Hi, I've got an old S5 with a broken screen. There's no image going on and there's no indication that the touchscreen is working.
I'm not looking to recover data, I'm looking to play around with it by controlling it from my PC. Last I remember, the phone is running a Cyanogenmod OS (I don't think LineageOS was around at that time) with either TWRP or CWM recovery, but I'd bet on TWRP.
Now: the device reaches the OS properly, I can tell because if I try to turn the ringing sound up it gives me an audio feedback.
If I connect it to a PC from the OS:
- the phone shows up in Windows Explorer as "SM-G900F"
- Device Manager shows me a "SAMSUNG Mobile USB Composite Device" under Universal Serial Bus controllers
However I cannot access any files (Windows Explorer shows the device as empty), and if I attempt to 'adb devices' in the console it shows me an empty devices list.
Now, I suspect that USB debugging might be off. So I also tried connecting it to a PC from recovery and the exact same thing as above can be observed, PLUS:
- Device manager also shows me a "SAMSUNG Android Phone" list which can be expanded to show me one entry called "SAMSUNG Android ADB Interface"
However it's the same as before, no files available and 'adb devices' shows an empty list.
Now I heard that I can theoretically enable USB debugging through ADB, by writing to a config file. That would allow me to enable USB debugging and try something like Vysor in order to control the phone from my PC.
However that's a moot point until I can figure out why the ADB service on my PC isn't seeing the device. Any help would be greatly appreciated, and if you need more info I can provide it.
Extra info:
- I installed Samsung USB drivers at some point while trying to make it work
- Windows Explorer shows a phone icon for this device, and if I recall correctly that's what happens when it's connected through MTP (Mass Storage should show it like a memory card)
_sepiroth said:
Hi, I've got an old S5 with a broken screen..........
Click to expand...
Click to collapse
I've never experienced this situation myself but, I've seen that the following thread has worked for many individuals.
https://forum.xda-developers.com/showthread.php?t=2786395
Good Luck!
~~~~~~~~~~~~~~~
Unless asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX Forum App on my Apple Macintosh.
Ibuprophen said:
I've never experienced this situation myself but, I've seen that the following thread has worked for many individuals.
https://forum.xda-developers.com/showthread.php?t=2786395
Good Luck!
~~~~~~~~~~~~~~~
Unless asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX Forum App on my Apple Macintosh.
Click to expand...
Click to collapse
Thanks a bunch, that pointed me in the right direction with my research! I solved my issue, I can now control my phone from my PC.
By doing this I ran into a couple of problems, I'm going to describe them and their solutions:
Problem 1: couldn't ADB into the device when in Recovery Mode. That is because after a long head scratching session I came to the conclusion that I didn't have TWRP Recovery installed (I had Philz Touch CWM Recovery and LineageOS 14.1 instead).
Solution 1: ADB mode is enabled in TWRP by default. So I flashed the latest TWRP through Odin, ADB instantly started working afterwards in Recovery Mode.
Problem 2: USB Debugging was disabled inside the OS.
Solution 2: from the thread that Ibuprophen posted, you can enable USB debugging in your OS by opening an ADB shell into your device and modify the build.prop like so
Code:
Adb shell
echo "persist.service.adb.enable=1" >>/system/build.prop
echo "persist.service.debuggable=1" >>/system/build.prop
echo "persist.sys.usb.config=mass_storage,adb" >>/system/build.prop
reboot
Problem 3: /system was empty so there was no build.prop. If I attempted to create a build.prop file it wouldn't be saved after a device reboot, so USB debugging still didn't work.
Solution 3: it seems like TWRP doesn't mount /system by default, only /data. You can mount it manually through ADB like this:
Code:
mount -o rw /dev/block/bootdevice/by-name/system /system
I found this out from this stackexchange question: https://android.stackexchange.com/q...data-partitions-in-recovery-mode-in-adb-shell
Problem 4: When an app tries to use USB Debugging you need to allow it to do so from the phone. Since the screen was broken, I couldn't do this.
Solution 4: You'll need to push a public key to your device with ADB. Boot into Recovery Mode and make sure your device is recognized by your PC and type
Code:
adb push <path to adbkey.pub on your PC> /data/misc/adb/adb_keys
This solution is from: https://stackoverflow.com/questions...b-rsa-key-with-broken-touch-screen-on-android
This will make sure that you won't need to confirm debugging permissions for apps coming from your machine.
So for anyone who has a broken phone screen (my screen is dead and touchscreen/touch buttons are kaput too) and wishes to control their phone from their PC but USB debugging is disabled:
1. Boot device in TWRP Recovery (flash it if you don't have it)
2. ADB into the device
3. Make sure /system is mounted (if it's empty it means it's not mounted), else mount it manually like in Solution 3
4. Configure build.prop to have USB Debugging enabled like in Solution 2
5. Push your public key to the device like in Solution 4
6. Restart the phone (into its OS)
7. Download the Chrome extension called Vysor and launch it
8. Connect your phone through a USB cable
9. The device should appear in Vysor, connect to it and have fun controlling it
Note that if you just want to backup your files, steps 1 + 2 are sufficient. After making sure ADB works you can just 'adb pull' all your files which should be located in /sdcard. Google it, it's easy to find.
The same goes for backups, you can do them directly through ADB.
Again, thanks Ibuprophen!
Vysor does not work on all graphic cards. a good free alternative is scrcpy
btw instead of flashing twrp, you can flash a modified system partition with proper entries in build.prop (for those with no custom recovery available)
aIecxs said:
Vysor does not work on all graphic cards. a good free alternative is scrcpy
btw instead of flashing twrp, you can flash a modified system partition with proper entries in build.prop (for those with no custom recovery available)
Click to expand...
Click to collapse
Very well pointed out, thanks for this.
Related
**UPDATE**
NEW VERSION
THIS RELIES ON ADB COMMANDS, SO IF YOU DO NOT HAVE USB DEBUGGING TURNED ON, OR A CUSTOM RECOVERY TO BOOT TO, THEN IT WILL NOT BE AS SIMPLE AS JUST RUNING THE PROGRAM.
Another user was having issues because he had an emulator installed, so I updated the file to give you the choice between an emulator, or device. I intend to update further to allow you to check for and select an individual device, that will come soon..
----------------------------------------------------------------------------------------------------------------
Recently my Galaxy s2's screen smashed, and, after replacing it with a GS4, i realized that many of my pictures were stuck on the internal sd card of the GS2. Being unable to turn on mass storage mode, I made a very simple tool that makes using adb pull a simple, painless process, even for the most computer illiterate of android users. Hope this helps if anyone needs it.
For anyone having issues...
If you had not previously activated USB Debugging, there are several steps you need to follow in order to enable ADB
SCREEN WORKING TOUCH BROKEN NO CUSTOM RECOVERYfirst, if you can see your screen, and have access to an otg cable, plug a mouse in to the otg cable, and the otg cable into the phone. Use the mouse to enable USB debugging, or to transfer files.
HOW TO ENABLE USB DEBUGGING
SCREEN WORKING TOUCH BROKEN WITH CUSTOM RECOVERYboot to your custom recovery ADB commands will work here. (usually hold vol- + pwr)
HOW TO BOOT TO RECOVERY
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
SCREEN BROKEN TOUCH BROKEN WITH CUSTOM RECOVERYboot to your custom recovery ADB commands will work here. (usually hold vol- + pwr)
HOW TO BOOT TO RECOVERY
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
SCREEN BROKEN TOUCH BROKEN NO CUSTOM RECOVERYnow things get complicated...
*The following is paraphrased from this site
1. download the custom recovery image for your device. Copy the recovery image to a convenient location on your computer, preferably with a short path. We will be placing it on the C Drive directly (not in any folder) and using that in the next steps.
Note: The recovery image should have .img extension. If it is in a zip file, extract the .img file from it.
I recommend clockwork mod non touch from this page
2. Power your device off and reboot your device to FASTBOOT or DOWNLOAD MODE depending on which type of device you have.
(most devices are fastboot, SAMSUNG typically uses DOWNLOAD MODE)
how to boot to fastboot or download mode
[FASTBOOT]3. Connect your device to your computer via USB and wait till you see the PC recognize the device
to check if your device is in fastboot and connected use CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
fastboot devices
you will see a list of connected devices. if not, something went wrong.
4. Launch Command Prompt and type the following commands;
cd c:\android (this is your ADB path, c:\android is default)
fastboot flash recovery c:\recovery.img
5. Wait for the process to finish.
6. Turn device off then boot to your custom recovery ADB commands will work here. (usually hold vol- + pwr)
HOW TO BOOT TO RECOVERY
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
[RECOVERY MODE (SAMSUNG)]USE THE INSTRUCTIONS ON THIS PAGE
Once in custom recovery, connect the device to the PC.
open CMD and enter the following commands;
cd c:\android (this is your ADB path, c:\android is default)
adb devices
The result should be something like
List of devices attached
051a4dd5 recovery
^^this number will be different for you
if you get a result on ADB devices, then you can use the program
HOPEFULLY THIS HELPS. REMEMBER TO CHECK THE FORUM PAGE FOR YOUR DEVICE IF YOU RUN INTO ISSUES. THIS ISN'T ANYTHING THE MEMBERS OF XDA HAVEN'T DONE THOUSANDS OF TIMES OVER.
Don't forget to hit "Thanks"
i'll bump this thread for those who didn't see this amazing tool, this tool is really useful, thank you very much
Hi,
Sturggling to find the .adb file as my phone shows up as a "Portable Device" any ideas?
Cheers
Thank you!
I joined just to say thank you to FuzzyMeep Two. Thanks for an awesome tool! It worked better than advertised!
:good:
Thanks again!
-th3r3isnospoon
Question
Hi! Can I use that to restore data not from sdcard but from internal memory of the device? I was storing photos on device memory on my Asus TF300T and now its bricked. I need to restore these photos, my girlfriend has something like 1000 of them from her trip to Caracas. Its very important for her. I already managed to connect the device through fastboot and I launched anb in cmd. What should I do next? Please help me guys
koperkowy said:
Hi! Can I use that to restore data not from sdcard but from internal memory of the device? I was storing photos on device memory on my Asus TF300T and now its bricked. I need to restore these photos, my girlfriend has something like 1000 of them from her trip to Caracas. Its very important for her. I already managed to connect the device through fastboot and I launched anb in cmd. What should I do next? Please help me guys
Click to expand...
Click to collapse
Yes, when it references SD Card it means the internal "SD" storage built in to the phone, not the removable one. It should work as long as ADB can connect.
Sorry for taking so long to reply, i really hope you got your pictures back.
FuzzyMeep Two said:
Recently my Galaxy s2's screen smashed, and, after replacing it with a GS4, i realized that many of my pictures were stuck on the internal sd card of the GS2. Being unable to turn on mass storage mode, I made a very simple tool that makes using adb pull a simple, painless process, even for the most computer illiterate of android users. Hope this helps if anyone needs it.
P.S. I apologize if i have posted this in the wrong place, if so please let me know.
Click to expand...
Click to collapse
Really great stuff - so simple but so effective. Cheers and thanks.
Error msg
zobes said:
Really great stuff - so simple but so effective. Cheers and thanks.
Click to expand...
Click to collapse
When i run that tool, i get the error mesg: more than one device and emulator,
I dont want to uninstall the emulator coz it was a headache getting it running
How i procede to select the device to be used
alisdairjk said:
When i run that tool, i get the error mesg: more than one device and emulator,
I dont want to uninstall the emulator coz it was a headache getting it running
How i procede to select the device to be used
Click to expand...
Click to collapse
NEW VERSION
Try this, i haven't gotten to test it, so please let me know if it worked for you, I added the option of selecting an emulator or USB device, because of your post. Hopefully it helps.
When I try to run this I also get an error message saying that the adb.exe file cannot be found.
Please can anyone help?
Joeb29 said:
When I try to run this I also get an error message saying that the adb.exe file cannot be found.
Please can anyone help?
Click to expand...
Click to collapse
Have you also installed ADB, as well as this software?
I'm also having an issue - I have installed java, java SDK and ADB, so I can now run the data recovery tool. But when I do I'm getting "error:device not found" - am I missing drivers or something? I couldn't get all the way on the ADB configuration, because part of it required me to do something on the device... anyway, looks like the computer isn't recognising the the phone at the moment.
Any help very gratefully received (phone is Samsung Galaxy S2).
joffmeister said:
Have you also installed ADB, as well as this software?
I'm also having an issue - I have installed java, java SDK and ADB, so I can now run the data recovery tool. But when I do I'm getting "error:device not found" - am I missing drivers or something? I couldn't get all the way on the ADB configuration, because part of it required me to do something on the device... anyway, looks like the computer isn't recognising the the phone at the moment.
Any help very gratefully received (phone is Samsung Galaxy S2).
Click to expand...
Click to collapse
I have the same situation right now. Managed to make your program work then I get the "error:device not found". My phone does show up in the computer folder(albeit not in mass storage mode), but isn't that what this program was made to work around?
My phone is a LG Optimus G with a smashed glass... The LCD still displays fine, but I'm stuck at my swipe lock because the digitizer is dead.
Thank you for your help and your wonderful program.
Thanks for this app. My girlfriend broke her screen and digitizer on her Galaxy S4. She never turned USB Debugging mode and has a lock on her screen. When using your app I get the same error when I use adb by itself which is "error: closed". ADB detects my phone but any command I use in ADB or with your app I get that same error.
Do you know how to fix this? Thanks in advance.
Thanks a lot man.
dude this tool is just amazing and does exactly what it promised. I was spending sleepless nights thinking about how to recover my data from my broken galaxy nexus and now that I have it I can rest easy. Seriously can't thank you enough for this. Just joined xda to thank you buddy.:laugh::fingers-crossed:
Getting an error "The system cannot find the path specified."
I start the recovery tool, set eh adb path successfully, and then I get this error. If I try running the recovery to pull the DCIM library I get this:
"error: device not found"
What can I do?
Thanks!
Either way this is an amazing tool, seeing how it helped some people already. :good:
Hi, Seem to have the same problem as many others, Device not found. I cant change to MTP mode on my LG G2.
I hope someone can find a solution to this problem.
Program seems amazing doh.
Hello,
This is really a great tool ! I was wondering if you could add the possibility to recover the external sd card aswell.
Device not found
Tried to recover a Samsung Galaxy S3 mini with a broken screen
I installed adb and RecoverData, run it and then get a "device not found error"
What can I do?
Amazing app. thank you so much :good:
FuzzyMeep Two said:
**UPDATE**
NEW VERSION
Another user was having issues because he had an emulator installed, so I updated the file to give you the choice between an emulator, or device. I intend to update further to allow you to check for and select an individual device, that will come soon..
----------------------------------------------------------------------------------------------------------------
Recently my Galaxy s2's screen smashed, and, after replacing it with a GS4, i realized that many of my pictures were stuck on the internal sd card of the GS2. Being unable to turn on mass storage mode, I made a very simple tool that makes using adb pull a simple, painless process, even for the most computer illiterate of android users. Hope this helps if anyone needs it.
Don't forget to hit "Thanks"
Click to expand...
Click to collapse
Hi, Thank you very musch, It's so usefull for me.. :angel:
Hi
I have a old nexus with broken touchscreen . I want to use it via mirror on pc.
unfortunatly USB debuggin wasn't enable so i can't install any app.
any tips?
thanks
PS: i saw many use usb adapter to connect a mouse but i don't have it
EDIT: right now i just need a rom/kernel with USB debugging mode enabled by default
the screen still works , only the touch screen is broken
power , and volume bottons still work
the device is rooted
If it's only installing apps you could install them via recovery. (as zip)
Or you could check for a cheap replacement touchscreen.
nonameleft4me said:
If it's only installing apps you could install them via recovery. (as zip)
Or you could check for a cheap replacement touchscreen.
Click to expand...
Click to collapse
thanks for the answer!
sorry i forgot to mention that i need USB debuggin for make the app works correctly.
I'm trying now to find out what rom i have installed and maybe then find a kernel with OTG support . (yes i found a otg cable )
i'm not a expert of rooting
I think google has an app called voice control. Not sure how operational it is though. Supposedly you can control the entire system via voice.
nonameleft4me said:
I think google has an app called voice control. Not sure how operational it is though. Supposedly you can control the entire system via voice.
Click to expand...
Click to collapse
i need to unlock the phone and tap on the widget "search" to start voice command .
I think the best way is to find a way to enable OTG and then use a usb mouse
Boot into Recovery and mount*Data*partition.
Open a shell on PC and type:
adb pull /data/property/persist.sys.usb.config ~/
Repace*~/*with home directory of your OS.
Open that file in a text editor and you would possibly see*mtp*written there. Change it to*mtp,adb.
Note that sometimes Android doesn't understand the text file changes if the line terminator is "DOS Terminators" which Notepad would probably do on Windows (mine is Linux so no issue here).
In that case, I would suggest not using*adb pullbut doing:
adb shell echo 'mtp,adb' > /data/property/persist.sys.usb.config
You may verify that the*echo*command overwrote the file by using:
adb pull /data/property/persist.sys.usb.config ~/
and seeing the file's content in some text editor.
Unmount*Data*and reboot into Android OS. USB Debugging would probably be enabled.
Sent from my Aqua Trend using Tapatalk
Itzabhaysingj said:
Boot into Recovery and mount*Data*partition.
Open a shell on PC and type:
adb pull /data/property/persist.sys.usb.config ~/
Repace*~/*with home directory of your OS.
Open that file in a text editor and you would possibly see*mtp*written there. Change it to*mtp,adb.
Note that sometimes Android doesn't understand the text file changes if the line terminator is "DOS Terminators" which Notepad would probably do on Windows (mine is Linux so no issue here).
In that case, I would suggest not using*adb pullbut doing:
adb shell echo 'mtp,adb' > /data/property/persist.sys.usb.config
You may verify that the*echo*command overwrote the file by using:
adb pull /data/property/persist.sys.usb.config ~/
and seeing the file's content in some text editor.
Unmount*Data*and reboot into Android OS. USB Debugging would probably be enabled.
Sent from my Aqua Trend using Tapatalk
Click to expand...
Click to collapse
thanks!
i tryed
1) i went in recovery mode
2) i connect via usb the nexus4 to my pc
3)went in "mounts and storage"
4)then "mount /data"
5)in cmd i tryed your command "adb pull /data/property/persist.sys.usb.config" but i says i'm unauthorized
i checked via command "adb devices" and it return a alphanumerica string plus "unauthorized"
i tryed then to
Reboot your phone into recovery mode.
Connect it to your computer.
Open the terminal and type:
cd ~/.android
adb push adbkey.pub /data/misc/adb/adb_keys
adb shell reboot
but it still says error : device unauthorizated . please check the confirmation dialog on your device
i tryed also with a different version of adb and now gives me after "adb devices" an "offline" response
NB: if i connect the phone (not in recovery mode) via usb i can copy files in and out (i can explore onlyfew folders) , maybe this could help.
hartman11 said:
i tryed also with a different version of adb and now gives me after "adb devices" an "offline" response
NB: if i connect the phone (not in recovery mode) via usb i can copy files in and out (i can explore onlyfew folders) , maybe this could help.
Click to expand...
Click to collapse
Sorry but this could not help... Now only thing you can do is connect any USB mouse to your phone via otg cable (as it is not costly also), and you can also try USB gamepad. I also have used USB gamepad before when my touchscreen was not working.
Second thing you can do is download any android device manager for your PC like mobogenie or mobilego they directly install any app from play store to you android device, through USB.And I don't think they need USB debugging option to be enabled.
Sent from my Aqua Trend using Tapatalk
my problem is not installing an app (i could do it in recovery mode with a .zip) but enabling the USB debuggin
I have a otg cable but not the "Y" type ( the one with power source ) , also i don't know if OTG is supported by my kernel . I would like to install maybe another kernel which has OTG support and usb debuggin mode enable by default but i don't know what kind of rom i have D:
right now i just need a rom/kernel with USB debugging mode enabled by default
up
I have a Galaxy Note 5 and I have important data in it. The screen is broken so I can't do anything, but I see recovery listed with a bunch of characters when I do
Code:
adb devices
. I can run some adb commands, adb root tells me I have root, I can do "id" inside of adb shell. Though, whenever I try running any twrp commands inside adb shell, it says "TWRP does not appear to be running. Waiting for TWRP to start."
What can I do here? I also see SAMSUNG Android under devices on this linux distro I'm running but I am getting an mtp error whenever I try connecting to it.
Sorry to hear that. If your Samsung Galaxy Note 5 can be detected by the computer via USB cable connecting, and the USB debugging on it is enabled, try Coolmuster Android Backup Manager. Its free backup function can help transfer data to the computer for backup directly. It's easy and safe. Good luck to you.
nazhai said:
Sorry to hear that. If your Samsung Galaxy Note 5 can be detected by the computer via USB cable connecting, and the USB debugging on it is enabled, try Coolmuster Android Backup Manager. Its free backup function can help transfer data to the computer for backup directly. It's easy and safe. Good luck to you.
Click to expand...
Click to collapse
It doesn't seem to be working, well at least not when the phone's in recovery. I'm not sure if I can boot it up normally.
tesiz22 said:
I have a Galaxy Note 5 and I have important data in it. The screen is broken so I can't do anything, but I see recovery listed with a bunch of characters when I do
Code:
adb devices
.
Click to expand...
Click to collapse
Indicates your phone boots into Recovery mode and not into Normal ( ADB ) mode.
To get rid off of booting into Recovery mode you run
Code:
adb devices
adb reboot
Once your phone boots into Normal mode you can pull out the data of interest: take note that adb pull has a size limit, hence probably
Code:
adb pull /sdcard C:\PULLED-DATA
doesn't work as expected if amount of data to pull is >= 2GB in total ( e.g. a stored movie file may have up to 8GB ). That means, to be on safe side, you have to pull the files of interest one-by-one.
hi guys I need help to recover some personal photos I had saved on my device. The phone has a broken screen and touch so I cannot use a mouse or try to blindly unlock it, but it has been rooted and usb debugging is enabled; unfortunately my pc is not authorized by the phone and I have no way to authorize it through the pop up without a screen. I have searched around many forums to find a solution but it seems every time there was something wrong, so I need some help.
The solution that got me the nearest to a conclusion that I tried are:
using adb in custom recovery (which I do have) and trying commands like "adb pull /sdcard" which resulted in "pull: building file list... 0 files pulled. 0 files skipped.", I don't understand why it's unable to pull any file.
trying to authorize usb debugging for my pc through adb by "adb push adb_keys /data/misc/adb", adb_keys is the adbkey.pub file in the .android folder renamed. I can confirm i pushed them since "adb pull /data" pulled "data/adb/misc/adb_keys" as the only file, but I still don't have authorization
I'm not too literate in this kind of commands so please be patient but I really need help
RECAP OF MY PHONE STATUS
Xiaomi Mi 10 5G is the device
both screen and digitizer broken, I'm not able to see the screen or use touch (but I'm 100% sure the phone still works)
Android 12 rom (xiaomi.eu stable)
custom recovery available
rooted device
usb debugging enabled
no device authorized by the phone for usb debug
I found somewhere on xda that the problem could be solved by mounting/unmountind sdcard, but I have no ideea hoe to do that
damndaniel0 said:
hi guys I need help to recover some personal photos I had saved on my device. The phone has a broken screen and touch so I cannot use a mouse or try to blindly unlock it, but it has been rooted and usb debugging is enabled; unfortunately my pc is not authorized by the phone and I have no way to authorize it through the pop up without a screen. I have searched around many forums to find a solution but it seems every time there was something wrong, so I need some help.
The solution that got me the nearest to a conclusion that I tried are:
using adb in custom recovery (which I do have) and trying commands like "adb pull /sdcard" which resulted in "pull: building file list... 0 files pulled. 0 files skipped.", I don't understand why it's unable to pull any file.
trying to authorize usb debugging for my pc through adb by "adb push adb_keys /data/misc/adb", adb_keys is the adbkey.pub file in the .android folder renamed. I can confirm i pushed them since "adb pull /data" pulled "data/adb/misc/adb_keys" as the only file, but I still don't have authorization
I'm not too literate in this kind of commands so please be patient but I really need help
RECAP OF MY PHONE STATUS
Xiaomi Mi 10 5G is the device
both screen and digitizer broken, I'm not able to see the screen or use touch (but I'm 100% sure the phone still works)
Android 12 rom (xiaomi.eu stable)
custom recovery available
rooted device
usb debugging enabled
no device authorized by the phone for usb debug
Click to expand...
Click to collapse
There is a way to do it, but it costs money
@damndaniel0
If USB-MTP mode is enabled on phone - what should be default - then you can access all user-data stored in /storage/emulated/0 directory where among others photos are stored.
See also here:
MTP USB Device Driver Windows 10 64bit Driver | Device Drivers
MTP or (Media Transfer Protocol) is a set of custom extensions to the Picture Transfer Protocol (PTP) devised by Microsoft, to allow the protocol to be used for devices other than digital cameras, for example digital audio players such as MP3 players, and other portable media devices, for...
oemdrivers.com
xXx yYy said:
@damndaniel0
If USB-MTP mode is enabled on phone - what should be default - then you can access all user-data stored in /storage/emulated/0 directory where among others photos are stored.
See also here:
MTP USB Device Driver Windows 10 64bit Driver | Device Drivers
MTP or (Media Transfer Protocol) is a set of custom extensions to the Picture Transfer Protocol (PTP) devised by Microsoft, to allow the protocol to be used for devices other than digital cameras, for example digital audio players such as MP3 players, and other portable media devices, for...
oemdrivers.com
Click to expand...
Click to collapse
If you mean simply to connect the phone through usb to pc, I cannot do that because MIUI asks everytime if I want to transfer photos, files or just charge with a pop up on screnn (which I obviously cannot do)
iBowToAndroid said:
There is a way to do it, but it costs money
Click to expand...
Click to collapse
what would it be
damndaniel0 said:
If you mean simply to connect the phone through usb to pc, I cannot do that because MIUI asks everytime if I want to transfer photos, files or just charge with a pop up on screnn (which I obviously cannot do)
Click to expand...
Click to collapse
Not in system but in custom recovery (which you do have).
Timmmmaaahh! said:
Not in system but in custom recovery (which you do have).
Click to expand...
Click to collapse
Honestly I did not try, but I don't remember the phone directory showing up in windows file explorer after connecting the phone in recovery mode, I'll try againg when I'm home and I'll let you know
anyway I checked and no, I cannot access phone files
In Recovery mode you should can run
Code:
adb devices
adb pull <LOCATION_OF_DATA_OF_INTEREST> <STORAGE_LOCATION_ON_PC>
xXx yYy said:
In Recovery mode you should can run
Code:
adb devices
adb pull <LOCATION_OF_DATA_OF_INTEREST> <STORAGE_LOCATION_ON_PC>
Click to expand...
Click to collapse
unfortunately the result of this operation is always "pull: building file list... 0 files pulled. 0 files skipped". I tried already to pull form /sdcard, /storage, /data. Am I getting the location wrong?
So I had a pixel 6 pro and unfortunately my wife got mad and threw it against the wall a few times, causing the frame to bend and entire back glass to shatter. The front LCD didn't break, but glue came apart and it separated from the frame.
I had all my 2fa accounts on there, as well as very valuable data that I need to recover.
The phone still powers on, but there's nothing visible on the screen. A local repair shop advised we start by replacing the screen and then work on transferring everything out.
I have a replacement pixel 4a and want to be prepared for when my phone comes back online.
What's the best way to backup my 6 pro and restore on the 4a?
I need everything copied as a whole image, and restored on the 4a. I want to be able to boot up my 4a, open my authenticator app, and have all my accounts listed there.
Someone please tell me this is possible, and if so, please post instructions.
Thank you in advance.
I doubt 1:1 image cloning is possible because encryption is hardware-backed and therefore device-unique. it's not even possible to restore backup on origin device after factory reset since android apps can use keystore in TEE.
side note: you could connect HDMI multiport usb-c otg adapter to TV and mouse so you have access to phone at least
aIecxs said:
I doubt 1:1 image cloning is possible because encryption is hardware-backed and therefore device-unique. it's not even possible to restore backup on origin device after factory reset since android apps can use keystore in TEE.
side note: you could connect HDMI multiport usb-c otg adapter to TV and mouse so you have access to phone at least
Click to expand...
Click to collapse
The HDMI multiport didn't work. Nothing was displayed. I don't know if it's because my phone is badly damaged, or if the pixel 6 doesn't support HDMI out over USB C
I tried this one https://www.amazon.com/dp/B081VBSNRZ/ref=cm_sw_r_apan_i_5NF5RPBKZ97YW4KFW9AX
What are my other options?
the best option would be previously unlocked bootloader, so you can have full access. but you did not unlock bootloader so this is no option for you, because unlocking will factory reset device.
HDMI might require some setting or app installed on device. apps can installed remotely from PC google play with proper google play account. not sure how to start an app though, but guess app can autostart.
at least usb keyboard is working, you could try to navigate blind and enable usb-debugging, this would allow you to use scrcpy. maybe connect headphones or use talkback to get some kind of audio feedback.
of course both methods requires some information from another identical device and need to tested on fully functional pixel 6 pro before..
some (not) useful apps
https://forum.xda-developers.com/t/i-broke-my-screen-and-digitizer.4436261/#post-86791963
https://forum.xda-developers.com/t/broke-the-display-of-my-phone.4424413/#post-86676229
https://forum.xda-developers.com/t/...asily-manage-multiple-android-devices.2707556
Anyone else have suggestions?
AcuraKidd said:
Anyone else have suggestions?
Click to expand...
Click to collapse
This is not a full backup, but it might help you interactively recover some items without replacing the broken screen. Also, assuming this is something you're still looking to solve...
If you have adb debugging enabled, you can try to use https://github.com/Genymobile/scrcpy to interact with your phone over USB from a computer.
If you do not have adb debugging enabled, you can try to enable it via Recovery Mode. The steps to enable Recovery Mode below are from https://www.tenorshare.com/android/how-to-enable-usb-debugging-on-android-with-black-screen.html (I have not tried these steps).
Less:
To enable ADB without a screen:
1. Download the ADB toolkit for your computer and extract its contents to a folder.
ADB toolkit can be found at https://developer.android.com/studio/releases/platform-tools
ADB requires you have USB debugging enabled on your phone.
Since your phone has a black screen, reboot your phone into recovery mode to accomplish this.
Press the Volume Down and Power buttons at the same time to enter recovery mode.
2. Connect your phone to your computer, open a Command Prompt window in the ADB folder, and type the following command.
adb devices
3. You should see your device listed there.
Run the following commands one by one.
adb shell
mount data
mount system
4. Use the following command to pull the persist.sys.usb.config file from your phone to the PC.
adb pull /data/property/persist.sys.usb.config C:\Users\[your-username]\Desktop\
5. Access the persist.sys.usb.config file on your computer with a text editor and edit it to mtp,adb.
6. Run the following command to send the file back to your device.
adb push "C:\Users\[your-username]\Desktop/persist.sys.usb.config" /data/property
7. Download the build.prop file from your phone by using this command.
adb pull /system/build.prop C:\Users\[your-username]\Desktop\
8. Launch the build.prop file in a text editor like NotePad++ on your computer, and add the following code to it.
persist.service.adb.enable=1
persist.service.debuggable=1
persist.sys.usb.config=mtp,adb
9. Save the file and transfer the file back to your device using this command.
adb push "C:\Users\[your-username]\Desktop/build.prop" /system/
10. Reboot your device using the following command.
adb reboot
11. You are all set. Your phone will boot up with USB debugging enabled.