This suggestion might not be a solution for everyone but life is a series of compromises I guess. I've bought half a dozen glass screen protectors(all the ones available on amazon) and several phone cases as I was unwilling to go without a full glass protector on my phone so this is the solution i came up with. Confirmed repeatable, I'm preforming this on my 3rd PH-1(pictures) while i write this. (don't worry, its not because they broke!)
So basically:
Orzero 9H glass screen protector + Poetic Guardian Case
https://www.amazon.com/Orzero-Essential-Tempered-Protector-Replacement/dp/B077XT5V7Z/ref=sr_1_1?ie=UTF8&qid=1539386003&sr=8-1&keywords=essential+orzero
https://www.amazon.com/Essential-Poetic-Resistant-Protection-Full-Body/dp/B078T3N1S7/ref=sr_1_1?ie=UTF8&qid=1539386315&sr=8-1&keywords=essential+poetic
The glass protector itself is the best of all the glass protectors i've tried so far but it still has its shortcomings. The glue is applied to the black thin line around the border which is ok on the bottom but the top is too thin. Once installed it "floats" around up top near the camera. NOTE: Eventually the glass gets the spotted rainbow effect in the glass center. Not noticeable once the screens on but some i know would like to know this before hand. Slick glass feel tho, no more finger printy then the factory glass. With a hard press you can move it around and recenter it but im sure eventually it will fall off left alone.
That is where the case comes in. The case is two piece, the bumper that is raised around the screen(inner case), overlaps and has a plastic cheapy protector glued in place.
Clean and apply the glass protector. Clean the edges of the glass protector and ensure its centered. Take the inner case and remove the cheap plastic protector that it comes with. LEAVE THE GLUE on the inner case. Install the inner case over the phone ensuring the protector is centered once again before pressing down around the edges firmly. Install remaining outer case rubber.
You now have an Essential phone WITH A GLASS SCREEN PROTECTOR!! The case is IMO not the prettiest but feels great, easy to grab and grip, cutouts and port covers all work properly, buttons are still clicky. My wife even likes it more then her retired iPhone, and that's saying something
Remember to press against the glass protector at the bottom mainly, if you need to remove the inner case so it does not lift.
Hope this helps those PH-1 owners who wish to enjoy the security of a glass screen protectors. :highfive:
Poetic's glass screen protector also works with the Tudia Glost case. I think that was posted in the cases thread some time ago. That's the combination I'm using now. So far the Poetic screen protector has stayed on very well. It has the same rainbow issue when the screen is off, but like you said, you can't see it when the screen is on.
Ya, i avoided that case since lots of reviews about the back cracking upon dropping it. Haven't seen the peotic brand glass protectors either but im sure this works with any protector and case with similar designs
Related
Anybody use one of the tempered glass protectors with TPU cases, or other cases you have to pop on and off? When I tried to use PET screen protectors with my Diztronic case, it just peeled up the corners and ruined the protector.
I'd like to put a tempered glass protector on, but the Diztronic has to come off regularly to remove dust. Will it cause fit problems or peel away/fracture the glass when I try to put the case back on? Suggestions in general for protection without getting some kinda bulky Commuter case are welcome as well. I feel like some kind of case is pretty necessary, as opposed to a skin, because I use my phone in a lot of gritty, dirty places, and while I don't drop it often, if it does go down, it's typically onto concrete. It's survived the past two years pretty much unscathed, but I want to keep it as my daily driver for at least a few more months.
royalewihcheese said:
Anybody use one of the tempered glass protectors with TPU cases, or other cases you have to pop on and off? When I tried to use PET screen protectors with my Diztronic case, it just peeled up the corners and ruined the protector.
I'd like to put a tempered glass protector on, but the Diztronic has to come off regularly to remove dust. Will it cause fit problems or peel away/fracture the glass when I try to put the case back on? Suggestions in general for protection without getting some kinda bulky Commuter case are welcome as well. I feel like some kind of case is pretty necessary, as opposed to a skin, because I use my phone in a lot of gritty, dirty places, and while I don't drop it often, if it does go down, it's typically onto concrete. It's survived the past two years pretty much unscathed, but I want to keep it as my daily driver for at least a few more months.
Click to expand...
Click to collapse
TGSPs are typically smaller than plastic film ones, to ensure that they'll work with cases. I have the Redpepper TGSP on my Nexus 4, and it fits with all my cases, including a Diztronic.
I'm having Distronic TPU case and glass screen protector on my mom's N4, as there is a curve on the front panel the screen protectors would usually be even smaller than the actual screen.
And I'm having totally no problem with the screen protector and the case, except the uncovered thickness of the glass screen protector makes it relatively more noticeable than a plastic one.
I received my amFilm tempered glass screen protector 3 days ago. The packaging of all the contents came in a hard clear plastic which included:
Tempered glass screen protector
Rear PET screen protector
An alcohol wipe
A dry wipe
6 dust removing stickers
Micro-fiber cloth
Squeegee card
Instructions
Following the instructions, of course I washed my hands to remove any oils/dirt. Tip- I would suggest doing this in an area as clean as possible. TIP: states do it in the bathroom after a hot shower has been running so the steam settles any dust. I've done this on Zagg screen protectors and it works, but I failed to do this which caused troubles during installation.
I powered down the phone and wiped the screen with the included alcohol wipe. Then using the dry wipe i wiped off any excess liquid (which was not very much). I used the micro-fiber cloth to wipe the screen down one more time. Looking a the screen i saw one strand of fiber/dust, which then I used the stickers included which lifted it right off.
Installing the tempered protector was fairly straight forward. I tried to center the screen protector and used the home button to gauge how off center to the left and right I was and if the glass was angled in relation to the top of the home button. I made sure the glass was straight along both sides of the screen and placed it down. You do need to press in the center vertically and horizontally for the glass to set well.
Lifting the glass up was pretty easy using a finger nail, I had to lift it off because debris got under and got attached to the tempered glass. I used the dust sticker again and it removed the debris with ease. Positioning the tempered glass again I got it this time. For some reason the edges of the tempered glass still have this look that the sticky backing isnt completely pressed down. I try for 30sec-1min to hold my thumb on these areas and it comes back. That look when an air bubble is under and it wont get pressed out is the best I can describe.
I'm a perfectionist, this probably caused installing it harder than it should have been.
Yes there is a gap about 3 credit cards thick between top and bottom. I do wish it covered more toward the bottom and under the home button and reaching up between the front camera and earpiece grill.
There is also a gap of about 2 credits from the sides of the tempered glass and my Spigen Hybrid Crystal case. I understand why they did this because different cases grip around the front of the phone differently, so to be compatible the width of the tempered glass is just wide enough to cover the actual screen.
Just wish the tempered glass covered a little more.
The thickness of the amFilm tempered glass is .33mm. This makes the glass just a tad higher than the home button, which makes it nice as its more comfortable when my thumb may be at the bottom and it feels more flush than having the home button raised.
Another thing i notice is the softkeys at the bottom emit a glow just below the tempered glass ends. This annoys me because I feel the glass wasnt properly measured.
The glass is very smooth and attracts less finger prints than without it or on my bare LG G2 screen (having no screen protector).
After 3 days of use, there still are those areas around the screen that will not go away (See photo below). At the moment that is the only thing bothering me. It feels nice and visibility is perfectly clear, touch response has gone unchanged as well.
For the price of $7.99 + free shipping (at the time of me writing this) on Amazon http://www.amazon.com/gp/product/B00UH8KKA0/ref=cfb_at_prodpg
its not bad and for that price can't go wrong with it. It comes with a rear PET screen protector, which I did not install. So there is extra benefit :good: (I have plans to install a dBrand rear skin).
Feel free to ask any questions.
Here are some pictures of everything described.
I took your advice and ordered one. Thanks for taking the time to review this screen protector. I appreciate it. I'll get it in a couple days. I'm sure it will do just fine. It seems from your description that installing it is simple enough. Thanks again.
I have this. It cracks if you just drop the phone onto a hard surface from like 1 or 2 inches high. Very fragile... They replaced first one for free. I don't know if they will replace the second one. But, I'm happy it's there to take the impact in stead of the real screen..
There are glass sp 0.2-0.25mm thickness for less than $5 on ebay. They work just as well, if not better.
I'm at my wits end from breaking my screen for the fourth time. 3 of those time were with the invisible shield screen protector. The only thing that protector can protect my screen from is little scratches or nicks. Other than that? I say no way. What do you guys use as a better screen protector from a drop on the face. Because it doesn't take much for these screens to break. I mean, even the older phone's screen were tougher than these. I really wish there were otter boxes for the nexus.
marioc89 said:
I'm at my wits end from breaking my screen for the fourth time. 3 of those time were with the invisible shield screen protector. The only thing that protector can protect my screen from is little scratches or nicks. Other than that? I say no way. What do you guys use as a better screen protector from a drop on the face. Because it doesn't take much for these screens to break. I mean, even the older phone's screen were tougher than these. I really wish there were otter boxes for the nexus.
Click to expand...
Click to collapse
I've got a 2.5D tempered glass screen protector on mine. A plastic film screen protector won't protect it from shattering from a fall, but a TGSP might, depending on how it lands. Of course, any drop on a corner, and the screen will break, which is why I keep mine in a case. Do you not keep it in a case? I use a Diztronic TPU, and never felt like it's under-protected.
Yes. I have it in a case but it's really not the best. I've just learned of ballistic cases that are really good. But I would like a tempered glass for extra protection. One that doesn't cover the camera or sensors on front.
I personally use a KWmobile film protector (cheap, does its job and it's pretty matte so not many reflections on the screen), and right now I am at my second flip cover. The first one got DESTROYED after taking all of the drops instead of the phone
But it's all about taste, I personally like flip covers as they make me look more professional
where get tempered glass protector from? all ones iv seen don't curve with the screen properly
I would recommend using skinzone's screen protector, high quality and protects good
After having seen all of the issues with the glass screen protectors for this phone, I decided that I needed to try something else in the meantime. While I have a Sakai glass one that I ordered from ebay that is due roughly a month from now, I'm not very hopeful for it working. As a result of all of this and the need for a screen protector ASAP, I went with the Spigen screen protectors that I have seen mentioned on here. Having used PET films in the past, I was expecting a huge hassle. Bubbles, cheap feeling etc. Turns out, these worked REALLY damn well, to my complete surprise.
Installation:
Installation was quite easy, much easier than the older thin film screen protectors that I remember. You simply clean the surface of the phone, following the instructions. Place the tabs on the screen protector to help you position it. Then carefully position it properly keeping an eye on the edges and the sensors. It adheres to the screen very much like a glass screen protector does. There are a few small bubbles here and there, but they squeegee right out. I ended up with two permanent bubbles (one by the light sensor and one near the edge). Neither were the fault of the screen protector, both were caused by me rushing and nicking the surface of the screen protector when squeegee-ing the bubbles out. I think I could easily get it on there next time with zero bubbles. Way less hassle than any other attempt I have had with a film screen protector. One complaint I have is that they only included one alcohol wipe (everything else is in multiples), I don't know if I just got unlucky or they aren't thinking. Anyways, I have access to many solvents at work. No big deal for me.
Result:
How does it feel? A bit more plasticy than the usual glass screen protector but otherwise surprisingly nice. It adheres to the curves perfectly with no major bubbles, clarity-wise it is crystal clear. I honestly can't tell it is there. It adheres nicely to the curves of the display without any gaps (other than my nicks at the edge). My Otterbox Commuter case fits right over the top of it with ZERO problems. I was expecting these to be a stop-gap measure until the better glass ones come out but honestly I don't see anything wrong with these as is and would be just fine using these alone. I am not sure about longevity as I just installed it but so far I am actually surprisingly happy with it, especially for the cost. If you are on the fence between glass and plastic. Go with these plastic screen protectors for now and let the manufacturers work out the difficulties of the glass ones. Then you can decide later if you really want the glass one for you phone.
Link:
https://www.amazon.com/gp/product/B01B1GQDGG/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
it will get scratched to **** within 2 weeks don't worry. Then you'll have to use another of the 3 that came with it.
Agreed with everything that OP posted, and agreed with the person above. Mine got scratched within a day but I got over it.
I installed one only because I tried three different Temper glass ones and none sealed correctly. I like it so far installed very good, covers the entire screen. So far so good.
I got a soft screen protector from AliExpress. It's a bit tricky to apply at first but once you get the idea it's not so bad.
The screen protector is really good! It's like silicon , doesn't get scratched easily.
Best part? it's 1.4$ each! What else can you ask for..?
Link:
http://www.aliexpress.com/item/For-LG-G5-Full-Coverage-Soft-Screen-Protector-Guard-Film-for-LG-G5/32618522429.html?spm=2114.13010608.0.54.iHJztH
Here:
Yup good screen protector but it does scuff, so is it perfect no, but one of the better non temper glass protector
I just tried and failed to apply all three. I can't be doing with bubbles or marks on the screen, and who in their right mind decided to put adhesive on a screen protector.
First one too many bubbles, second one, dust, bubbles and scratches, third one, same.
Add to the fact it feels like a ZAGG invisible shield, rubbery rather than glassy.. I will keep it naked from now on.
I have an Xtreme skin skin to install, wish me luck, i'll bloody well need it haha.
Jonathan-H said:
I just tried and failed to apply all three. I can't be doing with bubbles or marks on the screen, and who in their right mind decided to put adhesive on a screen protector.
First one too many bubbles, second one, dust, bubbles and scratches, third one, same.
Add to the fact it feels like a ZAGG invisible shield, rubbery rather than glassy.. I will keep it naked from now on.
I have an Xtreme skin skin to install, wish me luck, i'll bloody well need it haha.
Click to expand...
Click to collapse
I got the dark oak Xtremeskin!
I've put on a tempered glass before, it was kinda bad, lost saturation and brightness, and i got a clear case from spigen, but the case's lips protudes to the center so much that it started to push the screen protectir out!, I eventually removed the tempered glass... Not usre which screen protector to apply on with the spigen case :/
The Spigen Crystal Clear is too thin in my opinion - I killed it within a week. My old Spigen Steinheil Ultra on the S4 was way better. Purchased a CrocFol Premium instead.
Yup I have to change my opinion as well, used it for a bit, scuffed easily, stays clear without the rainbow effect. I had a few defects in my screen protectors, changed them out. Using the otterbox Defender case for now.
1$ tempered glass (rectangular) from AliExpress are perfect of you dont care leaving the top curved part unprotected. No bubbles, no rainbows, no effect on colors\contrast\clarity.
I have a hard time finding a screen protector for my Oneplus 3T.
It has to cover the whole display, has to have glue on the entire surface.
I only found one TPU protector and had a really hard time fitting it without bubbles (I am experienced in mounting glass protectors).
Currently it is mounted properly, but it will come off eventually.
Are screen protectors still necessary on modern phones, especially OP3T with Gorilla Glass?
I have a Tudia Armor case for it, giving it some rubber protection on the sides, but nothing on the lit screen itself.
I always put my phone in my right front pocket. I never have anything else in this pocket except dust.
nadastry said:
I have a hard time finding a screen protector for my Oneplus 3T.
It has to cover the whole display, has to have glue on the entire surface.
I only found one TPU protector and had a really hard time fitting it without bubbles (I am experienced in mounting glass protectors).
Currently it is mounted properly, but it will come off eventually.
Are screen protectors still necessary on modern phones, especially OP3T with Gorilla Glass?
I have a Tudia Armor case for it, giving it some rubber protection on the sides, but nothing on the lit screen itself.
I always put my phone in my right front pocket. I never have anything else in this pocket except dust.
Click to expand...
Click to collapse
yes, they are. I left my iPhone X unprotected for 2 months and the screen picked up multiple scratches.
As far as my opinion I would say no if you are good with few minor scratches and not using it roughly
It depends on how long you want to keep your screen in perfect condition. Without the protective film, you'll see minor scratches in a year's time, even if you're careful
Depends on your usage, case, and device...
Double Sided Full Body PVC case also do the trick.