Mods, please move/remove this if its in the wrong area.
I updated to Oreo via OTA on my G930T. It rebooted just fine. After I used it for awhile, my phone got super hot so I decided to power it down. I turned it back on and it would only get to the Galaxy S7 splash screen and no where else. I tried factory resetting and wiping cache via recovery and flashing the stock firmware again in Odin.
When I tried to flash in Odin, I tried Oreo and Nougat and this error comes up on the Download Mode screen: "Unsupport dev_type." I made sure that I had the right firmware. The File said SM-G930T and my phone says SM-G930T on the back and in Download Mode. I even reinstalled drivers and opened odin in both admin mode and normal mode.
I should also add that in recovery it says at the following:
#fail to open recovery_cause(No such file or directory)#
#Reboot Recovery Cause is [UNKNOWN]#
No Support SINGLE-SKU
Any ideas? I'm at a complete loss.
EDIT: Here's the log in Odin after I hit start:
<ID:0/007> Odin engine v(ID:3.1207)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> emmc_appsboot.mbn.lz4
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
try get regular Odin 3.13 version. i had same error when i used odin 3.12 patched one.
Related
So I softbricked my phone by messing up during rooting it with Odin.
Now when I try to stock flash using Odin, this error shows up
<ID:0/007> Odin engine v(ID:3.1203)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The firmware is correct, it's SM-G920W8 from Bell, it's the latest version of Odin, and I've tried so many things but it just says FAIL each time.
When I exit download mode, via battery pull, it the booting screen starts up, then it just goes black. Additionally, in the top left corner, it says: Kernel is not Seandroid reinforcing.
Smartswitch also doesnt work as the emergency function wont recognize my phone
Thanks
Ok,
So I am trying to fix my dads phone which stopped working over the weekend and am at a total loss. The phone will ONLY boot into odin download mode. You can turn it on normally, can't get into recovery mode. I have already tried to flash the lastest stock TAR via odin and it installs fine, except nothing changes, still no recovery or boot.
OS I installed: G920PVPS4DQE2_G920PSPT4DQE2_G920PVPS4DQE2_HOME.tar .md5
ODIN Report
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> cache.img
<ID:0/007> modem.bin
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Removed!!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Have tried Vol - & Power to simulate battery pull and then quickly pressing Vol + & Power to enter recovery ? A customer gave me an G920P too with the same problem but wasnt able to boot in anyway, i believe G92XP firmwares are bad in some way
Nope, can only get into ODIN. Repetedly went into ODIN mode and completely drained the battery and then did a full charge, still nothing.
Iv tried Odin with all Bl,AP,CP, and CSC Packages it keeps saying FAIL! (Auth) then a blank log then Complete(Write) operation failed.
For the Samsung smart switch the phone us supported. I have the latest verison and my phone is a Galaxy S7 (Us Cellular) Model: SM-G930R4 still says its not supported.
Im stuck idk what to do and i just want my phone working again! Thank you for the help!
Update: Phone wont enter Recovery Mode nor will start just download mode.
Update: got in to show me i need smart switch recovery. Its says my device is not supported and when i try to recovery feature my phone doesn't appear.
When I apply all BL,Ap ect. It shows
SW REC CHECK FAIL: [aboot]Fused 4 > binary 2
[1] eMMC: write Fail: aboot
When just flashing the AP with odin these are the logs
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Its stuck in on the screen telling me to use smart switch pc software
Wont start to boot or go to recovery.
Tried odin start with re-partion and these are the logs farthest i gotten with no errors popping up on my phone
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> persist.img.ext4
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 1831)
<OSM> All threads completed. (succeed 0 / failed 1)
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
*Detection* said:
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
Click to expand...
Click to collapse
I have been using the modded one this entire time does that mean anything?
*Detection* said:
Try using the modded "Prince Cosmy Odin" with stock firmware first
If that fails, try following this
https://forum.xda-developers.com/galaxy-s7/how-to/unbrick-s7-snapdragon-trying-to-to-t3697441
Click to expand...
Click to collapse
I attempted to follow that link so i when through the steps came to step two of downloads and had to find a S7 Snapdragon Root .tar so i did and found this XDA forum https://forum.xda-developers.com/verizon-s7-edge/how-to/root-method-nougat-t3566978 which was the first thing on google searching for the snapdragon.
I followed those steps and i for the error Secure check fail : Boot
I was also able to get it to get into a boot loop once again
When i run odin with the S7_Qualcomm.tar with auto reboot re-partition f. reset time and nand earse all it fails and gives me these logs
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Erase...
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Can't open the specified file. (Line: 1831)
<OSM> All threads completed. (succeed 0 / failed 1)
When running the s7_qualcomm.tar file with only auto reboot and r.reset time I get a PASS with these logs
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
But now my phone is in a boot loop with the logo of samsung S7 and the reovery booting.. is also popping up at the same time.
Enisty said:
I have been using the modded one this entire time does that mean anything?
Click to expand...
Click to collapse
Have you tried the non-modded version?
I'd have used that first
ODIN 3.12.3 or newer
*Detection* said:
Have you tried the non-modded version?
I'd have used that first
ODIN 3.12.3 or newer
Click to expand...
Click to collapse
IT WORKS!
I downloaded this file
USC-G930R4TYU4BQK3-20171221083318.zip
Wish I knew where I got it from but now my phone is actually turning on!
There was a loading screen iv never seen before thought it show
Installing applications with a black bar then smart switch popped up and the bar was filled instantly with yellow lol iv just never seen this screen before from
past uses of any Samsung device.
Good stuff, just be cautious with that model S7, it's a snapdragon meaning much more difficult to unbrick if you brick it as the bootloader is locked
*Detection* said:
Good stuff, just be cautious with that model S7, it's a snapdragon meaning much more difficult to unbrick if you brick it as the bootloader is locked
Click to expand...
Click to collapse
Its really buggy the OS itself. Its slower the normal idk if its just because of how fresh it is like the flash maybe just give it time?
Enisty said:
Its really buggy the OS itself. Its slower the normal idk if its just because of how fresh it is like the flash maybe just give it time?
Click to expand...
Click to collapse
Did you factory reset after the flash (or use CSC to force the reset)?
I'd reset it, it should be pretty smooth after maybe 5 mins of first boot
So, I tried to root an s8+ SM G955F. I guess I didn't take some measures and triggered the Knox security.
I tried to make something work from safe mode and wanted to uninstall TWRP app. After that I got hit by the \only official released binaries are allowed to be flashed\ message every time i tried to boot. I can go to download mode only.
I try to flash stock firmware via Odin and it says fail. Here is the log:
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> up_param.bin
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone help me?
Shadοw Force said:
So, I tried to root an s8+ SM G955F. I guess I didn't take some measures and triggered the Knox security.
I tried to make something work from safe mode and wanted to uninstall TWRP app. After that I got hit by the \only official released binaries are allowed to be flashed\ message every time i tried to boot. I can go to download mode only.
I try to flash stock firmware via Odin and it says fail. Here is the log:
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> up_param.bin
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Can someone help me?
Click to expand...
Click to collapse
Might need more information like:
Current firmware?
Firmware trying to flash?
Odin version?
Could be wrong but sounds like flashing wrong or downgraded firmware.
Im trying to update my phone using odin but this happened:
Code:
<ID:0/007> Odin engine v(ID:3.1401)..
<ID:0/007> File analysis..
<ID:0/007> skip file list for home binary
<ID:0/007> param.bin
<ID:0/007> userdata.img
<ID:0/007> Home Binary Download
<ID:0/007> Total Binary size: 5608 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> preloader.img
<ID:0/007> lk-verified.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried to restart the flash but now its only this:
Code:
<ID:0/007> Odin engine v(ID:3.1401)..
<ID:0/007> File analysis..
<ID:0/007> skip file list for home binary
<ID:0/007> param.bin
<ID:0/007> userdata.img
<ID:0/007> Home Binary Download
<ID:0/007> Total Binary size: 5608 M
<ID:0/007> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
UPDATE:
discovered that i can still boot to download mode after all of that, but i still cant flash it (its still stuck as of now)
UPDATE:
turns out you only need the patched odin 14.1 here and try to flash again, although i only tried to reflash BL of the same firmware, no updates
DEVICE INFORMATION:
Samsung Galaxy A12 (SM-A125F XTC)
The Recent Firmware Flashed: A125FXXU2CVH1
The Firmware i tried to flash: A125FXXU2CWB1
you figured it out? or still need help?
TheWorldYT said:
you figured it out? or still need help?
Click to expand...
Click to collapse
slightly, i think something is still broken since the stock file manager is refusing to open