dbrand Front & Bottom Sticker with Dome TG Screen Protector - Samsung Galaxy Note 9 Accessories

Dear All Expert Users,
Have anyone of u tried using the dbrand front & bottom sticker and then applied any Temperate Glass (TG) Screen Protector on it?
Can the adhesive go accross the sticker once u applied the TG? Any bubbles exist before & after curing with UV light?

I think you'll have issues if you put a Dome on over the stickers. The dome is short of the screen at the top and bottom but it would cover the stickers and I think they would mess up the glue.

Semantics said:
I think you'll have issues if you put a Dome on over the stickers. The dome is short of the screen at the top and bottom but it would cover the stickers and I think they would mess up the glue.
Click to expand...
Click to collapse
yeah..I had the feeling it might messed up the glue also. Havent received my dome, thats why i asking either any user here had an experience with this kind of problem.

Related

Dust under delightable24 screen protector

Hi
I bought a tempered glass screen protector from delightable24 I noticed there is a little bit of dust under the protector can dust scratch the display of the note 4?
Another question in the picture you can see a place on the display which looks like air under the protector but I can't get it out it moves around when I touch it but does not get out.
And lastly I looked in amazon for this but could not find anything is the protector I bought washable?
that's not dust. it could be air. Try to lift the the screen protector from the nearest corner until you reach the air bubble, then reapply the protector again. Do not remove the whole protector...
If it is dust, then while lifting the protector, use the sticker that came with it. Just a slight touch so the dust will adhere to it, then reapply protector.
xdm9mm said:
that's not dust. it could be air. Try to lift the the screen protector from the nearest corner until you reach the air bubble, then reapply the protector again. Do not remove the whole protector...
If it is dust, then while lifting the protector, use the sticker that came with it. Just a slight touch so the dust will adhere to it, then reapply protector.
Click to expand...
Click to collapse
Already tried that but it reappears again. Could it be a defect protector ?
If you have tried the above then yes.

Does the T-mobile version come with a screen protector applied?

Does it come with one already applied to the screen or is it just a plastic wrap around the phone?
It is just thin plastic.
Dozenboy0012 said:
It is just thin plastic.
Click to expand...
Click to collapse
Mine came with a protector already applied front and rear. the plastic that was on the phone had to be taken off to put the SIM in and much to my surprise there was a screen protector already on the screen.
There's a screen protector on it under the plastic sleeve. You can tell it's there by running your hand over the front facing camera area. It's a finger print magnet tho so I took it off.
Sent from my LG-H830 using Tapatalk
Same with mine. I didn't realize it was there until I noticed the seam around the prox sensor.
I left mine on, no problem with touch responsiveness.
So?
Is it just plastic or not. I think it is. I bought a very expensive screen protector cause of the expense of the phone and it does not fit the LG G5. It also doesn't stick down at the top where it curves. Taking this back again.
[email protected] said:
Is it just plastic or not. I think it is. I bought a very expensive screen protector cause of the expense of the phone and it does not fit the LG G5. It also doesn't stick down at the top where it curves. Taking this back again.
Click to expand...
Click to collapse
Seems like it's just cheap, generic shipping-protection plastic, yeah. I had a screen protector that shipped with my case, but it also didn't stick at the top where it curves... So, it's a good thing I was just buying for the case. Now I just have to never, ever, ever drop it on that spot at the top where it curves...
so, what about applying a tempered glass protector? On top of the existing one? or remove the existing one?
I like the existing protector - it's been quite fine IMHO, and no bubbles, very smoothly applied!
John
Bigjohn_S said:
so, what about applying a tempered glass protector? On top of the existing one? or remove the existing one?
I like the existing protector - it's been quite fine IMHO, and no bubbles, very smoothly applied!
John
Click to expand...
Click to collapse
I imagine it's gonna be a pain. With that light curve at the top, you'll have to be sure you get the right protector, and even so, it might just not cover the curved part at the top. The screen protector I got wasn't glass (harder plastic) and didn't have a curve to fit, so I think it was a G4 (didn't have one, myself, just assuming it didn't have a curved top) protector that was trying to be passed off... Research, research, research first!
The protector I ordered stops just past the top edge of the 'screen, below the speaker. we'll see how that goes. It's scheduled to arrive Friday...

IMAK Glass screen protector

I just received my IMAK glass screen protector. Purchased this on AliExpress. Here are some photos of it and how I installed it. I used the 3 stickers to make a hinge after it's positioned correctly. That way I just have to remove the backing and then stick it. I'll just seperate my review into pros and cons.
Pros:
-The screen protector fits nicely. I chose this one because it has the little speaker cut out on top.
-It feels good because it is glass.
-It protects the screen well because it is glass.
Cons:
-It is glass so it has some thickness to it.
-Holds fingerprints more than screen itself
-It has a little orange peel so it's not crystal clear. You can see in the picture of the reflection of the light that it looks a little muddy instead of mirror like.
Overall, it's good for the price, but not perfect. Personally I'm back and forth between glass and film screen protectors. I'll give this a try for a few weeks and then make a final decision.
https://flic.kr/p/YVQY5o https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/YiqUeK https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/YiqRJz https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/ZgR8h3 https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/Zfqq6y https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/ZfqmJd https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/YVQPHJ https://www.flickr.com/photos/[email protected]/
Those guiding stickers are ingenious, never seen them before and the idea is just so simple and clever!!
Perfect, I know what I have to do when my phone and Nillkin protector arrive.
Thanks for sharing.
That is a lot nicer than the Riffue Tempered Glass screen protector I bought on Amazon. This one is thin and has a good height but is several mm too narrow, it doesn't even cover the LCD display let alone the entire screen/glass.
the one i order covers like half of the screen lmao wtf
just ordered one like yours.
I had one similar too this, but the dust collected over front camera under the glass.
It has some glue on it, does this IMAK one used static?
Here is a link to the one i bought.
I tried many different ones but for me this is the best.
The coating is very good against fingerprints. It fits perfect on the screen.
The sides of the screen are a little bit curved down which is good for the dust.
Updated link https://www.aliexpress.com/item/Ima...lgo_pvid=6f18e507-ed27-486a-869e-418c35f3a452
dewingerd said:
Here is a link to the one i bought.
I tried many different ones but for me this is the best.
The coating is very good against fingerprints. It fits perfect on the screen.
The sides of the screen are a little bit curved down which is good for the dust.
https://www.aliexpress.com/snapshot/0.html?spm=a2g0s.9042647.0.0.JDCsAY&orderId=87369620878335&productId=32835736602
Click to expand...
Click to collapse
The link you've sent is private, I think we can't view it.
kurtextrem said:
The link you've sent is private, I think we can't view it.
Click to expand...
Click to collapse
Try this one : https://www.aliexpress.com/item/Ima...lgo_pvid=6f18e507-ed27-486a-869e-418c35f3a452
Do it sticks in all the area? or only in borders?
Thanks
DeividMS said:
Do it sticks in all the area? or only in borders?
Thanks
Click to expand...
Click to collapse
All the area.
Got the IMAK today and it is on and I LOVE it!!
Like there is no screenprotector there at all.
Will purchase some more rightaway.
EDIT: Never seen something fit so well!!
Dust2Dust said:
Got the IMAK today and it is on and I LOVE it!!
Like there is no screenprotector there at all.
Will purchase some more rightaway.
EDIT: Never seen something fit so well!!
Click to expand...
Click to collapse
I agree, this is the best screenprotector i have ever bought. It fits perfect and the coating feels the same as on the original screen :good::good:
Just wanted to echo everyone else about how great the Imak full coverage screen protector is. I went through four different screen protectors so far (unknown brand thin plastic one, MOFI tempered glass, another MOFI tempered glass, and finally the IMAK full coverage)
The thin plastic one came bundled with the phone and would scratch if you so much as raised your voice at it. Placed it on just as a temporary protector while waiting for the others to come from Aliexpress. It just barely covered the display and left about 1.5mm of space on the edges. The phone was accidentally smacked out of my hand once and landed on a sandy floor face down, which I later discovered upon removal of the screen protector had caused a small chip on the screen near the edge, so the protector might have absorbed some of the impact.
The first MOFI tempered glass I got was a "full coverage" one, but it arrived with notches cut out on the bottom where the proximity sensor and front camera are. The worst thing about this one was that it only had adhesive on the edges, so there was a really distracting and noticeable rainbow effect (newton rings) in the middle of the screen.
The second MOFI tempered glass was also full coverage, and this time it didn't have notches at the bottom, just a hole cutout where the proximity sensor is located. The adhesive type was the same as the previous one, edge only, resulting in the newton ring effect. It also mysteriously cracked for no reason.
The one I have on currently is the IMAK full coverage screen protector. Indisputably the best out of all of them, the protector fits exactly over the entire front glass, and instead of cutout holes at the bottom, the chin at the bottom is fully glass, blackened except for where the proximity sensor and front camera are. Full adhesive all throughout means there is no rainbow effect, and the LED notification light is even tinted slightly so that it blends in with the chin, and is invisible until it turns on! The only flaw about this screen protector (yes, there is one) is that the area underneath the front camera is too thin to apply adhesive, so as a result there's a tiny gap between the glass and phone that can let in dust after a while. The dust does not seem to affect the front camera, and I never take selfies anyway, but I have yet to figure out a good way to get the dust out of there.
I have never had a screen protector fit this perfectly, even for phones other than the Mi Mix 2. Most other screen protectors have cutouts for the proximity sensor/front camera/both, but this one blends in so well that it feels like it's not even there.
Does anyone know if this protector has a dot matrix on the screen (tiny dots that reflect)? I purchased a Misha 3D protector from Amazon which looks identical to this, and it's great except for the grid of dots across the screen.
dodgyc said:
Does anyone know if this protector has a dot matrix on the screen (tiny dots that reflect)? I purchased a Misha 3D protector from Amazon which looks identical to this, and it's great except for the grid of dots across the screen.
Click to expand...
Click to collapse
When I tried it there were no dots, just very reflective and had a weird smudge pattern going on which ruined it.
The flossmall one posted elsewhere is so much better.
Lol those kind of screen protectors damn sucks, they are not full glue, so that make lot of reflections. The nillkin (regular tempered glass, full glue, no black borders), is perfect and cover all the display... So why buy this imak piece of ****?
Zedramus said:
Just wanted to echo everyone else about how great the Imak full coverage screen protector is. I went through four different screen protectors so far (unknown brand thin plastic one, MOFI tempered glass, another MOFI tempered glass, and finally the IMAK full coverage)
The thin plastic one came bundled with the phone and would scratch if you so much as raised your voice at it. Placed it on just as a temporary protector while waiting for the others to come from Aliexpress. It just barely covered the display and left about 1.5mm of space on the edges. The phone was accidentally smacked out of my hand once and landed on a sandy floor face down, which I later discovered upon removal of the screen protector had caused a small chip on the screen near the edge, so the protector might have absorbed some of the impact.
The first MOFI tempered glass I got was a "full coverage" one, but it arrived with notches cut out on the bottom where the proximity sensor and front camera are. The worst thing about this one was that it only had adhesive on the edges, so there was a really distracting and noticeable rainbow effect (newton rings) in the middle of the screen.
The second MOFI tempered glass was also full coverage, and this time it didn't have notches at the bottom, just a hole cutout where the proximity sensor is located. The adhesive type was the same as the previous one, edge only, resulting in the newton ring effect. It also mysteriously cracked for no reason.
The one I have on currently is the IMAK full coverage screen protector. Indisputably the best out of all of them, the protector fits exactly over the entire front glass, and instead of cutout holes at the bottom, the chin at the bottom is fully glass, blackened except for where the proximity sensor and front camera are. Full adhesive all throughout means there is no rainbow effect, and the LED notification light is even tinted slightly so that it blends in with the chin, and is invisible until it turns on! The only flaw about this screen protector (yes, there is one) is that the area underneath the front camera is too thin to apply adhesive, so as a result there's a tiny gap between the glass and phone that can let in dust after a while. The dust does not seem to affect the front camera, and I never take selfies anyway, but I have yet to figure out a good way to get the dust out of there.
I have never had a screen protector fit this perfectly, even for phones other than the Mi Mix 2. Most other screen protectors have cutouts for the proximity sensor/front camera/both, but this one blends in so well that it feels like it's not even there.
Click to expand...
Click to collapse
After putting the screen protector on, I take a toothpick and put some glue from a Pritt-stick in the little gap underneath the camera. Not much, just enough to close the gap. When it has dried you can color it with a black whiteboard marker if you want. When you remove the screen protector you can easily rub it off. Works great for me :good:
Thanks!
Anyone tried these?
https://www.aliexpress.com/store/pr...Front-2PCS-Back-Soft/1879465_32831400367.html
Looking to buy this phone, any new news on protectors, or is IMAK our best option?
Thanks

incipio NGP Pure Case with tempered Glass

Hi,
I've ordered last week a NGP Pure Case for my white PH1 last week. Question is : I saw on Amazon that it won't fit with tempered glasss like orzero. I don't have orzero tempered glass, I have this one : https://www.amazon.com/Essential-Sc...74582&sr=1-1&keywords=lamshaw+essential+phone that NOT covers edges.
So do you think Pure Case will be fine for me ?
Thanks for your future answers.
I think you will be fine. The case only covers a very tiny area of the screen, enough to protect it but also to lift most screen protectors. From the amazon image and the fact that I use that incipio case I am like 90% sure that screen protector wont lift
TheDethEgineer said:
I think you will be fine. The case only covers a very tiny area of the screen, enough to protect it but also to lift most screen protectors. From the amazon image and the fact that I use that incipio case I am like 90% sure that screen protector wont lift
Click to expand...
Click to collapse
You have it ? Can I have a pic plz ?
EDIT : If u want a pic of my tempered
http://reho.st/view/self/5f8cd6acb097dc6cf027725f7aabba1752b9e6de.jpg
There you go
thanks, u have a tempered ?
EDIT : Check my tempered on the link and tell me
When using this case i recommend a "Case Friendly" screen protector, tempered glass ones I have pop up around the top of the device. Just about to order https://www.amazon.com/dp/B075P1FSDX/_encoding=UTF8?coliid=I1IR0821FMR2TC&colid=3IFPSSR1GMYZN
basongwe said:
thanks, u have a tempered ?
EDIT : Check my tempered on the link and tell me
Click to expand...
Click to collapse
No, I have a skinomi screen protector
Okay, so i'm worried again... :/
Cause i've a tempered (even if it doesn't fit the corners as u can see here : http://reho.st/view/self/5f8cd6acb097dc6cf027725f7aabba1752b9e6de.jpg )
basongwe said:
Okay, so i'm worried again... :/
Cause i've a tempered (even if it doesn't fit the corners as u can see here : http://reho.st/view/self/5f8cd6acb097dc6cf027725f7aabba1752b9e6de.jpg )
Click to expand...
Click to collapse
looks like you got an all area adhesive screen protector which lifts off at the curved screen edges. Since it's already slighty lifted off at the edges I think there is no problem putting the Incipio on. The Incipio case is a problem for screen protectors which only have adhesive at the very edge, specifically at the top of the screen where the camera cutout is located. It will push and lift the adhesive off and since there is no other adhesive further down, the screen protector pretty much lifts all the way up. You then have a "clicking" sound when you tap onto that area (the adhesive will temporarily stick and then pop off when you let go).
Your screen protector is not perfectly centered and you may have small issues at the top and the bottom right where it comes close to the edge. Maybe you can re-center it.
derausgewanderte said:
looks like you got an all area adhesive screen protector which lifts off at the curved screen edges. Since it's already slighty lifted off at the edges I think there is no problem putting the Incipio on. The Incipio case is a problem for screen protectors which only have adhesive at the very edge, specifically at the top of the screen where the camera cutout is located. It will push and lift the adhesive off and since there is no other adhesive further down, the screen protector pretty much lifts all the way up. You then have a "clicking" sound when you tap onto that area (the adhesive will temporarily stick and then pop off when you let go).
Your screen protector is not perfectly centered and you may have small issues at the top and the bottom right where it comes close to the edge. Maybe you can re-center it.
Click to expand...
Click to collapse
Small issues are not a big deal, if u think I can use both ?
andril said:
When using this case i recommend a "Case Friendly" screen protector, tempered glass ones I have pop up around the top of the device. Just about to order https://www.amazon.com/dp/B075P1FSDX/_encoding=UTF8?coliid=I1IR0821FMR2TC&colid=3IFPSSR1GMYZN
Click to expand...
Click to collapse
I can vouch for this one. It fits great with my Tudia TAMM case. It's a TPU just like the Skinomi and IQ but a dry install. You peel off a small horizontal strip at the top to expose the adhesive. Position it starting at the top and then bend it a little to start separating the rest of the backing and start pushing your way down the screen so the backing comes off completely at the end. It's really grippy at first but that will pass as you use your phone. Since it is a TPU it will develop marks on it over time if you're not careful so be careful installing when trying to push out bubbles or whatever. I used a credit card wrapped in microfiber cloth and pushed out the bubbles before removing the top protective film. If you have bubbles that won't easily work out they will disappear after a few hours.
Best option so far IMO. I had the Delta Shield TPU before and the TAMM case push up the corners and edges.
Sent from my PH-1 using Tapatalk
So with my tempered, it will pop out or no ? :/
basongwe said:
So with my tempered, it will pop out or no ? :/
Click to expand...
Click to collapse
If you look at your picture your screen is already lifted off at the edges (read my previous post). So it is probably not a big deal
Hope you're right
But what do you mean by lifted ? My tempered should put off by itself with time ?
Tikerz said:
I can vouch for this one. It fits great with my Tudia TAMM case. It's a TPU just like the Skinomi and IQ but a dry install. You peel off a small horizontal strip at the top to expose the adhesive. Position it starting at the top and then bend it a little to start separating the rest of the backing and start pushing your way down the screen so the backing comes off completely at the end. It's really grippy at first but that will pass as you use your phone. Since it is a TPU it will develop marks on it over time if you're not careful so be careful installing when trying to push out bubbles or whatever. I used a credit card wrapped in microfiber cloth and pushed out the bubbles before removing the top protective film. If you have bubbles that won't easily work out they will disappear after a few hours.
Best option so far IMO. I had the Delta Shield TPU before and the TAMM case push up the corners and edges.
Sent from my PH-1 using Tapatalk
Click to expand...
Click to collapse
Looks like availability its after xmas..
Sent from my PH-1 using Tapatalk
basongwe said:
But what do you mean by lifted ? My tempered should put off by itself with time ?
Click to expand...
Click to collapse
look carefully at the picture you took. I had this with all my curved screen phones. the lighter edge you see is where the screen protector is not attached. If you have not noticed it yet then I'm afraid I just ruined your enjoyment with it.
sorry
Mine lift the tempered glass. Unless they make one a little smaller I don't think it will work.
I think I am going to just go with the Incipio case and nothing more. The screen seems more responsive.
Sent from my PH-1 using Tapatalk
Should've went with the DualPro from Incipio. I just got a black one and not only is it the highest quality case I've seen for the device but it fits just fine with Orzero TGP on.
EDIT: Felt as though I should add a caveat that applied to me, likely applies to a lot of folks having issues trying to use a case and screen protector simultaneously. You really need to nail the placement of the screen protector in order to prevent case interference, when centered as perfectly as is reasonable I have not encountered any issues with lifting but it did take two attempts to hit the sweet spot. You're much more likely to encounter lifting if the screen protector is favoring one side even slightly, so those guide stickers that you tend to want to chuck actually come in very handy when trying to get the placement just right.

Micro Scratches

Does anyone have suggestions for how to remove micro searches from the screen? I've heard mixed things about using toothpaste and am wondering if anyone one else has had experience in this area
abduljaz7 said:
Does anyone have suggestions for how to remove micro searches from the screen? I've heard mixed things about using toothpaste and am wondering if anyone one else has had experience in this area
Click to expand...
Click to collapse
DONT use tooth paste. It's just jerks lying for YouTube hits. You may being noticing just scratches on the oleophopic coating. You can't fix that. If you can feel the scratches with your nail the you can polish them out but you will remove more oleophobic Coating. My advice put a screen protector on and forget about it or ask OnePlus to replace screen if you want perfection .
Just apply a uv tempered glass and leave it that way.
The Power of Oneplus 7 Pro be with you
As advised above, LOCA (Liquid optically clear adhesive) is apparently good for hiding micro-scratches so applying a UV Glue screen protector will probably help and avoid future damage. The Whitestone Dome protector would most likely be the best candidate although it is pricey but has tons of good reviews.
Hello Is there any glue left stick with screen when this type of protector is removed?
RISHI RAJ said:
Hello Is there any glue left stick with screen when this type of protector is removed?
Click to expand...
Click to collapse
No. Comes off like any other glass protecor
johnnyman25 said:
Just apply a uv tempered glass and leave it that way.
The Power of Oneplus 7 Pro be with you
Click to expand...
Click to collapse
I agree. Apply one of those uv svreen protectors and the glue will fill those scratches and make them invisible, and also those screen protectors look the best.
I picked up one of these and couldn't be happier WELL worth the $$
Oneplus 7 Pro Tempered Glass Screen Protector,Fingerprint Scaner 3D Liquid Transparent Clear Full Curved Edge Case Friendly Anti-Scratch Coverage for Oneplus 7 Pro 2019-2 Pack https://www.amazon.com/dp/B07RRVMX2Z/ref=cm_sw_r_sms_apa_i_y70hDbKMKCN1X
There is one for 4$ in AliExpress
Thanks for the tips.

Categories

Resources