EDIT: Random success with Verizon tool No idea what changed...
This is what I was seeing when I tried to use the Odin method of unbricking, it would get ~halfway done and then fail.
Tried again with the PIT file and again failed about 50% of the way through.
4.3
Product Name: SCH-I535
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Official
Qualcomm Secureboot: Enable
Warranty Bit:0
Bootloader RP Swrev: 1
I then tried the Verizon Assistant method and it got to 86% then said my device was disconnected unexpectedly and I get this.
Product Name: SCH-I535
Current Binary: Samsung Official
System Status: Official
Qualcomm Secureboot: Enable
Bootloader RP Swrev: 2
Decided to try once more and ended up seeing this in all red letters
sw rev check fail : Fused 2 > Binary 0
I then tried using this method to unbrick http://forum.xda-developers.com/showthread.php?t=1840030 and Odin fails when I try to push the bootchain.
Message log from Odin when I push the bootchain
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRALEC.bootchain.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I'm at a loss here I don't care what I have to update to but I've spent hours trying to solve this mystery any assistance would be greatly appreciated. I can still get to the download screen so I'm not hardbricked.
I am trying to flash a stock ROM onto my SM-G930F using Odin3 v3.10.7 . I am in the United Kindom and the phone is H3G. I have tried 3 different ROMS from sammobile but none will flash onto the device. I can now only get into download mode.
On the device it says
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-G930F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: ON
Secure Download: Enabled
WARRANTY VOID: 0 (0x0000)
RP SWREV: B:1 K:0 S:0
None of the text on the phone changes whilst flashing.
The log on Odin is:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
I have also tried using the "Firmware and initialization" tool in Samsung Kies 3 but get the error "failed to upgrade firmware due to an unexpected error".
Any help would be greatly appreciated.
Tried different usb cable? (Especially try the one that came with your phone)
Tried a different USB port? (no hub in between)
Tried different drivers?
Tried different computer?
edit: maybe this works: http://androidforums.com/threads/resolved-soft-bricked-cant-flash-with-odin.473420/
LowLatency said:
Firstly, I know this is posted under S7 Edge but couldn't find a Q&A topic for the S7.
I am trying to flash a stock ROM onto my SM-G930F using Odin3 v3.10.7 . I am in the United Kindom and the phone is H3G. I have tried 3 different ROMS from sammobile but none will flash onto the device. I can now only get into download mode.
On the device it says
ODIN MODE
DOWNLOAD SPEED: FAST
PRODUCT NAME: SM-G930F
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FRP LOCK: ON
Secure Download: Enabled
WARRANTY VOID: 0 (0x0000)
RP SWREV: B:1 K:0 S:0
None of the text on the phone changes whilst flashing.
The log on Odin is:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> param.bin
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> __XmitData_Write
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
I have also tried using the "Firmware and initialization" tool in Samsung Kies 3 but get the error "failed to upgrade firmware due to an unexpected error".
Any help would be greatly appreciated.
Click to expand...
Click to collapse
Hi mate
Did you unlock your bootloader? , try it with a newer Odin
check this thread , there are step by step instructions
http://forum.xda-developers.com/galaxy-s7/how-to/official-stock-firmware-update-odin-t3369431
MAX 404 said:
Hi mate
Did you unlock your bootloader? , try it with a newer Odin
check this thread , there are step by step instructions
http://forum.xda-developers.com/galaxy-s7/how-to/official-stock-firmware-update-odin-t3369431
Click to expand...
Click to collapse
How do I unlcok the bootloader? Is this by turning on developer options? I couldn't access the settings so was unable to do this if so.
LowLatency said:
How do I unlcok the bootloader? Is this by turning on developer options? I couldn't access the settings so was unable to do this if so.
Click to expand...
Click to collapse
Unlocking the bootloader is when you go into your SETTINGS/ABOUT DEVICE and tap the build number until you get a message that you have unlocked the developer options. You then back out of ABOUT DEVICE and enter DEVELOPER OPTIONS and enable OEM UNLOCK. Did you do any of that?
I think this may be progress. My phone now boots into Recovery where at the top it says:
Android Recovery
MMB29K.G930FXXU1APC8
samsung/heroltexx/herolte
6.0.1/MMB29K/G930FXXU1APC8
user/release-keys
I think this is showing a ROM that I flashed onto it in an attempt to fix the problem but it didn't work.
Then has all the options for recovery.
At the bottom it says
Supported API: 3
dm-verity verification failed...
E:failed to mount /system (Invalid argument)
I have tried a few different ROMS that I have on my computer through Odin v3.11.1 (I believe the newest version) but to no avail.
As you can probably tell, I'm not 100% sure what I am doing but have worked out that it is the main file that goes under AP in Odin that is the problem.
I am about to try the upgrade tool in Kies now I can get into recovery mode and see if that works.
kettir said:
Unlocking the bootloader is when you go into your SETTINGS/ABOUT DEVICE and tap the build number until you get a message that you have unlocked the developer options. You then back out of ABOUT DEVICE and enter DEVELOPER OPTIONS and enable OEM UNLOCK. Did you do any of that?
Click to expand...
Click to collapse
I hadn't done this no, because the phone bricked whilst I was updating it through Kies. After the update failed I couldn't get back into the phone at all other than "download mode" so this wasn't an option.
Update!
My phone still won't update through Kies. I'm still getting the same error message
LowLatency said:
I think this may be progress. My phone now boots into Recovery where at the top it says:
Android Recovery
MMB29K.G930FXXU1APC8
samsung/heroltexx/herolte
6.0.1/MMB29K/G930FXXU1APC8
user/release-keys
I think this is showing a ROM that I flashed onto it in an attempt to fix the problem but it didn't work.
Then has all the options for recovery.
At the bottom it says
Supported API: 3
dm-verity verification failed...
E:failed to mount /system (Invalid argument)
I have tried a few different ROMS that I have on my computer through Odin v3.11.1 (I believe the newest version) but to no avail.
As you can probably tell, I'm not 100% sure what I am doing but have worked out that it is the main file that goes under AP in Odin that is the problem.
I am about to try the upgrade tool in Kies now I can get into recovery mode and see if that works.
Click to expand...
Click to collapse
Hi mate
First of all "OEM unlock" is not necessary to odin flash a stock rom...please forget i said it
The issue seem that is caused by dm-verity verification failed , same symptoms .. keeps device in boot loop ( Samsung Logo) , not sure yet what the solution is i seem lots of threads about it on S6 and Note 5
Check this thread:
http://forum.xda-developers.com/showpost.php?p=66605862&postcount=48
@CuBz90 with a S7 had the same problem and mention it did not work........maybe he can help out
In the same thread they suggested this..you could try it ..just in case
http://forum.xda-developers.com/showpost.php?p=67217747&postcount=52
Only thing i got for now......
With frp lock on and drm error. There is no way around it at the moment.
Sent from my SM-G935F using Tapatalk
CuBz90 said:
With frp lock on and drm error. There is no way around it at the moment.
Sent from my SM-G935F using Tapatalk
Click to expand...
Click to collapse
Thanks for replying mate
Bad news indeed......in your case you had knox bit tripped off?
I see that twrp recovery
http://forum.xda-developers.com/galaxy-s7/development/recovery-official-twrp-herolte-t3333770
Has a
If you only want a bootable system partition or writable data in TWRP:
Download dm-verity and force encryption disabler.
Without exiting TWRP, transfer no-verity-opt-encrypt.zip to your device over MTP* and flash it using [Install] in TWRP.
I know it means to trip knox , but i wonder if it would help
MAX 404 said:
Thanks for replying mate
Bad news indeed......in your case you had knox bit tripped off?
I see that twrp recovery
http://forum.xda-developers.com/galaxy-s7/development/recovery-official-twrp-herolte-t3333770
Has a
If you only want a bootable system partition or writable data in TWRP:
Download dm-verity and force encryption disabler.
Without exiting TWRP, transfer no-verity-opt-encrypt.zip to your device over MTP* and flash it using [Install] in TWRP.
I know it means to trip knox , but i wonder if it would help
Click to expand...
Click to collapse
No because with frp on you cannot flash twrp
Sent from my SM-G935F using Tapatalk
CuBz90 said:
With frp lock on and drm error. There is no way around it at the moment.
Sent from my SM-G935F using Tapatalk
Click to expand...
Click to collapse
How annoying, hopefully somebody finds a fix soon
LowLatency said:
How annoying, hopefully somebody finds a fix soon
Click to expand...
Click to collapse
Just one thing I noticed in your posts, you refer to Kies 3 if you are trying to do it with Kies 3 this isn't compatible with the S7, if you don't need it uninstall it and install Samsung Smart Switch, this will install the correct drivers for the S7, you may be able to get the Initialization and Recovery process to work then.
The problem with Odin is if you don't have USB Debugging enabled it wont work, also you system status says Custom this can prevent Smart Switch from working as well but give it a try you have nothing to lose
I have the same problem.
What damages drk?
ag4751 said:
Just one thing I noticed in your posts, you refer to Kies 3 if you are trying to do it with Kies 3 this isn't compatible with the S7, if you don't need it uninstall it and install Samsung Smart Switch, this will install the correct drivers for the S7, you may be able to get the Initialization and Recovery process to work then.
The problem with Odin is if you don't have USB Debugging enabled it wont work, also you system status says Custom this can prevent Smart Switch from working as well but give it a try you have nothing to lose
Click to expand...
Click to collapse
Still no luck using Smart Switch, I get the same error message as with Kies.
As you say, it was worth a try, so thanks!
Anyone have a fix for this? I ran into the same thing. Mistakenly (like an idiot) reset all of my settings before using Flashfire to flash an OTA update. The result is the same as the OP. Tried using Odin to flash stock, running into failures and the same dm-verification problem.
bump
I semi bricked mine not long ago I just put it in download mode plugged it in to my win 10 laptop and flashed twrp with ordinary then flashed stock rom
Sent from my SM-G930F using Tapatalk
I cannot flash anithing. All tries ended up in a fail. (Complete write operation fail).
Looks like the samsung protection blocked the Boot.
So I went to root the phone and I did so with CF Auto Root. I went into Super Su and decided it was not what I was looking for. I was hoping for more of a GUI TWRP system and decided to unroot and factory restore the phone. I'm stressed to the point where i have no memory of how the phone got screwed up at this point. Here is what I do know.
When I power the device on normally it is frozen at the Samsung Galaxy S6 boot page and at the top it says KERNEL REV CHECK FAIL DEVICE 3 BINARY 2. Is this because I have the wrong firmware on the device? Is there any way I can get the bootloader, the firmware and everything else and just restore everything at once? Samsung Smart Switch fails to recover the device and I would absolutely love to do an emergency recovery, but it keeps asking for a code from a previous computer and I have no idea what it's talking about.
Any help would be appreciated.
jblevins1991 said:
So I went to root the phone and I did so with CF Auto Root. I went into Super Su and decided it was not what I was looking for. I was hoping for more of a GUI TWRP system and decided to unroot and factory restore the phone. I'm stressed to the point where i have no memory of how the phone got screwed up at this point. Here is what I do know.
When I power the device on normally it is frozen at the Samsung Galaxy S6 boot page and at the top it says KERNEL REV CHECK FAIL DEVICE 3 BINARY 2. Is this because I have the wrong firmware on the device? Is there any way I can get the bootloader, the firmware and everything else and just restore everything at once? Samsung Smart Switch fails to recover the device and I would absolutely love to do an emergency recovery, but it keeps asking for a code from a previous computer and I have no idea what it's talking about.
Any help would be appreciated.
Click to expand...
Click to collapse
https://forum.xda-developers.com/galaxy-s6/help/how-to-smart-switch-emergency-t3383448
There you go..
brenner650 said:
https://forum.xda-developers.com/galaxy-s6/help/how-to-smart-switch-emergency-t3383448
There you go..
Click to expand...
Click to collapse
I have already done this. It failed. I need help getting into Emergency Recovery. This is just Recovery.
jblevins1991 said:
I have already done this. It failed. I need help getting into Emergency Recovery. This is just Recovery.
Click to expand...
Click to collapse
Is your device SM-G920F?
forumber2 said:
Is your device SM-G920F?
Click to expand...
Click to collapse
It's the sm-g920t.
jblevins1991 said:
It's the sm-g920t.
Click to expand...
Click to collapse
So, your phone should be T-Mobile.
Download and run this;
https://forum.xda-developers.com/attachment.php?attachmentid=3803841&d=1467715462
When you open the program, type the values given here;
Model: SM-G920T
Region: TMB (write XAR here if your phone is not T-Mobile variant)
Auto: Selected
Manual: Unselected
Binary Nature: Selected
Check CRC32: Selected
Decrypt automatically: Selected
When you write and select options given above, press "Check Update" and then press "Downlaod" to download factory firmware for your device.
Once the download has been finished, extract the zip file that you've downloaded via SamFirm.
After unzip it, download and run this;
https://forum.xda-developers.com/attachment.php?attachmentid=3804544&d=1467772303
When you open it, press BL and select file which starts with BL from downloaded (from Samfrim) and extacted zip folder.
Do the same thing for AP, CP, CSC.
When you set 4 files to Odin, connect your phone to your PC in download mode and click "Start" on Odin.
forumber2 said:
So, your phone should be T-Mobile.
Download and run this;
https://forum.xda-developers.com/attachment.php?attachmentid=3803841&d=1467715462
When you open the program, type the values given here;
Model: SM-G920T
Region: TMB (write XAR here if your phone is not T-Mobile variant)
Auto: Selected
Manual: Unselected
Binary Nature: Selected
Check CRC32: Selected
Decrypt automatically: Selected
When you write and select options given above, press "Check Update" and then press "Downlaod" to download factory firmware for your device.
Once the download has been finished, extract the zip file that you've downloaded via SamFirm.
After unzip it, download and run this;
https://forum.xda-developers.com/attachment.php?attachmentid=3804544&d=1467772303
When you open it, press BL and select file which starts with BL from downloaded (from Samfrim) and extacted zip folder.
Do the same thing for AP, CP, CSC.
When you set 4 files to Odin, connect your phone to your PC in download mode and click "Start" on Odin.
Click to expand...
Click to collapse
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin engine v(ID:3.1203)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> sboot.bin
<ID:0/008> param.bin
<ID:0/008> cm.bin
<ID:0/008> boot.img
<ID:0/008> recovery.img
<ID:0/008> system.img
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
<ID:0/008> Added!!
This is the log when I tried your solution. Any ideas?
jblevins1991 said:
<ID:0/008> Added!!
<ID:0/008> Removed!!
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin engine v(ID:3.1203)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> SingleDownload.
<ID:0/008> sboot.bin
<ID:0/008> param.bin
<ID:0/008> cm.bin
<ID:0/008> boot.img
<ID:0/008> recovery.img
<ID:0/008> system.img
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Removed!!
<ID:0/008> Added!!
This is the log when I tried your solution. Any ideas?
Click to expand...
Click to collapse
Try with another usb cable, another usb port or another PC.
I bought an official samsung charger and fixed it. I think the old charger was disconnecting during the smart switch initialization process.
Any way to fix knox?
Hey all,
Tried flashing back to stock firmware using my Galaxy S4 GT-I9505 using Odin but im getting this error relating to a pit file. I have googled it and downloaded a few pit files for the specific phone but its still not working.
I have flashed previous devices with this flash tool before with no issues usually just have to click AP and browse to the selected firmware click start and shes golden and it works no dramas. However with this device im having soo much bad luck. I have tried to pull my pit file using Miracle box however that doesnt work either, Ive also tried to pull it using ADB but I need ROOT and I dont have it on this device either. I have also tried to root with odin too and I get the same error. is there another program that I can use to pull my own pit file?
I have copied the Odin Log for a reference so hopefully someone can shed some light on this annoying issue cheers.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7105TDVUEMK2_N7105TXSAEMK3_N7105TDVUEMK3_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Hello everyone,
My old phone starting to do some weird things: on power on, it doesn't respond. If I put it in charge, it reboots continuosly, by vibrating and showing the Samsung logo for a fraction of second. I don't know why.
I'm able to put it in download mode, but if I try to flash a stock rom, odin doesn't works.
I downloaded this rom from sammobile: G355HNXXU0AQA1_G355HNITV0AQA1_G355HNXXU0AQA1_HOME Italy Android 4.4.2
Putted into Odin 3.13 in the section AP, I tried to flash but the message was "There is no PIT Partition". Options enabled: "AutoReboot, F.ResetTime".
Second attempt: Options enabled: "AutoReboot, F.ResetTime and Re - Partition", same firmware. Result: operation failed.
Third attempt: changed the cable and the firmware, with: G355HNXXS0APH1_G355HNITV0APF1_G355HNXXU0APE1_HOME
It doesn't works. My log is:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1301)..
<ID:0/005> File analysis..
<ID:0/005> Total Binary size: 1105 M
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
No pit file used during the procedure, only the firmware as AP.
Any help?
Thanks in advance
UP! Please, nobody?
Same problem
My odin do the same!!! Please help