Related
Hello everybody,
I want to tell you what happened to my Touch Pro this evening:
On the display (also if the device is off) appeared a small rectangle in the center (about 2x3 cm) made from bubbles. Well, not bubbles, I’m quite sure that are liquid crystal. If I put pressure with the finger the “bubbles” move and follow the pressure also out form the edge of this small rectangle)
As I can reach a decent camera I’ll post some photos of this rectangle.
The strange thing is that the device didn’t fall in ground, didn’t have temperature range; nothing hit it and so on. It was in my pocket well safe!!
If display is on the problem is quite invisible, if display is "black" or off... ....Grrrr!!!
Now, my questions:
1) Warranty is also for display?
2) How warranty works in Italy? Where should I ship the item? Which times?
3) If I have ship the device, sould I load the original rom & radio? Where can I find the rom?
Certainly, first thing I’m going to do Monday morning Is to call Italy HTC’s support number…
Thanks a regards,
Andrea
The "oil spot" problem isn't a broken display. It's the touch sensitive layer, which has been subject to too much pressure (carrying it in your pants pocket, etc). This has been happening on a bunch of Touch Pros and Diamonds. You should still be able to use it just fine, but touch sensitivity may get worse over time.
HTC may or may not be willing to replace it for you (and if so, they may or may not charge some kind of fee). Although it's just a hardware change, you should probably recover stock SoftSPL for warranty.
I have the "oil patch" problem with my Touch Pro. Unfortunately when I first noticed, HTC would not fix it for me, so I still have the oil patch on my screen, although everything still works fine so far. If it gets worse, I plan on buying a replacement LCD/touchscreen and replacing it myself:
http://mobile.brando.com.hk/prod_detail.php?prod_id=03799
I've noticed this problem on quite a few of the original touch / elf / 6900 phones, including my old personal phone which I used in this condition for many many months without every having any actual issues. It is strange but like you said: pretty much not noticeable when on and probably just best left alone unless it really bothers you.
I have the same spot but it is not causing any problems that I noticed but there is many who have this spot in the diamond forum.
today i also noticed this on my touch pro..i sort of fell asleep on it and i think i might have messed it up
i can see that oil spot that you mention but only if i tilt the phone at a certain angle and only if the screen is off.When the display is on i can see everything properly
The problem:
Touch function is messed up badly..i tested in notes application and sometimes when i press at a point X the dot appears somewhere else on the screen...Internet browsing is a pain in the ass like this...
i also noticed one thing..i took the stylus out, put the phone next to my ear and i tapped at the area outside the oil mark. I get the normal soft sound and pressure feeling as it should be.. When i do the same at the oil spot its rather hard feeling and sound..
i will contact HTC on monday and see what they say about it..
otherwise i will get a replacement for 159euros (inc installation) from pdatech...
Happened to my Fuze...
Happened to me too 60 days into owning it. I carry all my phones in my pocket, but have never had this problem. I brought it into the at&t store that I got it at and they never saw it either (it is only a few months old for them and have not had any complanints yet). They were going to replace it for me but were sold out. They had me call the warranty department and they replaced it with a refurbished unit (although all of their refurbished units are brand new as of this point because the phone is so new for at&t).
If you got your phone through at&t call warranty support and they will swap it out if the unit is under warranty (which being 2 months old at this point it will be).
This happened to my Fuze as well. I tried to call AT&T support and visit a corp store but they ruled it as physical damage, thus voiding my warranty. Apparently the "crystals" under the display are cracked/damaged, causing the rectangle. Who knows.
has anyone successfully sent a touch pro raphael to HTC repair shop to be repaired under warranty with this issue?? its really bothering me that i can see it and i feel like it will affect my phone eventually...
Add me to the list too.. I am going to try to get mine replaced through Sprint if it gets bad. I hope they know this is an issue/defect and not something like water damage
ez345 said:
has anyone successfully sent a touch pro raphael to HTC repair shop to be repaired under warranty with this issue?? its really bothering me that i can see it and i feel like it will affect my phone eventually...
Click to expand...
Click to collapse
I believe this is a design/quality issue. I posted about this same problem here some weeks back. HTC will not repair under warranty, paid in total 77 pounds to get this fix from them. I believe they are aware this is a problem because in the warranty book, screens are not covered even when its not your fault. They call it Newton ring .
Funny thing that a lot of people started noticing this issue very recently: as if a cheap component came to the end of its life cycle.. propably in my head only..
Anyway: I noticed this on my TP a few days ago and I'm going to drop my phone to the local service. It's the second time in just over 4 months.. crappy build quality really
also: Diamond users have had the same issue: http://forum.xda-developers.com/showthread.php?t=439410
Local HTC service got back to me: they're insisting that it's a 'mechanical fault, not covered by the manufacturers warranty'. Then it gets better: the estimated repair cost is 275 euros (that's roughly 355 USD) for the replacement of the display and front cover.
Naturally I'm going to challenge this as the oily patch appeared over night when the phone was sitting on a table.
not that im questioning what happened but personally i find it difficult to imagine how it can get the oil spot just by sitting on the table :S
normally you would expect this after exserting enough force on the screen. Personally that was my case. I sort of fell asleep on the phone and might have hit it on the metal edges of the bed..anyway i got mine replaced from pdatech.nl for ~170euros including installation costs..
Well if I had to venture a guess, I'd say that the 2h navigation on the night before took its toll on the display and during the night it just spread out and became visible..
how dodgy. I have been getting this problem, but funnily enough I thought it was due to air pressure, because it happened to mine when i was on the plane.
anyway i was just coming home from someplace real hot (40C), and it kept giving me the screen alignment problem for a few weeks, kept thinking i was pressing the top right corner of the screen regardless where I pressed. However, found that putting slight pressure on the screen for a few hours (i.e. a weight) fixed the screen alignment problem temporarily (for a few hours).
Anyway, just came back on the plane from someplace real cold (-10C), now the problem has ceased.
???? air pressure? or temperature variation?
I don't have the screen oil spot problem you guys have however.
Here's to it lasting a little while longer...
I asked for a more detailed report of the fault and the service just said that 'It's a fault defined as OOW (Out Of Warranty) by the manufacturer' and that there's nothing they can do but charge me for the repair. Note: they're not even putting the blame on me saying 'abuse/misuse'!
Now I'm going to go to the seller (expansys) and hope that they have some interest in keeping customers happy (and maybe have more business with them in the future!) and make things right (=fix my phone or replace it).
Wow, and I thought I was the only one. I've noticed the same oily stain after falling asleep on the phone. I've had it for a month now, and I've gotten used to it. It does not seem to affect the sensitivity or the accuracy on the touch screen. At least not in my case.
Does anyone have any experience replacing the touch screen by themselves? Is it a complicated operation? I would greatly appreciate a 10-step-guide on how to replace the screen, if it's going to be an issue over time.
disassembly guide
check out the wiki of xda click on service manuals and look for raphael. its on page 19 of the PDF
I noticed this issue on my Touch Pro today morning! I used my phone last evening and everything was fine. Now the touch screen doesn`t work at all. Great.
Same issue
I have also been victim of the oily patch.
I have had the Sprint Touch Pro since November and it just happened within the past 2 weeks.
Maybe this is due to not putting the screen protector on the phone.
I'm going to try visiting the Sprint Repair Center to replace it and then put the InvisibleShield Screen Protector on it.
Okay strait to the point! I've got a Galaxy S2 with Android 4.0.3 bought it 4 months ago.
I accidently dropped my phone and cracked my screen on the bottom right corner. The crack went from bottom and a diagonal line up til the right side. I took a picture below.
imageshack(.)us/photo/my-images/685/20120326152703.jpg
This happened about 2 months ago. No problem since. I dropped the phone a few times afterward but it didnt seem to affect it lucky me.
Yesterday i tried watch some series over my WIFI and the phone got really hot around the camera area. The phone wasn't acting well either and then battery dropped from 75% til about 10% in 10 minutes without any video still showing up. (Never had that problem before). I stopped using it and instead put it on recharge for the next day. And today on the morning it was still okay. Went to school and back with the mobile still working. Put it on my table and checked my PC.
About 2 hours later while cheking up on my galaxy i discovered this.
imageshack(.)us/photo/my-images/198/20120326153629.jpg
I think that the LCD finally busted but i need to be sure if it has something to do with the previous crack and also if you could provide any info about what to do with it? Does my warrenty cover this? Or do i need extra insuranse?
I really need help right now LCD blackned spots
The screen has started to turn black from the core of the LCD leak. I now really think this is a broken LCD screen and not a software problem. If someone knows what i could do to fix this i really could need the help right now.
Someone correct me if I'm wrong,
But it sounds to me like you've busted the digitizer portion of your device. As to it being caused by the small crack on your screen.. i don't really know(can't really see if it's a crack in the glass or digi). At any rate, judging from the second picture you provided us it most definitely looks like you damaged the digitizer.
Most companies don't really cover damaged screens caused by users. However, being that your S2 is only 4 months old you could possibly pass it as "it did it by itself, I don't know what happen". Worth a shot I guess...
If all fails you could bring it to a electronics repair shop or you can repair it yourself via a digitizer part bought on ebay(probably pretty expensive being that its part of the screen)
If all else fails check ebay for a new screen.
cbr69er said:
If all else fails check ebay for a new screen.
Click to expand...
Click to collapse
http://www.ebay.com/itm/Full-LCD-Di...ltDomain_0&hash=item27c3101beb#ht_1618wt_1185
If your thinking about taking the DIY road I found a screen for you.Quick note about buying something overseas on eBay: it usually takes awhile for the part to ship and even when you get it, the part may not be functional. But don't fret, eBay is usually pretty good about stuff like this so a working part will be guaranteed or your money back!
If you do decide to repair it yourself I would first research A LOT about your phone. Especially, the disassembly guide! Try to use only credible guides such as iFixit, repair universe etc.
This only applies to flex ribbon cables:
when replacing screens sometimes you have to plug it in a few times before you actually get it to respond(could be cause by oxidation of the pins) if thats the case, you could try to take a #2 pencil eraser and gently rub against the pins and remove the oxidation...
Good Luck!
Please let me know how it goes!
rhodium9 said:
As to it being caused by the small crack on your screen.. i don't really know(can't really see if it's a crack in the glass or digi).
Click to expand...
Click to collapse
Yes it is really a crack and a very annoying one. It doesn't cause any problems with the touch-function, so I've been using it normally but for the screen, it has gone completely black but for the top right part still a little darkblue. I think I'm going with your first answer and try to check it in on warranty have had a bit luck with it past couple of times but im not sure about changing it myself. If having no luck with warranty then maybe ill try doing it myself.
at any rate weather you get warranty to change it or you fix it yourself maybe youll learn to be more careful and get a case maybe???
Hi Guys
I've seen a couple of posts about this on forums but, I've had a similar thing to a few users now, where I have 2 circles of "Dead" pixels appear on the phone.
Seemed to appear suddenly today at work. I've not dropped the phone (today) but, I have had it in my pocket when getting out the car and, it might have been caught between my leg and steering wheel of the car.
I know there's been some suggestions of placing the phone in a carrier bag and, then in the fridge for a couple of hours (well, couple of hours to a weekend). I'm a bit nervous of this but willing to give it a try.
Just wondering though, does anyone have any explanation for why this happens? I can't see it being physical damage to the screen, as otherwise there would be whole columns of dead pixels or spider patterns with a crack. In the middle of the circles, it seems to be sub-pixels that are out (Blue / Red - Green seems to be OK). Also, has anyone else had the same experience and tried putting the phone into the fridge and, does this work? Annoying though it is, I'd rather live with it than knacker the phone totally lol.
I've attached some pictures to demonstrate what I mean... Note, on the blue one, it looks as though there's a pentagram dotted in the lower circle... Satanic Possession? lol
Kind Regards
Daryl
Well,Nothing of those homemade methods will help
maybe the screen got pressed too hard..got hitted by something..
take it to a lab
Probably just enough pressure and maybe battery and body heat, did the same with my Acer and a till reciept scrunched up so now have a multi-coloured circle in centre of screen... doubt there's a fix except replacing it
Rooted Xakep E320/C6 EUU Hacked Update
Thanks for the feedback on this. I think you're both right. The screen is slowly getting worse. The sub-pixels in the middle of the circles have repaired themselves but, the horizontal lines of dead pixels are slowly expanding horizontally across the screen.
I think I'm going to have to face the fact that its broke and see about getting a new screen fitted. I'd normally do it myself but, I've seen how well the digitizer and LCD are glued together, and to the case lol (HTC Sensation).
Am thinking it has to be a pressure 'injury' when getting out the car and, maybe it got trapped between my leg and the steering wheel.
The good news though, at least I have an excuse to nick my tablet back off my son lol
Well... bugger me rigid lol. As I was typing my last message, I thought "sod it, I may as well try putting the phone in the fridge to see if it does any good" After all, I had nothing to lose (as long as I was careful of condensation on the warm up) and... it does actually seem to be having a positive effect!!
Attached 2 more pics... One was taken at work at 3pm, one was taken after 80 minutes in the fridge at 11:30pm (note, the screen had gotten a little worse between 3pm and 10pm).
I've put it back in the fridge for another couple of hours and, will post an update on progress.
Ever the optimist once more
lol at the pentagram. Yeah it's probably because of pressure or some other physical damage. Do you have warranty?
Nope, the phone is 18 months old, I rang 3UK and, apparently the warranty is only 12 months so, bummed out there.
Have got the phone back in the fridge after noticing how much of an improvement the first blast of cold air made to it lol. Fingers crossed. I can't believe such a simple thing might actually make it better again
Bummer. Have a hard time seeing the fridge as a permanent solution, yeah you could always try ifixit if you think it's worth a shot.
This is true, I cant see it being permanent either. I did take a look at replacing the screen on YouTube and, it seemed like a straightforward enough task but, not sure about the whole glue thing between motherboard and screen, and screen / digitizer. I know it'll need heating to melt the glue a little but, the video I saw indicated that his heat gun was at 420 degrees Celcius... the psycho!!
Am hoping I can get another 6 months out of the phone, so that I can get an upgrade to a One X / Galaxy S3. I've really loved the phone and, will be sad when it eventually goes.
Just to give anyone interested a bit of a status update... Just about to go to bed and, need the phone for my alarm in the morning so, pulled it out of the fridge again lol.
As you can see from the attached though, it does seem to be still improving.
Going to run the dead pixel fix app overnight (not that I believe this will do anything spectacular) and, may do another round in the fridge tomorrow night. Of course, I will keep you posted.
For now though, the latest comparison - between 11:30PM (the improvement I posted earlier) and 1:30AM. Once again, you can see that the dead pixels do seem to be returning to life.
Well from the pics I'm gonna try it myself not looked up how the screens are made up but the cold could be doing several things as shrinking membranes (those touching may separate) and crystallizing the LCD (expanding the Liquid Crystal) to fill the gaps made at the pressure point, that's my guess so throwing it in the freezer tonight
Thanks for continued updates
Rooted Xakep E320/C6 EUU Hacked Update
I probably wouldn't recommend throwing it into the freezer. Just a gut feeling but, as the temperature in there is well below freezing, I think it would do more damage than good. At least in the fridge, it's only around 4 degrees C so, technically still within the operating temperature range of the device.
Also, when you do take it out, make sure you don't just throw the battery straight back in. As soon as it comes out, it gets quite a hefty amount of condensation on it. The last thing I would want is for something to short on the device when it gets its power back and fry your logic board :s
Not much improvement on last night in running the LCD fixing application (as I thought) so, thrown it back into the works fridge - much to the amusement of works colleagues lol. I'll take it back out around lunch time, see how it is, and post the comparison between 1:30AM last night and lunchtime today...
Fingers X'd
Latest on phone: My director at work advised I should check on operating temperatures of the phone to see how cold I could take it safely. Turns out that they are electronically safe at temperatures of up to -40 degrees C (although there's no way I would actually test this and wouldn't recommend testing it to anyone).
Following from this, I put it in the freezer at work for an hour (after being in the fridge at work for 2).
Not posted the before picture but, here's three pictures of how it looks at the moment. One on a pure white screen then, to demonstrate that it's not just the pixels being stuck white instead of not working, I have also done a shot of my home page, and a shot from a game.
I have a doubter at work who stated quite daringly that he would eat his underpants if the cooling of the phone worked... Now... All I need to do is prove why it's worked, then find some recipe's for Underpant Madras... any suggestions as to both would be appreciated lmao
Googling now and second post gives this http://forum.xda-developers.com/archive/index.php/t-687247.html I'll see what else pops up and add to this posting here
Wiki lol -> http://en.wikipedia.org/wiki/Touchscreen <- I guess from this and type of screens now being used it's an adhesive layer between the back and front glass that is 'spread out' so no separation between back and front conductors, freezing may crystallize the adhesive and on warming the original surface pressure may force the adhesive back and conductors are separated again ;-)
Rooted Xakep E320/C6 EUU Hacked Update
Just noticed my own screen (or rather noticed it less lol) my spot has gone, although not as bad as your own screen only colour swirls on screen pressure no black/white pixels, I did have my phone slide and bounce off my knee that may have been enough for mine lol was looking forward to fridging it this I will be remembering though
As for a recipe for the grundigs i'd serve them raw .... 3 days worn .... why make it easy lol
Rooted Xakep E320/C6 EUU Hacked Update
Right it came back not as bad so I'd recommend a hard front cover, bit of a bind if they don't flip but it's that or faulty screens
Rooted Xakep E320/C6 EUU Hacked Update
Hi
Been a little while since my last update so, checking in. I don't have any extra pictures at the moment but, the cold is really starting to make a big difference.
I took it out the ice-making compartment at work at lunchtime and, the screen is mostly repaired. I would say about 5 - 6 dead pixels in a line now, around where the "beak" was on my satanic chicken (lol)
It's still in the fridge at home at the moment and, will probably stay there most of the weekend. This last bit is being quite stubborn to shift but hoping that it does shift and, when it does, it goes for good.
I'll let you know how it goes anyhow. I'm simply stunned by the improvement so far though
Yayyyyyyyy!!!
Well, the great news is the phone is now completely 100%
I've attached a photo of the screen with my home wallpaper on it... The trouble is, I can't remember exactly where the fault was so I can't get the exact same screen so, I've taken a wider shot which still demonstrates that there are no dead pixels.
I did have a bit of trouble getting Wifi and the SD card to read when I first powered back up from the latest (4 hour) stint in the freezer but, whipped the battery straight out and let it settle back to room temperature some more, then used a hairdryer just to ensure that any last bits of condensation had cleared up.
Fully working phone once again. I think I'll serve underpant soup at work on Monday lmao.
Thanks for following this little thread that I'd done and thanks for your input too. It's certainly been an interesting journey and, hopefully someone else with a similar problem can benefit from my experience too.
Kind Regards
D
What a cool way to fix your phone I have a Nokia 6303 classic with dead pixels. I will place in the fridge overnight and wait for the results next morning.
Good to hear it's running again, bear in mind it wont take as much to bring the fault back if pressure is applied again but from my own phone it does wear off so repeating the damage is repairable but will probably shorten it's life.
And please by all means post the pics of the garnished garment meal
Rooted Xakep E320/C6 EUU Hacked Update
Im wondering if other people's 8X's creak when squeezing the phone sideways or on the screen after a few minutes of use? Also I can see light leaking from the bottom where the screen meets the body of the phone. Want to know if I should get an exchange tomorrow at Microsoft Store since after that I'm pretty far from any Microsoft Stores until I'm past the return date.
My volume rocker squeaks a little and also moves back and fourth when I shake the phone. At the bottom of the phone on either side of the charging port there are light leaks, and on the left and right bottom sides too, which is annoying in the dark. Tempted to take mine back to Phones4u and ask for a new one..
Got a new phone and its much better. I didn't notice if light leaks through bottom anymore, but the screen is definitely more flush though not PERFECTLY flush.
Much more solid phone and power button also has a click and is easier to press now. No more creaks now.
Sent from my 8X using Board Express
I'll go and exchange mine then I think. Can you take a picture of it in the dark to show if you have any light leaks and post it up? I'd be very appreciative.
My power button feels a bit odd too, it doesn't have a click and feels squidgy, was thinking that earlier. Might have a go on the replacement in store and look at it in the dark to check for light leaks.
Edit: I've attached the best picture I could get of my light leaks/screen fitting. This is with brightness at max, taken with my DSLR. Was yours this bad? I'd be interested to see if this is an issue with other 8X's or just ours.
I haven't had any problems like that with mine yet. I started using a case after the first week though. Hopefully a replacement will fix the issue for you. That's a lot of light coming through.
Sent from my HTC 8x using Board Express
It is, it's awful. I'm kind of regretting getting the 8X over the 920 to be honest, the blacks seem very light on the screen and the colour seem very washed out (maybe it's just coming from an AMOLED screen that is doing it), might see what they can do for me in store today. We'll see.
Took it back today, they didn't want to replace it but they did in the end. Tried out two brand new Yellow ones in store, both had the exact same issue. Tried a black one, and it's perfect, no light leakage at all. Maybe it's an issue with the Yellow one. Poor effort HTC.
Accepted the Black one as a replacement, but I'm trying to sell it and get a 920 like I should have in the beginning. Doh!
SmokinWaffle said:
Took it back today, they didn't want to replace it but they did in the end. Tried out two brand new Yellow ones in store, both had the exact same issue. Tried a black one, and it's perfect, no light leakage at all. Maybe it's an issue with the Yellow one. Poor effort HTC.
Accepted the Black one as a replacement, but I'm trying to sell it and get a 920 like I should have in the beginning. Doh!
Click to expand...
Click to collapse
Meh. I have the black one and its an issue all right. Yesterday, my screen totally died. Went to HTC service center today, and the light leakage and inperfect screen flush were listed as "possible user damage". If they decide to classify it as user damage, i'll be pissed.
matthew5025 said:
Meh. I have the black one and its an issue all right. Yesterday, my screen totally died. Went to HTC service center today, and the light leakage and inperfect screen flush were listed as "possible user damage". If they decide to classify it as user damage, i'll be pissed.
Click to expand...
Click to collapse
I went with the 920, had screen flickering issues and random rebooting on it, and all 3 of my replacements. Gave up and got a Note II. lol.
Yes, when I had mine it creaked and the camera lens moved around a little, and the screen was a tad squishy on the bottom right...HTC consistently has awesome designs but
There is always something wrong with their build quality that is maddening.
Sent from my DROID RAZR HD using xda app-developers app
Crack over Speaker holes
Hi guys, just to add to the build quality problems... I've just had a replacement from Phones4U of my yellow 8X. After just under a month of gentle and careful ownership i noticed a crack appeared over (and through) the holes on the back for the speaker. The crack got bigger over about a week before i had chance to go ask about it in store. to be fair to P4U, the person i spoke to was great and they swapped it out in store, even though i'd originally bought it online.
Came back to this thread to mention it and now having read everything else i'm noticing a bit of creaking when i squeeze the sides and both phones had had the squishy screen edge picture thing which i first read about being a problem on the ONE X. Not sure if that's just normal anyway though really. Oh and neither of my power buttons have clicked and i find myself missing my easy to press home button on my old iPhone 3GS!
Same again!
natstally said:
Hi guys, just to add to the build quality problems... I've just had a replacement from Phones4U of my yellow 8X. After just under a month of gentle and careful ownership i noticed a crack appeared over (and through) the holes on the back for the speaker. The crack got bigger over about a week before i had chance to go ask about it in store. to be fair to P4U, the person i spoke to was great and they swapped it out in store, even though i'd originally bought it online.
Came back to this thread to mention it and now having read everything else i'm noticing a bit of creaking when i squeeze the sides and both phones had had the squishy screen edge picture thing which i first read about being a problem on the ONE X. Not sure if that's just normal anyway though really. Oh and neither of my power buttons have clicked and i find myself missing my easy to press home button on my old iPhone 3GS!
Click to expand...
Click to collapse
Well after a month (again) my replacement 8X has developed the crack in the same place.
Phones 4U are gonna swap it for a black model this time, i'm wondering if it's the yellow plastic specifically that's bad. They were less cheery and helpful with the exchange this time stating that because it's a cosmetic fault they don't usually replace them and the first time was 'a goodwill gesture'.
I'm starting to wish i'd just gone for the extra price bump for the Lumia 920 instead now. Guess i'm lucky they've replaced them at all though but i still don't think a phone should crack of it's own free will after 4 weeks! http://forum.xda-developers.com/images/icons/advanced/drive.png
They also said it's not a widespread fault that they've been made aware of, i was actually hoping someone else on here would have had the same experience to help me confirm it wasn't just bad luck or whatever. I guess everyone else just has the corners rubbing off instead!
I guess I got lucky, my blue 8X seems pretty solid and all the buttons are clicky.
Hi Guys,
First post so go easy. Lurked the boards for a while now but only just registered. Hoping some one can help me out a little here, as I'm at my witts end now.
So I bought my xoom (MZ604..?) back in february second hand for £125 posted, it's a the 10.1" version and it's running android ICS. I bought it as i love my Samsung galaxy tab 7 but i think it lacks the screen size and the xoom seemed like a great price for a larger equivalent. I used it pretty much every day and it was awesome, never had any problems with it until...
My son decided to kick it off my lap onto the granite fireplace. The screen instantly went black and just didn't do anything. I could see a faint bbacklight on inside so I assumed it was the LCD panel that was broke, i could still here notifications and if i swiped in the right place i could also hear the tablet unlocking so the digitizer was ok too. I bought a water damaged xoom off ebay and harvested the screen to try and replace it and that wen ok, except i still had the same problem so I assumed that screen was broken too, oh well spares and repairs doesn't always work out lol...
So I bought a brand new LCD panel and fitted that yesterday, and it STILL won't work. However, the issue i now have is it won't turn on at all. I've taken it apart and put it back together multiple times to make sure it's all gone back in the right place etc. It's also charging ok, i put it on the dock and the light goes white, and then green after a while.
I'm at a loss here, as the new screen and xoom cost me nearly £100 so it's not really worth me paying any more as it's begining to seem like an endless pit of money.
TLDR:
Bought xoom
Son dropped xoom
Screen went black but tablet still worked
Bought 3nd hand xoom and swapped lcds
No joy with that
Bought brand new screen
charges but won't turn on now
Hoping someone on here can help me, i really don't want to throw it away as it's a fantastic device, but at the same time i can't keep plowing money into it if it won't work.
Thanks guys,
Uv.