I was looking at a new head unit for my car (for an example: http://www.crutchfield.com/p_13040...EX.html?showAll=N&search=1304000NEX&skipvs=T
That supports the "MHL Standard". Will the slimport adapter work with the Nexus5 and allow it to display on the head unit?
Anyone try something like this yet?
*crickets*
lol bump for same question
want to install appradio 3.
Hello,
Could one of the follow owners describe the pinout of the GA2170 wiring harness.
I can find the pinout of the GA2170B http://www.sbo2.com/p/page/image/GA2170B-28.jpg .. but the GA2170 does not have such diagram online
Sorry if this has been covered already, or if I'm posting in the wrong area.. my brain is melting do to information overload.
Long story short, questions after:
Currently running px3 1gb, 5.1, with bt/wifi issues. I had used a usb-ethernet dongle hooked up to a Asus 330GE portable router in bridge mode. BT Connected and fast network. Woot.
I'm going to be giving my car to my sister, but I feel like the px3/1gb would be dangerously slow. (Keeping android HU for the backup cam I have wired.)
Questions:
1a. There are no bt/wifi chips that can replace (soldering) the current chip to fix the wifi slowdown issue - correct?
1b. Disconnecting the internal module and using USB dongle = same issue - Correct?
1c. Is this because of a USB hub issue I think I read about?
1d. If you have a type2 md725 module, BT does not connect with 8.0 at all, but a type1 can be connected in order to use 8.0, with the wifi-slowdown-when-bt-connected issue persisting - correct?
1e. (bonus) Are there type1 md725 usb dongles?
2a. Do you think a px30 2/16 core board upgrade would be sufficient (not slow as molasses) for basic simultaneous navigation + a2dp/radio/internal player ? (leaving out the assumption that the bt/wifi issue would persist. Talking about system speed wise)
2b. Do you think it would be necessary to bump up to px5 4/32 for $50cad?
3. Why do some of the new DSP eq's show a frequency adjustment low of 25hz, and some 20hz?
4a. What's the deal with these Android GO 8.1/9.0 1gb/16gb units? (I doubt I'd go this route, but just curious.)
4b. Wondering if this 8.1/9.0 GO could be ported to older p3, or p5 2gb units?)
5a. Does the bt-connected-wifi-slowdown issue still remain with these newer p5 units?
5b. Is there a simple way to confirm this other than msging seller for usb hub/wifi/bt specs?
These seem to be the best prices I could find for possible solutions:
*$117ca px30 2/16 Witson coreboard
*$165ca px5 4/32Witson coreboard
*$275cad 4/32 without DSP
*$320cad 4/32 TDA7851 + ST7786
First choice, thinking of upgrading to the px5 4/32
Would like to save 50$ if possible by using a px30 2/16
Would like to save all the monies by somehow convincing humans greater than myself to port 8.1/9.0 GO over? (assuming this would be quick enough)
*!HeadEsplode!*
When I do get this sorted (new(to me) vehicle acquired, current vehicle to sister,) I will most likey be going the 4/32 px5 DSP route, or possibly px6. (or Intel?) (Headexplodeagain!)
Hoping someone out there can steer me right ...
PX6 upgrade
I have the same set of questions, but also would like to add PX6 board in the list. Does anyone tried upgrading PX3 to PX6 on MTCD board?
Head Uni: A-MEDIA Auto (1024x600 W)
MCU version：
MTCD_JY_V1.90_2
Sep 26 2016 13:56:13
Android 5.1.1
StingerRUS2 said:
I have the same set of questions, but also would like to add PX6 board in the list. Does anyone tried upgrading PX3 to PX6 on MTCD board?
Head Uni: A-MEDIA Auto (1024x600 W)
MCU version：
MTCD_JY_V1.90_2
Sep 26 2016 13:56:13
Android 5.1.1
Click to expand...
Click to collapse
I'm not sure, but I found this on another thread:
" yes, you can use the updates listed as PX6 (as they show PX5 once you download them). "
linking to https://forum.xda-developers.com/an...asaita-mcu-updates-rockchip-px5-octa-t3575155
I'm thinking yes. Have you seen any px6 coreboards for sale yet? Maybe there will be a group buy ..
StingerRUS2 said:
I have the same set of questions, but also would like to add PX6 board in the list. Does anyone tried upgrading PX3 to PX6 on MTCD board?
Head Uni: A-MEDIA Auto (1024x600 W)
MCU version：
MTCD_JY_V1.90_2
Sep 26 2016 13:56:13
Android 5.1.1
Click to expand...
Click to collapse
This guy says yes
"If you have any MTCD or MTCE unit you can upgrade to an RK3368/PX5 SoM, or an RK3399/PX6 SoM. " - typos1
https://forum.xda-developers.com/showpost.php?p=78564585&postcount=686
ftwk said:
I'm not sure, but I found this on another thread:
" yes, you can use the updates listed as PX6 (as they show PX5 once you download them). "
linking to https://forum.xda-developers.com/an...asaita-mcu-updates-rockchip-px5-octa-t3575155
I'm thinking yes. Have you seen any px6 coreboards for sale yet? Maybe there will be a group buy ..
Click to expand...
Click to collapse
https://magnitolog.ru/glavnaya/magazin/процессорная-плата-rockchip-htc-px30-rev05-ram-2-gb-66-detail
No stock...
Sent from my Pixel 3 using Tapatalk
Just to tag on and answer some of OP's questions as I'm in a similar situation:
1.d - You're correct (from all the reading I've done too). There's type 1 and type 2 MD725, with type 2 not working with android 8.0 due to driver issues.
1.e - There are usb dongles with Type 1: Comfast WU725B. This apparently solves people's issues.
2.a Although the PX30 should be better in terms of speed, I'm pretty sure you will still get a bit of lag with navigation (generally loading things up) but otherwise ok once running as long as there isn't too much running in the background. That is just an assumption as I don't have any experience with a PX30...but I do own a PX3 with 2GB RAM which is meant to be slightly worse than the PX30.
2.b. You'll be better off getting the PX5 if you're doing a coreboard upgrade anyway...I regret to not going the PX5 route from the beginning.
Now a question for everyone else:
I'm looking to upgrade my PX3 (2GB/32GB) with a PX5 coreboard. It appears only Rev8 PX5 Coreboards are available now which come with android 8.0 and the warning about Bluetooth and wireless potentially not working (which we know about MD725 type 1 and 2).
However my MTCE unit has Bluetooth module SD968 (with a separate wireless card) and I can't find any mention if I will have any problems if I upgrade the coreboard.
Does anyone know if the SD968 works fine with Android 8.0 PX5 coreboard?
fl4r3 said:
Just to tag on and answer some of OP's questions as I'm in a similar situation:
1.d - You're correct (from all the reading I've done too). There's type 1 and type 2 MD725, with type 2 not working with android 8.0 due to driver issues.
1.e - There are usb dongles with Type 1: Comfast WU725B. This apparently solves people's issues.
2.a Although the PX30 should be better in terms of speed, I'm pretty sure you will still get a bit of lag with navigation (generally loading things up) but otherwise ok once running as long as there isn't too much running in the background. That is just an assumption as I don't have any experience with a PX30...but I do own a PX3 with 2GB RAM which is meant to be slightly worse than the PX30.
2.b. You'll be better off getting the PX5 if you're doing a coreboard upgrade anyway...I regret to not going the PX5 route from the beginning.
Now a question for everyone else:
I'm looking to upgrade my PX3 (2GB/32GB) with a PX5 coreboard. It appears only Rev8 PX5 Coreboards are available now which come with android 8.0 and the warning about Bluetooth and wireless potentially not working (which we know about MD725 type 1 and 2).
However my MTCE unit has Bluetooth module SD968 (with a separate wireless card) and I can't find any mention if I will have any problems if I upgrade the coreboard.
Does anyone know if the SD968 works fine with Android 8.0 PX5 coreboard?
Click to expand...
Click to collapse
Yes it does. That is the combo that i'm running in one of my radios.
Perfect! Thanks for confirming that. Guess there's nothing stopping me now, unless a PX6 board magically appears lol.
What do so have?
Hi there,
Sorry to open an old thread.
I have been reading up for ages but can't identify what MCU I have, is anyone able to tell me from the pictures or do I need to physically take it out and check?
Thanks.
anybody know where i can buy px5 or px6 core board? xtrons want to sell me the px5 4/32 for 150$! it is too expensive!
Hi, I have a px3 board with mtcd software and want to upgrade to px5. My board has a md725 Bluetooth chip installed so could anyone advise me on a suitable upgrade path as the 1gb of ram is killing me ha many thanks!
Hi, I have a px3 board with mtcd software and want to upgrade to px5. My board has a md725 Bluetooth chip installed so could anyone advise me on a suitable upgrade path as the 1gb of ram is killing me ha many thanks!
Hi, I have a px3 with md725 bluetooth on mtcd software. I would like to upgrade to a px5 board so could anyone point me to a listing which I can purchase from that will work? I dont want to lose any functionality of the Bluetooth/WiFi so I'm not bothered if it's running on android 8 or below or 9 if possible. Also should I upgrade to mtce first or after upgrade or does it not matter? Many thanks
Hi, I have a px3 with md725 bluetooth on mtcd software. I would like to upgrade to a px5 board so could anyone point me to a listing which I can purchase from that will work? I dont want to lose any functionality of the Bluetooth/WiFi so I'm not bothered if it's running on android 8 or below or 9 if possible. Also should I upgrade to mtce first or after upgrade or does it not matter? Many thanks
can someone explain to me how to use the hdmi out on dasaita px6
Hi,
Is generic dab+ adapter working on Joying Android 8.1 Intel Airmont SC9853i?
Im thinking of buying xtrons or some other usb adapter...
Thanks
pajo985 said:
Hi,
Is generic dab+ adapter working on Joying Android 8.1 Intel Airmont SC9853i?
Im thinking of buying xtrons or some other usb adapter...
Thanks
Click to expand...
Click to collapse
don't see any problem for that, simply be sure that the dab software woks with the desired dab hardware !
pajo985 said:
Hi,
Is generic dab+ adapter working on Joying Android 8.1 Intel Airmont SC9853i?
Im thinking of buying xtrons or some other usb adapter...
Click to expand...
Click to collapse
Xtrons is OK. Read post #1 of this thread about the DAB-Z app and compatibility.