Related
Hi,
I have a Erisin MTCD unit, flashed with the 1.92a KGL MCU and latest Malaysk ROM. I experience some issues with my iPhone 6.2 iOS 10 when streaming music via a2dp. Bluetooth is connected, I can make calls. But when I try to play songs via a2dp app there is no sound, although my head unit receives the song info and I am able to skip to the next song via the app. Has anyone resolved this issue? Or did I just miss to set the volume setting somewhere?
Thanks for the help!
Marc
Maybe on the phone?
Getapped and getalked with 6603
Nope. The phone is working fine in all other environments but on my unit.
Hi, i have the same problem.
My HU is LM version.
I wipe in recovery all data and cache and install for test da-Anton beta3 Rom. After reboot a2dp app works fine.
When I have more time I go back to Malaysk ROM and test again.
Gesendet von meinem LG-D855 mit Tapatalk
I fiddled around a little bit and went to configuration/apps/Bluetooth and hit "deinstall update". It went from Bluetooth 2.0 to Bluetooth 1.0 and now it seems to work. Is there another update for the Bluetooth app available ?
I will try da-Anton when I notice any problems. Thanks for the hint.
I experienced this issue with the latest malaysk rom.
In my case the luckypatcher caused the problem, after when I activate in the xposed framework.
When I unchecked in xposed the A2DP worked again.
I had this issue and reinstalled ROM twice but no fix. Found out it stopped working after i installed the bluetooth apk from the OEM folder. Haven't installed this time and all has been fine.
Yes, I can confirm this, when installing the Bluetooth app from the oem folder A2DP stops working. I haven't tried Malaysk v10 yet.
Hi
I recently updated my GPS's firmware and MCU to the latest available. (GPS is Erisin ES3009F)
MCU Version
MTCD_LM_V2.52_1
Build Number
rk3188 (blah blah blah)
But unfortunately all canbus settings are gone and I'm not able to find any solution. I have tried many different options from the canbus menu (factory settings) but everyone of them has a problem
Option 1: No (works but the GPS wont start after closing the car)
Option 2: 11 FORD_MONDEO (Simple) the GPS wont start even 1 time
Option 3: 49 FOCUS_MONDEO_EXPLORER (Simple) same as the 1st
Option 4: 62 FOCUS_ECOSPORT&ESCAPE&CARNIVAL (Simple) same as the 1st
After many tries, I connected the red and yellow cable (not from the canbus but from the ones that are "free") and GPS works, but it wont sleep at all and it will consume A LOT OF energy (and my battery died too.......)
So (conclusion time), the GPS will either work but no sleep at all or it will work for the first time and after closing the car, it stops working (I forgot to mention that the car is Mondeo MK4)
Any help is welcome
THANKS
downgrade MCU? try with older dmcu.img
ozzyboy said:
downgrade MCU? try with older dmcu.img
Click to expand...
Click to collapse
I tried with 1.92 version (as far as I remember) and still the results are the same
with what version of mcu all settings worked right? do you remember that? ... if yes try it exactly with that vrs.
ozzyboy said:
with what version of mcu all settings worked right? do you remember that? ... if yes try it exactly with that vrs.
Click to expand...
Click to collapse
yes
luckily i had a screenshot
it was v1.63_1 (built at jun 12 2016)
but I cant find it anywhere
in this post you can find some LM mcu ... browse for LM mcu between posts ....or try to request here or request to seller support.
ozzyboy said:
in this post you can find some LM mcu ... browse for LM mcu between posts ....or try to request here or request to seller support.
Click to expand...
Click to collapse
Thanks but I have seen this thread already, plus erisin has been ignoring me for the last 2-3 weeks (so no reason for me, to speak with them)
I will look again in this thread though
t-shock said:
Hi
I recently updated my GPS's firmware and MCU to the latest available. (GPS is Erisin ES3009F)
MCU Version
MTCD_LM_V2.52_1
Build Number
rk3188 (blah blah blah)
But unfortunately all canbus settings are gone and I'm not able to find any solution. I have tried many different options from the canbus menu (factory settings) but everyone of them has a problem
Option 1: No (works but the GPS wont start after closing the car)
Option 2: 11 FORD_MONDEO (Simple) the GPS wont start even 1 time
Option 3: 49 FOCUS_MONDEO_EXPLORER (Simple) same as the 1st
Option 4: 62 FOCUS_ECOSPORT&ESCAPE&CARNIVAL (Simple) same as the 1st
After many tries, I connected the red and yellow cable (not from the canbus but from the ones that are "free") and GPS works, but it wont sleep at all and it will consume A LOT OF energy (and my battery died too.......)
So (conclusion time), the GPS will either work but no sleep at all or it will work for the first time and after closing the car, it stops working (I forgot to mention that the car is Mondeo MK4)
Any help is welcome
THANKS
Click to expand...
Click to collapse
You forgot to include a photo of the information of the sticker onto the canbus box
Enviado desde mi D6603 mediante Tapatalk
ikerg said:
You forgot to include a photo of the information of the sticker onto the canbus box
Enviado desde mi D6603 mediante Tapatalk
Click to expand...
Click to collapse
The Canbus is inside the GPS unit
Is there any other ford canbus option for other brand rather than "Simple"?
try it
But the best way is to ask Erisin for the correct option on factory settings
ikerg said:
Is there any other ford canbus option for other brand rather than "Simple"?
try it
But the best way is to ask Erisin for the correct option on factory settings
Click to expand...
Click to collapse
Unfortuantely, no
I asked them, but yet to answer...........
Got problems with interated canbus in Erisin 3015 too.
Support = 0
I try to install a external canbus decoder and switch dip 3 to off.
I have a Wondeffo HU (PX5 4GB Oreo, v2.83 MCU), but dont working the Convers+, I cant see the Climate... only the steereing buttons workin.
My Mfriend has Bosion 6.0, thats workin great.
<img src="https://thumb.ibb.co/f6OX2d/29541482_10216565646958469_8683319995895379641_n.jpg" alt="29541482_10216565646958469_8683319995895379641_n" border="0"> <img src="https://thumb.ibb.co/dAZ0oJ/29542991_10216565645278427_6955562041658564393_n.jpg" alt="29542991_10216565645278427_6955562041658564393_n" border="0"> <img src="https://thumb.ibb.co/mHX38J/33303711_1966988713376157_199401969910022144_n.jpg" alt="33303711_1966988713376157_199401969910022144_n" border="0"> <img src="https://thumb.ibb.co/mBaO8J/33455431_1966988446709517_5621947658856824832_n.jpg" alt="33455431_1966988446709517_5621947658856824832_n" border="0">
Canbus
o_tom said:
I have a Wondeffo HU (PX5 4GB Oreo, v2.83 MCU), but dont working the Convers+, I cant see the Climate... only the steereing buttons workin.
My Mfriend has Bosion 6.0, thats workin great.
<img src="https://thumb.ibb.co/f6OX2d/29541482_10216565646958469_8683319995895379641_n.jpg" alt="29541482_10216565646958469_8683319995895379641_n" border="0"> <img src="https://thumb.ibb.co/dAZ0oJ/29542991_10216565645278427_6955562041658564393_n.jpg" alt="29542991_10216565645278427_6955562041658564393_n" border="0"> <img src="https://thumb.ibb.co/mHX38J/33303711_1966988713376157_199401969910022144_n.jpg" alt="33303711_1966988713376157_199401969910022144_n" border="0"> <img src="https://thumb.ibb.co/mBaO8J/33455431_1966988446709517_5621947658856824832_n.jpg" alt="33455431_1966988446709517_5621947658856824832_n" border="0">
Click to expand...
Click to collapse
Hire is problem PX3 is better for Ford. PX5 don't see Ford Can
yaris1 said:
Hire is problem PX3 is better for Ford. PX5 don't see Ford Can
Click to expand...
Click to collapse
What do you mean no PX5 work with Ford?
.
nic2k said:
What do you mean no PX5 work with Ford?
Click to expand...
Click to collapse
no Canbus communication. does not work with Converse, climate control , open and close door. On px3 everything works with out problem.
If there are ready protocols drawn from the Ford, which cooperate with the car and radio on px3. Car has not changed the protocol, only the radio has changed the processor and android from 7.1 to 8.0
Just total bs...
PX5 is totally working fine in my '18 Focus ST even with the newest 3.06 dmcu and Hal9k Rom.
Thanks for the info. Climate control not working is a big issue for me. Are all PX5 units affected by this or is it specific to one brand? Or do you think it's Android 8.0 that's the issue?
LinkseD said:
Just total bs...
PX5 is totally working fine in my '18 Focus ST even with the newest 3.06 dmcu and Hal9k Rom.
Click to expand...
Click to collapse
send photos as proof how does Converse work on your ford and shows you radio stations, AUX or CD INFO. climate control on HU screen. OPEN AND CLOSE DOOR.
---------- Post added at 01:27 PM ---------- Previous post was at 01:16 PM ----------
nic2k said:
Thanks for the info. Climate control not working is a big issue for me. Are all PX5 units affected by this or is it specific to one brand? Or do you think it's Android 8.0 that's the issue?
Click to expand...
Click to collapse
It's hard to say, it could be a px5 problem and it could be Android 8. The problem has not been solved yet. Tested radios are: ISUDAR ERISIN XTRONS WONDEFOO
This is all i got for now, can upload much more if you want me to...
But it should be proof enough...
(drivers door and trunk open)
This unit btw is a Witson one, currently with MTCE_MX_3.06 and Hal9k Rom v3.1.1
Everything works fine but WiFi and BT after changing the board. So far I tried upgrading MCU, selecting all options available for BT type on BT settings on factory settings but none works.
When I go back to PX3 board, WiFi and BT work again with the same BT setting on factory settings.
Any suggestions?
BR
hmotwr said:
Everything works fine but WiFi and BT after changing the board. So far I tried upgrading MCU, selecting all options available for BT type on BT settings on factory settings but none works.
When I go back to PX3 board, WiFi and BT work again with the same BT setting on factory settings.
Any suggestions?
BR
Click to expand...
Click to collapse
Wich unit (manufacturer) did you have prior to update?
Perhaps you have yo move to other manufacturer mcu update that supports to px5
Enviado desde mi D6603 mediante Tapatalk
I had HXD, unknown to many, I have now HA 2.59 wich works all right with the px3 board, but wifi and BT won't work when I install the px5
Afaik...bt & wifi are out of px5 board....are you sure you have connected well your px5 board?
And did you try before upgrading to HA if with HXD worked?
I suggest you to ask these questions on the specific thread used to buy the px5 board
Enviado desde mi D6603 mediante Tapatalk
ikerg said:
Afaik...bt & wifi are out of px5 board....are you sure you have connected well your px5 board?
And did you try before upgrading to HA if with HXD worked?
I suggest you to ask these questions on the specific thread used to buy the px5 board
Enviado desde mi D6603 mediante Tapatalk
Click to expand...
Click to collapse
It didn't work with the HXD MCU either. Board is connected ok, all pins in.
Are you on malaysk s rom?
Nomader0 said:
Are you on malaysk s rom?
Click to expand...
Click to collapse
Tried malasyk ROM, didn't work either.
This is a picture of the network card. Looks like the same on most of the current HUs
https://goo.gl/photos/TcrY75wZc3F2Tbkw7
To me, no autosleep after upgrade PX3 to PX5. No chance.
So the upgrade isn´t fully compatible to the units compare with the car.
Had the same problems as well. No BT no wifi- px5 board was mounted well (thought so). After remounting it again both worked. Set up my account and after using it for 3 hrs the connection failed again... Then I found out that I had to press it better on the board again and had to tighten up the screws again. Right now- it works since one week.
makes2068 said:
To me, no autosleep after upgrade PX3 to PX5. No chance.
So the upgrade isn´t fully compatible to the units compare with the car.
Click to expand...
Click to collapse
Dont you have a unique/vehicle specific issue with canbus. My understanding is that you were able to enable autosleep by disabling canbus.
That's quite different to 'isnt fully compat.'
Suggest providing context when making statements that might imply to others that there is a significant compatibility issue.
Cheers.
hmotwr said:
Everything works fine but WiFi and BT after changing the board. So far I tried upgrading MCU, selecting all options available for BT type on BT settings on factory settings but none works.
When I go back to PX3 board, WiFi and BT work again with the same BT setting on factory settings.
Any suggestions?
BR
Click to expand...
Click to collapse
everybody solved the problem? i also have the same issue. please advice. thanks.
Nope, no solution yet.
hmotwr said:
Nope, no solution yet.
Click to expand...
Click to collapse
What is the bluetooth module set in Factory Settings for your HU with PX3 board installed?
Also please install terminal emulator like Termux (available at play store) and type command ps | grep gocsdk, ps | grep sdsdk and post output here.
marchnz said:
Dont you have a unique/vehicle specific issue with canbus. My understanding is that you were able to enable autosleep by disabling canbus.
That's quite different to 'isnt fully compat.'
Suggest providing context when making statements that might imply to others that there is a significant compatibility issue.
Cheers.
Click to expand...
Click to collapse
No thats not correct. Disabling canbus = no ignition starting anymore. Only manual power on and off.
So to me, it isn´t fully compatible. That´s an important information to others to beware them of possible problems.
[email protected] said:
No thats not correct. Disabling canbus = no ignition starting anymore. Only manual power on and off.
So to me, it isn´t fully compatible. That´s an important information to others to beware them of possible problems.
Click to expand...
Click to collapse
Again, vehicle specific issues potentially related to wiring issue and the factory settings for power on not set correctly. This is nothing to do with the MCU revision. My understanding is that you experienece sleep issues and then blamed cross mcu update because of this new issue.
The very issue of you machine not sleeping is a great enough indication that other issues are at play.
Wiring issues not possible cause there is only one wire (battery+) connected. Ignition power is set by canbus.
So, what should be wrong?
Power settings in factory settings are not possible. Tell me where they are!
There is only one setting called Power status (on, off, remind latest)
[email protected] said:
Wiring issues not possible cause there is only one wire (battery+) connected. Ignition power is set by canbus.
So, what should be wrong?
Power settings in factory settings are not possible. Tell me where they are!
There is only one setting called Power status (on, off, remind latest)
Click to expand...
Click to collapse
can you do me a favor,
can you cut the ignition power and connect it to a 12 volt live and when the units boots up, remove the cable and see what it does..
just try to take control of that as a test.
in my case i have cut the wire and connected to another 12 volt source that gives power for 3-4 minutes after car has been locked.. if i let it as it was, as soon as i would remove the key the unit would initiate a shut down..
???
Got no ignition power wire connected! So i can´ t cut it!
Quadlock from VW hasn´t got such a wire. Only battery+
That can not be.. can you post photos of the back of your unit and cables
I updated the MSU and Seicane sent me a new system update. MCU is MTCE-2.65. After updating was complete i had lost my Bluetooth. WIFI works normal and all buttons around the HU is working normal Bluetooth is missing the device name and pass code that was there when it came stock. wont find my phone or odb2 adapter. I was wondering if there is a posiblity that it some how changed the Bluetooth settings?
Did you find a fix?
Hello Cody,
Did you get any feedback on this?
I've got the same problem on a MTCD GS unit, unresolved!
Richard.
Hello. I fixed the damaged radio by replacing the PX5 module. The radio has started working, however the sound is only from the radio and bluetooth. No sound from USB, internet, navigation - displaying correct. I don't have an amplifier in my car. The radio comes with a CANBUS but I have a version of the car without CANBUS. Could this cause a problem with the sound? Please help.
You are in the wrong Forum. This is for FYT Head Units and you have an MTCD Head Unit. There is a forum for that where you will find the right people.
But anyway, did your unit used to have a PX5 and you replaced it by another PX5? Audio selection and processing happens a the Motherboard (the MTCD). There, the chip in charge of Sound source selection and processing selects from Bluetooth Chip, Radio Chip, and the PX5 (that generates any App-sourced sound like Navigation and MP3 playing). For some reason either the motherboard does not like your PX5 (faulty?) or there is some misconfiguration at the Android Level and PX5 is not reproducing sounds.
Have you changed anything on the Factory Settings?
But definitely your problem is not at the Canbus, but either at Android Config, PX5, or how the MTCD is communicating with the PX5
Thank you very much for the information, I'm new here so I'm still lost. I will move the topic to the appropriate forum. Thank you.
Hi, post system info, mcu version.
MCU version CSN2_D_1152020_114103
Android 9
bogsie said:
MCU version CSN2_D_1152020_114103
Android 9
Click to expand...
Click to collapse
It's not an MTCD unit, search forums for CSN2