I need help, the Radio is new, an i cant find a Description how can i get to the Recovery Mode with the Hardware Button.
i had a Pumpkin and push only long on the Power Button until i get to the Recovery Mode. Now i do the same way with the new Radio Unit, but after blinking 3 times nothing happens. I try it again with short push on the Powert after Blinking 3 times and its the same.
I need it to know to install a new Oreo ROM.
Thanks in advance
@lavan79, Did you try not to hold power button, just quick clicks more time on it after 3 times blinking?
Yes i tried one time , but i think i do it again when i have desire to try ist. The other ROM runs good. Do you have the same Radio and it works with the quick clicks ?
Related
Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran
s_m_s said:
Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
i am mohsen from iran tehran
Click to expand...
Click to collapse
you can press start + ok + reset. it will help you recover your pda
salam
salam agha mohsen man ham moshkele shoma ro daram agar dorostesh kardin man ro ham khabar konid. 09195388556
ghorboone dastet
please help me out
Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
SKYWOR said:
Hi All,
While Upgrading My i-teq x-bond ROM...
I Followed the Steps but after Checking the Image...
I Reset My Phone...
Now it doesn't response, I can only see the light when I'm charging the Phone!!!
Nothing else response...
I tried to Press (Call+End Call+Power) again to ReInstall the ROM But it also doesn't Response...
Also I want to know how to Enter Bootloader???
and How to enter the Engineering Mode???
Thanks
Click to expand...
Click to collapse
wait we need more Details id you try leaving the phone charging then take battry out and put it back in? also does the Device power on? I mean do you see the qtex screen you know the boot screen? also try putting it in bootloader mode then flash
Same Problem
I have been facing the same kind of problem. The phone light flashes when charging and when I boot the phone, it just shows the iteq logo. I have tried the Call Start+Call end+power combination but nothing happens. Sometime it shows the orange light besides the power button but the logo still remains on the screen. On one ocassion, it did enter some image mode but gave an error that no image found. I dont have the rom either to flash it. Can someone please post the rom online if they have it and also help if they have faced similar issues.
Iteq X-bond
try
Windows flag button (Start)+OK+reset
if it doesn't work then install new windows
reseting
1 press and hold the [WIndosFlag(start)] and [ok] buttons somultaneously
2 press and release the [reset] button
3 wait up to the leds in the keyboar flahsing 2 or 3 time (less tha 5 seconds)
4 release the [WIndosFlag(start)] and [ok] buttons
must be start the resetting to the fabrique settings
[WIndosFlag(start)] button is in the down left corner
[ok] button is in the down right corner
if this not works the the keypad is dammage
iteq x-bond totally drained battery
When the battery is totally drained, all you have to do is charge it. Now here is the tip. when you charge it(totally drained iteq x-bond battery), the phone will enter into pre-charge mode for about 30min to 2 hrs( depending on how drained the battery is), the end-call button together with the right double arrow button will light steadily. Do not on the unit as this will only aggrevate the problem. Wait until the phone passes through that pre-charge mode. When the end-call button starts to flash, that means the pre-charge period is over. You can now press and hold the on/off button for about 5 seconds and the phone will start-up normally. Your problem is solved. That's it. This procedure will work only on the presumption that you did not do anything on the phone beforehand such as upgrading etc....
Hello,
I was trying to flash several roms alla day w/o luck. Almost always I had problems with the screen, I should press 2mm below a key or an icon in order to select it.
Anyway, I came across this thread and tried to flash this rom that is described in the post, with fastboot, not odin (somehow i couldn't get it to work).
After installing it I rebooted the phone and got this : http://www.youtube.com/watch?v=_jif-7fzJe4
I dont have to press and hold in order to open the phone, just touch the power buton and it's on. In addition I can't get into Bootloader, that's why I ask for your help.
Any help of what may be wrong and what I can do to fix it?
I managed to enter modem mode , holdind up and down volume butons and power one. I flashed the stock rom with odin.
Now the screen continues to behave like in the video (above post) but if i turn it on, and call it I hear (on the calling phone) the busy tone like someone's talking..
Okay guys, I have an annoying problem. My phone after the ICS update does not want to go into CWM Recovery with the Power button + vol down (or up) method. I can never get the darn thing to work. It just loads up until the white samsung logo and then goes black and just vibrates. Any idea what could be the problem? It's an issue because it means I can't root or anything since stock won't allow me to go into recovery. The only way I used to get into recovery was through rom manager and I obviously need super user permissions to do that.
Another thing is, whenever I power on my phone with the usb cord plugged in, it automatically enters download mode. I know you're suppose to hold certain buttons but I just power the thing on and it goes straight to the DL mode screen. I'm thinking these two things could be related.
Any idea on how to fix this? I went back to complete stock and it didn't do a thing.
ArecxP said:
Okay guys, I have an annoying problem. My phone after the ICS update does not want to go into CWM Recovery with the Power button + vol down (or up) method. I can never get the darn thing to work. It just loads up until the white samsung logo and then goes black and just vibrates. Any idea what could be the problem? It's an issue because it means I can't root or anything since stock won't allow me to go into recovery. The only way I used to get into recovery was through rom manager and I obviously need super user permissions to do that.
Another thing is, whenever I power on my phone with the usb cord plugged in, it automatically enters download mode. I know you're suppose to hold certain buttons but I just power the thing on and it goes straight to the DL mode screen. I'm thinking these two things could be related.
Any idea on how to fix this? I went back to complete stock and it didn't do a thing.
Click to expand...
Click to collapse
check ur pm mate
Its power button + volume up AND down... hold both buttons and the power button.
sulpher said:
Its power button + volume up AND down... hold both buttons and the power button.
Click to expand...
Click to collapse
I wasn't being specific, I just named the buttons off the top of my head. Either way, the methods don't work
ArecxP said:
I wasn't being specific, I just named the buttons off the top of my head. Either way, the methods don't work
Click to expand...
Click to collapse
My phone was being a bit finicky with this as well, I found the below sequence to work for me every time.
Press and hold both vol+ and vol-
Press and hold power
Wait until phone is vibrating once every couple of seconds
Release power
Release vol+ and vol-
ArecxP said:
I wasn't being specific, I just named the buttons off the top of my head. Either way, the methods don't work
Click to expand...
Click to collapse
u need to b specific to get proper help.
u stated "Either way, the methods don't work ", specifically what methods r u talking about, there is only one method in using the buttons that works as RabidSmurf has stated, but first pull battery and dont keep usb plugged in, if that didnt work redownload cwm, check the md5 checksum and reflash using odin
To get into download mode I'm holding power+vol up+vol down
after the phone starts up release the power and keep holding up+down.
Let me know how it works.
ArecxP said:
Okay guys, I have an annoying problem. My phone after the ICS update does not want to go into CWM Recovery with the Power button + vol down (or up) method. I can never get the darn thing to work. It just loads up until the white samsung logo and then goes black and just vibrates. Any idea what could be the problem? It's an issue because it means I can't root or anything since stock won't allow me to go into recovery. The only way I used to get into recovery was through rom manager and I obviously need super user permissions to do that.
Another thing is, whenever I power on my phone with the usb cord plugged in, it automatically enters download mode. I know you're suppose to hold certain buttons but I just power the thing on and it goes straight to the DL mode screen. I'm thinking these two things could be related.
Any idea on how to fix this? I went back to complete stock and it didn't do a thing.
Click to expand...
Click to collapse
Make sure it is not attached to any USB. Not even the power outlet because it will take you to firmware update mode (download mode) and hold up down volume keys and power until you see the white Samsung logo. good luck!
i had to deal with this when the firmware failed to ugprade for some reason, what i did was download odin and the stock rom and flash it with odin, i was back up in no time
Not booting
Frnds plz help
After flashing am n m same soc chipset custom rom my phone is not going in cwm also another problem is after pressing the power button the phone screen is gping black n then boot audio is playing but phone is not booting completely.
To be more specific i have cqnvas 2 plus with mt6589 and pne site there was eom name note 5 evolution for a116 hd with same soc i.e. mt6589 hence i flashed the rom it flashed succesfully also but then the problems occurred.
Plz help me fast thx in advance.
Hey guys, I used FlashTool and something went wrong. Ever since, My phone will only be a black screen when its turned on and I can't go into recovery mode. I can't work out how to restore it without. Please Please Help!?!?!?
Flas again with flashtool.
Before flashing press and hold power and volume up buttons together and hold about 10 seconds untill phone vibrate three times.Than star flashtool,hit flash and when you pop up windows show press and hold volume down button and connect phone to cable and flashing will succed.
Allek84 said:
Flas again with flashtool.
Before flashing press and hold power and volume up buttons together and hold about 10 seconds untill phone vibrate three times.Than star flashtool,hit flash and when you pop up windows show press and hold volume down button and connect phone to cable and flashing will succed.
Click to expand...
Click to collapse
Just did another one, Now the on button does nothing. My phone just won't turn on...
A couple of things that may help here
What model is your phone and what did you flash?
Please try and help us help you and let us know what you did
gregbradley said:
A couple of things that may help here
What model is your phone and what did you flash?
Please try and help us help you and let us know what you did
Click to expand...
Click to collapse
Its the D6603, I flashed a Marshmallow firmware, Then tried the stock firmware in order to fix it.
This morning all its doing is showing battery dead symbol despite being charged all night.
Jolbol1 said:
Hey guys, I used FlashTool and something went wrong. Ever since, My phone will only be a black screen when its turned on and I can't go into recovery mode. I can't work out how to restore it without. Please Please Help!?!?!?
Click to expand...
Click to collapse
Great New, I got it working again, Seems like battery life may have been a key issue here. Its loaded up, but got stuck on the blue musical bit and made some horrific beeping noise and keeps rebooting. Any help? I can't seem to get into recovery mode, Maybe thats just my method.
Hello,
sorry that I have to bother you with this.
I had a S6 (G920F) with Maniacx Ressurection Remix Unofficial OREO 6.10 , with Magisk 7.10 and TWRP 3.2.1 running.
Because of a problem with calls, I flashed a .zip that fixed the problem before (it's CallAudioFix.zip in that thread – can't find it right now, but I can look for it later if it's any help). That sent my phone into a bootloop.
My problem is that I can't boot into Recovery or Download mode. Windows (in a VirtualBox) finds a SAMSUNG_Android device per USB, but ODIN can't find it (doesn't show anything under ID:COM). ADB in my terminal finds the phone, but it shows it as unauthorized, so I can't use it, either.
I appreciate any help – thanks in advance!
Try pressing all botton after screen turn off press recovery combo botton fast or download mode combe ,that worked for me once when i downgraded without wiping data
amin44 said:
Try pressing all botton after screen turn off press recovery combo botton fast or download mode combe ,that worked for me once when i downgraded without wiping data
Click to expand...
Click to collapse
Thanks for your tip, didn't work for me, sadly. If I press and hold the combination for the recovery, I get back into my bootloop. If I press the combination for download mode, nothing happens until I hold it for too long and trigger the battery disconnect (volume down + power).
Bromsky said:
Thanks for your tip, didn't work for me, sadly. If I press and hold the combination for the recovery, I get back into my bootloop. If I press the combination for download mode, nothing happens until I hold it for too long and trigger the battery disconnect (volume down + power).
Click to expand...
Click to collapse
Try holding all botton for long time about 1 min ,or open phone remove battery connector and add it again ,then recovery combo ,for me it took some time and trying to get for recovery ,press combo before kernel logo appear
amin44 said:
Try holding all botton for long time about 1 min ,or open phone remove battery connector and add it again ,then recovery combo ,for me it took some time and trying to get for recovery ,press combo before kernel logo appear
Click to expand...
Click to collapse
I'll rather avoid trying to remove the battery for that.
If I hold all buttons, I can only get the "Samsung S6" screen to flash for a second before it goes off and on again (tried for a minute as you suggested).
I tried holding the combos before the kernel screen, directly at it and holding it for a minute, but it only sends me back to the bootloop. Also, I don't get any text on the kernel screen.
Guess I have to keep trying around for a bit...
Try after that flash appears for second to press combo fast i remember that worked for me at same state of bootloop
amin44 said:
Try after that flash appears for second to press combo fast i remember that worked for me at same state of bootloop
Click to expand...
Click to collapse
No luck so far with that approach yet. :/ But thanks again for the suggestion.