.
I've attached a picture as an example of which part of the screen highlighted in red does not respond at all to touch. Everything else not highlighted in red works fine.
Have used my mouse to access boot recovery mode, reinstalled hal 9k mod rom, wiped cache / data and it made no difference.
Even updated my MCU to the latest version available for HA unit, and attempted to re-calibrate the screen via extra settings.
Not sure if original factory rom will fix this, but would like some opinions.
Click to expand...
Click to collapse
Hi,
I have similar problem on my px5 seicane unit. the bottom part touch screen won't response or acting without touch after wake up from sleep. restart the unit would result the issue.
wondering if you have resolved the problem? If so is that hardware issue?
just realized the touch screen issue I have on my headunit is probably hardware issue.
in the past I have to re-start the unit, that actually fixed the problem, don't know why. but now I just push the touch screen with my palm firmly. that would fix the problem as well, and last much longer (3-5 days). haven't get chance during the weekday to open up the unit. but at least it worked. and probably proofed this is hardware issue.
I have a Joying unit with a PX5 board. I also have the same issue as the original poster.
I would also say this is a hardware issue. Mine was fine with both the original PX3 and PX5 for a while. Now it is increasingly getting worse. Resets do nothing to solve the problem.
I live in a hot environment. Maybe that is a contributing factor?
Hi all. Im hoping someone here has experience or can point me in the right direction.
I just installed a Joying 6.2 inch tablet with physical buttons in my car. At first for roughly an hour everything seemed to work. Then I lost access to thephysical softouch home button and then I lost access the the navigatiom button. They simply stopped responding to input. The screen portion itself still responds fine and recalibrating the screen didnt fix it nore did a reset with the pin hole. Has any body run into this and if so how did you fix it. I hate to send itback asbesides this it works fine.
Thanks for any and all help.
Dan