Introduction
I've been researching on how to install TWRP on Zenfone Max with Final Marshmallow update for a long time, and finally found and gathered information on how to do so without any consequences. So if you're on final Marshmallow update and want to install TWRP on your phone, then this guide is for you! P.S. This is for Z010D only.
How To Install TWRP
1. Download this APK on your phone to unlock your bootloader : https://drive.google.com/open?id=0B-0qEY9zypslUTFKRE5CQUU5OFk
The app says it will wipe all data, but with my experience it doesn't wipe any data at all. However, I still recommend you to take a backup.
2. Download this zip to your computer and extract it : https://drive.google.com/file/d/0B2kFletApi72QkRLZnFURDUyZk0/view
3. Download this TWRP 3.2.3-0 image : https://sourceforge.net/projects/an...covery/TWRP-3.2.3-Z010D-20180729.img/download
4. Merge the TWRP 3.2.3 image to the extracted zip
5. Make sure you have USB Debugging on and put your phone into Fastboot mode [Hold Volume Up + Power] and connect it to the computer
6. In the extracted zip folder search bar, type 'cmd' and press Enter
7. Type 'fastboot devices' and press Enter, to see if your phone is detected
8. Type 'fastboot flash recovery TWRP-3.2.3-Z010D-20180729.img' and press Enter
9. Disconnect the phone and Hold 'Volume Down + Power', when you see the ASUS logo let go the Power, but keep holding Volume Down until you see the TWRP logo
Congratulations, you've successfully installed TWRP!
Video
If you're too lazy to read like me, here's the video : https://www.youtube.com/watch?v=EwuiHBIts7M
WhatzIt2Ya said:
Introduction
I've been researching on how to install TWRP on Zenfone Max with Final Marshmallow update for a long time, and finally found and gathered information on how to do so without any consequences. So if you're on final Marshmallow update and want to install TWRP on your phone, then this guide is for you!
Before We Get Started
Download these files on your phone and move it to the root of the storage :
1. Magisk 17.1 : https://github.com/topjohnwu/Magisk/releases/download/v17.1/Magisk-v17.1.zip
2. (Optional) TWRP 3.1.1 image : https://androidfilehost.com/?fid=745849072291687209
How To Install TWRP
1. Download this APK on your phone to unlock your bootloader : https://drive.google.com/open?id=0B-0qEY9zypslUTFKRE5CQUU5OFk
The app says it will wipe all data, but with my experience it doesn't wipe any data at all. However, I still recommend you to take a backup.
2. Download this zip to your computer and extract it : https://drive.google.com/file/d/0B2kFletApi72QkRLZnFURDUyZk0/view
3. Make sure you have USB Debugging on and put your phone into Fastboot mode [Hold Volume Up + Power] and connect it to the computer
4. In the extracted zip folder search bar, type 'cmd' and press Enter
5. Type 'fastboot devices' and press Enter, to see if your phone is detected
6. Type 'fastboot flash recovery Z010_3.0.0.t1_without_su.img' and press Enter
7. Disconnect the phone and Hold 'Volume Down + Power', when you see the ASUS logo let go the Power, but keep holding Volume Down until you see the TWRP logo
Congratulations, you've successfully installed TWRP!
Optional If you've downloaded TWRP 3.1.1 image, headover to 'Install' and select 'Install Image', then select the TWRP 3.1.1 image, then select Recovery and finally swipe to flash to update TWRP. To reboot back into recovery, press home, select reboot, and then recovery. You should see the TWRP version 3.1.1 upon reboot.
How To Root with TWRP
1. Boot into recovery and select 'Install'
2. Select Magisk zip and swipe to flash
3. Reboot to your OS, you should see a new app that is Magisk
Congratulations, you've successfully installed TWRP and Magisk!
Video
If you're too lazy to read like me, here's the video : https://www.youtube.com/watch?v=EwuiHBIts7M
Click to expand...
Click to collapse
Hey bro , seems you've been in mars and just arrived on Earth ! There's no issue whatsoever with installing twrp and rooting ZC550KL, there are lots of threads and video on YouTube about this for more than a year now.
jide1 said:
Hey bro , seems you've been in mars and just arrived on Earth ! There's no issue whatsoever with installing twrp and rooting ZC550KL, there are lots of threads and video on YouTube about this for more than a year now.
Click to expand...
Click to collapse
Yes, but some comments have issues where will it work with different versions (or updates), as the last update ASUS pushed was around Dec 17/Jan 18 with November 2017 security patch, some of the guides I've tried have failed, or had some issues. Also, some guides tell you to downgrade to marshmallow beta. Anyways, I just thought to do a final guide to root. ?
WhatzIt2Ya said:
Yes, but some comments have issues where will it work with different versions (or updates), as the last update ASUS pushed was around Dec 17/Jan 18 with November 2017 security patch, some of the guides I've tried have failed, or had some issues. Also, some guides tell you to downgrade to marshmallow beta. Anyways, I just thought to do a final guide to root.
Click to expand...
Click to collapse
so basically, is it all about unlocking the bootloader something to root the phone or what?
Singhisme said:
so basically, is it all about unlocking the bootloader something to root the phone or what?
Click to expand...
Click to collapse
Obviously, you need an unlocked bootloader to do any modifications! The only issue is, Asus phones don't show whether you have an unlocked bootloader or not. Sometimes the bootloader unlocker fails.
Jt380p said:
Obviously, you need an unlocked bootloader to do any modifications! The only issue is, Asus phones don't show whether you have an unlocked bootloader or not. Sometimes the bootloader unlocker fails.
Click to expand...
Click to collapse
Then how to be sure my device is locked or unlocked then?
Singhisme said:
Then how to be sure my device is locked or unlocked then?
Click to expand...
Click to collapse
Theres no sign. You just have to trust the app, unfortunately.
Urgent
Hi sir same way i did but TWRP is not showing.only black screen is displaying and i cant restart my phone please help me sir
twrp not showing
Jt380p said:
Theres no sign. You just have to trust the app, unfortunately.
Click to expand...
Click to collapse
I figure it out somehow.. there's something to do with ADB to check by this far it is the only way I know. thanks for the TWRP btw.. Good works!
Jt380p said:
Introduction
I've been researching on how to install TWRP on Zenfone Max with Final Marshmallow update for a long time, and finally found and gathered information on how to do so without any consequences. So if you're on final Marshmallow update and want to install TWRP on your phone, then this guide is for you! P.S. This is for Z010D only.
How To Install TWRP
1. Download this APK on your phone to unlock your bootloader : https://drive.google.com/open?id=0B-0qEY9zypslUTFKRE5CQUU5OFk
The app says it will wipe all data, but with my experience it doesn't wipe any data at all. However, I still recommend you to take a backup.
2. Download this zip to your computer and extract it : https://drive.google.com/file/d/0B2kFletApi72QkRLZnFURDUyZk0/view
3. Download this TWRP 3.2.3-0 image : https://sourceforge.net/projects/an...covery/TWRP-3.2.3-Z010D-20180729.img/download
4. Merge the TWRP 3.2.3 image to the extracted zip
5. Make sure you have USB Debugging on and put your phone into Fastboot mode [Hold Volume Up + Power] and connect it to the computer
6. In the extracted zip folder search bar, type 'cmd' and press Enter
7. Type 'fastboot devices' and press Enter, to see if your phone is detected
8. Type 'fastboot flash recovery TWRP-3.2.3-Z010D-20180729.img' and press Enter
9. Disconnect the phone and Hold 'Volume Down + Power', when you see the ASUS logo let go the Power, but keep holding Volume Down until you see the TWRP logo
Congratulations, you've successfully installed TWRP!
Video
If you're too lazy to read like me, here's the video :
Click to expand...
Click to collapse
anyone have working oem unlock tool for asus zenfone max (zc550kl).
tried so many tools,nothing worked for me
Android_Rom_OTA for ASUS Zenfone Max ZC550KL[Z010D]
Android_Rom_OTA:
Released /LineageOS-OMS/Z010D/lineage-14.1-20180821-UNOFFICIAL-Z010D-OMS.zip
Released /OreoTest/lineage-15.1-20180817-UNOFFICIAL-Z010D.zip
Released /TWRP_Recovery/TWRP-3.2.3-Z010D-20180729.img
Released /LineageOS/Z010D/lineage-14.1-20180729-UNOFFICIAL-Z010D.zip
Download Android_Rom_OTA
Related
I. Before You Begin
1. This could void the warranty of your device. We won’t be held responsible for anything that happens from doing this tutorial so please proceed at your own risk.
2. You need a Windows based PC in order to do this procedure.
3. You should have Motorola USB drivers installed on your PC. If you don’t, install them first.
4. This should erase all the data stored on your device. So, please backup everything that you’ll need.
5. This should also flash a custom recovery on your device.
How to Root the Motorola Moto X Play
Root the Moto X Play
Photo Credit: fonearena.com
To root the device, you’ll first unlock the bootloader, flash a custom recovery, and then flash SuperSU using the custom recovery to achieve root access. Here’s how:
II. Downloading Required Files
1. Download Fastboot and save it to your desktop.
Fastboot
2. Download TWRP Recovery and save it to your desktop.
TWRP Recovery
3. Download SuperSU and save it to your desktop.
SuperSU
III. Unlocking the Bootloader on the Motorola Moto X Play
1. Extract files from Fastboot over to your desktop by right-clicking on it and selecting Extract here.
2. Turn off your device.
3. Turn your device back on in fastboot mode. To do that, hold down Volume DOWN and Power buttons together for a few seconds.
4. Your device should now be in fastboot mode.
5. Plug in your device to your PC using a USB cable.
6. Launch a Command Prompt Window on your desktop by holding down Shift and right-clicking anywhere on the screen and selecting Open command window here.
7. Type in the following command into the Command Prompt Window and hit Enter:
Code:
fastboot oem get_unlock_data
8. You should see a string of text on your screen. Copy it to your clipboard removing any spaces so that it is a long string of text.
9. Head over to the Motorola Bootloader Unlock website and get yourself logged-in. If you don’t have an account with them, create one now.
10. One of the steps on that website will ask you to paste the string of text. Just paste the string that you’ve already copied to your clipboard and follow the on-screen instructions.
11. You’ll receive an unlock key to your email address. Copy that key to your clipboard.
12. Now, type in the following command replacing KEY with the actual unlock key that you’ve copied to your clipboard and hit Enter:
Code:
fastboot oem unlock KEY
13. Wait for it to unlock the bootloader on your device.
14. When it’s done unlocking the bootloader, reboot your device by issuing the following command:
Code:
fastboot reboot
15. Your device should reboot.
And there you go.
The bootloader on your Motorola Moto X Play is now unlocked, and you can now flash a custom recovery on your device. Here’s how you can do that:
IV. Flashing a Custom Recovery on the Motorola Moto X Play
1. Turn off your device.
2. Reboot your device into fastboot mode by holding down Volume DOWN and Power buttons together for a few seconds.
3. Connect your device to your PC using a USB cable.
4. Open a Command Prompt Window on your desktop. To do that, hold down Shift and right-click anywhere on your screen and select Open command window here.
5. Type in the following command into the Command Prompt Window and hit Enter. Make sure to replace recovery.img with the actual name of the recovery image that you have downloaded.
Code:
fastboot flash recovery recovery.img
6. Wait for it to flash a custom recovery on your device.
7. When it’s done flashing a recovery, reboot your device by using the following command:
Code:
fastboot reboot
8. Your device should reboot.
Your Motorola Moto X Play now has a custom recovery using which you can gain root access on your device. Here’s how:
V. Rooting the Motorola Moto X Play
1. Connect your device to your PC using a USB cable.
2. Copy SuperSU .zip from your desktop over to the internal SD card storage on your device.
3. Unplug your device from your PC when SuperSU is copied.
4. Turn off your device.
5. Turn your device back on in recovery mode. To do that, hold down Volume DOWN and Power buttons together.
6. Your device should reboot into bootloader mode.
7. Select Recovery from the options appearing on your screen.
8. Select Install in the recovery menu.
9. Choose SuperSU .zip to be installed on your device.
10. Tap on Swipe to Confirm Flash to confirm flash.
11. Wait for it to flash SuperSU on your device.
12. When it’s done flashing SuperSU, reboot your device by selecting Reboot followed by System in the recovery menu.
13. Your device should reboot.
Source: http://theunlockr.com/2015/09/21/root-motorola-moto-x-play/
Nice plagiarism here..... [emoji35]
How is it plagiarism if I have mentioned the source?
going into recovery mode gives me the dead android with the red triangle logo with the text "no command." under it. i tried both twrp versions.
Auros42 said:
going into recovery mode gives me the dead android with the red triangle logo with the text "no command." under it. i tried both twrp versions.
Click to expand...
Click to collapse
The same here (Dual-Sim-Version) :crying:
Also link forFastboot ist down
route9 said:
The same here (Dual-Sim-Version) :crying:
Also link forFastboot ist down
Click to expand...
Click to collapse
Make sure you get this version.
twrp-lux-2.8.7-v2.img
for fastboot:
http://forum.xda-developers.com/showthread.php?t=2317790
This works, I tried that, I have root now
Enviado desde mi XT1562 mediante Tapatalk
I can confirm that this recovery worked.
Model India Moto X Play Dual Sim - (xt1562)
route9 said:
The same here (Dual-Sim-Version) :crying:
Also link forFastboot ist down
Click to expand...
Click to collapse
Flash TWRP again & boot TWRP before booting Android again. The stock rom tries to replace TWRP but TWRP will fix that on its first boot.
mahir1995 said:
Flash TWRP again & boot TWRP before booting Android again. The stock rom tries to replace TWRP but TWRP will fix that on its first boot.
Click to expand...
Click to collapse
There was trouble with opening bootloader. I used a opening-tool, which said, that the device bootloader is now open - but it wasn´t. Everything´s ok now. I managed bootloader-opening with cmd.exe.
I think this thread should be titled "tested" instead of "untested".... works great! thanks
Dear Android Gurus,
I am new to XDA forum. I am going to try rooting my new Moto X Play and I am pretty excited about this as I am trying this for the first time. Can someone please confirm if the steps given here or in theunlockr website works for Moto X Play?
Mine is the Indian version - Model# XT1562 and below are the details. Please advice.
Hardware SKU: XT1562
Baseband Version: M8936_2020613.22.03.21.33R
LUX_EMEA_DSDS_CUST
Kernel version:
3.10.49-g6d623da
[email protected] #1
Wed Jul 15 21:06:16 CDT 2015
System version
23.21.10.lux_retasia_ds.retasiaall.en.03 retin
Build number
LPD23.118-10
koolkans said:
Dear Android Gurus,
I am new to XDA forum. I am going to try rooting my new Moto X Play and I am pretty excited about this as I am trying this for the first time. Can someone please confirm if the steps given here or in theunlockr website works for Moto X Play?
Mine is the Indian version - Model# XT1562 and below are the details. Please advice.
Hardware SKU: XT1562
Baseband Version: M8936_2020613.22.03.21.33R
LUX_EMEA_DSDS_CUST
Kernel version:
3.10.49-g6d623da
[email protected] #1
Wed Jul 15 21:06:16 CDT 2015
System version
23.21.10.lux_retasia_ds.retasiaall.en.03 retin
Build number
LPD23.118-10
Click to expand...
Click to collapse
Bro, don't root if you root u will not receive android marshmallow update for your phone, and u will lose your warranty
RahulPrasad said:
Bro, don't root if you root u will not receive android marshmallow update for your phone, and u will lose your warranty
Click to expand...
Click to collapse
Why not? You can get the better system, called CyanogenMod . And after i tested my phone for 3 weeks i dont need warrenty. Works perfect, and cm 12.1 with a new kernel is fantastic.
Bye, Klaus
RahulPrasad said:
Bro, don't root if you root u will not receive android marshmallow update for your phone, and u will lose your warranty
Click to expand...
Click to collapse
Hi Rahul, Do you mean I should wait for the marshmallow update to be done and after that I can root or should I wait till the warranty period gets over?
If you root you will be able to get any marshmallow rom that is available for the phone anyway. So don't worry about that nonsense. The warranty however is a different issue. It's all about whether you see the 'risk' as worth it.
Work !!
I root it in ten minute, thanks.
Can it be changed to say 'tested and works great', as it does.
Sent from my XT1562 using Tapatalk
I also have a concern on rooting. I like Moto Display function, so if I root it, I will lose it, so I will not.
SteveCC said:
I also have a concern on rooting. I like Moto Display function, so if I root it, I will lose it, so I will not.
Click to expand...
Click to collapse
That's a function of the ROM. I'm rooted with a custom recovery and stock ROM, and still have it.
Hi I've unlocked the bootloader of my phone but I can't find any recoveries to push through ADB, therefore I can't flash SU. Does someone have a solution ?
Allright, for the newcomers, I've found a solution for this : (it is very important that you don't update your rom if you've rooted your phone, unless you want a 150$ brick I guess !)
Don't forget to install adb before anything
1. Enable USB debugging in developers option.
2. Connect your phone to a computer and then launch cmd. Type «adb reboot fasboot».
3. Once in fastboot mode we will flash TWRP by typing this : «fastboot flash recovery 1streco.img».
4. Unplug and reboot your device, on the nag screen keep pressing the up volume button to enter recovery. If it doesn't work then choose shutdown and hit all three buttons while it's booting.
5. Once you are in TWRP, backup everything to extsdcard.
6. Go to wipe and format /data and wipe it under advanced wipe. DO NOT TOUCH ANY OTHER PARTITION !!! ONLY DATA.
7. Once it's done reboot the device. You should have a message telling you that the encryption failed, click reset phone.
8. It should launch TWRP choose reboot to bootloader.
9. Once in fastboot mode type this : «fastboot flash recovery 2ndreco.img» then type : «fastboot reboot».
10. Your phone should now display : «Factory reset low level» when you click reset phone. Once it's done it will automatically reboot but don't let it finish his boot sequence yet. On the nag screen keep pressing the up volume to enter recovery and then choose shutdown.
11. Boot in fastboot mode again and type : «fastboot flash recovery 1streco.img», then : «fastboot reboot».
Hold the vol.up button while on nag screen to enter TWRP.
If you don't enter TWRP after you typed fastboot reboot and hit the vol.up button but you enter erecovery that's ok, in this case what you need to do is to choose shutdown. Then hold vol.up, vol.down and power buttons to enter TWRP ! Go to install and flash magiskv13.3.zip and voilà your phone is now rooted !
I've not tried but I think you could restore the data partition with TWRP once you've done all those steps but I can't guarantee you anything so this is why I've told you to backup your data.
1streco.img file link here
2ndreco.img file link here
Magisk v13.3 link here
Si I've been able to install twrp but when I try to flash SuperSu.zip it doesn't work. It's crazy !
For those who wants to know, I've tried everything and the only way to go is to format and wipe data in order to disable dm-verity. But if you do that you won't be able to go further because the rom asks you to crypt your datas before continuing....
Ilovelife76 said:
For those who wants to know, I've tried everything and the only way to go is to format and wipe data in order to disable dm-verity. But if you do that you won't be able to go further because the rom asks you to crypt your datas before continuing....
Click to expand...
Click to collapse
hi, please you can explain me how to obtain root? I have unlocked the bootloader of my phone. Sorry my english. thanks
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Ilovelife76 said:
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Click to expand...
Click to collapse
So, Ilovelife76, have you managed to root your Honor 6C successfully? (And how, if so? )
Ilovelife76 said:
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Click to expand...
Click to collapse
Long-time away from home
I Need to root my Honor 6C... Can anyone help me ?
sub7even12 said:
I Need to root my Honor 6C... Can anyone help me ?
Click to expand...
Click to collapse
He is away from home it seems and no confirmation on rooting. More wait.
Ilovelife76 said:
I'll explain it when I'll be back home and I'll upload files here. You will lose everything tho so backup all your data now
Click to expand...
Click to collapse
Still away from home.
Here's the solution
Hi guys ! Sorry for the wait but here it is, my tutorial to the graal, root on this device :
1. Enable USB debugging in developers option.
2. Connect your phone to a computer and then launch cmd. Type «adb reboot fasboot».
3. Once in fastboot mode we will flash TWRP by typing this : «fastboot flash recovery 1streco.img».
4. Unplug and reboot your device, on the nag screen keep pressing the up volume button to enter recovery. If it doesn't work then choose shutdown and hit all three buttons while it's booting.
5. Once you are in TWRP, backup everything to extsdcard.
6. Go to wipe and format /data and wipe it under advanced wipe. DO NOT TOUCH ANY OTHER PARTITION !!! ONLY DATA.
7. Once it's done reboot the device. You should have a message telling you that the encryption failed, click reset phone.
8. It should launch TWRP choose reboot to bootloader.
9. Once in fastboot mode type this : «fastboot flash recovery 2ndreco.img» then type : «fastboot reboot».
10. Your phone should now display : «Factory reset low level» when you click reset phone. Once it's done it will automatically reboot but don't let it finish his boot sequence yet. On the nag screen keep pressing the up volume to enter recovery and then choose shutdown.
11. Boot in fastboot mode again and type : «fastboot flash recovery 1streco.img», then : «fastboot reboot».
Hold the vol.up button while on nag screen to enter TWRP.
If you don't enter TWRP after you typed fastboot reboot and hit the vol.up button but you enter erecovery that's ok, in this case what you need to do is to choose shutdown. Then hold vol.up, vol.down and power buttons to enter TWRP ! Go to install and flash magiskv13.3.zip and voilà your phone is now rooted !
I've not tried but I think you could restore the data partition with TWRP once you've done all those steps but I can't guarantee you anything so this is why I've told you to backup your data.
1streco.img file link here
2ndreco.img file link here
Magisk v13.3 link
Hey, great that you found your way home.
Ilovelife76 said:
1streco.img
2ndreco.img
Click to expand...
Click to collapse
Can you tell us a little more about these two files? Where have you found them? (Not wanting to sound too paranoid but you know...)
I've found 1streco.img on a Chinese board. It's the work of a guy who managed to make TWRP available to us, users of honor 6c. The second one is the standard recovery image of Honor 6c. Those files are good, don't worry. Once your phone is rooted and everything works good, you can of course update magisk through TWRP to the lastest version.
OK, I have been trying around now for an hour or so... I have one real problem and one possible problem:
1. (the real one) Using Win7 64 bit, each time I send the the phone into fastboot mode, the system tries to install "MTP USB device" drivers... without any success so far. That's why the phone boots normally again. I haven't been able to solve that so far (installed HiSuite for example, didn't help).
2. (the possible one) Should the bootloader be unlocked? If yes, I have to admit I haven't found a way to do that so far. :-/
Of course the bootloader must be unlocked before doing anything, you can request a code here on Huawei website : http://en.ui.vmall.com/plugin.php?id=unlock
bravo there is machine back or full backup with recovery
Did you manage to root your phone ?
beautiful, can you install a module on magisk? if yes how because when installing the modules I get a failure when editing magisk.img thanks ?
No, you can't because of dm-verity, you.can manually install via recovery tho.
For the Russian version 6s failed to implant. ADB reboot fastboot this command does not put the phone in fastboot mode.
Thx to topjohnwu you can use magisk on EMUI9. https://github.com/topjohnwu/magisk_files/tree/master/canary_builds
What you need:
1. Unlocked Bootloader
2. be able to use twrp 3.2.3-1 (important! 3.2.3-1). In this case, im using latest offical twrp for the Huawei P20 Pro (charlotte). Only use ADB function, other features (backup/restore) are untested by me, it can harm your device eventually if you use other functions then ADB.
3. adb installed on PC
4. all-full-release.apk from https://github.com/topjohnwu/magisk_files/tree/master/canary_builds
5. magisk-release.zip from https://github.com/topjohnwu/magisk_files/tree/master/canary_builds
OK, so how we root the Honor 10 with EMUI9.0?
1. Download offical twrp from here: https://dl.twrp.me/charlotte/twrp-3.2.3-1-charlotte.img.html.
Be careful, this release was made for another device, but i had no issue with it on my Honor 10.
2. Download Magisk Manager (all-full-release.apk) from https://github.com/topjohnwu/magisk_files/tree/master/canary_builds and install it.
3. Download magisk root (magisk-release.zip)
4. Enable OEM Unlock (so you can flash recovery in fastboot) , Power Off the device, push and hold VOL DOWN and plug in the usb cable. The device will start into fastboot.
5. Flash Twrp withon the PC: fastboot flash recovery_ramdisk twrp-3.2.3-1-charlotte.img
6. This one is a bit tricky! Type fastboot reboot, push and hold VOL UP and after sending fastboot reboot immediately remove cable and wait for twrp to boot. If you not remove the cable you will end up in eRecovery and have to redo the steps above.
7. In twrp, go to advanced and start ADB. Than plug in the USB cable.
8. PC: flash magisk-release.zip with: adb sideload magisk-release.zip
9. IMPORTANT: Remove cable, select reboot, but keep VOL UP pressed during reboot, otherwise you are not able to use magisk. You have to press VOL UP everytime you reboot the device otherwise you have to do Step 5-9 again.
10. Done, your device is rooted.
UPDATE to .162:
To Update succsessfully to .162 you have to do the following things:
1. flash emui stock recovery_ramdisk.img in fastboot (extract it from update.app using Huawei Update Extractor) use "fastboot flash recovery_ramdisk RECOVERY_RAMDIS.IMG" You dont have to use recovery_ramdisk.img from .162. Just use the latest update.app to extract the recovery_ramdisk.img you can find in Firmware Finder.
2. Disable OEM Unlock and reboot the device
3. Go to Settings\System\Software Updates and Hit the 3 Dots on the top right. Select the Full Package Download.
4. Wait until download is complete and hit update. Now the device will boot into EMUI recovery and install the update the phone.
5. The device is now rootless, if you want root again, follow the instructions above.
Caution: Just in case: After the update and installation of magisk, adaway becomes unstable on my phone. It seems the "allow root" popup dont show up after adaway started. I have fixed this by autoallow root in magisk, start adaway, enable adblocking and set magisk to "ask permissions" again. After this, the popup shows correctly again. For now i have no clue why this was happen, another Honor 10 dont have this issue at all.
albysprx said:
Just disable battery optimization for magisk manager and the "allow root" popup will appear
Click to expand...
Click to collapse
Notice for UPDATE .179:
You can use the guide above but you have to update (Systemupdate) twice, since the update comes with 2 separate packages. After the first run, emui recovery shows "update failed". Just reboot to system, go to settings, and start the updateprocess again. The second package is about ~220MB in size. After this follow the guide above to get magisk running again.
Notice for UPDATE .203:
Just do the usual way. Flash STOCK recovery_ramdis.img with fastboot, reboot the phone, do the update. After this flash twrp in fastboot again and adb sideload magisk-release.zip.
Notice for UPDATE .207:
Works! Flash STOCK recovery_ramdis.img with fastboot, reboot the phone, do the update. After this flash twrp in fastboot again and adb sideload magisk-release.zip.
Notice for UPDATE .216:
Works!
Notice for UPDATE .223:
Works, but you have to use latest Magisk release (19.3) from topjohnwu: https://github.com/topjohnwu/Magisk/releases
At step 8. PC: flash magisk-v19.3.zip with: adb sideload Magisk-v19.3.zip
Notice for UPDATE EMUI 9.1:
9.1 Change a lot, you will have the latest stock RECOVERY_RAMDISK.IMG patched via Magiskmanager and install that with fastboot. After this, reboot and PRess VOL+. You will end up in eRecovery, hit Wipe/Factory Reset(Make BACKUP!) and reboot. This install magisk permanently. For Adaway: You need Systemless Mode activated in Magisk and Adaway.
Maybe i will write another Guide for 9.1, but for now im testing stability.
Thanks a lot man!
Well P20 hardware share similarity with honor 10. Twrp should work logically but you never know when you came up against something bad so I will for now hehe
Sent from my Honor 10 using XDA Labs
Will it work with mate 10 pro emui 9?
neo2k17 said:
Will it work with mate 10 pro emui 9?
Click to expand...
Click to collapse
I've tested and it works
Hi, either it's not working for me or i'm stuck somewhere.
Steps 1-5 are working.
Then it reboot the device with fastboot reboot and press&hold the vol up.
But my phone doesn't boot into twrp. All i get is erecovery.
When i turn the phone off, no usb cable plugged in and try to get into twrp by press&hold power + vol up i get:
error mode
attention!
please update system again
error!
func no: 11 (recovery image)
func no:2 (load failed!)
Click to expand...
Click to collapse
Normal boot still worked fine.
What am i doing wrong?
I just updated from 8.1 to 9 today fyi.
edit: after flashing my latest twrp image that worked i can access twrp recovery again.
but everything at /sdcard looks encrypted since all folders and files have crazy names like asdfASdfasdFGADSgm
I currently don't have any password etc. on my honor.
leAndroid91 said:
edit: after flashing my latest twrp image that worked i can access twrp recovery again.
but everything at /sdcard looks encrypted since all folders and files have crazy names like asdfASdfasdFGADSgm
I currently don't have any password etc. on my honor.
Click to expand...
Click to collapse
Android 9 comes with build in crypto, so its perfektly normal to see folders like "akgaufagkiugsduiphps". Thats the reason we have to use ADB with latest TWRP, only 3.2.3-1 has support for it. So i beleive, if you cant get 3.2.3-1 running, you cannot have magisk atm.
ThreeMMM said:
Thx to topjohnwu you can use magisk on EMUI9. https://github.com/topjohnwu/magisk_files/tree/master/canary_builds
1. Download offical twrp from here: https://dl.twrp.me/charlotte/twrp-3.2.3-1-charlotte.img.html.
Be careful, this release was made for another device, but i had no issue with it on my Honor 10.
2. Download magisk (all-full-release.apk) from https://github.com/topjohnwu/magisk_files/tree/master/canary_builds and install it. Its Magisk Manager.
3. Download magisk-release.zip
4. Disable OEM Unlock, Power Off device, push and hold VOL DOWN and plug is the usb cable. The device will start into fastboot.
5. Flash Twrp with: fastboot flash recovery_ramdisk twrp-3.2.3-1-charlotte.img
6. Type fastboot reboot, push and hold VOL UP until device boots into twrp.
7. In twrp start ADB
8. PC: flash magisk-release.zip with: adb sideload magisk-release.zip
9. IMPORTANT: Select Reboot but keep VOL UP pressed during reboot, otherwise you are not able to use magisk.
Click to expand...
Click to collapse
Thx a lot! Works fine
One question about 9. - I had to remove the cable first, otherwise by pushing VOL UP+reboot it goes directly to eRecovery-mode?!
Uhm ... just one question for my understanding.
How am i supposed to flash a new recovery in step 5 when i disable oem unlock in step 4?
As far as i know deactivating oem unlock prevents from flashing even if the bootloader is already unlocked.
leAndroid91 said:
Uhm ... just one question for my understanding.
How am i supposed to flash a new recovery in step 5 when i disable oem unlock in step 4?
As far as i know deactivating oem unlock prevents from flashing even if the bootloader is already unlocked.
Click to expand...
Click to collapse
You're right, i just went through without reading that point correctly. It's a little bit misleading
Sorry guys, i have edit the Post so now its more clear what to do. Thanks for the hints, it a pleasure to contribute to such a nice community! Keep rockin!
Haj
point 2
Installation Magisk all-full-release.apk. The application is installed, additional files are downloaded, but end with the message "Magisk not installed". Is this how it should be?
By keeping oem unlocked i was able to flash twrp, too.
And i was able to boot into twrp.
But for /sdcard it kept showing me the encrypted files and folders
What's the reason behind:
9. IMPORTANT: Remove cable, select reboot, but keep VOL UP pressed during reboot, otherwise you are not able to use magisk. You have to use this everytime you reboot the device.
Click to expand...
Click to collapse
Is magisk checking if vol up is pressend and then activates, otherwise it stays inactive?
edit:
i was not able to boot like mentioned in step 9.
1st try: i got stuck at "your device is booting now..." (still pressing vol up).
Then released vol up and waited for another 3-4 minutes but nothing happend.
2nd try: When not pressing any button my phone booted as expected but without magisk.
3rd try: Then i shut it down again.
Turned it on, pressend and hold vol up but i just got into eRecovery.
Any ideas?
Does this method keep magisk permanently after the first boot or do I need to repeat the procedure every time if my bootloader is locked?
Coraz said:
Does this method keep magisk permanently after the first boot or do I need to repeat the procedure every time if my bootloader is locked?
Click to expand...
Click to collapse
You don't have to do the whole procedure except step 9, you have to push VOL UP during every reboot to keep magisk active.
p. 2
magisk (all-full-release.apk) install.
select method:
- Download zip only
- Patch boot image file (then click)???
kmarek11 said:
p. 2
magisk (all-full-release.apk) install.
select method:
- Download zip only
- Patch boot image file (then click)???
Click to expand...
Click to collapse
Just install the app and go on with step 3.
To install using a zip file?
kmarek11 said:
To install using a zip file?
Click to expand...
Click to collapse
Install the apk file, the zip file is for rooting your device via adb sideload.
I am installing magisk (all-full-release.apk) from the given link
the application appears on the phone
in the magisk application I click "installation" I get communication, do you want to install Magisk-v18.0 (18000) zip? and choice:
1 I do not thank you
2 changes
3 this installation I click and the "Choose method" message is displayed: and the option to choose
1 download only zip or
2 Patching the boot image file
Which one to choose to go to the next steps?
First of all the guide i took it from @Vedrick by searching here in XDA. I just opened this post because i found his guide with a little bit hardness and its easier now for ya.
Well lets start. FIRST Back up all your data.
I was on the latest version of CLT-L29 Huawei p20 pro 6/128 9.0.0.195(C432E5R1P9) if you try it on another version let me know
As always, if you do this it's at your own risk.
PREREQUIREMENTS:
Watch my video on youtube that made to help you guys
1) ADB, Fastboot and Drivers
2)Patched boot image
3) A pc of course.
4) Make sure your phone is not bootloop and working
5)Enable Debugging and OEM unlocking from dev options
This is how i got root on EMUI 9 without TWRP recovery
1 - I Flashed Get your phone on fastboot mode FIRST MAKE SURE YOUR PHONE HAS UNLOCKED BOOTLOADER (download it, and move it on your adb folder-default is on C: drive) (press SHIFT button and right click on the adb folder->select open here PowerShell) type the command fastboot flash recovery_ramdisk patched_boot.img
2-Reboot phone, install Magisk manager last apk from google , go into settings, and change the update channel to custom: )COPY AND PASTE THIS LINKhttps://raw.githubusercontent.com/topjohnwu/magisk_files/master/canary_builds/release.json, go back to the Magisk home screen and hit install, download the odd Magisk file.zip file.
3-Reboot phone, press and hold the volume up key if it goes to ERecovery then reboot again and keep pressing like the video.
4-Open Magisk app, install the zip, then patch, and install the downloaded Magisk.zip file if it says direct install(recommender choose this should say this)
5-Reboot phone, press and hold the volume up key and your phone should boot just fine.(like i said above and like i show the video)
6-Open Magisk, install, select direct install option. and reboot.
Note:
1 - Now your phone will reboot into the recovery every time on its own, which is a good thing, you no longer need to hold the volume up key every time you reboot, it does it for you. This means no TWRP.
2 - In order to apps root access for the first time you need to have Magisk open, or you wont get prompted for approval. Then the app will have permanent root access.
3- You can enter fastboot mode from connecting your phone to pc and open adb as i say above and type adb reboot bootloader OR by turn off your phone, press the down button volume and after 3 secs connect the cable on your pc DONT LEAVE THE DOWN BUTTON
Usefull Commands: If you cannot enter bootloader mode ( IS NEEDED ) type this command on the adb , but first connect your phone with your PC/LAPTOP adb reboot bootloader
IF you have any questions fell free to comment bellow. Also i am gonna try some things to flash twrp and have it for ever because @Vedrick i think couldnt flash twrp recovery
Hi,
thanks a lot taking time for this guide but there are 2 things that I think are confusing :
FIRST - Once you have flashed recovery_ramdisk partition with the patched_boot.img file through fastboot , and you reboot holding up volume button, the phone boots. But after installing latest magisk manager, even without changing the update channel adress, phone is already rooted and you can add modules, etc...
SECOND - when following the guide step by step, part 4 is a problem because it finds new version and asks tout update. And when you do, the guide says install then to patch the tout install the downloaded file.
That part ils not clear as you do not tell what file to patch at this state....
If you could clear that part it would be perfect.
deltaman83 said:
Hi,
thanks a lot taking time for this guide but there are 2 things that I think are confusing :
FIRST - Once you have flashed recovery_ramdisk partition with the patched_boot.img file through fastboot , and you reboot holding up volume button, the phone boots. But after installing latest magisk manager, even without changing the update channel adress, phone is already rooted and you can add modules, etc...
SECOND - when following the guide step by step, part 4 is a problem because it finds new version and asks tout update. And when you do, the guide says install then to patch the tout install the downloaded file.
That part ils not clear as you do not tell what file to patch at this state....
If you could clear that part it would be perfect.
Click to expand...
Click to collapse
i am gonna check it now because my phone was bricked and i cant root now
deltaman83 said:
Hi,
thanks a lot taking time for this guide but there are 2 things that I think are confusing :
FIRST - Once you have flashed recovery_ramdisk partition with the patched_boot.img file through fastboot , and you reboot holding up volume button, the phone boots. But after installing latest magisk manager, even without changing the update channel adress, phone is already rooted and you can add modules, etc...
SECOND - when following the guide step by step, part 4 is a problem because it finds new version and asks tout update. And when you do, the guide says install then to patch the tout install the downloaded file.
That part ils not clear as you do not tell what file to patch at this state....
If you could clear that part it would be perfect.
Click to expand...
Click to collapse
ok i did manage to root it again. you need to unlock your bl and press the volume up button. i edited the post
I did first time as just flashing fastboot recovery_ramdisk with patched_boot.img was enough when opening magisk manager.
Updating was the issue. SO i downloaded the original recovery_ramdisk 195 , and used that file to patch with the latest version downloaded. Then I flashed in fastboot the new patched_boot.img and all was good to latest version.
deltaman83 said:
I did first time as just flashing fastboot recovery_ramdisk with patched_boot.img was enough when opening magisk manager.
Updating was the issue. SO i downloaded the original recovery_ramdisk 195 , and used that file to patch with the latest version downloaded. Then I flashed in fastboot the new patched_boot.img and all was good to latest version.
Click to expand...
Click to collapse
why to download another patch i dont get it.
plus see my signature
Because with yours i was not on latest magisk. Now i can update each time there's a new version by patching the original recovery_ramdisk and flashing the patched_boot.img on fastboot.
I'm curently on 18.2-e05cdc83 (18104)
deltaman83 said:
Because with yours i was not on latest magisk. Now i can update each time there's a new version by patching the original recovery_ramdisk and flashing the patched_boot.img on fastboot.
I'm curently on 18.2-e05cdc83 (18104)
Click to expand...
Click to collapse
i have the same version as you. the problem is 1) you cant have twrp recovery 2) when you open a app that needs root you have to open magisk app first otherwise the permissions will fail
unfortunately no twrp recovery ...
You're right I noticed that
deltaman83 said:
unfortunately no twrp recovery ...
You're right I noticed that
Click to expand...
Click to collapse
do no try to flash twrp it bricked my device.,
Join my telegram group dude
Thanks a lot but i don't have enough time....see m'y number of posts by there lol...same on Facebook etc (f..k I'm already late for work....?).
Regards
Hi all, this method will work on my device? thanks!
P20 PRO
model: CLT-L09
Build: 9.0.0.163 (C432E5R1P9patch01) GPU Turbo
EMUI: 9.0.0
Android 9
Evasi0n3r said:
Hi all, this method will work on my device? thanks!
P20 PRO
model: CLT-L09
Build: 9.0.0.163 (C432E5R1P9patch01) GPU Turbo
EMUI: 9.0.0
Android 9
Click to expand...
Click to collapse
Hello yes sir.
Please check my signature and join my telegram
Watch my video on youtube that made to help you guys https://youtu.be/AB6wwBTfKEc
Hi. Thank you.
I did it in firmware 9.0.0.191 and worked fine.
gvflavio said:
Hi. Thank you.
I did it in firmware 9.0.0.191 and worked fine.
Click to expand...
Click to collapse
np if u want press the thanks button. also join my telegram group see the link in my signature bellow this post.
John
You are genius. Thanks working great p20 pro 9.0.0.191c605
Every time I flash the patched_boot.img and restart with volume up into recovery I have a bootloop. I have CLT-L09 pie 9.0.0.1.9.5 with the custom link for magisk. The only way to get out of the loop is to reflash the stock recovery_ramdis.img. But after flashing stock recovery, magisk has no root any more...
Any suggestions why I only get the bootloop after reflashing the patched_boot.img?
Thanks a lot!
mauritz1972 said:
You are genius. Thanks working great p20 pro 9.0.0.191c605
Click to expand...
Click to collapse
Do you have a problem when you try to pull down the quick setting touching the right or left corner of the screen?
That happens to me when I rooted it.
I need to unlock bootloader with some key, or can i just follow the guide?
Found this while trolling through the Chinese forums, none of this is my work, I have translated the instructions as best I can.
Disclaimers; I have not tried this, it may brick the global rom, the custom recovery is likely only in Chinese language.
You need:
Boot Loader unlock code (currently probably not possible to get)
Huawei USB drivers
Recovery image (attached)
Magisk package (attached)
files: https://mega.nz/#!PM0EmYLA!384hZjmJ9ExNc7Q8rSqssHunWSO7AxQ3GA4qet6RX4E
Extract files to a folder, open command prompt and change into this folder.
Unlock bootloader (BL unlock will clear the phone data, please do a backup)
- Obtain an official unlock code
- double-click to open the "Huawei Toolbox.exe"
- click "unlock bootloader "
- enter the unlock code in the pop up window , click OK, and wait for the phone to unlock complete restart.
Flash the third-party recovery
- Turn off the phone and connect the computer. Press and hold the “Volume Down” button and “Power button” until the phone displays the android page and release your finger.
- open command prompt and run:
fastboot flash recovery_ramdisk twrp.img
- after seeing the two OKAY feedback from the command line, the flash is successful.
Enter recovery to flash root image (this step will clear all data of the mobile phone including memory card, please make a backup in advance)
- long press “Volume Up” and “Power” ", until you see the a twrp logo, release the keys and wait to enter recovery mode
- After entering recovery, click the second item “Clear”, click “Format Data Partition” in the lower left corner, slide the slider to enter the clear, wait for the progress bar to complete
- Return to the recovery homepage, click on the last item "Advanced", select the last item "Remove data forced encryption", slide the slider to release, wait for completion
Copy the root package to the phone
- In Command Prompt type or copy the following commands
adb push magisk-installer.zip /sdcard
adb push magisk.apk /sdcard
Install Image
- Whilst still in recovery mode, click the first item to install the magisk-installer.zip package from the sdcard , slide the slider to install, wait for the flash to complete, and restart the phone
- After reboot is complete, click “File Manager”, select the apk file “magisk.apk” just copied from the memory card when install is finished, open the magisk app and click “No, thank you” in the pop-up window
- Return to the command line tool, type the code to execute, and wait for the phone to automatically restart
Fastboot reboot recovery
- after the restart, open "magisk", it should show that the installation is complete, that is, ROOT is achieved.
Anything in that forum on how to manually update phone?
technotika said:
Anything in that forum on how to manually update phone?
Click to expand...
Click to collapse
That is actually what I was looking for
But none, problem is the v20 (china version) seems to get OTA way before us, they all got v143 2 weeks ago.
I did find the menu to do it, but it only supports if the image is stored on an sdcard, and when I click it it says no sdcard found. so its impossible.
Tried same with similar results. One day eh? ?
İ have V20 chinese version. İ want to root but could not find a way. Can you share the chinese forum maybe i can find how to unlock bootloader
greenblueye said:
İ have V20 chinese version. İ want to root but could not find a way. Can you share the chinese forum maybe i can find how to unlock bootloader
Click to expand...
Click to collapse
If you read what I wrote in the first post you would see you cannot root without a bootloader unlock code.
Tested! Work bootloader code on Russia services (Cost 20USD)
belam00r said:
Tested! Work bootloader code on Russia services (Cost 20USD)
Click to expand...
Click to collapse
Nice! Did unlocking bootloader factory reset your device?
Yes of course. All new Huawei and Honor do a reset after unlocking
i get bootloader unlock code from funkiehuwai for 20$
any one tried this instructions and have success?
I just wonder comments below will work?
*adb push magisk-installer.zip /sdcard
*adb push magisk.apk /sdcard
because there is no sd card support for view20?
when i opened huawei-toolbox.exe its in chinese and im afraid to continue other instructions
Did anyone use TWRP and which version?
Did the View 20 Boot correctly?
I read in a Forum, that with the view 20 doesn´t boot correctyl with TWRP. The reason should bei the Storage...
Best regards
Unlocked Bootloader
belam00r said:
Tested! Work bootloader code on Russia services (Cost 20USD)
Click to expand...
Click to collapse
Does that mean you rooted you device (with the files from above) or you just unlocked the bootloader?
I was able to unlock my bootloader with a code from funkyhuawei (about 18 €, site seems to be down currently). I did not use the unlock tool above, mainly because its chinese
- Enabled "USB debugging" and "OEM unlock" in developer settings
- Connected phone to PC, opened adb and used "adb reboot bootloader"
- Unlocked via "fastboot oem unlock *16digit code*"
This worked out fine. However, as far as i understand it magisk is installed over twrp (recovery_ramdisk), removing twrp but granting you root. This makes me kind of nervous since twrp has been a nice safety net on several occasions. This is why I stopped after unlocking the bootloader. Maybe someone has more experience on this? Why is there so little interest in rooting this phone?
Regards
root achieved
I don't know if nobody's interested or nobody wants to try rooting this phone. However, I just went ahead and tried it. I used this guide: https://topjohnwu.github.io/Magisk/install.html#emui-9 (posted in https://forum.xda-developers.com/honor-view-20/help/root-t3900266). https://androidhost.ru/search.html is were I got the firmware from (posted in https://forum.xda-developers.com/honor-view-20/how-to/honor-view-20-ota-march-patch-t3909075/page12). I downloaded the 9.0.1.137 firmware, since this corresponds to the one currently installed on my phone.
In summary:
I extracted recovery_ramdis.img from the update.app with the huawei extractor. In order to see this image file, I had to uncheck "verify header checksum" under settings->extract.
I then transferred this file to my phone (download folder), downloaded newest magisk manager and installed it. I then pushed INSTALL next to magisk (which was not installed of course), Install again and then Patch boot image file. Choose your transferred recovery_ramdis.img and go ahead. Transfer patched file (now called patched_boot.img) back to PC.
For the next step, bootloader has to be unlocked already! Turn on "Enable OEM unlock" and "USB debugging" in the developer options and reboot to fastboot. Open ADB as usual and connect cable to phone. Type "fastboot flash recovery_ramdisk *path to patched_boot.img*" and wait for success.
A few things to keep in mind:
-Had a bootloop with the newest version of the viper4android module!
-The root was done without custom recovery, therefore a magisk module leading to a bootloop requires you to factory reset and do everything again if you want root to work (at least i couldn't get it to work again by reflashing orginial recovery_ramdis.img followed by patched_boot.img).
-For rooting to work you have to boot phone to recovery (in this case resulting in a "normal boot"). This means pressing volume up and holding it when booting the phone. For restart you could use an app which lets you boot to recovery automatically.
-While the above my sound annoying, permanently gives you the chance to boot you phone unrooted. This is nice, especially when you have a bootloop due to a magisk module (which I had).
-According to the first link, you could install a custom recovery into the second recovery partition of Huawei/Honor devices (erecovery_ramdis). there is no official twrp available for Honor View 20 at the moment.
-After unlocking my bootloader (see post above) I had "device not verified" in google play store. After rooting, my device is verified again
Regards
garris_bibop said:
I don't know if nobody's interested or nobody wants to try rooting this phone. However, I just went ahead and tried it. I used this guide: https://topjohnwu.github.io/Magisk/install.html#emui-9 (posted in https://forum.xda-developers.com/honor-view-20/help/root-t3900266). https://androidhost.ru/search.html is were I got the firmware from (posted in https://forum.xda-developers.com/honor-view-20/how-to/honor-view-20-ota-march-patch-t3909075/page12). I downloaded the 9.0.1.137 firmware, since this corresponds to the one currently installed on my phone.
In summary:
I extracted recovery_ramdis.img from the update.app with the huawei extractor. In order to see this image file, I had to uncheck "verify header checksum" under settings->extract.
I then transferred this file to my phone (download folder), downloaded newest magisk manager and installed it. I then pushed INSTALL next to magisk (which was not installed of course), Install again and then Patch boot image file. Choose your transferred recovery_ramdis.img and go ahead. Transfer patched file (now called patched_boot.img) back to PC.
For the next step, bootloader has to be unlocked already! Turn on "Enable OEM unlock" and "USB debugging" in the developer options and reboot to fastboot. Open ADB as usual and connect cable to phone. Type "fastboot flash recovery_ramdisk *path to patched_boot.img*" and wait for success.
A few things to keep in mind:
-Had a bootloop with the newest version of the viper4android module!
-The root was done without custom recovery, therefore a magisk module leading to a bootloop requires you to factory reset and do everything again if you want root to work (at least i couldn't get it to work again by reflashing orginial recovery_ramdis.img followed by patched_boot.img).
-For rooting to work you have to boot phone to recovery (in this case resulting in a "normal boot"). This means pressing volume up and holding it when booting the phone. For restart you could use an app which lets you boot to recovery automatically.
-While the above my sound annoying, permanently gives you the chance to boot you phone unrooted. This is nice, especially when you have a bootloop due to a magisk module (which I had).
-According to the first link, you could install a custom recovery into the second recovery partition of Huawei/Honor devices (erecovery_ramdis). there is no official twrp available for Honor View 20 at the moment.
-After unlocking my bootloader (see post above) I had "device not verified" in google play store. After rooting, my device is verified again
Regards
Click to expand...
Click to collapse
Well done good job:good:
İ have chinese version PCT-AL10 9.0.1.144 right now. Do you think i can use the same way? İ wonder from which version to extract recovery_ramdis.img
I have my view20 rooted
Thanks for the instructions.
greenblueye said:
I have my view20 rooted
Thanks for the instructions.
Click to expand...
Click to collapse
You're welcome Be careful with sound improvement modules in Magisk! Had another bootloop with the Zirene module...
Which firmware did you get the recovery_ramdisk from in the end?
garris_bibop said:
You're welcome Be careful with sound improvement modules in Magisk! Had another bootloop with the Zirene module...
Which firmware did you get the recovery_ramdisk from in the end?
Click to expand...
Click to collapse
I get recovery-ramdisk from firmware PCT-AL10 9.0.1.129 . my phone is on version 9.0.1.144 but it worked:good:
After root i can not auto update software. 9.0.1.166 version is seen on ota but after download it says update is unsuccessful. Do you have any suggestion?
I think thats to be expected when rooted. Go for manual update I guess (https://forum.xda-developers.com/honor-view-20/how-to/honor-view-20-ota-march-patch-t3909075/page12). Personally I wouldn't bother with every update unless theres interesting new features and/or security updates. just to be on the safe side I would reflash the original recovery_ramdisk before updating! And backup your data!
NM Card
Hello !
Unless I'm mistaken, the View20 must be able to use nano sd cards (NM Card)