[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=1 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=2 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=3 rdata=5AA5
[PMIC_WRAP]wrap_init pass,the return value=0.
pl pmic init start
pl pmic efuse start
pl pmic efuse BUCK trim
[0x1C8]=0xF802
[0x1CA]=0x807F
[0x20E]=0xE0
[0x260]=0xF0
[0x286]=0xF0
pl pmic efuse end
pl pmic en rst [0x126]=0x13
[0xE]=0x1
[0x540]=0xA0
Battery exist
[0xE]=0x1
[0x540]=0xA0
pl vm read [0x290]=0x50
pl vm set [0x290]=0x52
pl vm check [0x290]=0x52
pl pmic init done
[PLFM] Init I2C: OK(0)
[PLFM] Init PWRAP: OK(0)
[PLFM] Init PMIC: OK(0)
[PLFM] chip[CA00]
[I2C][PL] [i2c0 write] i2c transaction complate
[BLDR] Build Time: 20140218-141828
==== Dump RGU Reg ========
RGU MODE: 75
RGU LENGTH: FFE0
RGU STA: 40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 0
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
mtk_wdt_mode_config mode value=35, tmp:22000030
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
mtk_wdt_mode_config mode value=70, tmp:22000071
kpd register for pmic set!
mt_usb_calibraion: input_reg = 0x0
mt_usb_calibraion: term_vref = 0x0, clkref = 0x0, vrt_vref = 0x0,
[RTC] bbpu = 0x5, con = 0x426
[RTC] irqsta = 0x0, pdn1 = 0x0, pdn2 = 0x201, spar0 = 0x40, spar1 = 0x800
[RTC] new_spare0 = 0x0, new_spare1 = 0x1, new_spare2 = 0x1, new_spare3 = 0x1
[RTC] bbpu = 0x5, con = 0x424
SW reset with bypass power key flag
SW reset with bypass power key flag
[PLFM] WDT reboot bypass power key!
p1 pmic read INT_RSV(bit7)[0x138][0x80]
[RTC] rtc_bbpu_power_on done
[SD0] Bus Width: 1
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) DIV(193) DS(0) RS(0)
[SD0] Switch to High-Speed mode!
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) DIV(96) DS(0) RS(0)
[SD0] Bus Width: 8
[SD0] Size: 3696 MB, Max.Speed: 52000 kHz, blklen(512), nblks(7569408), ro(0)
[SD0] Initialized
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) DIV(0) DS(0) RS(0)
msdc_ett_offline_to_pl: size<2> m_id<0x90>
msdc <0> <HYNIX > <H4G1d>
msdc <1> <xxxxxx> <H4G1d>
msdc failed to find
*******EMMC_INFO*******
eMMC partition size(1 block = 512Bytes):
BOOT1:<4096> blocks
BOOT2:<4096> blocks
RPMB :<4096> blocks
GP1 :<0> blocks
GP2 :<0> blocks
GP3 :<0> blocks
GP4 :<0> blocks
USER :<7569408> blocks
*******EMMC_INFO*******
fw id len:1
found:1,i:1
[EMI] DDR2
[EMI] eMMC/NAND ID = 90,1,4A,48,34,47,31,64,4
[EMI] MDL number = 1
[MEM] 1066 MHZ
rank 0 coarse = 15
rank 0 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
rank 1 coarse = 15
rank 1 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,A)
byte:2, (DQS,DQ)=(8,8)
byte:3, (DQS,DQ)=(8,A)
[EMI] DRAMC calibration passed
[EMI] DQSINCTL:50000
[MEM] complex R/W mem test pass
[PLFM] Init Boot Device: OK(0)
[ROM_INFO] 'v2','0x2700000','0x20000','0x46C0000','0x2C00'
[SEC_K] SML KEY AC = 0
[SEC_K] SBC_PUBK Found
[SEC] AES Legacy : 0
[SEC] SECCFG AC : 1
[SEC] read '0x2700000'
0x41,0x4E,0x44,0x5F,0x53,0x45,0x43,0x43,
[LIB] SecLib.a '20121226-155014'
[LIB] CFG read size '0x4000' '0x1860'
[LIB] Name = SOMC
[LIB] Config = 0x11, 0x11
0x31,0x41,0x35,0x35
0x6F679858
[LIB] HW DEC
0x49494949
[LIB] SEC CFG 'v3' exists
[LIB] Status = 0x43434343
[LIB] ty = 0 , ld = 0
[PART] Image with part header
[PART] name : LK
[PART] addr : FFFFFFFFh
[PART] size : 316772
[PART] magic: 58881688h
[PART] load "UBOOT" from 0x0000000003960200 (dev) to 0x81E00000 (mem) [SUCCESS]
[PART] load speed: 9374KB/s, 316772 bytes, 33ms
[LIB] HW DEC
[SECRO] secroimg '0x41414141'
[SECRO] secroimg '0x35353535'
[SECRO] factory mode enabled
[AUTHEN] rsa.N length = 1024 bytes
[AUTHEN] rsa.E length = 20 bytes
[LIB] Verify 'UBOOT'
0x43434343
[LIB] part load '0x3960000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... pass
[LIB] Verify 'LOGO'
0x43434343
[LIB] part load '0x4D40000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... failed, error is 7
[SECLIB_IMG_VERIFY] Signature Fail.
[LIB] Fail (0x0)
<ASSERT> sec_boot.c:line 181 0
[PLFM] preloader fatal error...
[PLFM] emergency download mode(timeout: 30s).
mtk_arch_reset at pre-loader!
this is console with serial interface
i will post picture with pin layaut
how to unbrick?
botioni said:
[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=1 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=2 rdata=5AA5
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=3 rdata=5AA5
[PMIC_WRAP]wrap_init pass,the return value=0.
pl pmic init start
pl pmic efuse start
pl pmic efuse BUCK trim
[0x1C8]=0xF802
[0x1CA]=0x807F
[0x20E]=0xE0
[0x260]=0xF0
[0x286]=0xF0
pl pmic efuse end
pl pmic en rst [0x126]=0x13
[0xE]=0x1
[0x540]=0xA0
Battery exist
[0xE]=0x1
[0x540]=0xA0
pl vm read [0x290]=0x50
pl vm set [0x290]=0x52
pl vm check [0x290]=0x52
pl pmic init done
[PLFM] Init I2C: OK(0)
[PLFM] Init PWRAP: OK(0)
[PLFM] Init PMIC: OK(0)
[PLFM] chip[CA00]
[I2C][PL] [i2c0 write] i2c transaction complate
[BLDR] Build Time: 20140218-141828
==== Dump RGU Reg ========
RGU MODE: 75
RGU LENGTH: FFE0
RGU STA: 40000000
RGU INTERVAL: FFF
RGU SWSYSRST: 0
==== Dump RGU Reg End ====
RGU: g_rgu_satus:2
mtk_wdt_mode_config mode value=35, tmp:22000030
PL RGU RST: ??
SW reset with bypass power key flag
Find bypass powerkey flag
mtk_wdt_mode_config mode value=70, tmp:22000071
kpd register for pmic set!
mt_usb_calibraion: input_reg = 0x0
mt_usb_calibraion: term_vref = 0x0, clkref = 0x0, vrt_vref = 0x0,
[RTC] bbpu = 0x5, con = 0x426
[RTC] irqsta = 0x0, pdn1 = 0x0, pdn2 = 0x201, spar0 = 0x40, spar1 = 0x800
[RTC] new_spare0 = 0x0, new_spare1 = 0x1, new_spare2 = 0x1, new_spare3 = 0x1
[RTC] bbpu = 0x5, con = 0x424
SW reset with bypass power key flag
SW reset with bypass power key flag
[PLFM] WDT reboot bypass power key!
p1 pmic read INT_RSV(bit7)[0x138][0x80]
[RTC] rtc_bbpu_power_on done
[SD0] Bus Width: 1
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(0) DDR(0) DIV(193) DS(0) RS(0)
[SD0] Switch to High-Speed mode!
[SD0] SET_CLK(260kHz): SCLK(259kHz) MODE(2) DDR(1) DIV(96) DS(0) RS(0)
[SD0] Bus Width: 8
[SD0] Size: 3696 MB, Max.Speed: 52000 kHz, blklen(512), nblks(7569408), ro(0)
[SD0] Initialized
[SD0] SET_CLK(52000kHz): SCLK(50000kHz) MODE(2) DDR(1) DIV(0) DS(0) RS(0)
msdc_ett_offline_to_pl: size<2> m_id<0x90>
msdc <0> <HYNIX > <H4G1d>
msdc <1> <xxxxxx> <H4G1d>
msdc failed to find
*******EMMC_INFO*******
eMMC partition size(1 block = 512Bytes):
BOOT1:<4096> blocks
BOOT2:<4096> blocks
RPMB :<4096> blocks
GP1 :<0> blocks
GP2 :<0> blocks
GP3 :<0> blocks
GP4 :<0> blocks
USER :<7569408> blocks
*******EMMC_INFO*******
fw id len:1
found:1,i:1
[EMI] DDR2
[EMI] eMMC/NAND ID = 90,1,4A,48,34,47,31,64,4
[EMI] MDL number = 1
[MEM] 1066 MHZ
rank 0 coarse = 15
rank 0 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
rank 1 coarse = 15
rank 1 fine = 48
10:| 0 0 1 1 1 0
opt_dle value:8
byte:0, (DQS,DQ)=(8,8)
byte:1, (DQS,DQ)=(8,A)
byte:2, (DQS,DQ)=(8,8)
byte:3, (DQS,DQ)=(8,A)
[EMI] DRAMC calibration passed
[EMI] DQSINCTL:50000
[MEM] complex R/W mem test pass
[PLFM] Init Boot Device: OK(0)
[ROM_INFO] 'v2','0x2700000','0x20000','0x46C0000','0x2C00'
[SEC_K] SML KEY AC = 0
[SEC_K] SBC_PUBK Found
[SEC] AES Legacy : 0
[SEC] SECCFG AC : 1
[SEC] read '0x2700000'
0x41,0x4E,0x44,0x5F,0x53,0x45,0x43,0x43,
[LIB] SecLib.a '20121226-155014'
[LIB] CFG read size '0x4000' '0x1860'
[LIB] Name = SOMC
[LIB] Config = 0x11, 0x11
0x31,0x41,0x35,0x35
0x6F679858
[LIB] HW DEC
0x49494949
[LIB] SEC CFG 'v3' exists
[LIB] Status = 0x43434343
[LIB] ty = 0 , ld = 0
[PART] Image with part header
[PART] name : LK
[PART] addr : FFFFFFFFh
[PART] size : 316772
[PART] magic: 58881688h
[PART] load "UBOOT" from 0x0000000003960200 (dev) to 0x81E00000 (mem) [SUCCESS]
[PART] load speed: 9374KB/s, 316772 bytes, 33ms
[LIB] HW DEC
[SECRO] secroimg '0x41414141'
[SECRO] secroimg '0x35353535'
[SECRO] factory mode enabled
[AUTHEN] rsa.N length = 1024 bytes
[AUTHEN] rsa.E length = 20 bytes
[LIB] Verify 'UBOOT'
0x43434343
[LIB] part load '0x3960000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... pass
[LIB] Verify 'LOGO'
0x43434343
[LIB] part load '0x4D40000'
[AUTHEN] 0x53,0x53,0x53,0x53
[AUTHEN] verify signature ... failed, error is 7
[SECLIB_IMG_VERIFY] Signature Fail.
[LIB] Fail (0x0)
<ASSERT> sec_boot.c:line 181 0
[PLFM] preloader fatal error...
[PLFM] emergency download mode(timeout: 30s).
mtk_arch_reset at pre-loader!
this is console with serial interface
i will post picture with pin layaut
Click to expand...
Click to collapse
how did you check this out?
theonecallednick said:
how did you check this out?
Click to expand...
Click to collapse
I found uart pin on mainboard for debuging .
with serial usb cable pl2303
This is the red light only and unknown hardware found (the unknown hardware is in fact mtk usb vcom driver buth sony version ) if you try sp flash tool for mtk then it comunicates with de phone buth it needs some authentication file.
Help..
I am also having same problem..I falshed wrong rom..
It just shows red led and does not detects by PC...
Were you able to solve the problem..if yes..please help..
botioni said:
[PWRAP] pwrap_init_preloader
[PWRAP] pwrap_init
[PWRAP] _pwrap_init_sidly [Read Test] pass,SIDLY=0 rdata=5AA5
.........................
this is console with serial interface
i will post picture with pin layaut
Click to expand...
Click to collapse
Samuel Wankhede said:
I am also having same problem..I falshed wrong rom..
It just shows red led and does not detects by PC...
Were you able to solve the problem..if yes..please help..
Click to expand...
Click to collapse
Try the guide given in thread linked below
http://forum.xda-developers.com/showpost.php?p=57614511&postcount=13
Please share uart pinout
Baudrate should be 115200??
Thanks
uart
please share the uart pinout , thanks
Hello all ,
I linked a serial cable to my allwinner a20 based Android Tv box.
It can not pass after the boot logo and next is all what it display in serial console.
Somebody pelase help i need to reisntall linux on it ,if you knwo any u boot keys that i have to press on the uboot serial consoel pelase help.I tryed to press ransom keys but i see nothin.
Here is all i see when it start:
====================================
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =512
sum=0x9c3bd8cf
src_sum=0x9c3bd8cf
Ready to disable icache.
Jump to secend Boot.
[ 0.133]
U-Boot 2011.09-rc1-dirty (Nov 08 2013 - 11:06:32) Allwinner Technology
[ 0.141]version: 1.1.0
[ 0.144]pmbus: ready
axp read error
probe axp20x failed
axp_probe error
boot_clock = 912
dcdc2_vol = 1400
axp set dcdc2_vol to 1400 failed
dcdc3_vol = 1250
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 0
storage_type = -1
usb_recovery = 0
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[ 0.293]DRAM: 512 MiB
relocation Offset is: 15b27000
user_gpio config
user_gpio ok
DRV_DISP_Init: opened
[ 0.560]boot_disp.output_type=2
[ 0.563]boot_disp.output_mode=5
[ 0.567]boot_disp.auto_hpd=1
workmode = 0
[ 1.871]NAND: NAND_UbootInit
NB1 : enter NAND_LogicInit
nand : get id_number_ctl from script, 3
not burn nand partition table!
NB1 : nftl num: 3
init nftl: 0
NB1 : NAND_LogicInit ok, result = 0x0
[ 2.381]sunxi flash init ok
In: serial
Out: serial
Err: serial
--------fastboot partitions--------
-total partitions:12-
-name- -start- -size-
bootloader : 1000000 1000000
env : 2000000 1000000
boot : 3000000 1000000
system : 4000000 20000000
recovery : 24000000 2000000
databk : 26000000 2000000
misc : 28000000 1000000
private : 29000000 1000000
sysrecovery : 2a000000 21000000
data : 4b000000 40000000
cache : 8b000000 17000000
UDISK : a2000000 0
-----------------------------------
base bootcmd=run setargs_nand boot_normal
bootcmd set setargs_nand
key 0
recovery key high 6, low 4
cant find fstbt value
Fastboot detected, will boot fastboot
to be run cmd=run setargs_nand boot_fastboot
the user data'magic is bad
WORK_MODE_BOOT
board_status_probe
sunxi_bmp_display
WORK_MODE_BOOT
[ 2.509]Hit any key to stop autoboot: 0
run usb fastboot
sunxi_fastboot_init
recv addr 0x41000000
send addr 0x582580a8
delay time 0
usb init ok
------------------------------------------------------------------
After this nothing .Please help me
After searching all google and reading documantation ,I contacted the box seller and he gied me the files i neeeded.
I used a image file named sun7i_A20v2.0_android_sugar-ref001_2014.09.04_TakenYBSJ.img and a windwos software to flash it via usb named PhoenixPacketV333
To flash teh device you muist hava a serial console to the box (veru easy to do if you have the cable ) ,and keep pushed the key 2
on serial consle (putty) while powering the device ,so it enter in fel mode ( something like recovery mode ,it accept usb connection) .Then oyu need a usb male to male cable to conect the android tv box usb port to the windows usb port ,and start flasing using the PhoenixPacketV333 software.
If somebody needs more help or files just write here I check daily .
have a nice day all!
What could be the problem ..
Operation : Identify [ v2.18 ]
Mode : FLASH
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port (COM7)
MODE : BOOTROM
PORT : 7
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : MEID : 84E1311723E5F72DDF767B7B831BD757
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2044 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_SP.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 45000170414934456E0101344F2524D7
DAInf: 4 : 2 : 156
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 70010045453449413401016ED724254F
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
DRAM : 0x0178
EMI : DEV : MT6752
EMI : SRC : preloader_k80hd_bsp_fwv_512m.bin
EMI : CNT : 0003
EMI : [00] : ID : 700100454534454134 : VEN : KINGSTON | DEV : EE4EA4 : RAM : [ 512.00 MB ]
EMI : [01] : ID : C80111344D45594D41 : VEN : UNKNOWN | DEV : 4MEYMA : RAM : [ 512.00 MB ]
EMI : [02] : ID : 700100454534494134 : VEN : KINGSTON | DEV : EE4IA4 : RAM : [ 512.00 MB ]
EMI : Init EMI from PRELOADER
INIT : 0xBC : DRAM [ 0x00000000 : [ 0 B ] ]
DRAM : DRAM: 0x20000000 [ 512.00 MB ]
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info
EMMC: 70010045453449413401016ED724254F
EMMC: VEN : KINGSTON | OEM : 01 | DEV : EE4IA4
EMMC:
BOOT1 : 0x00200000 [ 2.00 MB ]
BOOT2 : 0x00200000 [ 2.00 MB ]
RPMB : 0x00080000 [ 512.00 KB ]
USER : 0xE2000000 [ 3.53 GB ]
SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0x20000000 [ 512.00 MB ]
CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000
RNID : C936D9FF3A84D90E7B2010FA5212EA26
STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT
DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM9)
MODE : PRELOADER PORT
PORT : 9
Boot done!
Patch Level : O11019
Display ID : O11019 release-keys
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2019-09-05
Build Time : 23.08.2019
Product Model : Kicka_4_Plus
Product Brand : MobiWire
Product Name : Kicka_4_Plus
Product Device : Kicka_4_Plus
Product Manfct : MobiWire
Product Info : k80hd_bsp_fwv_512m
Board Platform : mt6580
Product Board : VP402_Mobiwire_Kicka4Plus
USERDATA : FILESYSTEM : F2FS with FDE ( Full Disk Encryption ***)
Done!
Elapsed: 00:00:30
Operation : HW Test [ v1.58 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 1 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6580
BB_CPU_NME : [MediaTek] MT6580_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v3.3001.2018-04-25.11:26_437806
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x9C
NAND Flash : NOT INSTALLED
eMMC Flash : 70010045453449413401016ED724254F
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x70 , OEM : 0100
[eMMC] : FLASH_INF : [KINGSTON] , 4AI4E
[eMMC] : FLASH_CID : 70010045453449413401016ED724254F
[eMMC] : FLASH_BRT : 0x00200000 , 0x00200000 , 0x00080000
[eMMC] : FLASH_LEN : 0x00000000E2000000
[eMMC] : FLASH_UCP : 3616 MiB [eMMC 4 GiB]
DEV RID : 0x4EA014B2FFD936C90ED9843AFA10207B
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
Processing Miscellaneous test
MSC : BatteryLevel : 3009 mV
[Processing] FlashMemory Read-Write test
[eMMC] : [KINGSTON] , 4AI4E , 0xE2000000 , 3616 MiB
[eMMC] : CID : 70010045453449413401016ED724254F
[eMMC] : MODE : SQ-WR
[PASSED] : eMMC RW Check #1 Ok!
[eMMC] : MODE : RA-WR
[PASSED] : eMMC RW Check #2 Ok!
[eMMC RO CHECK] : eMMC Ok! READ-WRITE Passed!
[Processing] RAM Read-Write test
[DRAM] : 0x20000000 , 512 MiB
[DRAM] : ADDRESS BUS test
[PASSED] : Bus Count : 0x1C
[DRAM] : DATA BUS test
[PASSED] : Bus Count : 0x1F
[DRAM] : PATTERN test
[PASSED] : PATTERN Ok
[DRAM] : INCDEC test
[PASSED] : INCDEC Ok
All Done!
Done!
Elapsed: 00:01:40
Reconnect Power/Cable!