Database Info

FIXED: Lg g flex 2 H959 32GB Model , Partition damage:only 8GB available ?

Hi everyone,
I have LG H959 version of G Flex 2.
I recently used LG Flash tool 2014 to flash a stock H959 firmware version 5.1.1 of android since it wasn't available through OTA.
My problem is I accidentally downloaded H955 firmware from http://lg-phone-firmware.com/ and then I realised I didn't have network connectivity so I checked the version and saw the H955, then I when reverted back to original firmware of H95910D_00 and saw I only have 8GB available and under Misc menu of Storage information there is around 24GB of system data allocated which before was 8GB.
How can this happen. I flashed the firmwares with CSE and I have also extracted the kdz files and found there are partition table bin files available.
So I tried getting fastboot working but I had no luck. I boot into download mode and can't even root the phone following the guidance available on http://forum.xda-developers.com/android/development/guide-root-method-lg-devices-t3049772
I can use the phone just fine, every functionality works but only 8GB storage available
EDIT: FIXED
Here's how I fixed my problem: Be Aware you will loose all your data on internal storage and this is a dangerous operation
1- First you need the LG Root files from http://forum.xda-developers.com/android/development/guide-root-method-lg-devices-t3049772
2- Then if you are lucky you may not need to flash H95910C firmware and root your phone first, So go ahead and Boot the phone into download mode (Power off the device, hold the upper volume key and plug the phone usb into computer), open command prompt in your LG Root folder and
type: [ports.bat ] : Find the COM port where your phone is connected with line DIAG in it.
type: [Send Command //./COM(your port number)] : You now have a shell and can send commands to your device
type: [ cat /proc/partitions] and [ cat /proc/mounts ] and [ df ] : Now find which mmcblk0p* is your userdata at.
Mine(Lg-H959) is at mmcblk0p48 so then go ahead and type [ dd if=/dev/zero of=/dev/block/mmcblk0p48]
3- Now if this is working then it will appear as if the shell has stopped working and you can't send any more commands, give it a few minutes then do Ctrl + C to terminate the "Send Command" reboot your phone into recovery (Hold power + Volume Down until LG logo appears then release and press again only the power button until you are at factory reset prompt screen. Click on yes using volume and power keys and this should be it. You should have the right size available.
If Your phone didn't became solved then you have to Flash H95910C frimware and root the phone
4- So do all the step 1 & 2 & 3 but before sending the [ dd if=/dev/zero of=/dev/block/mmcblk0p48] do [ su ] first.
LG Flash tool and LG Root are attached here.
You can get the H95910C from here : https://mega.nz/#!EZ81hapC!y8b_hnyGIchnzyBK46cXuZlUxD8S5Gpg44ULck-pgSI
You're welcome.

http://forum.xda-developers.com/g-flex2/help/23gb-data-usage-t3123072

ddfzl said:
http://forum.xda-developers.com/g-flex2/help/23gb-data-usage-t3123072
Click to expand...
Click to collapse
Link is not helpful, but I see that other people have had my problem too.

Its Works ,
Now free space is 21.93GB
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
thanks

RinXPERIA said:
Its Works ,
Now free space is 21.93GB
View attachment 3413831
thanks
Click to expand...
Click to collapse
Very well, you are welcome [emoji3]
Sent from my LG-H959 using Tapatalk

Oh my God.....!!!!!When i wake up early morning.Perfect i have running Step 1,2 and can not boot to recovery factory reset.My phone boot directly to OS and i have 22,10GB.Many Thanks!!!!!!!
---------- Post added at 09:57 AM ---------- Previous post was at 09:34 AM ----------
I have one problem.When i flash firmware H959 to F510L.When my phone booting to OS this screen always show warning "Current version is not avaiable for user.Can't Find matched cust for NT-Code mcc/mnc, subnet"Everybody can help me to solve it...Many thanks>>>:good:

alibabahp said:
Oh my God.....!!!!!When i wake up early morning.Perfect i have running Step 1,2 and can not boot to recovery factory reset.My phone boot directly to OS and i have 22,10GB.Many Thanks!!!!!!!
---------- Post added at 09:57 AM ---------- Previous post was at 09:34 AM ----------
I have one problem.When i flash firmware H959 to F510L.When my phone booting to OS this screen always show warning "Current version is not avaiable for user.Can't Find matched cust for NT-Code mcc/mnc, subnet"Everybody can help me to solve it...Many thanks>>>:good:
Click to expand...
Click to collapse
That happened to me when I flashed H955 on H959, All I know so far is that "Cust" is actually a partition in the devices with some manufacturer stuff on it, so I guess it won't flash with a new one when you flash the firmware H959 to F510L. My best advice is to flash your own model firmwares.

Afshin44 said:
That happened to me when I flashed H955 on H959, All I know so far is that "Cust" is actually a partition in the devices with some manufacturer stuff on it, so I guess it won't flash with a new one when you flash the firmware H959 to F510L. My best advice is to flash your own model firmwares.
Click to expand...
Click to collapse
I have forget backup my NT CODE in my F510L with command 277634#*510#.I Think NT code can rewrite or change from backup.Now my NT Code is 0,fffff,fffffffff,fffff.

This isn't working in a H955P, I did flash the original firmware and still saying 8.91 userdata. Any ideas how can this fix be compatible with H955P/16GB/2GB ?

HKreutz said:
This isn't working in a H955P, I did flash the original firmware and still saying 8.91 userdata. Any ideas how can this fix be compatible with H955P/16GB/2GB ?
Click to expand...
Click to collapse
If you follow the instructions, It would work for any model of G Flex 2. Be careful to first find which mmcblk your data partition is at using the instructions I have given then when you do the dd if=/dev/zero of=/dev/block/mmcblk0p48 change "48" with the number from your model.

hi , i need h959 10C rom this link dead. Can you share h959 10C rom please
on dropbox or google drive

hello
anybody has h959 10C FIRMWARE .KDZ FILE?
I NEED THAT FILE BUT link dead
can you upload on google drive or dropbox?
thanks

fedele02 said:
hi , i need h959 10C rom this link dead. Can you share h959 10C rom please
on dropbox or google drive
Click to expand...
Click to collapse
I will upload it tomorrow. I just saw this.

thanks , i am waiting :good:

afshin44 when will you upload ?
i am still waiting
i really need that rom
please....

THx u so much for v10c

Internal Storage is Damaged on G6 U10

HI there I'm new here but this forum is very informative tnx.
Here is the problem:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Image URL: http://cld.persiangig.com/download/GsIv0k/dl
Do u have any solutions please?
I have tried Flashing and ROM ... but no results..
What about this: http://forum.xda-developers.com/showthread.php?t=1838204 ???

i have same problem will any body give answer ?

i have same problem

Solved?
SepehrAzureSky said:
HI there I'm new here but this forum is very informative tnx.
Here is the problem:
Image URL: http://cld.persiangig.com/download/GsIv0k/dl
Do u have any solutions please?
I have tried Flashing and ROM ... but no results..
What about this: http://forum.xda-developers.com/showthread.php?t=1838204 ???
Click to expand...
Click to collapse
Have you solved this problem?

may be hardware problem

igor.smiljanic said:
Have you solved this problem?
Click to expand...
Click to collapse
No.. Not solved yet. Desperately looking for a solution.

maxprono1 said:
may be hardware problem
Click to expand...
Click to collapse
Yes. It is a hardware problem. As far as I know there are two options, either changing the hardware nor mounting a apart of SD Card as Internal Memory. First one is useless as it is costly and results might not be conclusive. However, I think, the latter might be applicable. But I don't know how. I would appreciate any help regarding this. Thank you.

This has happened to me too, I need help!

Please help
I do faced the same problem, anyone come out a solution please,appreciate!!

FOR EVERYBODY WITH THIS PROBLEM, TRY THESE STEPS:
(if you can/have your bootloader unlocked & you can unstall U10 or L11 roms then download the U10 slimstock, or L11 deodexed rom)
- download G6 knife (pinned post in the facebook group)
- open G6 knife > download offical U10 rom (if you had android 4.3 before your problem then download 4.3, if you had 4.4 download 4.4kitkat)
- format your sd, place the downloaded firmware on your sd:
SD/dload/update.zip (or SD:/HwOUC/update.zip depends if you are on android 4.3 or 4.4)
- insert sd and try to boot up your phone (without cable attached)
- if nothing happens open G6 knife again and boot your phone into fastboot and attach it to pc
- use G6 knife program to boot into recovery ( or do it with adb) (or hold vol+ power)
- select install zip from sd, select the update,
you can download g6 knife here:
https://www.facebook.com/groups/huawei.g6.development/permalink/462401503919107/
you can do all of this without G6 Knife, but this tool makes it alot easier cause you don't have to look for files or commands

washichi said:
FOR EVERYBODY WITH THIS PROBLEM, TRY THESE STEPS:
(if you can/have your bootloader unlocked & you can unstall U10 or L11 roms then download the U10 slimstock, or L11 deodexed rom)
- download G6 knife (pinned post in the facebook group)
- open G6 knife > download offical U10 rom (if you had android 4.3 before your problem then download 4.3, if you had 4.4 download 4.4kitkat)
- format your sd, place the downloaded firmware on your sd:
SD/dload/update.zip (or SD:/HwOUC/update.zip depends if you are on android 4.3 or 4.4)
- insert sd and try to boot up your phone (without cable attached)
- if nothing happens open G6 knife again and boot your phone into fastboot and attach it to pc
- use G6 knife program to boot into recovery ( or do it with adb) (or hold vol+ power)
- select install zip from sd, select the update,
you can download g6 knife here:
https://www.facebook.com/groups/huawei.g6.development/permalink/462401503919107/
you can do all of this without G6 Knife, but this tool makes it alot easier cause you don't have to look for files or commands
Click to expand...
Click to collapse
My device is not recognized by G6 knife.. even after using the f option, my phone does not ask for any USB debugging permission. Nothing happens.

SepehrAzureSky said:
My device is not recognized by G6 knife.. even after using the f option, my phone does not ask for any USB debugging permission. Nothing happens.
Click to expand...
Click to collapse
you can use g6knife to download firmware without attaching your phone,
you can use adb to boot into recovery and force it to update

washichi said:
you can use g6knife to download firmware without attaching your phone,
you can use adb to boot into recovery and force it to update
Click to expand...
Click to collapse
I had someone to install ROM before, but the problem did not resolve.
Do you think I can fix using this way? If yes, I would be thankful to tell me how. It is my first time. I am unfamiliar with the steps.
OK now, I installed the Knife; I plug my phone using USB cable; I run it, then I press 0 to verify the device. However, the program does not detect it.
Moreover, I have no access to my phone, and I cannot allow USB debugging through the phone.
I e-mailed HUAWEI they did not answer at all. It seems like no one can help God!

i ve got the same problem..plz can anyone help...i hav tried asz much options like hard reset.upload sdk..bt it wont work..plz anyone there to help

Came to this Facebook page, there is a few things you can try:
https://www.facebook.com/#!/Huawei-...w-unavailable-1705571879711006/?ref=bookmarks

I have the same problem. Did anyone manage to solve it?

bricked lg g flex 2

hi xda dev i have lg g flex 2 bricked when i was upgrading with lg flash tools2014 now he is showing on pc-manager (Qualcomm HS-USB QDLoader 9008) this probleme was sloved on lg g3 using BoardDiag my question is : can i unbrick my lg if i use lg g3 method just replacing img.file from my stock rom? i need help any suggestion???
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Help
I have the same brick here can somebody help

Not Yet Home Solution ! Only JTAG Via Soldering EMMC

only solution is here..
http://forum.gsmhosting.com/vbb/f672/worlds-first-lg-ls996-dead-boot-repair-done-2087401/

already fixed thnx anyway

and the link of dump file in the theard is expired so if any one want just contact me

younessaribey said:
already fixed thnx anyway
Click to expand...
Click to collapse
How did you fix it. can you upload procedure

rajan23 said:
How did you fix it. can you upload procedure
Click to expand...
Click to collapse
using the gsmhosting theared if u didn't find the dump file then i can upload it for u

younessaribey said:
using the gsmhosting theared if u didn't find the dump file then i can upload it for u
Click to expand...
Click to collapse
okay i will try to get it thanks

I have the solution for this brick
Just need somebody with a working sprint lg gflex 2
Follow these steps
Format your external MicroSD card with “exfat” system file, and the size of this SD card should be morethan 16 GB , which is the size of the whole partition.
Do a full factory reset, meaning wipe your cache, data, and internal storage using either CWM, TWRP, or PhillzTouch.
Insert the SD card to your phone and connect your mobile with ADB, type:
adb shell
su
dd if=/dev/block/mmcblk0 of=/storage/sdcard1/backup.img bs=512 count=30535646
The size of the “backup.img” is around 16 GB, However, if you compressed it, it would be around 2 GB.
Now, if you have the backup.img in your hand, you can do these steps:

sirwanesmail said:
Just need somebody with a working sprint lg gflex 2
Follow these steps
Format your external MicroSD card with “exfat” system file, and the size of this SD card should be morethan 16 GB , which is the size of the whole partition.
Do a full factory reset, meaning wipe your cache, data, and internal storage using either CWM, TWRP, or PhillzTouch.
Insert the SD card to your phone and connect your mobile with ADB, type:
adb shell
su
dd if=/dev/block/mmcblk0 of=/storage/sdcard1/backup.img bs=512 count=30535646
The size of the “backup.img” is around 16 GB, However, if you compressed it, it would be around 2 GB.
Now, if you have the backup.img in your hand, you can do these steps:
Click to expand...
Click to collapse
Waiting devices ( Qualcoom Loader 9008 (

https://yadi.sk/d/fLQj0wztvQ4aC
Its a dump of mmcblk0 I made it personally on rooted phone Ls996 with stock ZV8 firmware by command
dd if=/dev/block/mmcblk0 of=/storage/sdcard1/XXXXXX.img

lg gflex 2 dead after flashing
flashed kdz file on my lg gflex 2 after the finish fone goes dead not entrng download mode no response mobile cmpletly dead

[GUIDE] Fixing hard bricks [Qualcomm HS-USB QDLoader 9008]

Fixing dead L70+ devices​
EVERYTHING IN THIS GUIDE IS DANGEROUS AND CAN COMPLETELY DESTROY YOUR DEVICE IF DONE INCORRECTLY. YOU HAVE BEEN WARNED
PLEASE READ EVERYTHING​
DO NOT DO THIS IF IT'S ONLY A SOFT BRICK!!!
By following this guide you agree that I TAKE NO RESPONSIBILITY FOR BRICKED OR DAMAGED DEVICES.
You and only you decided to follow these instructions.
Click to expand...
Click to collapse
What is a dead (hard bricked) device?
A dead or "hard" bricked device is a device that has been bricked beyond repair. Usually a corrupted boot partition failing to load the kernel or any type of recovery menu in order to restore. Motherboard swap is most commonly done in order to fix such device. Some devices such as our own have "leaked" service packages that can be used to restore a hard bricked device. Beware that this is not a 100% guarantee. It might or might not work.
Click to expand...
Click to collapse
How do I know if my device is hard bricked?
It would fail to boot and enter recovery/download mode. When connected to a PC and powered on Windows will detect it as Qualcomm HS-USB QDLoader 9008.
Instructions​
Download and install drivers from here
Download BoardDiag v2.99a from here
Download TOT files from here
Unpack all archives in a new folder in the root of your C: drive. Everything including the tot file.
Remove the batter from the device
Plug the device in to the PC via the USB cable.
Place battery back
Open BoardDiag and set it up as such:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AP Chipset: W3 W5 (ms8610)
Com Port: Get port num from device manager.
Target Dir: The new folder you created in the root of C:
BIN: Select .tot file
DIR: The new folder you created in the root of C:
Click to expand...
Click to collapse
Click on the EXTRACT button and wait until it finishes.
Make sure there are ticks on AP Check and EMMC Test !
Press START and wait until the program finishes.
When done it's safe to disconnect the phone from the PC.
Pull the battery out and place it back in and try to enter Download mode. If successful you should be able to flash KDZ following this guide.
Translated and re-formatted. Original guide by @kossrap @ 4pda.
Happy flashing!

Reserved

Reserved 2

Great to have new tools with Qualcomm chipsets

The BoardDiag have no "msm8916"

hi, I tried this guide, but I could not get my lg d290n, ap test ok, EMMC ..test failed test, dsram okay, where am I wrong? someone can help me because I'm not very good?

marcello1977 said:
hi, I tried this guide, but I could not get my lg d290n, ap test ok, EMMC ..test failed test, dsram okay, where am I wrong? someone can help me because I'm not very good?
Click to expand...
Click to collapse
Check here: http://forum.xda-developers.com/d290n/how-to/guide-reflashing-stock-rom-d290-d295-t3142456

I have this problem 3 months ago , but i dont found solution yet for my Samsung -SM-N910F , sorry for my bad english :/

Need help please. I can't find the COM Port of my device. It just says "QHSUSB_BULK" under other devices. Doesn't say the port number. Anyone can help?

How to flash for htc one m8 in hsush qdload 9998
Sent from my HP 7 VoiceTab using XDA Free mobile app

Please Help
This happened after I clicked the start button...
please help

im trying to fix two LG fino with this one.
both were successful but I am still unable to boot to download mode

s4h1k0 said:
im trying to fix two LG fino with this one.
both were successful but I am still unable to boot to download mode
Click to expand...
Click to collapse
If you can boot in system, you can enable developer settings, connect the phone to your pc and try "adb reboot edl"

sorry it seems that I missed some steps.
I still cant go to downlaod mode

s4h1k0 said:
sorry it seems that I missed some steps.
I still cant go to downlaod mode
Click to expand...
Click to collapse
I think you need to restore the files using restore boot img, check this guide http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359

Hi My phones Lg G Pad 10.1 LG-VK700 hard brick after me flashing rom wrong Can u help me How to fix it ? Thank for help
lamyean122gmail.com

dibowz said:
This happened after I clicked the start button...
please help
Click to expand...
Click to collapse
I'm having the same problem as yours, does anyone have a solution? thanks, need help

Is this compatible with lg l fino d290n? And if yes, why the TOT file to download has the name "LGD295V10eCIS.7z"?
Sorry for my English

Hello, this method and post files can be used for a LG L70 MS323 v10c Metro PCS, sorry for my English...

Can i use provided D295N .tot file on a D290G?

Development Moto G Stylus (2021) firmware available [via Lolinet Mirrors]

https://mirrors.lolinet.com/firmware/motorola/minsk/official/

Stock firmware should be available through LMSA's Flash rescue option
Rescue and Smart Assistant (LMSA)(Motorola/Lenovo Only)
Rescue and Smart Assistant LMSA: Lenovo's Motorola Smart Assistant (PC) For Lenovo and Motorola Devices Only Rescue and Smart Assistant (LMSA) is an official tool installs on PC. Can help to manage smart device (include all Lenovo android phone...
forum.xda-developers.com

Thank you @peajul @sd_shadow
Which one of these folders contains the super.img file?

lebigmac said:
Thank you @peajul @sd_shadow
Which one of these folders contains the super.img file?
Click to expand...
Click to collapse
Not sure what you mean? LMSA or ?

I am searching for the super.img file from the official motorola firmware for this motorola device so I can flash it to this block device:
Bash:
ls -Al /dev/block/by-name | grep "super"
Does this motorola device even have a super partition in Android 10 or newer?

lebigmac said:
I am searching for the super.img file from the official motorola firmware for this motorola device so I can flash it to this block device:
Bash:
ls -Al /dev/block/by-name | grep "super"
Does this motorola device even have a super partition in Android 10 or newer?
Click to expand...
Click to collapse
C:\ProgramData\LMSA\Download\RomFiles

lebigmac said:
I am searching for the super.img file from the official motorola firmware for this motorola device so I can flash it to this block device:
Bash:
ls -Al /dev/block/by-name | grep "super"
Does this motorola device even have a super partition in Android 10 or newer?
Click to expand...
Click to collapse
Normally you would use fastboot like
Code:
fastboot flash super super.img_sparsechunk.0
fastboot flash super super.img_sparsechunk.1
fastboot flash super super.img_sparsechunk.2
fastboot flash super super.img_sparsechunk.3
fastboot flash super super.img_sparsechunk.4
And so on depending on how many chunks there are.

oh what a mess!
Where can I download these sparsechunks? I checked the download link above but couldn't find the sparsechunks.
And is there a way to merge all these sparsechunks into one single super image and flash it like this?
Bash:
fastboot flash super super.img

lebigmac said:
oh what a mess!
Where can I download these sparsechunks? I checked the download link above but couldn't find the sparsechunks.
And is there a way to merge all these sparsechunks into one single super image and flash it like this?
Bash:
fastboot flash super super.img
Click to expand...
Click to collapse
No, the device cannot handle the whole image at once, that's why it's split up.

peajul said:
https://mirrors.lolinet.com/firmware/motorola/minsk/official/
Click to expand...
Click to collapse
Hey, I have a Moto G Stylus 2021 Edition. I haven't done rooting in quite a while. I click on this folder and I'm presented with several folders. I'm using an unlocked version of the Moto Stylus 2021. However, I see "MetorPCS", "Tracfone" etc. I initially tried downloaded MetroPCS thinking it was carrier specfic. I copied this zip onto the folder on my phone. I ran Magisk and tried to install by selecting that zip. It tries to unpack then gives me an error.
I'm assuming that I'm doing something wrong.

steppinthrax said:
Hey, I have a Moto G Stylus 2021 Edition. I haven't done rooting in quite a while. I click on this folder and I'm presented with several folders. I'm using an unlocked version of the Moto Stylus 2021. However, I see "MetorPCS", "Tracfone" etc. I initially tried downloaded MetroPCS thinking it was carrier specfic. I copied this zip onto the folder on my phone. I ran Magisk and tried to install by selecting that zip. It tries to unpack then gives me an error.
I'm assuming that I'm doing something wrong.
Click to expand...
Click to collapse
Try LMSA'S rescue to get the correct boot.img
[Guide] Root Motorola with Magisk (UnLocked Bootloader)(Non-TWRP method)
Root Motorola Devices with Magisk Note: This method has been working with most Moto Devices that the Bootloader can be UnLocked. If the Bootloader cannot be Unlocked this method will not work. Please only use this as a reference. If you require...
forum.xda-developers.com

sd_shadow said:
Try LMSA'S rescue to get the correct boot.img
[Guide] Root Motorola with Magisk (UnLocked Bootloader)(Non-TWRP method)
Root Motorola Devices with Magisk Note: This method has been working with most Moto Devices that the Bootloader can be UnLocked. If the Bootloader cannot be Unlocked this method will not work. Please only use this as a reference. If you require...
forum.xda-developers.com
Click to expand...
Click to collapse
Thanks,
I download the Lenovo Smart assistant. It identifies my phone make/model. This is what I see within the Smart Rescue Area. I can go back to upgrade and it has my make model etc.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

steppinthrax said:
Thanks,
I download the Lenovo Smart assistant. It identifies my phone make/model. This is what I see within the Smart Rescue Area. I can go back to upgrade and it has my make model etc. View attachment 5366121
Click to expand...
Click to collapse
No, close and reopen,
Select rescue

sd_shadow said:
No, close and reopen,
Select rescue
Click to expand...
Click to collapse
That's what I did, unless I have the wrong software. I selected this "Rescue" Button below, but I get what I posted int he previous screen.

steppinthrax said:
That's what I did, unless I have the wrong software. I selected this "Rescue" Button below, but I get what I posted int he previous screen.
View attachment 5366123
Click to expand...
Click to collapse
Connect phone while it's in fastboot mode

sd_shadow said:
Connect phone while it's in fastboot mode
Click to expand...
Click to collapse
I think I figured out my problem. I had an old junkie version of the software. I'm downloading my ROM now. I will proceed with rooting shortly.

I was able to recover after a dynamic system update and a factory locked bootloader w/ no root using LSMA, Lenovo smart assistant didn't work, but the more updated LSMA from Motorola's support website worked.