Related
Ok so I purchased a used hox on craigslist the other day. When I first put my sim card in after purchase I was unable to get a data connection using the pta apn. I had network connection and was able to make/receive calls and texts, but had no data connection. I was getting the "misconfigured apn" error in network settings. After some googling I found that I need to switch my plan to an att LTE plan (I am in a covered area). I am not the account holder, and it would be a day or two until I could get in contact with the account holder, so I just threw in the wap.cingular or phone apn and was able to get an hspa connection fine. So I rooted the phone and unlocked the bootloader (using htc dev) without a problem, flashed a few custom roms, everything is working 100%. Except for last night when I finally decided to switch my plan over with AT&T and try to connect to LTE. After about an hour on the phone with technical support, they concluded that I don't have an AT&T phone, which I am certain I do.
I am guessing that the only way they could tell that I didn't have an AT&T phone was from the IMEI which they asked for at the beginning of the call. So I checked the IMEI on the box against the IMEI on the phone and they are different. The SNs match, but the IMEIs are different. I checked out the phone IMEI online and it came back as invalid. (For the record I also checked the box IMEI against the lost and stolen phone database and it was not found)
So, basically, I am wondering if this issue can be caused by something that I did (ie rooting, bootloader unlock, rom flashing, etc) or if I was somehow sold a tampered device or if this is something to be concerned about. Its not a very big deal if its something I did, I understand the risks associated with rooting/unlocking/flashing etc.
henchdiesel said:
Ok so I purchased a used hox on craigslist the other day. When I first put my sim card in after purchase I was unable to get a data connection using the pta apn. I had network connection and was able to make/receive calls and texts, but had no data connection. I was getting the "misconfigured apn" error in network settings. After some googling I found that I need to switch my plan to an att LTE plan (I am in a covered area). I am not the account holder, and it would be a day or two until I could get in contact with the account holder, so I just threw in the wap.cingular or phone apn and was able to get an hspa connection fine. So I rooted the phone and unlocked the bootloader (using htc dev) without a problem, flashed a few custom roms, everything is working 100%. Except for last night when I finally decided to switch my plan over with AT&T and try to connect to LTE. After about an hour on the phone with technical support, they concluded that I don't have an AT&T phone, which I am certain I do.
I am guessing that the only way they could tell that I didn't have an AT&T phone was from the IMEI which they asked for at the beginning of the call. So I checked the IMEI on the box against the IMEI on the phone and they are different. The SNs match, but the IMEIs are different. I checked out the phone IMEI online and it came back as invalid. (For the record I also checked the box IMEI against the lost and stolen phone database and it was not found)
So, basically, I am wondering if this issue can be caused by something that I did (ie rooting, bootloader unlock, rom flashing, etc) or if I was somehow sold a tampered device or if this is something to be concerned about. Its not a very big deal if its something I did, I understand the risks associated with rooting/unlocking/flashing etc.
Click to expand...
Click to collapse
what method did you use to unlock the bootloader? If you used the one without HTCDev found here http://forum.xda-developers.com/showthread.php?t=1734558 it changed the IMEI number. You can put it back though.
gunnyman said:
what method did you use to unlock the bootloader? If you used the one without HTCDev found here http://forum.xda-developers.com/showthread.php?t=1734558 it changed the IMEI number. You can put it back though.
Click to expand...
Click to collapse
I actually used the method outlined here, http://forum.xda-developers.com/showthread.php?t=1671396, which is probably a similar method under the hood I guess. How would I go about returning the IMEI to stock? Is it as simple as opening mmcblk0p4 in a hex editor and changing the 11111111 back to CWS__001?
henchdiesel said:
I actually used the method outlined here, http://forum.xda-developers.com/showthread.php?t=1671396, which is probably a similar method under the hood I guess. How would I go about returning the IMEI to stock? Is it as simple as opening mmcblk0p4 in a hex editor and changing the 11111111 back to CWS__001?
Click to expand...
Click to collapse
Nope.
the method you used doesn't TOUCH IMEI. IMEI and CID are two different things.
did you happen to notice when you got the phone if the bootloader said locked? or was it re-locked?
I suspect if it's the latter then whoever had the phone before you did used the "without htc dev" method to unlock and didn't copy back the unaltered partition when they were done.
There are ways to rewrite the correct IMEI to the phone. I don't know how, and discussion of it is forbidden here. Maybe someone who can help you will send you a PM.
gunnyman said:
Nope.
the method you used doesn't TOUCH IMEI. IMEI and CID are two different things.
did you happen to notice when you got the phone if the bootloader said locked? or was it re-locked?
I suspect if it's the latter then whoever had the phone before you did used the "without htc dev" method to unlock and didn't copy back the unaltered partition when they were done.
There are ways to rewrite the correct IMEI to the phone. I don't know how, and discussion of it is forbidden here. Maybe someone who can help you will send you a PM.
Click to expand...
Click to collapse
The phone did say locked when I got it. It may have been re-locked, but there is no way for me to be sure. I guess if anyone has info about repairing my IMEI and could pm me I'd really appreciate it. Otherwise I guess I'm out of luck. Thank you very much for your help.
henchdiesel said:
The phone did say locked when I got it. It may have been re-locked, but there is no way for me to be sure. I guess if anyone has info about repairing my IMEI and could pm me I'd really appreciate it. Otherwise I guess I'm out of luck. Thank you very much for your help.
Click to expand...
Click to collapse
if it said LOCKED then IMEI got corrupted by some other means. Sorry I can't be of more help. I do have a suggestion though.
Find one of those Cell phone stores that advertises flashing phones to some other carrier. Maybe THEY have the means to fix your IMEI.
gunnyman said:
if it said LOCKED then IMEI got corrupted by some other means. Sorry I can't be of more help. I do have a suggestion though.
Find one of those Cell phone stores that advertises flashing phones to some other carrier. Maybe THEY have the means to fix your IMEI.
Click to expand...
Click to collapse
I'm just glad it was something that I screwed up as opposed to my buying a tampered/stolen device. Mods can probably close this thread, mark it as "solved" or something like that, before we get too far into the IMEI modding stuff. Hopefully I can get this figured out on my own. Thanks again for your help.
Hit me on gtalk. Ill get u fixed up seriously tho. Pmed
Sent from my SPH-L710 using xda premium
It's likely not an IMEI issue....but more likely you don't have an LTE SIM. Symptoms are just that.
Op said the Imei numbers between phone and box don't match up
Sent from my HTC One X using xda premium
18th.abn said:
Hit me on gtalk. Ill get u fixed up seriously tho. Pmed
Sent from my SPH-L710 using xda premium
Click to expand...
Click to collapse
best person to contact for your issue...
not a big deal...if you have the stick on the back on the phone or the box
imei, sn, mb....you good...
[I'd like to create a thread to collect information for all variants of the R530. I'll update this first post with additional information people give during discussion. Sorry it is here in the Verizon sub, but this is the closest model]
The SCH-R530 is a special flavor of the Samsung Galaxy S3 with sub-favors: (you should probably puke now)
SCH-R530U is a US Cellular variant
SCH-R530C is a Cricket variant
SCH-R530M is a MetroPCS variant
SCH-R530X is a Generic variant
I suspect these are all the same hardware, but just different ROMs. I would like to confirm this.
I would like to know and post the newest firmware versions for each. (at least the names, if not the ROM files themselves) I'd like to know if ROMs are compatible, if modem firmwares are compatible, if bootloaders are compatible. The small community of owners need to pull together as much as possible.
Model -- Hardware Version / Firmware Versions / Baseband
SCH-R530U --
SCH-R530C --
SCH-R530M --
SCH-R530X -- R530X.01 / JSS15J.R530XWWUBMK4 / R530XWWUBMK4
Please post if you can add to this information!
I'm working on my dad's SCH-R530X (Generic CDMA). It was on a regional CDMA provider that he was not happy with -- he paid $500 to them in January for the phone. Edit: Today, he's on PagePlus, but without data for some reason.
Concerns (that someone may be able to help me with):
Once you go to KK 4.4 you can not go back? Your bootloader is updated and will not boot 4.3?
I'm running 4.3, can I root -> replace recovery -> custom ROM ... without tripping the KNOX warranty void? I've read that saferoot will not trip KNOX?
This phone seems to have an odd Call Audio Quality problem. While listening during a phone call (on the R530), the other party's voice cuts out. Specifically, it cuts out when the other person isn't speaking in their mic close enough or loud enough. It's as if the R530 is filtering out anything under a certain volume level. I've turned off Call Equalizer and Noise Reduction to try to solve this problem. I believe I've read people say a firmware/ROM update from US Cellular fixed this problem.
So you can see, I have some constraints: Still in warranty and don't want to void it by tripping KNOX. Want to try a newer firmware for call audio problem. Don't want to brick phone with incompatible firmware, unless US Cellular will work on this X/Generic phone.
Help would be appreciated.
I do have the USC and Cricket variants but the USC version is soft bricked.
HW: R530C.01
Firmware: JSS15J.R530CVVUCMK3
Baseband: R530CVVUCMK3
Also fyi, this and the USC version requires a sim card.
motoyola said:
I do have the USC and Cricket variants but the USC version is soft bricked.
HW: R530C.01
Firmware: JSS15J.R530CVVUCMK3
Baseband: R530CVVUCMK3
Also fyi, this and the USC version requires a sim card.
Click to expand...
Click to collapse
Thanks... I'll add the info. I think I'll make a spot to record if it has a SIM slot too -- as my 530X does not have a SIM slot and was labeled with a little sticker "3G CDMA"... but the MEID starts with a "9" and LTE visible in DFS.
syserr said:
Thanks... I'll add the info. I think I'll make a spot to record if it has a SIM slot too -- as my 530X does not have a SIM slot and was labeled with a little sticker "3G CDMA"... but the MEID starts with a "9" and LTE visible in DFS.
Click to expand...
Click to collapse
I have a regional version of the s3 as well, d2xar (sch-r530x) on Inland Cellular, primarily based in the north west US. as far as i can tell, i havent dissasembled my phone to see if there is a lte radio, in the original build.prop for my phone it is disabled on boot so it will not consume power since it is not being used. thus the 3g cdma only sticker. for the us cellular version i do not know if there is a kitkat firmware but if there is there is always the possiblity you will not beable to go back. as for the generic version it is only on 4.3 right now. eitherway the higher the bootloader version is better for customroms due to recoveries and features working better. as for saferoot i dont remember if it trips the warranty bit or not since ive long since written a custom recover to the device which tripped it but i do know itll make the stock rom list itself as custom in the settings after being rooted. also something to keep in mind with a custom rom is, unless you have the apns for your carrier eg, pageplus, usc, ect. you will not have mms capabilities. Im still tearing my build.prop and apn back up apart to see if i can include some of that info into a custom rom to fix mms, or a recovery that will inject it after a rom flash.
Update?
Lrs121 said:
I have a regional version of the s3 as well, d2xar (sch-r530x) on Inland Cellular, primarily based in the north west US. as far as i can tell, i havent dissasembled my phone to see if there is a lte radio, in the original build.prop for my phone it is disabled on boot so it will not consume power since it is not being used. thus the 3g cdma only sticker. for the us cellular version i do not know if there is a kitkat firmware but if there is there is always the possiblity you will not beable to go back. as for the generic version it is only on 4.3 right now. eitherway the higher the bootloader version is better for customroms due to recoveries and features working better. as for saferoot i dont remember if it trips the warranty bit or not since ive long since written a custom recover to the device which tripped it but i do know itll make the stock rom list itself as custom in the settings after being rooted. also something to keep in mind with a custom rom is, unless you have the apns for your carrier eg, pageplus, usc, ect. you will not have mms capabilities. Im still tearing my build.prop and apn back up apart to see if i can include some of that info into a custom rom to fix mms, or a recovery that will inject it after a rom flash.
Click to expand...
Click to collapse
Any update to this? I have the sticker too and it'd be great to have LTE on since this phone supports it, it seems. I've made this post
http://forum.xda-developers.com/galaxy-s3/general/s3-d2xar-cdma-how-to-set-straight-talk-t3012846
uplusion23 said:
Any update to this? I have the sticker too and it'd be great to have LTE on since this phone supports it, it seems. I've made this post
http://forum.xda-developers.com/galaxy-s3/general/s3-d2xar-cdma-how-to-set-straight-talk-t3012846
Click to expand...
Click to collapse
Last I checked there was a bug with the d2lte builds that break the ability to set apns... I made a cm10.2, I think, build that allowed changing the APN. Um if I remember right the physical design of the d2xar has hardware similar to the Verizon s3. I still don't know if there is an lte modem in the phone since there doesnt seem to be a sim card slot, though there maybe an integrated uicc. I haven't played with it much since I switched to using my nexus 5 on T-Mobile.
Lrs121 said:
Last I checked there was a bug with the d2lte builds that break the ability to set apns... I made a cm10.2, I think, build that allowed changing the APN. Um if I remember right the physical design of the d2xar has hardware similar to the Verizon s3. I still don't know if there is an lte modem in the phone since there doesnt seem to be a sim card slot, though there maybe an integrated uicc. I haven't played with it much since I switched to using my nexus 5 on T-Mobile.
Click to expand...
Click to collapse
I got to the service mode settings, which oddly enough it listed GSM and CDMA. Quite weird. To get there was even weirder. Sadly the D2xar doesn't support TWRP Recovery, and the only one that works is CWM by Philz.
uplusion23 said:
I got to the service mode settings, which oddly enough it listed GSM and CDMA. Quite weird. To get there was even weirder. Sadly the D2xar doesn't support TWRP Recovery, and the only one that works is CWM by Philz.
Click to expand...
Click to collapse
Yah I noticed that to when I was digging around for apns for my old carrier. As for twrp I got around that problem by building my own version using cyanogenmod and the d2lte device files. It made cyanogenmod delta updates possible on the d2lte build. Which are really nice. My source is floating around github, though you'd have to do a little digging to find everything. I do have precompiled twrp images on my webserver that I try to keep up to date for my friend who's brother has the same phone. If you go to my site its safe to ignore the certificate warnings, I have it set to force HTTPS and the reason the warning pops up is because I self signed it instead of paying for a company like verisign
Sorry for my superbly late reply. I've done a ton of digging with this phone. Turns out it only supports Evdo. So no LTE sadly. Even worse, using the Test Menu I can't bands to USA bands, only the (800 or 850?) Hz Global band. I can't get a connection. Well. The bars are listed as 2-3 generally, but it says "Roaming Indicator Off". I have the latest and only baseband, too.
(Wow. After two months of fiddling, as of typing this, I turned on cellular service, which is usually in Airplane mode, I got a " 3G" connection for the first time. Only for a second.)
I don't think I'll be able to switch this over to Straight Talk any time soon, though. I'll check your GitHub soon for that TWRP.
---------- Post added at 11:00 AM ---------- Previous post was at 10:49 AM ----------
uplusion23 said:
Sorry for my superbly late reply. I've done a ton of digging with this phone. Turns out it only supports Evdo. So no LTE sadly. Even worse, using the Test Menu I can't bands to USA bands, only the (800 or 850?) Hz Global band. I can't get a connection. Well. The bars are listed as 2-3 generally, but it says "Roaming Indicator Off". I have the latest and only baseband, too.
(Wow. After two months of fiddling, as of typing this, I turned on cellular service, which is usually in Airplane mode, I got a " 3G" connection for the first time. Only for a second.)
I don't think I'll be able to switch this over to Straight Talk any time soon, though. I'll check your GitHub soon for that TWRP.
Click to expand...
Click to collapse
Yeah, just of now I've been unable to re-acquire the "3G" that caused me to have a boost of hope. Now even when I attempt calling which it usually would bring me to the Verizon automated system, asking to make a collect call, since around here is primarily Verizon, I can't even get it to call. It now states that no mobile network is available, even when I have 2-3 bars.
You have no "3g" because your keys are wrong. Y'all need some QPST and see the whole logon process and baseband messages. Then you can really troubleshoot your phone.
I have a Verizon Samsung Galaxy S3 on the Straight Talk network. I check for software updates and it tells me the software is up to date however it says my phone is running off of 4.4.2 instead of the Lollipop or the one just under. Does anyone know if Lollipop 5.0 or 5.1 has reached the S3 yet? Or how to manually update my phone software so its not so low?
flash a custom rom with 5.x for your model.
nxb said:
flash a custom rom with 5.x for your model.
Click to expand...
Click to collapse
Phone is not rooted so how do I do that? I need or to be updated. My phone doesnt work right on 4.4.2
Sent from my SCH-I535 using XDA Free mobile app
you will have to root, trip knox and lose your warranty... there is no way to go back. on verizon you may be screwed if you have signed/locked bootloaders. search on XDA about unlocked bootloaders for verizon. also: http://androidforums.com/threads/verizon-verizon-bootloader-unlock.856221/
aaaand... make sure to back up your mmc boot partitions so you can debrick if you mess up.
p.s. prepare to learn a lot of technical things. if that sounds annoying and you don't want to spend a lot of time on it you might be better off buying a used phone.
nxb said:
you will have to root, trip knox and lose your warranty... there is no way to go back. on verizon you may be screwed if you have signed/locked bootloaders. search on XDA about unlocked bootloaders for verizon. also: http://androidforums.com/threads/verizon-verizon-bootloader-unlock.856221/
aaaand... make sure to back up your mmc boot partitions so you can debrick if you mess up.
p.s. prepare to learn a lot of technical things. if that sounds annoying and you don't want to spend a lot of time on it you might be better off buying a used phone.
Click to expand...
Click to collapse
I'm not using Verizon. I'm using straight talk on a Verizon phone
Sent from my SCH-I535 using XDA Free mobile app
ST only has GSM AT&T and CDMA verizon... if you have an I535 past 4.3 you have locked bootloader problems.
Needing the pit file for the SCH-R530C. PLEASE! I am at the end of my tether. Thank you in advance, DaMoose
DaMoose517 said:
Needing the pit file for the SCH-R530C. PLEASE! I am at the end of my tether. Thank you in advance, DaMoose
Click to expand...
Click to collapse
Do you have any idea if the 530c and the 530x share a similar partition table? If they do then I can pull the one from my 530x
Lrs121 said:
Do you have any idea if the 530c and the 530x share a similar partition table? If they do then I can pull the one from my 530x
Click to expand...
Click to collapse
I do not know. I'd love to take the chance, but the risk of totally bricking the R530C is there . . . heck, let me try it.
Does anyone have a definite solution to this problem? I've read many opinions but haven't run across a solution. I have a Samsung unlocked S9+ running official AT&T firmware and userdata but the carrier specific apps and features still don't work. The best infomation I've found is that the IMEI numbers of the unlocked devices are not in AT&T system so the features/apps won't work.
If this is the case, has anyone had any luck getting AT&T to register their IMEI and get the features working?
What worked for me and others (see the at&t fw thread) is to call or chat with AT&T and give them a imei from a carrier branded phone(with your sim in, though this might not be required). Tell them you are trying to get wifi calling to activate and it is failing at the provisioning step and they will input your imei and it will reprovision. Then pull your sim and put it into your s9/+ running at&t fw and it will allow volte, wifi calling and call protect to work (these are the only ones I use).
Good luck
I talked with someone in AT&T technical support and they remoted directly into my phone, reset all app defaults and network settings.. This of course didn't fix anything so they opened a trouble ticket. They told me my IMEI was in their system and was OK. Haven't heard back yet.
why not just flash ATT U firmware?
I'm running AT&T official U firmware G965USQS2ARF4. What just occurred to me was that I didn't do a factory reset before or after applying it via ODIN.
Stuart R said:
I'm running AT&T official U firmware G965USQS2ARF4. What just occurred to me was that I didn't do a factory reset before or after applying it via ODIN.
Click to expand...
Click to collapse
Just did that... Didn't help.
Stuart R said:
Does anyone have a definite solution to this problem? I've read many opinions but haven't run across a solution. I have a Samsung unlocked S9+ running official AT&T firmware and userdata but the carrier specific apps and features still don't work. The best infomation I've found is that the IMEI numbers of the unlocked devices are not in AT&T system so the features/apps won't work.
If this is the case, has anyone had any luck getting AT&T to register their IMEI and get the features working?
Click to expand...
Click to collapse
Stuart R said:
I talked with someone in AT&T technical support and they remoted directly into my phone, reset all app defaults and network settings.. This of course didn't fix anything so they opened a trouble ticket. They told me my IMEI was in their system and was OK. Haven't heard back yet.
Click to expand...
Click to collapse
Yes your IMEI is in their system. But it's not an IMEI from a branded ATT phone. You have to have the IMEI from an ATT phone like others have said, and like i had to do or you will not get the features, no matter what firmware you flash. This has been discussed in many threads. You have to have ATT change your IMEI in their system.
elliwigy said:
why not just flash ATT U firmware?
Click to expand...
Click to collapse
Wont help unless you have a 965U or the IMEI from an ATT phone . ATT Features will not work on 965U1 IMEI. AT&T told me theses features wouldn't work on an unlocked phone and asked if i had the unlocked version. I told them no, it was an ATT phone i bought from Best Buy and it has an ATT logo (not the truth, got it from Samsung) and that i read in the forums that there were some issues with the S9 and that changing the IMEI fixed everyone's problems. I said i had my s8 here that everything works on and she said it's worth a shot to try and she changed mine in their system to the IMEI from my AT&T Branded S8 that i provided them. 965U1 has worked flawless ever since. All features work.
nugzo said:
Yes your IMEI is in their system. But it's not an IMEI from a branded ATT phone. You have to have the IMEI from an ATT phone like others have said, and like i had to do or you will not get the features, no matter what firmware you flash. This has been discussed in many threads. You have to have ATT change your IMEI in their system.
Wont help unless you have a 965U or the IMEI from an ATT phone . ATT Features will not work on 965U1 IMEI. AT&T told me theses features wouldn't work on an unlocked phone and asked if i had the unlocked version. I told them no, it was an ATT phone i bought from Best Buy and it has an ATT logo (not the truth, got it from Samsung) and that i read in the forums that there were some issues with the S9 and that changing the IMEI fixed everyone's problems. I said i had my s8 here that everything works on and she said it's worth a shot to try and she changed mine in their system to the IMEI from my AT&T Branded S8 that i provided them. 965U1 has worked flawless ever since. All features work.
Click to expand...
Click to collapse
sounds about right.. i mean you can switch csc while on U1 depending on the sim card inserted but U1 isnt meznt to have all the carrier crap they need for the special features to work so u get the bare minimum..
while on U firmware, it seems the csc doesnt fully switch like they did on the S8 devices.. i tested this on my sim unlocked vzw s9+ with an att sim and a sprint sim and although data and calls worked,it stsyed on verizon bootani and bloat etc etc no matter what i did.. before on s8 devices after a reset it would have changed the boot ani,bloat and woulda had all the carrier features..
im also surprised they changed your imei lol.. i thought that was illegal lol.. i guess if the carrier does it then its fine haha
nugzo said:
Yes your IMEI is in their system. But it's not an IMEI from a branded ATT phone. You have to have the IMEI from an ATT phone like others have said, and like i had to do or you will not get the features, no matter what firmware you flash. This has been discussed in many threads. You have to have ATT change your IMEI in their system.
Hard to believe that they would just accept another IMEI and register it to your phone. I thought these were all unique numbers that couldn't be used on more than one device. How did that change affect the phone that originally had the branded IMEI?
Click to expand...
Click to collapse
Stuart R said:
nugzo said:
Yes your IMEI is in their system. But it's not an IMEI from a branded ATT phone. You have to have the IMEI from an ATT phone like others have said, and like i had to do or you will not get the features, no matter what firmware you flash. This has been discussed in many threads. You have to have ATT change your IMEI in their system.
Hard to believe that they would just accept another IMEI and register it to your phone. I thought these were all unique numbers that couldn't be used on more than one device. How did that change affect the phone that originally had the branded IMEI?
Click to expand...
Click to collapse
Didnt affect original s8 i used at all. or the s9. I replaced the s8 with the s9 when it came out so i just used the sim out of the s8 when the s9 arrived. s8 is just a spare phone now. I asked the operator if this would disable the other phone that the IMEI came from and she said no. I put sim from s9 in s8 afterwards just to test and it worked fine. They arent changing the IMEI of your actual s9, it still shows your original IMEI in your phone settings. They are just using the IMEI you provided on their end. What is actually going on behind the scenes i dont know. Maybe somebody that works in carrier support or may just have knowledge on how this actually works could chime in. I'm guessing they just use the IMEI to activate the features, since the unlocked one isn't eligible. I saw a better explanation in one of the firmware threads, if i run across it i'll post the link.
Click to expand...
Click to collapse
I will reiterate what is said above and clarify my post. You aren't asking the support team to change your phones imei. I think as stated previously that is a forbidden/illegal maneuver. The support request is to change the imei which is active in the at&t system as only carrier branded phones are able to use certain at&t features.
If you have an old AT&T phone its imei can be used to "trick" at&t into activation/provisioning. Then you can put your sim into a U1 phone using at&t firmware and use carrier specific features.
Hopefully, this is easier to understand and clears up some of the confusion I may have introduced in my original reply.
jay2o01 said:
I will reiterate what is said above and clarify my post. You aren't asking the support team to change your phones imei. I think as stated previously that is a forbidden/illegal maneuver. The support request is to change the imei which is active in the at&t system as only carrier branded phones are able to use certain at&t features.
If you have an old AT&T phone its imei can be used to "trick" at&t into activation/provisioning. Then you can put your sim into a U1 phone using at&t firmware and use carrier specific features.
Hopefully, this is easier to understand and clears up some of the confusion I may have introduced in my original reply.
Click to expand...
Click to collapse
I presume I can use the IMEI from another brand of working AT&T phone such as an iPhone 6S (in this case, my wife's)?
Stuart R said:
I presume I can use the IMEI from another brand of working AT&T phone such as an iPhone 6S (in this case, my wife's)?
Click to expand...
Click to collapse
Another thought... Say I get an old Galaxy S6 which uses the same size Nano SIM as my S9+. I move my S9+ SIM to the S6, update it to the latest AT&T firmware and enable WIFI calling. If I then move my SIM back to my S9+, will the carrier features now work?
Stuart R said:
Another thought... Say I get an old Galaxy S6 which uses the same size Nano SIM as my S9+. I move my S9+ SIM to the S6, update it to the latest AT&T firmware and enable WIFI calling. If I then move my SIM back to my S9+, will the carrier features now work?
Click to expand...
Click to collapse
This is exactly what I'm doing. I use an older LG phone and the sim/IMEI then swap it to my u1 with AT&T fw after the device is provisioned.
jay2o01 said:
This is exactly what I'm doing. I use an older LG phone and the sim/IMEI then swap it to my u1 with AT&T fw after the device is provisioned.
Click to expand...
Click to collapse
Glad to know that works. I can pick up an old AT&T S6 pretty cheaply on ebay. Guess I'll give that a try. Thanks
Download visual voicemail from apk mirrow
jay2o01 said:
This is exactly what I'm doing. I use an older LG phone and the sim/IMEI then swap it to my u1 with AT&T fw after the device is provisioned.
Click to expand...
Click to collapse
I previously had an AT&T branded S8+ with the same SIM that I'm using in the unbranded S9+ but I guess I never provisioned (enabled) WIFI calling. Dunno.
The "trick" of giving them an IMEI from an ATT branded phone doesn't usually work any more, maybe it used to, years ago.
This is why I won't buy OnePlus phones any more. I love their devices, best bang for the buck on the market, but no amount of my fiddling would get ATT to recognize it and provision VoLTE... so no wifi calling, no HD calling... when you make a call, your data drops to 3G, etc...
My Essential, somehow was on their "BYOD" plan and so it would give me VoLTE and HD calling, but no wifi calling. No wifi calling is stupid, because you aren't using their network at that point, so why should they even care?
SquireSCA said:
The "trick" of giving them an IMEI from an ATT branded phone doesn't usually work any more, maybe it used to, years ago.
This is why I won't buy OnePlus phones any more. I love their devices, best bang for the buck on the market, but no amount of my fiddling would get ATT to recognize it and provision VoLTE... so no wifi calling, no HD calling... when you make a call, your data drops to 3G, etc...
My Essential, somehow was on their "BYOD" plan and so it would give me VoLTE and HD calling, but no wifi calling. No wifi calling is stupid, because you aren't using their network at that point, so why should they even care?
Click to expand...
Click to collapse
"maybe it used to, years ago"... That doesn't apply in this context does it as carrier features VOLTE and Wi-Fi calling weren't even in existence years ago. And I'm not sure you have to give them anything. The claim by some is that just provisioning the features with your SIM on a branded device is enough.
Stuart R said:
"maybe it used to, years ago"... That doesn't apply in this context does it as carrier features VOLTE and Wi-Fi calling weren't even in existence years ago. And I'm not sure you have to give them anything. The claim by some is that just provisioning the features with your SIM on a branded device is enough.
Click to expand...
Click to collapse
And as someone who has repeatedly tried it, it doesn't seem to work. You can give them an IMEI from another phone, but it usually doesn't work. Either the IMEI is "on their list", or from a phone that is on the BYOD list, or it isn't. It's not the phone's fault, it is that AT&T is kinda being dicks about this... They want you to buy their phones, because most people sign a contract to get the cheaper price, or use their NEXT financing to spread the costs out. That creates a barrier to exit for most customers and protects AT&T's revenue stream from monthly invoices.
While bringing your own device makes them just as much money from the monthly bill, it doesn't help them "retain customers by locking them into a contract", so they usually don't give you full functionality...
I have had a working SIM from an ATT branded phone that was properly provisioned, popped it into my other device, and VoLTE went away. I would call them up and give them the IMEI from the phone, or one that I know worked, and still no go. The one exception was the Essential, and that was because for whatever reason, Essential went to the effort to get it on their BYOD list.
Trust me, if it was easy, I would be doing it and buying OnePlus phones exclusively every 6 months and that would be the end of it. LOL
Essentially, my phone started reading "No service" even though I am at home where I normally get full bars. I chalked it up to a Visible issue, but the problem persisted even after several days and multiple restarts, so I put the SIM in my iPhone and it works great...
I then put a MInt Mobile SIM in the G7 Power and again "No service" but the SIM is detected because when one is not inserted it says No SIM but that goes away when I insert one, and I can read the ICCID in About Phone.
I tried a factory reset and even reflashed the most recent stock firmware using the the LMSA tool and no dice. Huge issue and don't even know why considering that my phone has always been stock. Could I actually be dealing with a hardware issue?
og1502 said:
Essentially, my phone started reading "No service" even though I was at home where I normally get full bars. I chalked it up to a Visible issue, but the problem persisted even after several days and multiple restarts, so I put the SIM in my iPhone and it works great...
I then put a MInt Mobile SIM in the G7 Power and again "No service" but the SIM is detected because when one is not inserted it says No SIM but that goes away when I insert one, and I can read the ICCID in About Phone.
I tried a factory reset and even reflashed the most recent stock firmware using the the LMSA tool and no dice. Huge issue and don't even know why considering that my phone has always been stock. Could I actually be dealing with a hardware issue?
Click to expand...
Click to collapse
It looks like your G7 power is locked ....so " No service" as expected...
If it is unlocked , using manually network searching to see if it sees any network around you....
Or type "*#06" , if it still has IMEI.....
Sent from my LG-LS997 using Tapatalk
cgigate said:
It looks like your G7 power is locked ....so " No service" as expected...
If it is unlocked , using manually network searching to see if it sees any network around you....
Or type "*#06" , if it still has IMEI.....
Sent from my LG-LS997 using Tapatalk
Click to expand...
Click to collapse
I don't think my phone is locked, as it was working fine on Visible for multiple weeks. Also, it's the Amazon edition and those are SIM unlocked. Do you mean some other type of lock?
Manually searching for a network results in it endlessly search for a network but never finding/listing any. Yes, *#06# results in the IMEI, MEID (HEX and DEC), and serial number being displayed.
I honestly think it's a hardware issue because I did flash the stock firmware using LMSA tool and that didn't help, but I do find that very hard to believe so I'm wondering if anyone has any other suggestions...
og1502 said:
I don't think my phone is locked, as it was working fine on Visible for multiple weeks. Also, it's the Amazon edition and those are SIM unlocked. Do you mean some other type of lock?
Manually searching for a network results in it endlessly search for a network but never finding/listing any. Yes, *#06# results in the IMEI, MEID (HEX and DEC), and serial number being displayed.
I honestly think it's a hardware issue because I did flash the stock firmware using LMSA tool and that didn't help, but I do find that very hard to believe so I'm wondering if anyone has any other suggestions...
Click to expand...
Click to collapse
Ok, if the manual search not able to find any network... The baseband chip/circuit has issue
Sent from my LG-LS997 using Tapatalk
cgigate said:
Ok, if the manual search not able to find any network... The baseband chip/circuit has issue
Sent from my LG-LS997 using Tapatalk
Click to expand...
Click to collapse
Okay. Is there some test I can run to confirm?
og1502 said:
Okay. Is there some test I can run to confirm?
Click to expand...
Click to collapse
What firm ware did u flash
og1502 said:
I don't think my phone is locked, as it was working fine on Visible for multiple weeks. Also, it's the Amazon edition and those are SIM unlocked. Do you mean some other type of lock?
Manually searching for a network results in it endlessly search for a network but never finding/listing any. Yes, *#06# results in the IMEI, MEID (HEX and DEC), and serial number being displayed.
I honestly think it's a hardware issue because I did flash the stock firmware using LMSA tool and that didn't help, but I do find that very hard to believe so I'm wondering if anyone has any other suggestions...
Click to expand...
Click to collapse
I used Visible for about a year,
I stopped getting a signal at home, no network connection.
Figured out that I could get a signal in some other areas if I drove around.
Visible uses Verizon network and is owned by Verizon.
I had used Verizon for almost 20 years before switching so I have a good idea where it should work.
I suspect that Verizon has changed some frequencies from 4g to 5g or something.
I contacted Visible several times even got a new sim but just couldn't get a dependable connection.
So I switched to Pure Talk USA a AT&T mvno.
My issue seems a little different than yours but it could be related.
Sent from my ocean using XDA Labs
og1502 said:
Essentially, my phone started reading "No service" even though I was at home where I normally get full bars. I chalked it up to a Visible issue, but the problem persisted even after several days and multiple restarts, so I put the SIM in my iPhone and it works great...
I then put a MInt Mobile SIM in the G7 Power and again "No service" but the SIM is detected because when one is not inserted it says No SIM but that goes away when I insert one, and I can read the ICCID in About Phone.
I tried a factory reset and even reflashed the most recent stock firmware using the the LMSA tool and no dice. Huge issue and don't even know why considering that my phone has always been stock. Could I actually be dealing with a hardware issue?
Click to expand...
Click to collapse
in the same boat currently with my g7 except i have service and use Verizon, but its extremely inconsistent. I also think its a hardware issue, but it only happened after I flashed a custom rom (Resurrection Remix). I don't think it's the custom rom though, as I went back to stock entirely and still the same issue. Haven't even owned my phone for over a year and its doing this.
What carrier u using now if ur on verizon that's the problem it don't like custom roms and which roms
roadkill42 said:
What firm ware did u flash
Click to expand...
Click to collapse
I used LMSA to flash the latest stock firmware package: OCEAN_AMZ_QPO30.85_23_cid50_subsidy_DEFAULT_regulatory_DEFAULT_CFC.xml.zip
While I've flashed custom ROMs on tens of phones in the past, this is an Amazon version of the phone with a locked bootloader so it's always been stock.
sd_shadow said:
I used Visible for about a year,
I stopped getting a signal at home, no network connection.
Figured out that I could get a signal in some other areas if I drove around.
Visible uses Verizon network and is owned by Verizon.
I had used Verizon for almost 20 years before switching so I have a good idea where it should work.
I suspect that Verizon has changed some frequencies from 4g to 5g or something.
I contacted Visible several times even got a new sim but just couldn't get a dependable connection.
So I switched to Pure Talk USA a AT&T mvno.
My issue seems a little different than yours but it could be related.
Sent from my ocean using XDA Labs
Click to expand...
Click to collapse
This is very interesting, but I actually noticed this issue when I was about 35 miles from home, and persisted throughout my trip home - so I don't think that's the problem for me. I appreciate your response though!
Malfrosty said:
in the same boat currently with my g7 except i have service and use Verizon, but its extremely inconsistent. I also think its a hardware issue, but it only happened after I flashed a custom rom (Resurrection Remix). I don't think it's the custom rom though, as I went back to stock entirely and still the same issue. Haven't even owned my phone for over a year and its doing this.
Click to expand...
Click to collapse
I suppose it could be related. Mine phone worked continuously then stopped. Nothing intermittent like what you are describing.
roadkill42 said:
What carrier u using now if ur on verizon that's the problem it don't like custom roms and which roms
Click to expand...
Click to collapse
I'm still using Visible, but on an old iPhone 6s Plus. I have a Mint Mobile SIM in the G7 Power for now - also says "No service" though I also have a perpetual unread voicemail notification with this Mint SIM inserted.
og1502 said:
I used LMSA to flash the latest stock firmware package: OCEAN_AMZ_QPO30.85_23_cid50_subsidy_DEFAULT_regulatory_DEFAULT_CFC.xml.zip
While I've flashed custom ROMs on tens of phones in the past, this is an Amazon version of the phone with a locked bootloader so it's always been stock.
This is very interesting, but I actually noticed this issue when I was about 35 miles from home, and persisted throughout my trip home - so I don't think that's the problem for me. I appreciate your response though!
I suppose it could be related. Mine phone worked continuously then stopped. Nothing intermittent like what you are describing.
I'm still using Visible, but on an old iPhone 6s Plus. I have a Mint Mobile SIM in the G7 Power for now - also says "No service" though I also have a perpetual unread voicemail notification with this Mint SIM inserted.
Click to expand...
Click to collapse
same here, it only stopped working after I flashed my third custom rom, I haven't been able to find a fix and I've dealt with this issue for around a month and it only gets worse. I hope it isn't hardware for you or me though.
Reflash the stock modems
roadkill42 said:
Reflash the stock modems
Click to expand...
Click to collapse
Certainly should be tried.
Code:
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
Sent from my ocean using XDA Labs
Quote: Originally Posted by og1502 I used LMSA to flash the latest stock firmware
roadkill42 said:
Reflash the stock modems
Click to expand...
Click to collapse
How to get those modem files?.... I know where to download the stock rom but .... gah I am a noob.
Visible NO SERVICE whatsoever, halp!! :crying::crying:
They inside the stock firmware
roadkill42 said:
They inside the stock firmware
Click to expand...
Click to collapse
Thanks! applied those from the latest android 10, still no service. so sad..
DO u know what else can be done? Thanks again
lessmeat said:
Thanks! applied those from the latest android 10, still no service. so sad..
DO u know what else can be done? Thanks again
Click to expand...
Click to collapse
Try the rr rom
roadkill42 said:
What carrier u using now if ur on verizon that's the problem it don't like custom roms and which roms
Click to expand...
Click to collapse
I'm having a similar problem. I'm on the Verizon network. I get a "Mobile network is not available" message. I was running LineageOS 17, then switched to Resurrection Remix 8. I have the same problem with both ROMs. I have been trying to narrow down whether or not this is a hardware issue or software issue or a verizon blocking issue.
tmiller101 said:
I'm having a similar problem. I'm on the Verizon network. I get a "Mobile network is not available" message. I was running LineageOS 17, then switched to Resurrection Remix 8. I have the same problem with both ROMs. I have been trying to narrow down whether or not this is a hardware issue or software issue or a verizon blocking issue.
Click to expand...
Click to collapse
It's rom ishues the new colt rom and the new rr should work . Most of these roms are for GSM carriers they are starting to get the cdma to work now
roadkill42 said:
It's rom ishues the new colt rom and the new rr should work . Most of these roms are for GSM carriers they are starting to get the cdma to work now
Click to expand...
Click to collapse
Newer than RR 8.6.4? Not sure I have heard of colt. I'lll have to dig into that.
I unlocked my note 10+ 5g from t-mobile, but it won't get service with verizon.
When I install a non-tmobile sim, the software does not switch from tmobile for some reason.
Also Sam Mobile only has t-mobile and metro pcs firmware availible for the sm-n976u
Does anyone know if there is a way to get the phone working with verizon? Thanks.
-God Bless
Try clearing Sim card tool kit data.
Network reset.
Clear system cache.
Edit Access point names to correct values.
That's all I got but sure there's more. Never had use more than the above but never changed carriers. Verizon advanced tech support should be able to help... AT&T would.
The Verizon Note 10+ 5G has a different model number. So they probably won't allow the T-Mobile/Metro/AT&T version on their network
iBowToAndroid said:
The Verizon Note 10+ 5G has a different model number. So they probably won't allow the T-Mobile/Metro/AT&T version on their network
Click to expand...
Click to collapse
I think you're correct. AT&T is compatible with Tmobile but not Verizon according to B&H Photo compatibility charts.
So it look like AT&T is in your future. AT&T is easier to deal with anyway. Do not use a corporate store though, use over the phone or online AT&T.
It may be possible to change out the C port PCB for the Verizon variant. Yes that PCB controls internet access. I can't confirm this is the only difference though! That PCB is only $20 and relatively easy to change out.
blackhawk said:
I think you're correct. AT&T is compatible with Tmobile but not Verizon according to B&H Photo compatibility charts.
So it look like AT&T is in your future. AT&T is easier to deal with anyway. Do not use a corporate store though, use over the phone or online AT&T.
It may be possible to change out the C port PCB for the Verizon variant. Yes that PCB controls internet access. I can't confirm this is the only difference though! That PCB is only $20 and relatively easy to change out.
Click to expand...
Click to collapse
It's gets service with att, but it still has the tmobile boot logo. I flashed the att rom, but it didn't help. The carrier is supposed to automatically switch when you insert a different sim card right?
I also tried *#272*imei# but it says "unable to process the request"
CPR.OP546 said:
It's gets service with att, but it still has the tmobile boot logo. I flashed the att rom, but it didn't help. The carrier is supposed to automatically switch when you insert a different sim card right?
I also tried *#272*imei# but it says "unable to process the request"
Click to expand...
Click to collapse
Is it on Verizon or AT&T???
My 60 second attention span is kicking in... now.
As for switching sims I never had to.
The boot logo is the least of worries.
Be glad you didn't brick it.
blackhawk said:
Be glad you didn't brick it.
Click to expand...
Click to collapse
It's actually super difficult to hard brick a Qualcomm device, and even if it is hard bricked and only enters EDL mode, it can be fixed as long as you have the correct files.
There are too many safeguards in place between Qualcomm and Samsung - the average user will always be blocked from doing anything that would brick a device. There's really no danger in flashing firmware whatsoever
blackhawk said:
Is it on Verizon or AT&T???
My 60 second attention span is kicking in... now.
As for switching sims I never had to.
The boot logo is the least of worries.
Be glad you didn't brick it.
Click to expand...
Click to collapse
I'm trying to use it with att because it won't get service with verizon at all.
It's very annoying having the tmobile bloatware. Also it should be compatible with att's 5g, but it only gets lte.
CPR.OP546 said:
I'm trying to use it with att because it won't get service with verizon at all.
It's very annoying having the tmobile bloatware. Also it should be compatible with att's 5g, but it only gets lte.
Click to expand...
Click to collapse
So then I'm assuming that it did not automatically change over to the AT&T splash screen and bloatware when you inserted an AT&T SIM?
iBowToAndroid said:
So then I'm assuming that it did not automatically change over to the AT&T splash screen and bloatware when you inserted an AT&T SIM?
Click to expand...
Click to collapse
Right. It does not have a multi-csc mode for some reason. I thought all samsung phones had that by default.
CPR.OP546 said:
Right. It does not have a multi-csc mode for some reason. I thought all samsung phones had that by default.
Click to expand...
Click to collapse
Not all, no. But all U models should have it.
Have you tried doing a full Odin firmware flash including an AT&T USERDATA file?
iBowToAndroid said:
Not all, no. But all U models should have it.
Have you tried doing a full Odin firmware flash including an AT&T USERDATA file?
Click to expand...
Click to collapse
Yes. That is what I meant by flashing the att rom. It does not seem to make a difference.
CPR.OP546 said:
Yes. That is what I meant by flashing the att rom. It does not seem to make a difference.
Click to expand...
Click to collapse
I may have a way to do it. No guarantees though
iBowToAndroid said:
I may have a way to do it. No guarantees though
Click to expand...
Click to collapse
I'm guessing the only option left is to root the phone, and then start manually removing things.
CPR.OP546 said:
I'm guessing the only option left is to root the phone, and then start manually removing things.
Click to expand...
Click to collapse
My method doesn't involve root, no. You can't root if you've taken an OTA update in March of this year or later
I hope I can be of some help.
I recently ordered a Note 10+ 5G - Locked Verizon from a popular online re-seller. When I turned it on, I was greeted with an AT&T boot logo. I was pretty upset, but I though I'd try to get it up and running on Verizon before spending a couple weeks sending it back and getting a replacement. I tried Verizon's online software and I couldn't get beyond the IMEI change. It kept telling me that the Note's IMEI was what I was already using with my Droid, which was obviously not the case. So, I headed into my local Verizon store.
Nothing they did would get my 4G SIM to work, so they swapped out for a 5G SIM for free, then switched my hardware IMEI numbers and proceeded to have a some difficulty getting on the network. After doing a network reset, it seemingly worked. More on that below. I was getting both data and voice over network. I was able to transfer my setting, apps, etc from my Motorola Droid with Samsung Switch. The phone indicates both 3G and 4G signals as I travel around town. 5G is not available in my immediate area, though it is in some cities I occasionally travel to, but I'm unable to test that just yet. I become aware that there are differences between Verizon's 5G and other networks and it seems the non-Verizon phone I have is probably for the best in terms of compatibility.
Unfortunately, texts frequently take 10-30 seconds to send. Images, gifs and other non-text MMS can take multiple minutes to send and sometimes just fail. Other times the recipient will receive them twice. I feel like this may be due to the poor coverage at my residence. Further testing in areas of good to excellent coverage are necessary. I tried changing the network settings from Settings > Connections > Mobile Networks > Network Mode, but anything other than the default "GLOBAL" would result in a disconnect of data and voice services. The only way to fix it was Settings > General Management > Reset > Reset Network Settings. This would restore the Mode to GLOBAL and bring back data and voice services.
In an effort to remove the AT&T branding, I learned how to trigger a carrier switch, dialed the code and changed it from AT&T to XAA. That got rid of the AT&T boot animation and I was able to remove all but 2 stubborn AT&T apps. I noticed that my android version was 10 and UI was 2.5, so I set out to update.
This is where things got frustrating. Every attempt to update through the settings > software update was met with failure. Try again in 24 hours, it would say. I assumed this was because I was now using a Verizon sim on an AT&T firmware, but I wasn't sure. I thought I might be able to flash to a Verizon firmware, but after several versions and some more research, I learned that going from 976U to 976V was not possible.
So, over the course of several days, I learned a lot. I looked up the firmware releases on AT&T's website for the 976U and saw that they matched the T-Mobile and MetroPCS versions. So, I settled on a T-Mobile version of Android 11 / UI 3.1. It updated without any issues and even remained in XAA mode. No bloatware, no loading images, all settings and apps the same.
So, even though I have an unlocked AT&T Note 10+ 5G 256GB and you have a T-Mobile, the fact that we both have a 976U model, I think there is hope for you to get up and running on Verizon.
Hope this has helped.