What the heck is the difference between THIS (a regular HD Screen Protector) and THIS (a tempered glass screen protector)
Reg screen protectors are just thin pieces of film that don't do much protecting against drops, but will prevent minor scratches. Temp glass usually has a hardness of h9 and will save your screen if it takes a bad spill, I know of this first hand. Hopefully the temp glass will cracked leaving your phones screen intact. Temp glass is just better protection all around AND it will prevent your screen from becoming part of the recycling trash on friday. Temp glass has saved me twice, one with a note 4 and once with an LG g3. I would never go back to buying those thin film protectors that do nothing
I don't have first-hand experience with tempered glass protectors, but I do think standard screen protectors offer more protection than twoeleven99 indicated. I used a Skinomi front and back protector on my Nexus 4 (also a glass sandwich), and it adds a nice barrier to the glass. It also has some give, so it absorbs some of the impacts that would otherwise shatter glass.
Another thing I liked is that it adds slightly more grip than glass, preventing drops and slips. It would also be way more practical for the S6 edge, since the wet-apply ones can handle curved screens no problem.
That said, I'm going to give a tempered glass one a shot this time to see if it is more clear (eg: less rainbowing or orange peel effect).
As mentioned already, a tempered glass screen protector will do a better job protecting your phone's screen from damage. They may cost more initially, but they'll last a while. You typically have to change out plastic screen protectors more frequently after light scratches have built up.
Sent from my iP6+
I've been using tempered glass screen protectors for the last 2 years. They add thickness, but they're honestly amazing. One thing that I've never really confirmed, but I keep hearing rumors that when dropping a device with a tempered glass screen protector, the energy disperses onto the protector, therefore shattering the protector rather than the phone's screen itself. I never really had a massive drop before to test this out (nor do I have the funds to break my phones), but I have dropped my G2 before, and the corner of the protector cracked while the screen itself was completely fine.
I also like how glass feels compared to PET screen protectors.
asdfvtn said:
I've been using tempered glass screen protectors for the last 2 years. They add thickness, but they're honestly amazing. One thing that I've never really confirmed, but I keep hearing rumors that when dropping a device with a tempered glass screen protector, the energy disperses onto the protector, therefore shattering the protector rather than the phone's screen itself. I never really had a massive drop before to test this out (nor do I have the funds to break my phones), but I have dropped my G2 before, and the corner of the protector cracked while the screen itself was completely fine.
I also like how glass feels compared to PET screen protectors.
Click to expand...
Click to collapse
I've had the tempered glass completely shatter from one end to the other on 2 devices. Peeled it off and the screen under never had a scratch on it
I've tried a couple of tempered glass screen protectors so far (supershieldz and dmax) and both of them leave a few mm glass on all sides. This couples with the ringke case leaves a gap for dust to collect.
I was wondering this this phone has a flat screen, not curved at the edges, would there be a way to get a screen protector that completely covers it right to the edge or with a very small gap(<1mm).
Does anyone know of a glass protector like that which will cover 100% of the front face?
Thanks
@intelliARMOR have said they are making one in the next month once they get their first batch of more case friendly screens out.
I just received my IMAK glass screen protector. Purchased this on AliExpress. Here are some photos of it and how I installed it. I used the 3 stickers to make a hinge after it's positioned correctly. That way I just have to remove the backing and then stick it. I'll just seperate my review into pros and cons.
Pros:
-The screen protector fits nicely. I chose this one because it has the little speaker cut out on top.
-It feels good because it is glass.
-It protects the screen well because it is glass.
Cons:
-It is glass so it has some thickness to it.
-Holds fingerprints more than screen itself
-It has a little orange peel so it's not crystal clear. You can see in the picture of the reflection of the light that it looks a little muddy instead of mirror like.
Overall, it's good for the price, but not perfect. Personally I'm back and forth between glass and film screen protectors. I'll give this a try for a few weeks and then make a final decision.
https://flic.kr/p/YVQY5o https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/YiqUeK https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/YiqRJz https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/ZgR8h3 https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/Zfqq6y https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/ZfqmJd https://www.flickr.com/photos/[email protected]/
https://flic.kr/p/YVQPHJ https://www.flickr.com/photos/[email protected]/
Those guiding stickers are ingenious, never seen them before and the idea is just so simple and clever!!
Perfect, I know what I have to do when my phone and Nillkin protector arrive.
Thanks for sharing.
That is a lot nicer than the Riffue Tempered Glass screen protector I bought on Amazon. This one is thin and has a good height but is several mm too narrow, it doesn't even cover the LCD display let alone the entire screen/glass.
the one i order covers like half of the screen lmao wtf
just ordered one like yours.
I had one similar too this, but the dust collected over front camera under the glass.
It has some glue on it, does this IMAK one used static?
Here is a link to the one i bought.
I tried many different ones but for me this is the best.
The coating is very good against fingerprints. It fits perfect on the screen.
The sides of the screen are a little bit curved down which is good for the dust.
Updated link https://www.aliexpress.com/item/Ima...lgo_pvid=6f18e507-ed27-486a-869e-418c35f3a452
dewingerd said:
Here is a link to the one i bought.
I tried many different ones but for me this is the best.
The coating is very good against fingerprints. It fits perfect on the screen.
The sides of the screen are a little bit curved down which is good for the dust.
https://www.aliexpress.com/snapshot/0.html?spm=a2g0s.9042647.0.0.JDCsAY&orderId=87369620878335&productId=32835736602
Click to expand...
Click to collapse
The link you've sent is private, I think we can't view it.
kurtextrem said:
The link you've sent is private, I think we can't view it.
Click to expand...
Click to collapse
Try this one : https://www.aliexpress.com/item/Ima...lgo_pvid=6f18e507-ed27-486a-869e-418c35f3a452
Do it sticks in all the area? or only in borders?
Thanks
DeividMS said:
Do it sticks in all the area? or only in borders?
Thanks
Click to expand...
Click to collapse
All the area.
Got the IMAK today and it is on and I LOVE it!!
Like there is no screenprotector there at all.
Will purchase some more rightaway.
EDIT: Never seen something fit so well!!
Dust2Dust said:
Got the IMAK today and it is on and I LOVE it!!
Like there is no screenprotector there at all.
Will purchase some more rightaway.
EDIT: Never seen something fit so well!!
Click to expand...
Click to collapse
I agree, this is the best screenprotector i have ever bought. It fits perfect and the coating feels the same as on the original screen :good::good:
Just wanted to echo everyone else about how great the Imak full coverage screen protector is. I went through four different screen protectors so far (unknown brand thin plastic one, MOFI tempered glass, another MOFI tempered glass, and finally the IMAK full coverage)
The thin plastic one came bundled with the phone and would scratch if you so much as raised your voice at it. Placed it on just as a temporary protector while waiting for the others to come from Aliexpress. It just barely covered the display and left about 1.5mm of space on the edges. The phone was accidentally smacked out of my hand once and landed on a sandy floor face down, which I later discovered upon removal of the screen protector had caused a small chip on the screen near the edge, so the protector might have absorbed some of the impact.
The first MOFI tempered glass I got was a "full coverage" one, but it arrived with notches cut out on the bottom where the proximity sensor and front camera are. The worst thing about this one was that it only had adhesive on the edges, so there was a really distracting and noticeable rainbow effect (newton rings) in the middle of the screen.
The second MOFI tempered glass was also full coverage, and this time it didn't have notches at the bottom, just a hole cutout where the proximity sensor is located. The adhesive type was the same as the previous one, edge only, resulting in the newton ring effect. It also mysteriously cracked for no reason.
The one I have on currently is the IMAK full coverage screen protector. Indisputably the best out of all of them, the protector fits exactly over the entire front glass, and instead of cutout holes at the bottom, the chin at the bottom is fully glass, blackened except for where the proximity sensor and front camera are. Full adhesive all throughout means there is no rainbow effect, and the LED notification light is even tinted slightly so that it blends in with the chin, and is invisible until it turns on! The only flaw about this screen protector (yes, there is one) is that the area underneath the front camera is too thin to apply adhesive, so as a result there's a tiny gap between the glass and phone that can let in dust after a while. The dust does not seem to affect the front camera, and I never take selfies anyway, but I have yet to figure out a good way to get the dust out of there.
I have never had a screen protector fit this perfectly, even for phones other than the Mi Mix 2. Most other screen protectors have cutouts for the proximity sensor/front camera/both, but this one blends in so well that it feels like it's not even there.
Does anyone know if this protector has a dot matrix on the screen (tiny dots that reflect)? I purchased a Misha 3D protector from Amazon which looks identical to this, and it's great except for the grid of dots across the screen.
dodgyc said:
Does anyone know if this protector has a dot matrix on the screen (tiny dots that reflect)? I purchased a Misha 3D protector from Amazon which looks identical to this, and it's great except for the grid of dots across the screen.
Click to expand...
Click to collapse
When I tried it there were no dots, just very reflective and had a weird smudge pattern going on which ruined it.
The flossmall one posted elsewhere is so much better.
Lol those kind of screen protectors damn sucks, they are not full glue, so that make lot of reflections. The nillkin (regular tempered glass, full glue, no black borders), is perfect and cover all the display... So why buy this imak piece of ****?
Zedramus said:
Just wanted to echo everyone else about how great the Imak full coverage screen protector is. I went through four different screen protectors so far (unknown brand thin plastic one, MOFI tempered glass, another MOFI tempered glass, and finally the IMAK full coverage)
The thin plastic one came bundled with the phone and would scratch if you so much as raised your voice at it. Placed it on just as a temporary protector while waiting for the others to come from Aliexpress. It just barely covered the display and left about 1.5mm of space on the edges. The phone was accidentally smacked out of my hand once and landed on a sandy floor face down, which I later discovered upon removal of the screen protector had caused a small chip on the screen near the edge, so the protector might have absorbed some of the impact.
The first MOFI tempered glass I got was a "full coverage" one, but it arrived with notches cut out on the bottom where the proximity sensor and front camera are. The worst thing about this one was that it only had adhesive on the edges, so there was a really distracting and noticeable rainbow effect (newton rings) in the middle of the screen.
The second MOFI tempered glass was also full coverage, and this time it didn't have notches at the bottom, just a hole cutout where the proximity sensor is located. The adhesive type was the same as the previous one, edge only, resulting in the newton ring effect. It also mysteriously cracked for no reason.
The one I have on currently is the IMAK full coverage screen protector. Indisputably the best out of all of them, the protector fits exactly over the entire front glass, and instead of cutout holes at the bottom, the chin at the bottom is fully glass, blackened except for where the proximity sensor and front camera are. Full adhesive all throughout means there is no rainbow effect, and the LED notification light is even tinted slightly so that it blends in with the chin, and is invisible until it turns on! The only flaw about this screen protector (yes, there is one) is that the area underneath the front camera is too thin to apply adhesive, so as a result there's a tiny gap between the glass and phone that can let in dust after a while. The dust does not seem to affect the front camera, and I never take selfies anyway, but I have yet to figure out a good way to get the dust out of there.
I have never had a screen protector fit this perfectly, even for phones other than the Mi Mix 2. Most other screen protectors have cutouts for the proximity sensor/front camera/both, but this one blends in so well that it feels like it's not even there.
Click to expand...
Click to collapse
After putting the screen protector on, I take a toothpick and put some glue from a Pritt-stick in the little gap underneath the camera. Not much, just enough to close the gap. When it has dried you can color it with a black whiteboard marker if you want. When you remove the screen protector you can easily rub it off. Works great for me :good:
Thanks!
Anyone tried these?
https://www.aliexpress.com/store/pr...Front-2PCS-Back-Soft/1879465_32831400367.html
Looking to buy this phone, any new news on protectors, or is IMAK our best option?
Thanks
I see this one on Amazon from Mocolo and it looks like it does? But its shipped from China...
Most of the glass screen protectors leave about 1-2mm of space from the screen to the edge but it's due to the rounded edges on the screen. Another issue that has been ongoing is that the glass screen protectors are not sitting well and there is a "Halo" effect around the edges of the screen on the screen protector.
So far the Skinomi, Phantom Skins style screen protectors sit the best but some have had minor issues with cases.
I just ordered the Mocolo screen protectors yesterday and I'm hoping they don't give the Halo effect.
Ghost_1 said:
Most of the glass screen protectors leave about 1-2mm of space from the screen to the edge but it's due to the rounded edges on the screen. Another issue that has been ongoing is that the glass screen protectors are not sitting well and there is a "Halo" effect around the edges of the screen on the screen protector.
So far the Skinomi, Phantom Skins style screen protectors sit the best but some have had minor issues with cases.
I just ordered the Mocolo screen protectors yesterday and I'm hoping they don't give the Halo effect.
Click to expand...
Click to collapse
"Halo effect" means not cut short enough.
tech_head said:
"Halo effect" means not cut short enough.
Click to expand...
Click to collapse
Sort of, the halo effect can be related to the screen protector not being cut short enough (or too long) where the screen bevel begins and the adhesive does not adhere to the outside edges of the screen protector.
And/Or
The adhesive does not adhere to the outside edges of the screen protector causing an unsightly "halo effect" where there is a unsightly discoloration/visual issue.
It is easy enough to see on the multiple threads and or can be Google searched for more pictures or a better idea of what it looks like.
Ghost_1 said:
Most of the glass screen protectors leave about 1-2mm of space from the screen to the edge but it's due to the rounded edges on the screen. Another issue that has been ongoing is that the glass screen protectors are not sitting well and there is a "Halo" effect around the edges of the screen on the screen protector.
So far the Skinomi, Phantom Skins style screen protectors sit the best but some have had minor issues with cases.
I just ordered the Mocolo screen protectors yesterday and I'm hoping they don't give the Halo effect.
Click to expand...
Click to collapse
will be interested in how that Mocolo works out
Check out "Brotect" protectors. They do tempered glass, "air glass" and normal plastic ones, all clipped short of the curve and therefore case friendly.
Used one if their protectors on a previous phone and seemed fine. I have the airglass one for the ph-1 here but not fitted it yet
Skinomi just released one. I have their full coverage one and it is fantastic.
Update: forget about the Mocolo TGSP, it's cut too short on the sides. So much so I didn't even bother putting it on. I'm sure there won't be a Halo but it leaves about .5mm on either side when I did a test fit.
I've now purchased the lightning knight, Orzero 3rd gen (I think, this is the one with full adhesive but rounded black border, and Mocolo TGSP. Fitment wise the lightning knight (LK) fits the best but has Halo. The Orzero is wider than the LK but from what I've seen in the reviews the Halo is horrible. I'd also assume that it would be bad as the Orzero goes to where the screen starts to round at the edge, also it might be an issue with cases.
You can see the Mocolo on Amazon and the fitment issues in the purchaser gallery.
I have the mocolo in clear (not black) and unfortunately halo effect is pretty bad, just like the rest. Quite ugly so ripped it off and currently going without anything.
I gave up.
I'm going to use the approach of others with a liquid UV adhesive and a screen protector with no glue.
I've bought a few from Xtreme guard and they fit perfectly with any case!! Plus you can get em dirt cheap by searching for promo codes. Got mine for .99 each!!!
This suggestion might not be a solution for everyone but life is a series of compromises I guess. I've bought half a dozen glass screen protectors(all the ones available on amazon) and several phone cases as I was unwilling to go without a full glass protector on my phone so this is the solution i came up with. Confirmed repeatable, I'm preforming this on my 3rd PH-1(pictures) while i write this. (don't worry, its not because they broke!)
So basically:
Orzero 9H glass screen protector + Poetic Guardian Case
https://www.amazon.com/Orzero-Essential-Tempered-Protector-Replacement/dp/B077XT5V7Z/ref=sr_1_1?ie=UTF8&qid=1539386003&sr=8-1&keywords=essential+orzero
https://www.amazon.com/Essential-Poetic-Resistant-Protection-Full-Body/dp/B078T3N1S7/ref=sr_1_1?ie=UTF8&qid=1539386315&sr=8-1&keywords=essential+poetic
The glass protector itself is the best of all the glass protectors i've tried so far but it still has its shortcomings. The glue is applied to the black thin line around the border which is ok on the bottom but the top is too thin. Once installed it "floats" around up top near the camera. NOTE: Eventually the glass gets the spotted rainbow effect in the glass center. Not noticeable once the screens on but some i know would like to know this before hand. Slick glass feel tho, no more finger printy then the factory glass. With a hard press you can move it around and recenter it but im sure eventually it will fall off left alone.
That is where the case comes in. The case is two piece, the bumper that is raised around the screen(inner case), overlaps and has a plastic cheapy protector glued in place.
Clean and apply the glass protector. Clean the edges of the glass protector and ensure its centered. Take the inner case and remove the cheap plastic protector that it comes with. LEAVE THE GLUE on the inner case. Install the inner case over the phone ensuring the protector is centered once again before pressing down around the edges firmly. Install remaining outer case rubber.
You now have an Essential phone WITH A GLASS SCREEN PROTECTOR!! The case is IMO not the prettiest but feels great, easy to grab and grip, cutouts and port covers all work properly, buttons are still clicky. My wife even likes it more then her retired iPhone, and that's saying something
Remember to press against the glass protector at the bottom mainly, if you need to remove the inner case so it does not lift.
Hope this helps those PH-1 owners who wish to enjoy the security of a glass screen protectors. :highfive:
Poetic's glass screen protector also works with the Tudia Glost case. I think that was posted in the cases thread some time ago. That's the combination I'm using now. So far the Poetic screen protector has stayed on very well. It has the same rainbow issue when the screen is off, but like you said, you can't see it when the screen is on.
Ya, i avoided that case since lots of reviews about the back cracking upon dropping it. Haven't seen the peotic brand glass protectors either but im sure this works with any protector and case with similar designs