when I flashed it with TWRP, my phone do not waked up again. Instead it shows black screen with blue light.
The blue light shows only when I put SD Card inside and I put the card outside and try to reboot, then phone is completly dead without any light.
My PC detects my phone only when SD Card is inside and is detected as Qualcomm HS - USB Diagnostic 9006.
HOW I CAN SOLVED IT
Related
So I've got a Sensation phone that won't start. Bootloader menu can't be accessed as well. When I plug it in, the orange LED lights up, stays on for about 3 seconds, then goes off for about a second and finally lights up again and stays on permanently. Tried with a different battery - no luck. When I connect it to the pc via micro usb cable, the computer recognizes the phone (installs drivers for htc sensation). And there's something more - when I connect the charger in a completely dark room, the display backlight becomes visible. The screen doesn't light up but it also doesn't remain completely dark. It's like the screen is on but completely black.
So what can I do? Thought that the power button might be defective, so I removed the black tape over the button and short circuited the two small pins on top of the button. It didn't work. I can't fire it up through abd, because usb debugging is off. So do I have any options beside selling it on ebay or giving to a service technician?
Hi
Greetings
try this it might be your last option
http://forum.xda-developers.com/showthread.php?t=1522351
Thanks for the suggestion
I haven't tried this solution yet because the problem does't seem to be a QHSUSB_DLOAD issue.
Upon connection with pc it identifies with hardware id USB\VID_0BB4&PID_0FF9&REV_0228 as a mass storage device...
Hi all
I have an huawei g6-u10 from my friend, he told me that was at school the phone was powered off (by him); when he returned from school, he tryed to power on the phone but it wont start.
Now i have it in my hands and i can confirm it
the phone seems on, if i press once power button green led appear (for a sec)
but the screen is black, completly dead
if i try to push vol down and power off for 15sec it vibs twice and then nothing, again screen black, anything
if i connect the phone to the pc it start automatically Media Partners, so i cant have access to sd card or internal memory
if i digit "adb devices" from c:/adb there are two blank lines and no phone show up
if i go to the device manager in windows, when i connect the phone to the pc it shows two partition with "portable devices" label, named F: and G:
How i can fix it?
Thanks to all
regards
water damage.
I got a new screen module, a new battery, same ish though.
So if I plug it into the wall, or a portable battery charger, it starts to load, red charging LED comes on, and the screen comes on with SONY and then it shuts off and does it again. It's about a 2-3 second loop continuous.
If I plug it into my computer, the red led will either flash once and nothing happens, just one flash.. then another flash etc
or it will flash three times and again nothing happens, it just does that repetitively.
I can't seem to boot into safe mode. Even with PC Companion. I have tried pressing the OFF switch next to SIM and SD slot. Which both are empty.
Turning to you, XDA. Any ideas?
I replaced the LCD on my phone and now I'm stuck in some sort of loop. It goes to the boot screen then powers off then repeats over and over again. I can't get it to boot into recovery nor can I get it to be recognized by my computer. I tried putting a Dload folder on a 32gb SD. And still nothing. Any suggestions would be great.
Maybe you shorted something or broke a trace? i'd say, open your phone and look around with something like a magnifying glass. If that doesnt work, can you get in fastboot mode without the phone shutting off? (plug the phone into a pc or laptop via usb and power+volume down)
Hi
I have a u11.
last week while i was working with my phone suddenly it hanged and i tried to soft reset.
after that phone showed me blackscreen and nothing happened even i connect phone to the charger and charging led not showing and phone cant power on.
i tried a lot of methods with power and volume buttons but they didnt work.
when i connect phone to the pc it shows qusb_bulk driver or qualcomm hs-usb qdloader 9008
What happened and what can i do?
thanks
same problems
wait for helps
Hi,
I had the exact same problem:
HTC U11 just dropped dead in the middle of a phone call
- Would not turn on again.
- Would not soft-reset (pressing volumeLow + Power button for 10 secs makes the phone vibrate and the screen backlight turn on but the screen remains black).
- Would not charge (screen stays black).
- When connected to a Win10 PC via USB, it is detected as 'qusb_bulk' but no drive is shown
SOLUTION:
I removed the Sim card (not sure if this is even necessary).
Then I opened the phone (see tutorials on youtube etc) and disconnected the battery, then pressed the Power-button (just to make sure the remaining energy is drained). Then reconnect the battery and: it turns on just fine!
cbie said:
Hi,
I had the exact same problem:
HTC U11 just dropped dead in the middle of a phone call
- Would not turn on again.
- Would not soft-reset (pressing volumeLow + Power button for 10 secs makes the phone vibrate and the screen backlight turn on but the screen remains black).
- Would not charge (screen stays black).
- When connected to a Win10 PC via USB, it is detected as 'qusb_bulk' but no drive is shown
SOLUTION:
I removed the Sim card (not sure if this is even necessary).
Then I opened the phone (see tutorials on youtube etc) and disconnected the battery, then pressed the Power-button (just to make sure the remaining energy is drained). Then reconnect the battery and: it turns on just fine!
Click to expand...
Click to collapse
Nothing will happen with this solution, ur problem was different u could just reconnect the battery and ur issue would have been fixed