was about to install a new viper rom 6.0.0 from TWRP and when completed it was not booting. so i restored my back up and now i'm getting a fail "failed to mount data(no such process)". installed a the original viper rom and now its showing decryption unsuccessful after the phone boots
Related
I am flashing OmniROM-4.4.2 for my Huawei Ascend P1 using Philz Touch Recovery based on cwm 6.0.3.7.. I did it successfully once, created a backup and got back to my old liquidsmooth rom by Spanorg so that I could do a proper backup of my files to transfer it to the new rom. However, upon wiping everything, now everytime I try to flash the OmniROM-4.4.2, it says 'set_perm some changes failed status 7 installation aborted'.. I have the backups, but it says they have md5 checksum mismatched.. and when i try to go into my old rom, it gets stuck in the boot loop..
I have tried clean installing a couple of times, but nothing seems to work..
Any fixes, guys?
I've just finished flashing the stock motorola 4.4.4 EU rom and updating it after using CM 12 and having it become very unstable on my device due to the recent nightlies. I downloaded the official ota update to 5.0.2 the system reboots into TWRP (Version 2.8.5.0) and displays:
E: Error executing updater binary in zip '/cache/Blur_Version.210.12.40.falcon_umts. EURetail.en.EU.zip;
E: Error installing zip file '/cache/Blur_Version.210.12.40.falcon_umts.EURetail.en.EU.zip'
As soon as i select reboot into system, the boot loads fine and stays on for a while, but then automatically restarts to attempt the install again. Im assuming this error is because I'm running a custom recovery, but any help would be great! I know exactly where the zip is on my phone storage too, so would it be a matter of installing manual (however when I checked it displayed a message saying it could be incompatible and render my device unstable, and I really dont want to have to reinstall the rom again.
Also I have not updated to a custom boot loader, its running the kitkat boot loader from motorola.
Thanks in advance
My system is now KK 4.4.2 with unlocked bootloader
I download CM12 (nightly) from download.cyanogenmod.com - XT925 KK bootloader
I intended to install CM12.zip via Phil Touch recovery but it failed and this message appeared:
This package is for device: xt925, vanquish_u; this device is .
E: Error in /storage/sdcard1/....CM12.zip
(Status 7)
Installation aborted.
Then I used TWRP recovery instead of CWM.
The installation was successful, but in a short time (faster than installing gapps)
I made the phone rebooted.
When the system was on, it showed an error dialogue and self-rebooted to boot animation graphics immediately. Then, it became an endless loop
I had to reflash stock KK system via RSD
What happenned to my XT925????
Try flashing CM11, factory reset, then CM12 nightly dirty flash. That way I got it to work. You need to remove the first line "assert..." in a file inside the zip to make it work with philz. Normal install or update of CM12 nightly works only with current cyanogen recovery for me.
The problem is the gapps file
I've only installed the CM rom via TWRP and the system is now running without gapps
Yes you need gapps for 5.1, best from the CM wiki
I've TWRP 2.8.7.0 installed on my OPO 64 GB running rooted CS12.0-YNG1TAS2I3. I found the multirom thread "http://forum.xda-developers.com/oneplus-one/development/mod-multirom-v26-t2835738" and flashed it on my phone just for fun.Two weeks earlier when I tried installing OnePlus provided AOSP stock "https://forums.oneplus.net/threads/rom-official-4-4-4-oneplus-aosp.65482/" it gave some error about rom built for older build and I forget about it. Recently I wiped my "data" , "system" , "cache" and "dalvik" and tried to installing AOSP zip again but it gave me error saying updater binary error. I tried installinging "cm-12.0-YNG1TAS17L-bacon-signed.zip" and "cm-12.0-YNG1TAS2I3-bacon-signed.zip" ,downloaded from official website of course, and got the same error. I went back to multirom thread and installed "MultiROM uninstaller" zip and it worked perfectly fine but when I again tried installinging "cm-12.0-YNG1TAS17L-bacon-signed.zip" and "cm-12.0-YNG1TAS2I3-bacon-signed.zip" still the same error. I Google(d) about it and downloaded and flashed "twrp-2.8.0.1-bacon.img" from "https://dl.twrp.me/bacon/twrp-2.8.0.1-bacon.img" using fastboot flash recovery twrp-2.8.0.1.img and tried installing zip from that recovery,same error. Then I repeated process with twrp-2.8.7.0 and still same error. Incidentally I'd good sense of creating backup before erasing all partitions and TWRP had no problem restoring it and for now my phone is up and running. Any ideas why I might be getting those errors?
I also pulled out boot.img from "cm-12.0-YNG1TAS2I3-bacon-signed.zip" and flashed it through fastboot,still TWRP giving the same error
was about to install a new viper rom 6.0.0 from TWRP and when completed it was not booting. so i restored my back up and now i'm getting a "failed to mount data(no such process)". installed the original viper rom and now its showing decryption unsuccessful after the phone boots.