Related
On my L, accidently flashed xperia U's firmware, then rebooted and died :crying::crying::crying: what can I do? when trying to attach device in fastboot, flashboot mode, nothing happens. Please, please help me guys.
thanks
not solutions ? :crying::crying:
Steve Mc. Gregory said:
not solutions ? :crying::crying:
Click to expand...
Click to collapse
Try flash stock fw back..pull out battery with push power button about 3-5 sec then connect to flash..
If its failed then i guess goodbye to your device..
I'll Try. thanks for support
I too have same problem kindly give me some solution
Your device is dead.
grewal720 said:
I too have same problem kindly give me some solution
Click to expand...
Click to collapse
See possible solution stated above.
aleksander002 said:
Your device is dead.
Click to expand...
Click to collapse
Technically, a non organic thing can't die.
Send from da hood
i have tried but my phone doesn't get into flash mode or fastboot mode.
grewal720 said:
i have tried but my phone doesn't get into flash mode or fastboot mode.
Click to expand...
Click to collapse
Then it's dead, and the only thing you can do about it is send it to a service center.
Isn't there a way for xperia l to recover from hard brick like xperia z1 via test point or something bcz sending for repair will be very expensive and it would be better of buying a new phone.
Is it possible that device becomes totally unrecoverable(hard bricked) when i attempted to change partitions and went wrong.
bassil.alzoubi said:
hi
1-make sure you battery is charged
2-pull out battery for 10 minutes
3-connect your phone in flash mode (hold vol down button then connect usb cable
not work ?
try another usb cable another usb port
i dont think the phone will totally dead by flashing a wrong firmware but i think its a battery issue
Click to expand...
Click to collapse
Thanks for reply. it was port issue. data wasnt working
Guys
I had hard bricked X10. So use JTAG/REFF connection and rebuild your device. It's so hard, but I made it good luck
Hm ..
bassil.alzoubi said:
i told you try another usb port
and dont say thanks ....press it :good:
Click to expand...
Click to collapse
already pressed man thanks for useful reply :good:
Phone was unplugged while flashing a new ROM to the device. I have tried all the methods of bricking buy i am stuck at the first step. My computer does not recognize the phone at all, when i try to boot it into fast boot mode nothing comes up in my device manager.
Any help would be greatly appreciated
noahdenkins said:
Phone was unplugged while flashing a new ROM to the device. I have tried all the methods of bricking buy i am stuck at the first step. My computer does not recognize the phone at all, when i try to boot it into fast boot mode nothing comes up in my device manager.
Any help would be greatly appreciated
Click to expand...
Click to collapse
Go here
http://forum.xda-developers.com/showthread.php?t=3013732
If your issue is unsolved after following this method, post your queries on that thread/topic.
Dude it's evident from ur post that u haven't tried anything like this previously so YouTube a bit then u will understand how to install adb drivers and ****
Sent from my A0001 using Tapatalk
I used the LG Flash tool 2014 to CSE flash a kdz file, everything went alright until it finish loading at the Download mode. The phone turned off, computer can't detect my phone drive anymore. The phone is completely dead, can't charge and basically have no sign at all!!!!! When I now plug into the computer, it appears as OHSUSB_BULK on device manager. Please Please Please! Could any experts could help me out of this? Huge thank you!
hellobyelock118 said:
I used the LG Flash tool 2014 to CSE flash a kdz file, everything went alright until it finish loading at the Download mode. The phone turned off, computer can't detect my phone drive anymore. The phone is completely dead, can't charge and basically have no sign at all!!!!! When I now plug into the computer, it appears as OHSUSB_BULK on device manager. Please Please Please! Could any experts could help me out of this? Huge thank you!
Click to expand...
Click to collapse
Can you try to startup to download mode manually? If possible, then you still be able to flash the kdz again.
Follow this link.
http://www.android.gs/enter-lg-g-pro-2-download-mode/
bkcheah75 said:
Can you try to startup to download mode manually? If possible, then you still be able to flash the kdz again.
Follow this link.
To bkcheah75,
I can't even go to download mode nor the boot up LG logo page, is there any other method could save my phone please?
Click to expand...
Click to collapse
hellobyelock118 said:
bkcheah75 said:
Can you try to startup to download mode manually? If possible, then you still be able to flash the kdz again.
Follow this link.
To bkcheah75,
I can't even go to download mode nor the boot up LG logo page, is there any other method could save my phone please?
Click to expand...
Click to collapse
Press and hold the up volume button, then plug in the USB cable connected from computer.
Click to expand...
Click to collapse
bkcheah75 said:
hellobyelock118 said:
Press and hold the up volume button, then plug in the USB cable connected from computer.
Click to expand...
Click to collapse
Yeah man, I tried but still black screen with no sign at all!
Click to expand...
Click to collapse
When you press or hold the power button, do you see any screen popup with error?
The error you have seen, can you capture the screenshot and share to us?
I did encountered very bad problem on my GPRO2 before (When power up, it just showed few lines). I thought it was bricked, after few tries... I managed to fix it. I just trying to help here.
bkcheah75 said:
When you press or hold the power button, do you see any screen popup with error?
The error you have seen, can you capture the screenshot and share to us?
I did encountered very bad problem on my GPRO2 before (When power up, it just showed few lines). I thought it was bricked, after few tries... I managed to fix it. I just trying to help here.
Click to expand...
Click to collapse
Basically, I could not boot up my phone at all, tried to boot in download mode but still fail to do so. All I can see is when I plug in USB to the computer, it appears as QHSUSB_BULK on device manager. Please Help!
hellobyelock118 said:
Basically, I could not boot up my phone at all, tried to boot in download mode but still fail to do so. All I can see is when I plug in USB to the computer, it appears as QHSUSB_BULK on device manager. Please Help!
Click to expand...
Click to collapse
Hey man, any solution? Just got this problem too. Installed Xposed on my F350K running on 4.4.2. Computer only detected my phone as QHSUSB_BULK with a bunch of storage device. holy cow, just got this phone for 2 days
Tung Thanh Le plzz help me my phone lg g pro 2 f350s is dead Basically, I could not boot up my phone at all, tried to boot in download mode but still fail to do so. All I can see is when I plug in USB to the computer, it appears as QHSUSB_BULK on device manager. Please Help!
malikmaan said:
Tung Thanh Le plzz help me my phone lg g pro 2 f350s is dead Basically, I could not boot up my phone at all, tried to boot in download mode but still fail to do so. All I can see is when I plug in USB to the computer, it appears as QHSUmanager. SB_BULK on device Please Help!
Click to expand...
Click to collapse
hi bro contact me here is my number +233266680604 i can solve that ur phone complete dead problem 100%:good::good:
Solution
ther is a guide how to unbrick g3 same method can be followed for g pro 2 but here we dont need to open the phone as in that duide and chipset selection will be different all other steps are same here is the link https://www.reddit.com/r/LGG3/comments/41wbo3/how_to_unhardbrick_your_lg_g3_jtag/
hi ..
i flashed mokee official in my mi4i .. i used for 3-4 week. after 2 week i flashed crayon tweaks for stop charging n fast charging it was working great . then aftr 2 week i was using uc browser .. suddenly i got pop up google play store has stooped then play service .. then i hit home button .. and i got a pop up that mokkee launcher has stopped .. (15-20 times i got that unfortunatily mokee launcher has stopped) .. then phone automaticaly rebooted.
and it stuck on mokee animation .
i pressed vol up n power off for recovery . i thought if i do wipe data n cache then it will work and boot.. but when i pressed them buttons . it was turned off . and dint on ..
no charging animation
no led
not going in recovery
not going in fastboot
completely dead ..
anyone who can help in this situation???
Try to put it into Recovery Mode or Fastboot mode WHEN connected to A.C. Charging. if nothing appears You should approach Xiaomi Service Center ASAP.
Toruk.Makto said:
Try to put it into Recovery Mode or Fastboot mode WHEN connected to A.C. Charging. if nothing appears You should approach Xiaomi Service Center ASAP.
Click to expand...
Click to collapse
I tried bro .. also connected to pc n tried but nothing heppend no led no charging animation ..
It might got into QDL9008 mode, try installing the proper drivers and see if it gets detected. Might been hard bricked.
Hackerpunk1 said:
It might got into QDL9008 mode, try installing the proper drivers and see if it gets detected. Might been hard bricked.
Click to expand...
Click to collapse
When i connect to pc it sound . Like same when u connect a device ...
But not showing nothing...
And cant go in fastboot so cant install rom
And in command prompt no adb devices is showing ..
I think fully hard bricked ..
Yes i think u r right its in QDL9008 mode.
Cant open mi4i .. i think need to send to service centre ..
I sure there is a way out, try inboxing me and we'll see if something can be done.
Hackerpunk1 said:
I sure there is a way out, try inboxing me and we'll see if something can be done.
Click to expand...
Click to collapse
I dont know how to unboxing mi4i . Can tell me how to open back cover???
UniQ01 said:
I dont know how to unboxing mi4i . Can tell me how to open back cover???
Click to expand...
Click to collapse
Front
https://www.youtube.com/watch?v=Os16XJYi2aE
If the device is already in QDL9008, you don't need to open the device. You just need certain files and flash the emmc for reprogramming.
Hackerpunk1 said:
If the device is already in QDL9008, you don't need to open the device. You just need certain files and flash the emmc for reprogramming.
Click to expand...
Click to collapse
Bro can't install or flash .. bcz its not booting up not going in recovery . No fastboot mode . No charging no led showing
You need to use MiFlash, if with that it doesn't work, try using EMMC Download from QPST
Hackerpunk1 said:
You need to use MiFlash, if with that it doesn't work, try using EMMC Download from QPST
Click to expand...
Click to collapse
Need to put phone in fastboot mode for using miflash ...
Cant go in fastboot mode ... as i said in starting bro ..
Then you should try using EMMC from QPST, PM me, would be much better.
Hackerpunk1 said:
Then you should try using EMMC from QPST, PM me, would be much better.
Click to expand...
Click to collapse
Sorry bro for late reply
My phone was in service center
It was in warranty so now it's okay
But if in future I face same problem then I' ll ask to u for a solution
BTW thanks everyone who replied me
Has the phone been detected as QDL9008?
Need mi toll to flash your devices bro
Hackerpunk1 said:
Has the phone been detected as QDL9008?
Click to expand...
Click to collapse
Hi, My phone is hardbricked. No screen No fastboot No Recovery, But it is detected in device manager as Qualcomm HS- USB Diag. 9006. As you are saying in previous post, I need to flash some file in eMMC software. I downloaded it and installed it.
Can you please guide me further...
Thanks in Advance
I have a problem with my nexus 5, I try to install the recovery and it stays black screen does not enter the bootloader or anything, my pc recognizes it as android adb interface some help.
me to having same problem dont know what to do
pc not recognising my device
Follow this thread: https://forum.xda-developers.com/go...-unbrick-nexus-5-stucked-qualcomm-hs-t3043301
I hope you have an efs backup somewhere if you don't keep trying..
also how did you try to install recovery? there is a multitude of ways and knowing what you did could help a lot.
Jo_Jo_2000 said:
Follow this thread: https://forum.xda-developers.com/go...-unbrick-nexus-5-stucked-qualcomm-hs-t3043301
I hope you have an efs backup somewhere if you don't keep trying..
also how did you try to install recovery? there is a multitude of ways and knowing what you did could help a lot.
Click to expand...
Click to collapse
Hello thanks for your help I will try, I did the procedure with the tool nexus root toolkit I followed the steps my phone stayed so now it vibrates and reboots constantly my pc only recognizes it as mtp usb or android device.
soujirock said:
Hello thanks for your help I will try, I did the procedure with the tool nexus root toolkit I followed the steps my phone stayed so now it vibrates and reboots constantly my pc only recognizes it as mtp usb or android device.
Click to expand...
Click to collapse
Follow the thread and stop using toolkits since they might do obscure things and people cannot help you if you just say "i did it with the toolkit"
Jo_Jo_2000 said:
Follow the thread and stop using toolkits since they might do obscure things and people cannot help you if you just say "i did it with the toolkit"
Click to expand...
Click to collapse
Hello try to perform the steps but in the device manager I do not get any of that I only recognize the phone as android device.
soujirock said:
Hello try to perform the steps but in the device manager I do not get any of that I only recognize the phone as android device.
Click to expand...
Click to collapse
Thanks for your help, download one that said repair nexus 5 dead and now I get this I think I should do something more because now the pc recognizes me so if you could guide me I would thank you very much.
what happens when you try to open the mtp device?
if not try uninstalling all drivers with google..
you should always be able to reach the dload mode even if it's fully working as long as you follow the steps.
Jo_Jo_2000 said:
what happens when you try to open the mtp device?
if not try uninstalling all drivers with google..
you should always be able to reach the dload mode even if it's fully working as long as you follow the steps.
Click to expand...
Click to collapse
Hello what happens if it opens like a usb but on the screen of my cell you can not see anything even I recognize it in fastboot mode but on the screen I see nothing.
How can i get into dload mode
I try to flash it with the method you gave me but I get a message from device was not found in dload mode trying flash programmer.
maybe your screen is just broken?
also citing the thread linked: "If you dont see Qualcomm HS-USB QDLoader 9008 click on the CLICK TO SHOW CONTENT button bellow, otherwise don't and follow the guide."
Jo_Jo_2000 said:
maybe your screen is just broken?
also citing the thread linked: "If you dont see Qualcomm HS-USB QDLoader 9008 click on the CLICK TO SHOW CONTENT button bellow, otherwise don't and follow the guide."
Click to expand...
Click to collapse
Hello my screen is not broken or anything I already recognized the pc driver qualcom 9008 and perform the procedure of the post now my cell recognizes the pc as nexus 5 in usb mode but I do not have the system.
soujirock said:
but I do not have the system.
Click to expand...
Click to collapse
Aka no reaction or no fastboot or a missing partition?
is recovery working?
is bootloader working?
what has appeared on your screen to show you that it isnt broken?
Jo_Jo_2000 said:
Aka no reaction or no fastboot or a missing partition?
is recovery working?
is bootloader working?
what has appeared on your screen to show you that it isnt broken?
Click to expand...
Click to collapse
Hello, it seems that the fastboot mode works because in the pc it recognizes me as android device and I download a program that is called dead nexus 5.bat and this recognizes me and writes the system and performs other operations more but still nothing appears I do not know if the system can be flashed by this method.
i try with this method https://forum.xda-developers.com/google-nexus-5/general/tutorial-how-to-flash-factory-image-t2513701 but nothing
can you execute fastboot commands?
what does that script tell you, where is it from?
Please stop using toolkits, they perform obscure unpredictable things.
Also what makes you so certain your screen isn't broken given that everything works except the screen?
Jo_Jo_2000 said:
can you execute fastboot commands?
what does that script tell you, where is it from?
Please stop using toolkits, they perform obscure unpredictable things.
Also what makes you so certain your screen isn't broken given that everything works except the screen?
Click to expand...
Click to collapse
thanks man i solved my problem