Database Info

[Q] Help Un-bricking Sensation 4G?

So I checked the existing pages about bricked Sensations but I didn't
see any predicaments that were quite this bad let alone a fix. Anyways;
Was updating to newest firmware 3.24 because I was getting ready to flash a
new ICS rom. Updated fine in Hboot, and then I somehow managed to reboot before I could get into clockwork recovery mod. Got caught in a boot-loop so I
pulled the battery to try to get back into fastboot and it wouldn't even turn on.
So I pulled the battery again, held the power button to drain any power and put the battery back in and tried it again. It will not charge, the led will not turn on, and it gets a black screen with the back-light on. Can not get into anything, kinda looking like the internal memory was wiped somehow.
So are there any fixes? Or am I screwed? If so if I call tmobile will they replace it (in the event that everything was wiped)? Any help appreciated!

Wanderer_Zero said:
So I checked the existing pages about bricked Sensations but I didn't
see any predicaments that were quite this bad let alone a fix. Anyways;
Was updating to newest firmware 3.24 because I was getting ready to flash a
new ICS rom. Updated fine in Hboot, and then I somehow managed to reboot before I could get into clockwork recovery mod. Got caught in a boot-loop so I
pulled the battery to try to get back into fastboot and it wouldn't even turn on.
So I pulled the battery again, held the power button to drain any power and put the battery back in and tried it again. It will not charge, the led will not turn on, and it gets a black screen with the back-light on. Can not get into anything, kinda looking like the internal memory was wiped somehow.
So are there any fixes? Or am I screwed? If so if I call tmobile will they replace it (in the event that everything was wiped)? Any help appreciated!
Click to expand...
Click to collapse
Do you have ADB installed? Plug in the phone and power on, then see of your PC can see the phone by going to a command prompt and running
Code:
adb devices

tried it, doesnt show up

Wanderer_Zero said:
tried it, doesnt show up
Click to expand...
Click to collapse
I'm just looking at some stuff about QPST, which might help you - I'll post back once I understand it
Have you tried downloading a stock RUU and running that?

wmoore said:
I'm just looking at some stuff about QPST, which might help you - I'll post back once I understand it
Have you tried downloading a stock RUU and running that?
Click to expand...
Click to collapse
Hi wmoore,
i am currently in a position of figured out the information about this program, see my other post...
I am just trying to find someone who might help me with the project
GreetZ

Have a look at this. Follow steps 3 and 4 and tell me if you can see your device.
---------- Post added at 08:30 PM ---------- Previous post was at 08:29 PM ----------
Da_Loony said:
Hi wmoore,
i am currently in a position of figured out the information about this program, see my other post...
I am just trying to find someone who might help me with the project
GreetZ
Click to expand...
Click to collapse
Not sure how much help I would be I'm just trying to read up on QPST now. I have heard of it but never looked into any detail.

cant do that; when i try to boot my phone, all that happens is the backlight turns on and im stuck with a black screen. cant boot, cant get into fastboot/bootloader/cwm or anything

Wanderer_Zero said:
cant do that; when i try to boot my phone, all that happens is the backlight turns on and im stuck with a black screen. cant boot, cant get into fastboot/bootloader/cwm or anything
Click to expand...
Click to collapse
Well, i am in the same situation with my sensation, it doesn't power on and when connected to the pc it shows up as QHSUSB_DLOAD and the driver was not found auto by windows
i'm going to provide the links to the program and the driver in the thread i started to get the QCN File...
The standard answer provided here in that situation is that your phone is bricked and you need to send it to HTC for warranty reparation...I am going to try to get a DIY method to reflash your phone from scratch (as now it's waiting for a ROM to be download (Qualcomm High Speed USB DownLOAD mode)
---------- Post added at 12:02 PM ---------- Previous post was at 11:42 AM ----------
wmoore said:
Have a look at this. Follow steps 3 and 4 and tell me if you can see your device.
---------- Post added at 08:30 PM ---------- Previous post was at 08:29 PM ----------
Not sure how much help I would be I'm just trying to read up on QPST now. I have heard of it but never looked into any detail.
Click to expand...
Click to collapse
Well...
Everything is explained in http://forum.xda-developers.com/showthread.php?t=1468791
How much help can you be? simple, i need a dump of the rom which runs on your Sensation, but not an .img file, but a .qcn file, QPST provides that feature, but it hardcodes you EMEI and serial into it, therefor i need to get all the info about your phone, all numbers you can provide that are listed on the box in order to get searching for those variables in that file which is dumped...
When found i can change them into my vars, to try and flash the phone back to life... i geuss it'll be a work off about a week to get everything found in a 400MB file or so

Da_Loony said:
Well, i am in the same situation with my sensation, it doesn't power on and when connected to the pc it shows up as QHSUSB_DLOAD and the driver was not found auto by windows
i'm going to provide the links to the program and the driver in the thread i started to get the QCN File...
The standard answer provided here in that situation is that your phone is bricked and you need to send it to HTC for warranty reparation...I am going to try to get a DIY method to reflash your phone from scratch (as now it's waiting for a ROM to be download (Qualcomm High Speed USB DownLOAD mode)
---------- Post added at 12:02 PM ---------- Previous post was at 11:42 AM ----------
Well...
Everything is explained in http://forum.xda-developers.com/showthread.php?t=1468791
How much help can you be? simple, i need a dump of the rom which runs on your Sensation, but not an .img file, but a .qcn file, QPST provides that feature, but it hardcodes you EMEI and serial into it, therefor i need to get all the info about your phone, all numbers you can provide that are listed on the box in order to get searching for those variables in that file which is dumped...
When found i can change them into my vars, to try and flash the phone back to life... i geuss it'll be a work off about a week to get everything found in a 400MB file or so
Click to expand...
Click to collapse
OK well I already have QPST and the QHSUSB drivers downloaded but QPST cannot see my phone. I found something on an LG forum explaining how to get the COM port number from Device Manager but my phone doesn't show up the same way.
Can you tell me how to find my COM port?

wmoore said:
OK well I already have QPST and the QHSUSB drivers downloaded but QPST cannot see my phone. I found something on an LG forum explaining how to get the COM port number from Device Manager but my phone doesn't show up the same way.
Can you tell me how to find my COM port?
Click to expand...
Click to collapse
Yep
Windows 7?
Open your Control Panel from your start menu and put it on classic view, in order to see the device manager link, open this.
There you will see Ports (COM & LPT)
Unfold this and you will see your device there with a (COMx) behind it
in the QPST configurator you will have a tab with the name: Ports
click this
on the right bottom there is a button: Add New Port
click this, a dialog will open where you can see your ports, click the port which is of your phone, if not seen, just type COMx (x being the number stated in the device manager)
And press OK
As from now you will be able to see your phone on the first tab normally seen
now go to the menu "Start Clients"
SOFTWARE DOWNLOAD
If you see that the port is not correct on top, click the Browse next to it in order to choose the correct port, you'll see it will detect your phone then...
Goto the Backup tab and click browse, give the file a place and name, press start...
Then wait i guess, i am not in the possition to know how long it would take...
Now you have the QCN file made as i need in my post
This is a hexadecimal dump of your phone in Quallcomm Bundle Numeric format, with that we can start figuring out, how to get your serial number, emei etc out, to infuse our own to get our phone back up and running by using the restore function of the QPST program
Clear enough? :s
---------- Post added at 12:33 PM ---------- Previous post was at 12:30 PM ----------
It might also be that due to the fact that your phone is actually a still working exemplar that you need to follow the guide here: http://forum.xda-developers.com/showthread.php?t=1180211 in order to get your phone connected in QPST

Da_Loony said:
Yep
Windows 7?
Open your Control Panel from your start menu and put it on classic view, in order to see the device manager link, open this.
There you will see Ports (COM & LPT) <SNIP>
Click to expand...
Click to collapse
This is where I come unstuck. I don't have Ports in my Device Manager. I'm on a laptop that doesn't have serial or parallel ports, so that is probably why.

wmoore said:
This is where I come unstuck. I don't have Ports in my Device Manager. I'm on a laptop that doesn't have serial or parallel ports, so that is probably why.
Click to expand...
Click to collapse
Perhaps they are hidden?
Which windows are you using?

Da_Loony said:
Perhaps they are hidden?
Which windows are you using?
Click to expand...
Click to collapse
Win7 Ultimate x64. I checked hidden devices but they are not there either.

wmoore said:
Win7 Ultimate x64. I checked hidden devices but they are not there either.
Click to expand...
Click to collapse
Try to follow the manual i've placed online in my thread step by step: http://forum.xda-developers.com/showthread.php?t=1468791
guess your phone is not in diagnostics mode and therefor making not the right type of connection via USB

Da_Loony said:
Try to follow the manual i've placed online in my thread step by step: http://forum.xda-developers.com/showthread.php?t=1468791
guess your phone is not in diagnostics mode and therefor making not the right type of connection via USB
Click to expand...
Click to collapse
I've just realised why this isn't working for me. I'm using an AOSP ROM, so no HTC diags

wmoore said:
I've just realised why this isn't working for me. I'm using an AOSP ROM, so no HTC diags
Click to expand...
Click to collapse
No prob it was nice to know you would have helped me out if possible... up to the next one hehe

Da_Loony said:
No prob it was nice to know you would have helped me out if possible... up to the next one hehe
Click to expand...
Click to collapse
I've just taken a backup and am flashing ARHD 6.0.2 (because I had it downloaded already)
Gimme 20 minutes.

wmoore said:
I've just taken a backup and am flashing ARHD 6.0.2 (because I had it downloaded already)
Gimme 20 minutes.
Click to expand...
Click to collapse
Many thanks, i'm gonna PM you with my info (as promissed in my thread)

So I've gone back to ENG HBOOT 1.17 and Telstra stock ROM, Clockwork Recovery 5.0.0.8 and rooted. I have USB debugging on and am in diagnostic mode but I still don't get HTC Diag device or anything like it in Device Manager. I've shown hidden devices in there too.
The only phone related item I have is Portable Device, when expanded it says D:\ (which is my SD card drive in the phone). I tried changing USB mode from charge to disk to sync and every other option but still don't see the device in Device Manager.
Not sure what else I can do here .... Plus it's pretty late and I want to restore my phone before bed. If you can think if anything I've done wrong or anything I can try differently, please let me know and I'll try tomorrow.

No problem man, i know there is a time difference between Belgium and Australia
Have you checked that the phone is in charge mode and not in disk drive mode?
GreetZ
wmoore said:
So I've gone back to ENG HBOOT 1.17 and Telstra stock ROM, Clockwork Recovery 5.0.0.8 and rooted. I have USB debugging on and am in diagnostic mode but I still don't get HTC Diag device or anything like it in Device Manager. I've shown hidden devices in there too.
The only phone related item I have is Portable Device, when expanded it says D:\ (which is my SD card drive in the phone). I tried changing USB mode from charge to disk to sync and every other option but still don't see the device in Device Manager.
Not sure what else I can do here .... Plus it's pretty late and I want to restore my phone before bed. If you can think if anything I've done wrong or anything I can try differently, please let me know and I'll try tomorrow.
Click to expand...
Click to collapse

Hard Bricked Moto G 2013 Help/Solutions

Nothing new about , MBM 5.0 ? , Image Factory ? sorry one more topic

ST4NL3//Y said:
Nothing new about , MBM 5.0 ? , Image Factory ? sorry one more topic
Click to expand...
Click to collapse
till now is no news about that, how? when? where? what? i dont know

ST4NL3//Y said:
Nothing new about , MBM 5.0 ? , Image Factory ? sorry one more topic
Click to expand...
Click to collapse
i'm waiting too :crying:
maybe other solution?(
can someone smart can help us?
Can pay someone?

MadL1fe said:
i'm waiting too :crying:
maybe other solution?(
can someone smart can help us?
Can pay someone?
Click to expand...
Click to collapse
bring your phone to services center, your problem will solved but you must pay it

I already tried everything, but it looks like we will have to wait even. there is no any news about a tool I'm sad without my moto G

Sandivisi said:
bring your phone to services center, your problem will solved but you must pay it
Click to expand...
Click to collapse
in my country no motorola service centers

many of us have lost the guarantee of motorola

ST4NL3//Y said:
many of us have lost the guarantee of motorola
Click to expand...
Click to collapse
I will pay what I can, if someone will help restore .Here is a lot of clever people ... that no one can help?

You say hardbricked, you mean the phone doesnt boot right?
If you connect to pc, installs an driver named HSusb for qualcomm s1 emergency boot?
Normal it must do that.If not, press vol keys and put usb in.
Normaly you cant brick qualcomm emergency mode. If you get this driver installed, write me a pn. i can flash it back to normal recovery.

konsolen said:
You say hardbricked, you mean the phone doesnt boot right?
If you connect to pc, installs an driver named HSusb for qualcomm s1 emergency boot?
Normal it must do that.If not, press vol keys and put usb in.
Normaly you cant brick qualcomm emergency mode. If you get this driver installed, write me a pn. i can flash it back to normal recovery.
Click to expand...
Click to collapse
no man, the phone doesnt boot into fastboot
and we need blankflash/mbm-ci for new bootloader lollipop to make it work

correct need of blankflash compatible with 5.0

i dont need fastboot.
i upload with a serial line in raw format.

konsolen said:
i dont need fastboot.
i upload with a serial line in raw format.
Click to expand...
Click to collapse
how?
my phone dead after downgrade to 4.4.3 then upgrade to 4.4.4 from android 5.0

Sandivisi said:
how?
my phone dead after downgrade to 4.4.3 then upgrade to 4.4.4 from android 5.0
Click to expand...
Click to collapse
me was exactly the same

Then go to the store.
i will give you my help and you want inform me about updates.
i read that, but you shredder your masterboot register in nandflash.
there is no android. this is the lowest level of a device. name it layer 0.
you crashed the register where the cpu looks what he must do, to start the first sequence.

konsolen said:
You say hardbricked, you mean the phone doesnt boot right?
If you connect to pc, installs an driver named HSusb for qualcomm s1 emergency boot?
Normal it must do that.If not, press vol keys and put usb in.
Normaly you cant brick qualcomm emergency mode. If you get this driver installed, write me a pn. i can flash it back to normal recovery.
Click to expand...
Click to collapse
come on, help us
---------- Post added at 10:54 PM ---------- Previous post was at 10:47 PM ----------
konsolen said:
Then go to the store.
i will give you my help and you want inform me about updates.
i read that, but you shredder your masterboot register in nandflash.
there is no android. this is the lowest level of a device. name it layer 0.
you crashed the register where the cpu looks what he must do, to start the first sequence.
Click to expand...
Click to collapse
i dont understand what you mean, so what should I do

ok.the qualcomm driver is installed right?
then load the teamviewer.exe app.
i look for the right snapdragon 400 mbr and connect then to your pc.

konsolen said:
ok.the qualcomm driver is installed right?
then load the teamviewer.exe app.
i look for the right snapdragon 400 mbr and connect then to your pc.
Click to expand...
Click to collapse
yes, it already installed
and for what teamviewer?

i must connect to flash.

same problem with me .I flashed stock rom to downgrade to 4.4.3 from rooted stock lollipop OS because of messing up build.prop file.After that,I have installed OTA update to 4.4.4,then the problem starts no bootloader,no boot,no fastboot,no adb,no recovery and except qhsusb_bulk when connected to PC.After 2 days ,its now showing sometimes as usb input device ,with LED light blinking.Not sure if there is solutuion for this.pls help if anyone found the solution

Samsung Galaxy Tab 2 10.1 Help!!

Hi everyone, I am a new person in the forums, so please understand if I'm not good at some stuff and if I'm posting this in the wrong place
Well, story is that I found my old Galaxy Tab 2 in my basement after 3 years, and I got it to turn on (no factory cable, 1€ chinese cable). Android version is 4.0.3.
Found a couple of roms in the forums for 6.0, and yes, I've done it before on my phones.
Computer cannot recognize the tab, only says "Unrecognized device", even though I've tried every driver there is to it. Tried kies, no help. Tried odin, no help.
Neither of those detect the tab either, so I rooted it from the tab itself with KingRoot.
Now the tab is rooted, and I tried to flash TWRP to install 6.0.
It says that the recovery is flashed, but when I try to reboot to recovery, it only restarts, with nothing.
It goes into download mode just perfectly, but when connected to the pc, it still doesn't detect it.
I do not have money to buy a new tablet, so I would really like some advice.
Thanks!

hello
go in download mod ( power & vol+ )
go back to origin
use cfautoroot (all needed in it odin + drivers + cfautoroot)
use a new cable
after that install twrp, os ( first cm12.1 )
regards

Hi, will try!

Don't set auto reboot in Odin.
Once TWRP is flashed wait 1 minute and unplug the tab.
Now directly boot into TWRP, else stock recovery get restored on boot.
You should update over OTA to 4.1 or 4.2 if available first, else you'll have to flash a newer bootloader using Odin to avoid graphics glitches at boot.

Android-Andi said:
Don't set auto reboot in Odin.
Once TWRP is flashed wait 1 minute and unplug the tab.
Now directly boot into TWRP, else stock recovery get restored on boot.
You should update over OTA to 4.1 or 4.2 if available first, else you'll have to flash a newer bootloader using Odin to avoid graphics glitches at boot.
Click to expand...
Click to collapse
Hi, thanks! Got it working!
It was a very good idea to ask xda for help

Can you tell me how you did it? Where to get origin? I have the same problem - please help.

dionex2k said:
Can you tell me how you did it? Where to get origin? I have the same problem - please help.
Click to expand...
Click to collapse
Read above, lol, he quoted it too

I did.... my computer does not even recognize my tab - I tried 3 different cables and 2 different computers.

Use the driver from here http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows

Android-Andi said:
Use the driver from here http://developer.samsung.com/galaxy/others/android-usb-driver-for-windows
Click to expand...
Click to collapse
I installed the drivers from the link you provided - my laptop still does not recognize my tablet... any other suggestions?

dionex2k said:
I installed the drivers from the link you provided - my laptop still does not recognize my tablet... any other suggestions?
Click to expand...
Click to collapse
Tired a different cable? Different usb port?

dionex2k said:
I installed the drivers from the link you provided - my laptop still does not recognize my tablet... any other suggestions?
Click to expand...
Click to collapse
I have heard about a tool called "Forget Windows Use Linux (FWUL)" but I have not tried it. Maybe give it a shot

hello
cfautoroute gives odin, drivers, ...
regards

dionex2k said:
I installed the drivers from the link you provided - my laptop still does not recognize my tablet... any other suggestions?
Click to expand...
Click to collapse
Is your cable a data cable or just a charging cable?

UnavailableSurm said:
Is your cable a data cable or just a charging cable?
Click to expand...
Click to collapse
Yes I tried 3 cables they are for data and charging
---------- Post added at 06:55 PM ---------- Previous post was at 06:53 PM ----------
validatus said:
hello
cfautoroute gives odin, drivers, ...
regards
Click to expand...
Click to collapse
I tried that - did not work.
---------- Post added at 06:55 PM ---------- Previous post was at 06:55 PM ----------
Can someone try and help me via teamviewer? It would make me happy because I really want to use this damn tablet again.

Vodafone VFD 300 Free Network Unlock Done! 10000% Working!

How to unlock Vodafone vfd300 any network any carrier?
Follow the instructions.
Download:
https://mega.nz/#F!MpM2QRYT!j8GtDwqyhU7TsunOZxadmg
Click on Flash_tool.exe
- Select "scatter-Loading" and search MT6580_Android_scatter.txt in ROM
- Wait file to be added into Flash Tool
- Select "Download Only"
- Turn off your phone, remove the battery and replace it after some seconds (and don't turn on the phone).
- Press “Download” button to start
- and connect your phone into the computer via USB data cable.
- The process will start and a red progress bar will appear after color purple, yellow.
- And green circles display
-Start recovery and wipe data and cache.
-Reboot system
- Finish !
-ENJOY!!!

Hi there Mercyless,
I tried your instructions step by step but I'm getting this error message when I load the scatter file:
Partition[frp] shoult NOT set "is_download" to true in scatter file
Please check
What can I do? Thanks.

Bogdanux said:
Hi there Mercyless,
I tried your instructions step by step but I'm getting this error message when I load the scatter file:
Partition[frp] shoult NOT set "is_download" to true in scatter file
Please check
What can I do? Thanks.
Click to expand...
Click to collapse
No problem my friend!
Just use this sp flashtool:
https://mega.nz/#F!0pU01Y4C!shO88mJ-svGJ8tni_5DmLA
:good:

Hi again,
I tried your version but I get the following error:
BROM ERROR : S_BROM_CMD_STARTCMD_FAIL (2005)
Tried the general fixes of this error but no help. Also, I used the latest SP Flash Tool from the official website and another ROM and it worked (only without battery).
I'll try on a different computer with your downloads to see if I get the same result.

Bogdanux said:
Hi again,
I tried your version but I get the following error:
BROM ERROR : S_BROM_CMD_STARTCMD_FAIL (2005)
Tried the general fixes of this error but no help. Also, I used the latest SP Flash Tool from the official website and another ROM and it worked (only without battery).
I'll try on a different computer with your downloads to see if I get the same result.
Click to expand...
Click to collapse
This means that the device will try to turn it on, not start flash mode.
First, charge the battery.
Do not use the latest flashtoolt, use what i've shown, the older version!!
Reinstall the drivers, use another cable.
The firmware is working, I've used it many times! :good:

Feedback please...
Hi there,
I want to root also, can anyone give a feedback on theses procedures. Are they working?
Thanks

Scam
File won't even download, gets to 51% then stops, tried 3 times now

I'm trying to download the file. After using i will give feedback.

NoName4me82 said:
File won't even download, gets to 51% then stops, tried 3 times now
Click to expand...
Click to collapse
SCAM???
Do not talk stupid things!!
If you can not download a simple file, do not come here!
Downloading works, files are good!
Do not lie to others, ugly thing!

Usb debugging????
I flashed my vfd300 with the stock rom using spflash but i made a rookie mistake by not turning debugging on resulting in phone stuck at spinning circle, will this flash withouy debugging, or do you know any way i can enable it using adb or fastboot??
cheers

jonny5alen said:
I flashed my vfd300 with the stock rom using spflash but i made a rookie mistake by not turning debugging on resulting in phone stuck at spinning circle, will this flash withouy debugging, or do you know any way i can enable it using adb or fastboot??
cheers
Click to expand...
Click to collapse
The first departure is 15-20 minutes, just wait.

Waited much longer,
Mercyless said:
The first departure is 15-20 minutes, just wait.
Click to expand...
Click to collapse
I left it all night and it never got past the circle, ive just managed to flash again using a difarent rom so ill see if this one works,
im stiull waiting for your one to download, when its finidhed will it flash with out usb debugging enabled ?

Hello,my device is already rooted but it is network locked. If i flash this scatter file,will i lose root after flashing?

Trace.Oneil said:
Hello,my device is already rooted but it is network locked. If i flash this scatter file,will i lose root after flashing?
Click to expand...
Click to collapse
Hi Friend! Root will not be available.

jonny5alen said:
I left it all night and it never got past the circle, ive just managed to flash again using a difarent rom so ill see if this one works,
im stiull waiting for your one to download, when its finidhed will it flash with out usb debugging enabled ?
Click to expand...
Click to collapse
I'm Hungarian, I do not understand the question.
Please write more clearly.

Mercyless said:
Hi Friend! Root will not be available.
Click to expand...
Click to collapse
So if i flash this i will lose root?

Flashed it?
Hi merciless,
I finally managed to flash our rom just now but its still just stopping at a spinning circle, Any Ideas mate
---------- Post added at 04:20 PM ---------- Previous post was at 04:17 PM ----------
Mercyless said:
I'm Hungarian, I do not understand the question.
Please write more clearly.
Click to expand...
Click to collapse
Sorry,
what i meant was that i managed to flash a stock rom but it never actually booted up, it just gets to a spinning disc
but originally i never enabled usb debugging so i fear that is where the issue is do you know of anyway to enable usb-debugging via adb\fastboot?

jonny5alen said:
Hi merciless,
I finally managed to flash our rom just now but its still just stopping at a spinning circle, Any Ideas mate
---------- Post added at 04:20 PM ---------- Previous post was at 04:17 PM ----------
Sorry,
what i meant was that i managed to flash a stock rom but it never actually booted up, it just gets to a spinning disc
but originally i never enabled usb debugging so i fear that is where the issue is do you know of anyway to enable usb-debugging via adb\fastboot?
Click to expand...
Click to collapse
Unfortunately I do not know how to work this way with adb / fastboot.
I did not have to use it yet.
If you do not start the system to do a hard reset, it will surely be good afterwards.
After the hard reset, the first start is 15-20 minutes, just wait patiently.
I will also make a video about the installation, I hope it will help.

Trace.Oneil said:
So if i flash this i will lose root?
Click to expand...
Click to collapse
Yes, she needs to re-root.

vfd 300
I found another ROM - [MT6580_S00_EMMC_MRA58K__6.0_VFD 300_Vodafone_356774071726533_08_19_2016_09_02_53
and after flashing it with this one, everything appeared fine. The language was Vietnamese or somemthing and the region from Australia & East Asia, but still I managed to change it, root the phone and setup my stuff... with only one big problem, when I insert my SIM card, it asks for a network lock [NP] and says I have 99 attempts left.
---------- Post added at 07:32 AM ---------- Previous post was at 07:23 AM ----------
i have tried but my phone keep disconecting after 2 second and procces fails, but when am using this ROM --MT6580_S00_EMMC_MRA58K__6.0_VFD 300_Vodafone_356774071726533_08_19_2016_09_02_53 it is flashing well but sim is locked .......i have tried bettery trick the phone dont disconect but nothing is happening.
HELP ME PLEASE!!!!!!!!!

Samsung Galaxy S8+ Hard Bricked. Only Upload Mode!! How to Enter Download Mode???

Ok so I went to flash twrp recovery onto my phone and something went wrong while using oden... My usb debugging is turned on and OEM Unlocked. Now my phone screen stays completely black. Its caught in a bootloop and No buttons work to bring it back into download mode, Only Upload mode works.. But Odin will not flash anything to my phone in Upload mode. It changes my samsung usb drivers to msm upload or modem drivers. I have been at this for weeks trying to get my s8+ to attach to my computer again using ADB, ODIN, SD CARD, AND EVEN THAT JIG Thing to force it into download mode but TO NO AVAIL.. I Have to some how get back into download mode but no button combinations will work.. It seems to bootloop on me before it reaches those commands. The bootloader is obviously gone to a certain degree since upload mode still works.. Is there any way to use Odin in upload mode? Or is there any other way I can reflash stock rom to fix this issue? I have no recovery, no safe mode, no download mode?? My phone is basically a paper weight right now.. When I know All my stuff is still on there. This S8+ Phone has put up a good fight with me on my pc But Im not one to loose. I love a good challange.. Any suggestions. I thought ADB Was my best bet but with no connect I cant do any thing. I cant' get Adb to find my device. Oh even tryed older versions of odin with low level quallcom drivers and that didn't work either. Odin will read a com port to my device but i'm in the wrong mode (Upload Mode) and Odin cant establish a connection. When in Upload Mode its the hellish one as xda deveopers have said before..
S8+ phone is Model Number SM-G950U
Witch I believe has now been upgraded to SM-G955U OR F.. But I have the original stock rom still for SM-G950U if only I can get into some kind of Download Mode.
Ive even sat watching odin as I push every single button combination watching the ports appear and dissapear as it reboots trying to find some kind of way to download to the phone... But no luck..
UNKNOWN ERROR
DDR VENDER : UNKNOWN
SOC_HW_REVISION : 2.1
SKIP PRINT_SUMMERY_TO_LCD
GENERATING SUMMERY........
GENERAL INFO
DDR INFO
DCVS INFO
RPM INFO
RECOVERED FROM AN EXCEPTION
DONE
Then if I hold the up button for a few seconds I get this underneath
SYNCHRONOUS EXCEPTION
LR : 0x0000000085e36d98
sp : 0x000000001407bbb0
pc : 0x0000000085e36df8
Not sure what that means or how to look up those codes but I know its all bad.. If anyone can think of any other way to connect my phone to reflash stock rom to fix Please let me know any theories or suggestions you may have for me to try... Thank You...

Gkeplar said:
Ok so I went to flash twrp recovery onto my phone and something went wrong while using oden... My usb debugging is turned on and OEM Unlocked. Now my phone screen stays completely black. Its caught in a bootloop and No buttons work to bring it back into download mode, Only Upload mode works.. But Odin will not flash anything to my phone in Upload mode. It changes my samsung usb drivers to msm upload or modem drivers. I have been at this for weeks trying to get my s8+ to attach to my computer again using ADB, ODIN, SD CARD, AND EVEN THAT JIG Thing to force it into download mode but TO NO AVAIL.. I Have to some how get back into download mode but no button combinations will work.. It seems to bootloop on me before it reaches those commands. The bootloader is obviously gone to a certain degree since upload mode still works.. Is there any way to use Odin in upload mode? Or is there any other way I can reflash stock rom to fix this issue? I have no recovery, no safe mode, no download mode?? My phone is basically a paper weight right now.. When I know All my stuff is still on there. This S8+ Phone has put up a good fight with me on my pc But Im not one to loose. I love a good challange.. Any suggestions. I thought ADB Was my best bet but with no connect I cant do any thing. I cant' get Adb to find my device. Oh even tryed older versions of odin with low level quallcom drivers and that didn't work either. Odin will read a com port to my device but i'm in the wrong mode (Upload Mode) and Odin cant establish a connection. When in Upload Mode its the hellish one as xda deveopers have said before..
S8+ phone is Model Number SM-G950U
Witch I believe has now been upgraded to SM-G955U OR F.. But I have the original stock rom still for SM-G950U if only I can get into some kind of Download Mode.
Ive even sat watching odin as I push every single button combination watching the ports appear and dissapear as it reboots trying to find some kind of way to download to the phone... But no luck..
UNKNOWN ERROR
DDR VENDER : UNKNOWN
SOC_HW_REVISION : 2.1
SKIP PRINT_SUMMERY_TO_LCD
GENERATING SUMMERY........
GENERAL INFO
DDR INFO
DCVS INFO
RPM INFO
RECOVERED FROM AN EXCEPTION
DONE
Then if I hold the up button for a few seconds I get this underneath
SYNCHRONOUS EXCEPTION
LR : 0x0000000085e36d98
sp : 0x000000001407bbb0
pc : 0x0000000085e36df8
Not sure what that means or how to look up those codes but I know its all bad.. If anyone can think of any other way to connect my phone to reflash stock rom to fix Please let me know any theories or suggestions you may have for me to try... Thank You...
Click to expand...
Click to collapse
You have a 950 u locked bootloader. First mistake trying to flash twrp. Only option you have is finding the revision bootloader you where on edl files and pinout to 9008 edl mode. There as of last known no fix other than for upload mode only.

Thank You
TheMadScientist said:
You have a 950 u locked bootloader. First mistake trying to flash twrp. Only option you have is finding the revision bootloader you where on edl files and pinout to 9008 edl mode. There as of last known no fix other than for upload mode only.
Click to expand...
Click to collapse
Thank You I will try that And reply back with results

Gkeplar said:
Thank You I will try that And reply back with results
Click to expand...
Click to collapse
What revision bootloader was it on? I have several of them but not all

TheMadScientist said:
What revision bootloader was it on? I have several of them but not all
Click to expand...
Click to collapse
It was on its original bootloader for the Samsung Galaxy S8+ SM-G950U. It was SnapDragon bootloader

TheMadScientist said:
What revision bootloader was it on? I have several of them but not all
Click to expand...
Click to collapse
I'm working on reading this thread now trying to follow there instructions, https://forum.xda-developers.com/galaxy-s8/help/s8-g950u-hardbrick-t3668572

Gkeplar said:
It was on its original bootloader for the Samsung Galaxy S8+ SM-G950U. It was SnapDragon bootloader
Click to expand...
Click to collapse
Mate there are 7 different revisions of the 950 u bootloader. Across all the software updates. No offense intended. But if you can't even give this little bit of info I can assure you. Your not gonna be able to dissemble this device. Ground out the test points to enter edl. And flash needed repair files. Which is very tedious. If there is any issues. I would mark this device as lost and get another. I dont feel that you have the necessary skills needed to complete this process...
---------- Post added at 10:49 PM ---------- Previous post was at 10:38 PM ----------
Gkeplar said:
I'm working on reading this thread now trying to follow there instructions, https://forum.xda-developers.com/galaxy-s8/help/s8-g950u-hardbrick-t3668572
Click to expand...
Click to collapse
Unless you are on revision 2 bootloader that is no use to you
---------- Post added at 10:51 PM ---------- Previous post was at 10:49 PM ----------
Gkeplar said:
I'm working on reading this thread now trying to follow there instructions, https://forum.xda-developers.com/galaxy-s8/help/s8-g950u-hardbrick-t3668572
Click to expand...
Click to collapse
Unless you are on revision 2 bootloader that is no use to you
You are not in edl mode. You are stuck in upload. The only way to get to edl mode is disassemble the device flip the motherboard upside down while hooked up. Ground out a test pin on the mother board while connecting the usb cable.