Related
Hello Everyone,
I am a Noob, Yes. Please help. I was trying to install TWRP onto my TF300T. I installed it Via ADB. Had it installed with my stock ROM. I tried to do a backup so I could flash CM10. It said it wasn't mounted. I tried again and then it reboot and now goes straight to TWRP. I can get my device on ADB via the cmd screen but it says that the device is attached in recovery and my serial number is now 01233456789ABCD. Have I completely bricked my tablet? Is there anything I can do? I have been searching the forums for literally hours and am at wits end. Any suggestions would be appreciated. Sorry if this has been gone over time and time again but I can't figure it out. Please help. Thanks
Marc
To add,
When I try to do anything via fastboot it just hangs waiting for device. I can't get it to go to the fastboot page on my tablet, it just goes straight to the TWRP page.
Let me guess... You were on the Asus 4.2.1 OTA release, and installed TWRP 2.4.4.0-JB...
splashg said:
Let me guess... You were on the Asus 4.2.1 OTA release, and installed TWRP 2.4.4.0-JB...
Click to expand...
Click to collapse
Yes, that would be correct. So I managed to reset the device and cold boot back to a working device. Now i'm still wanting to flash a custom recovery and change ROMS to cyanogenmod (had it on my S1 and loved it) but am a bit nervous. How do I reset my partition and clear the old TWRP and flash a working version of CWR via fastboot or a version of TWRP that will work with my OTA rom. I thought I had done quite a bit of research before hand but am feeling a bit overwhelmed now. I don't want to go through another twelve hours of trying every trick I can find on the internet to unbrick my device.
Thanks
Just a few other things to add. So now when i have my device connected to my computer in normal function i can recognize it when I enter adb devices on my cmd prompt. Then I do the fastboot reboot bootloader which it then sends it into the fastboot screen. type in adb devices and it doesn't recognize the device anymore. I try the commands to install the cwm recovery.img and my cmd screen goes through the normal steps saying it's completed it. Then i try to reboot the device through fastboot and it freezes on the bootload screen with the green box no longer flashing on the rck box. Hold power button for six seconds to reboot and i have a working device again. So now i'm lost. How do I reset everything so I can start over, repartition so I can flash a custom recovery and carry on. any help is appreciated.
I don't know how you got yours back, even the bootloader cold-booting linux won't go into the OS for me.
That said, AFAIK, TWRP 2.4.4.0-4.2 or 2.5.0.0-4.2 are the only ones that will work with the 4.2.1 OTA update. Let me know if you somehow manage to get either on there because I can't seem to flash anything.
splashg said:
I don't know how you got yours back, even the bootloader cold-booting linux won't go into the OS for me.
That said, AFAIK, TWRP 2.4.4.0-4.2 or 2.5.0.0-4.2 are the only ones that will work with the 4.2.1 OTA update. Let me know if you somehow manage to get either on there because I can't seem to flash anything.
Click to expand...
Click to collapse
I tried flashing the new correct version of TWRP. it just freezes on the rck tab of the bootloader. It goes through the process on fastboot on my cmd prmt but does nothing on the tablet end. At least I have a working device on 4.2.1 just frustrating that TW didn't state that there is a 4.2 version not just a JB version. So now I can't get OTA updates and can't flash any custom or stock ROM's. So I'm permanently stuck with 4.2 but it's better than being stuck with a brick I guess. This isn't my first time rooting, flashing or working with ADB and fastboot. Did my research before flashing the custom recovery and thought I followed TW's steps very accurately. I hope that they update their site to stop a large number of people soft or hard bricking their devices. I at least can hold out hope that someone will figure out how to re install the bootloader. There has to be a fix as the rest of my device works so the motherboard isn't shot. Good luck. Let me know if anything or anyone figures it out.
lomoski said:
I tried flashing the new correct version of TWRP. it just freezes on the rck tab of the bootloader. It goes through the process on fastboot on my cmd prmt but does nothing on the tablet end. At least I have a working device on 4.2.1 just frustrating that TW didn't state that there is a 4.2 version not just a JB version. So now I can't get OTA updates and can't flash any custom or stock ROM's. So I'm permanently stuck with 4.2 but it's better than being stuck with a brick I guess. This isn't my first time rooting, flashing or working with ADB and fastboot. Did my research before flashing the custom recovery and thought I followed TW's steps very accurately. I hope that they update their site to stop a large number of people soft or hard bricking their devices. I at least can hold out hope that someone will figure out how to re install the bootloader. There has to be a fix as the rest of my device works so the motherboard isn't shot. Good luck. Let me know if anything or anyone figures it out.
Click to expand...
Click to collapse
I finally gave up, sent mine in today, it will cost but what the hell, i want my tablet in working order. I've tried the remedies myself, to no avail.
So off to ASUS.
Let me know what they end up charging you. I did a service request on-line, but haven't heard back yet.
steveb05 said:
Let me know what they end up charging you. I did a service request on-line, but haven't heard back yet.
Click to expand...
Click to collapse
I won't know how much it will cost until the unit is in their hands. I initiated my RMA online as well, they told me i will be contacted by phone after they examine it, I'm prepared to invest another 100 bucks as i got the unit for $299. I'll be hesitant to go much higher. I will post a number when i hear from them, if they haven't replied back to you.
I've got the same problem on my TF300T.
I'm going to try to get it working.
Not entirely sure what caused it, since I had used encryption in cm10.1 prior to flashing Asus stock 4.2.1.
BTW, I've been able to get back to fastboot by running adb reboot bootloader when TWRP is loaded.
Update: Seems to be that new 10.6.x.x bootloader... gotta love Asus :-/
--- Update II----
I can't flash anything in fastboot anymore :-/
People that can't get the roms beyond stock to work, are your phones activated?
Is it possible to use the Pac Man Rom or CM10 on an unactivated phone?
I'm having similar issues to others trying to flash Pac Man and CM10.2. The first boot was fine and I can access everything on the phone fine, including settings. I rebooted and the activation screen (which I skipped as this phone doesn't have service) always pops up but I would like to use it without putting it on a cell network. I can skip the screen fine (until I decide to disable it) but then have issues like the keyboard (physical and touch), systemUI or NAV Bar crashing with a constant message pop up telling me it has crashed. I have returned to stock using RSD and reflashed Pac Man and CM10.2 MANY (15+?) times, doing a clean install 99% of the time but also trying a couple dirty installs to cover my bases. I should also note that I flashed the phone to Cricket but have no plans to activate it anytime soon.
Another thing to note is that I had issues getting the custom roms to boot at all as the initial setup would take hours. One time I though it was a boot loop but I left it on all night and it had booted in the morning. I believe it has something to do with the file check at boot (with my 32GB low speed class SD card) but that seems to be resolved and I can get the custom roms to boot fine (on the first boot) even with my 32GB (witch is fine and has no errors nor is generic, before you ask.) I also have tried 2 4GB cards and a 2GB card, all different brands, with no change in behavior.
I have done everything below multiple times and in different orders.(If needed I can give a direct breakdown step by step but if you could do it with the files below, I have probably tried it)
Wipe the phone (including all storage internal and external SDs included)
Using RDS v6.15
RDS asanti_c_sprint-user-4.1.2-9.8.2Q-122_XT897_FFW-5-6-release-keys-cid9.xml.zip (Works 100% of the time and never has issues. I keep reverting back to this if I actually need to use the phone)
RDS ClockworkMod, TWRP, and Open Recovery without TWRP (Tried different versions when available)
Then used each recovery to install Pac Man or CM10.2 (tried 10.1 once but had the same issues and I didn't see the need to troubleshoot a rom people seemed to not want to develop for. So 10.1 was only tried once but has the same issues)
Installed GApps at this point but I also tried alternate versions of GApps and not installing it at all. All have the same effect and don't seem to be contributing to the problems at all.
A few installed I tried wiping the phone again or installing each zip multiple times. I also verified the zips were good when on the device to make sure there was no corruption at transfer.
I also tried multiple (confirmed working) SD cards and installing from the internal storage.
I have tried installing arrrghhh's Kernel too.
The issue ether seems to be boot loop (if it's doing a file check) or more often it works until I get one of the said crashes after a reboot.(blame Tyler message is getting SO old...) The time I see the errors seems to be accelerated if I mess with the settings a lot but I don't believe it is directly related to the settings.
My next recourse is to try and flash it back to Sprint (maybe check my Cricket settings) and see if that helps, without it being activated.
On a separate note.
If people need help I can help get you back to stock easily. The instructions/guides on here are all but useless if you don't know what you are doing already. I have seen down to "USE RDS" or "DELETE LINE MD5" like people would just know what that means. I understand RDS Lite is a standard tool for flashing phones but it's nigh impossible to find real explanations on what stuff does in context. I understand the basics though, so if anyone has any questions I can walk you through it.
To start with if you are stuck in a loop at the start of a new rom and it loops between the 'Welcome' Screen (Select your Language) and Activation screen just skip the initial setup by tapping the corners on your screen in a clockwise manor when on the 'Welcome' screen to skip the setup there is a video to explain it here
pocketnow(can't post links )com/how-to/android-quick-tip-how-to-bypass-touch-the-android-to-begin-video
Without doing this or activating the phone it seems to loop between those 2 screens forever (might indicate part of the problem with customs roms....)
I hope this is enough info to go off of I can give you a play by play with the actual files if you need. Maybe a video if needed and I'm feeling extra fancy.
Thanks for your time.
Hey buddy,
If you're trying to make a guide, make sure you call it what it is properly - RSD Lite.
Also, maybe clean up your post a bit so it's a proper guide (as you point out, it's needed) and make a separate thread for your question.
To answer your question, the unactivated phone shouldn't be an issue in of itself - you'll just get the nag screen like you were talking about.
I know there is an issue some are having with rebooting the 4.3 ROM's. Have you tried any 4.2.2 versions of anything? Carbon, CM10.1?
I wonder if your "flash" to Cricket is causing issue, I'm not sure. Let me know about 4.2.
Edit - I missed this part on my first read of your PM. Taking hours to boot is NOT normal. Perhaps remove the SD card entirely, flash using the internal SD... I've never heard of that. Anything over say 20 minutes is probably cause for concern.
Thanks for taking time to answer me.
In no way was I trying to make a guide yet but I guess I could. I just hate posting stuff without useful content so I figured throwing that in was better than nothing. I'll clean it up and set up some links later today. It's frustrating to try and make a full guide before I can post links that would be needed for it. You are totally right though! (complain about crappy guides and kind of make one... )
Part of my point there was that I can't post out of Q and A and this wasn't really a question so I made a question out of it and that's how my post ended up.
I have flashed many phones before but like I said I'll try and put it back on Sprint later today (probably will be a few hours) as I backed up the settings the phone came with. I know it was a wall of text and not the easiest to read so you probably missed it but I also said in my first post that I tried the internal SD card many times and the taking hours to boot isn't the standard and doesn't seem to happen at 99% of the time. It seems to be related to the recovery software I use as it happened a lot more when I was testing TWRP and none when I use clockwork.
What Recovery do you recommend? I swear they aren't made equal...
I tested CM10.1 once and it had the exact same issues as CM10.2 and Pac Man so I didn't test it further but if you want me to test it I can. I just didn't want the Rom.
I don't want Carbon either but I'll test that and AOKP next. It's just annoying that the stock rom works perfect but I can't get these to function at all. I almost wish I didn't get Pac Man to work at all. I'm very particular about my settings and NEED these features after I tried them Pac Man is AMAZING.
Thank you for the help and I hope I can get this worked out.
PS I saw that you were frustrated about working on a rom you don't have a device for. I hope you don't let a little thing like that stop you as, for the little time I have used it, it's all I want. Thanks again.
Blasz said:
What Recovery do you recommend? I swear they aren't made equal...
Click to expand...
Click to collapse
Well, OpenRecovery has probably the most work done for this device specifically. I liked TWRP, but it seems lately it has been unstable - you're not the first who has reported issues lately. I don't think CWM has been updated, unfortunately - but perhaps that's a good thing, it's stable that's for sure.
Blasz- I was just about to start a thread when I found yours, and it very accurately describes the issues I've been having. Here's my progress so far.
I got my Photon Q with Sprint and used it for a few months before Sprint started finding creative ways to take my "$79.99" bill and make it more like $140 a month. Naturally, I refused to pay. So I had a Photon Q with no cell service. This is fine, as I only need it to work on WiFi, not 2G/3G and there is no 4G in the area. Anyway.
At the time, I had Ice Cream Sandwich on it, using the (latest?) ICS firmware from Motorola. This worked very well, but I later tried to use a newer firmware, and all the custom ROMs had shown up while I hadn't been looking. All of these seemed to be based on JellyBean. First off, I tried CyanogenMod 10.2. Worked amazing well! I had literally no problems at all. However, while I was experimenting with different software for the phone, and wanted to see if "Arrrgghh"(sp?)'s kernels would give me some decent overclocking capability. Turns out, the kernel I picked wasn't compatible with the JB firmwares (I probably picked an older one by mistake.) Needless to say, it now wouldn't boot. It'd go to the "Unlocked bootloader" screen and stay there all night (literally, I tried that.)
So, I went back into CWM, which is the recovery I have installed. I erased /data, /cache and /system, and also the dalvik cache and battery stats for good measure. I also formatted /pds and /modem, I believe, which was probably dumb of me since I'm not sure what those do. Then I tried re-installing CM 10.2 from CWM. The installation went fine, and it works gorgeously. However, there's two weird issues:
1) WiFi and Bluetooth don't even BEGIN to work! Neither does Cell, as far as I can tell, because where CM used to be unable to make calls or access the internet (of course, I've not been paying my bill), it now shows an empty signal bar or "No Signal" (the little red X) in the notification bar ... When I try to turn on WiFi using the slider in Settings, it moves to "ON" (stays gray) and pauses for a few secs, then goes back to OFF. Same thing for BT. If I open the WiFi menu where you select an AP, it tells me to turn on WiFi. I do, using the slider up top, and the same thing happens. WiFi and BT simply won't turn on. Tried fiddling with every setting I can find.
Before this misadventure with the kernel/reinstall, WiFi worked great. I connected to a local AP and was surfing the net and downloading apps.
2) The system takes a VERY long time to boot up. It sits at the "Unlocked Bootloader" screen for up to a whole minute. Then it goes to the Cyanogen screen for about 30 seconds. Then it gets to the homescreen. It's fine so long as you let it boot up, but this doesn't seem normal.
Next I tried other ROMs thinking that might help. I installed AOKP, PacMan, CM1.0, Carbon, SlimBean, and I think a few others without results-- they all work but WiFi and BlueTooth are dead. PacMan is the only exception-- it boots up and then endlessly gives me "Blame Tyler" errors until I force the machine to shut off.
I also tried an older ROM, since these are all JellyBean ROMs and I wanted to get back to ICS (I'm not that fond of JB's interface) anyway. I was unable to find any ZIPs I could install through CWM of the stock firmware. I found some IMGs that it looks like I could install via Fastboot, but I don't currently have a PC with admin priveleges (it's not mine) so I can't install the drivers to use Fastboot or any part of the SDK. (I can, however, put files on my SD card, that doesn't require privleges.) The closest ROM I found to stock was "TwistedAsanti" beta-1 or whatever it's called. That installs fine, but again, it takes about 2 straight minutes to boot and it's useless after that:
It gets stuck at "Starting Services..." and will sit there forever, even left there all night. Behind this, a dialog pops up saying no cell networks were found and asking if I want to switch to GSM. (i've been trying GSM and CDMA ROMs all this time, I don't need cell access so I doubt it matters which I use. I'm in the USA.) You can pull down the notification bar and get into the Settings, and even launch a couple programs, but I can't find ANY way to get to a homescreen. Task manager shows Circles is running, which is a widget on the homescreen, so where the heck is that screen? .. I try, again, to turn on WiFi or BT without success. The friggin thing just won't turn on.
Did I eff it up by erasing the "PDS" or "modem" partition? Am I missing something obvious or is my phone just possessed?
In a few days I should have access to a computer where I can hopefully use Fastboot and see about installing a stock firmware (wish me luck). Until then, does anyone have a ZIP file I can flash from CWM to get back to an ICS firmware? I managed to find a copy of the stock firmware, in the form of a dump done from TWRP (in .win files). But as far as I know the only way to install TWRP is using Fastboot, and I've explained why I can't do that. I don't know a way to install TWRP from CWM. Maybe I can do it from CM10.2, if I can put APKs or something on my SD card. I can't get it on the network, so I have to copy all the files manually. Needless to say, it's a pain.
After my frenzy of ROM installing, I got frustrated and decided to see if TwistedAsanti would do SOMETHING if I let it sit at "Starting Services" overnight. To my mistake, I left it under my pillow and the system was quite toasty, and the battery had run dead. Plugging it back into the charger, it made a few worrying clicking noises from the speaker, then the green LED came on. This LED seems to mean "I'm charging, but the battery is too dead to turn on for a while." After it sits there a while, the green LED turns off and it just goes black. Or it goes to BOOTLOADER UNLOCKED and bootloops, or goes to black untilyou fiddle with the power button some more. I can once in a blue moon get to CWM. Sometimes it gets to the homescreen. It will charge up to about 4-7% and no further (battery got damaged by the heat?) It doesn't reliably work when plugged in, it likes to shut off at random anyway.
So now I'm stuck with a phone I can't seem to charge, or turn on reliably, and if I *do* get it to boot up, there's no way to connect it to a network.
Needless to say I'm pretty darn frustrated..
Thanks for any advice.
Epicenter714 said:
So now I'm stuck with a phone I can't seem to charge, or turn on reliably, and if I *do* get it to boot up, there's no way to connect it to a network.
Needless to say I'm pretty darn frustrated..
Thanks for any advice.
Click to expand...
Click to collapse
Did you try to use RSD Lite and flash the device back to stock?
arrrghhh said:
Did you try to use RSD Lite and flash the device back to stock?
Click to expand...
Click to collapse
Currently, I have no PC to use that has Admin priveleges, so I can't install the USB drivers or RSDLite. I also can't use fastboot to install TWRP to use the TWRP .win backups I found.
I did get a roommate to let me use his laptop for 10 minutes to try RSD Lite, but I had this result: Loaded the ".xml.zip" file for the 4.0.4 and 4.1.2 firmwares (after removing the 'getvar' line that causes problems) and it says the phone reported "FAIL". No further details. MiniRSD gives no info from the phone other than the model (it all stays blank), is that supposed to happen? I have the phone in "AP Fastboot" mode so I don't see the problem.
The guy who let me use his PC momentarily is computer-illiterate and thinks anything will break it, so he only let me use it momentarily, and won't let me touch it because I accidentally left an icon on his desktop. I'll have to ask someone else, I think I may know somone..
If I do, how do I get around this error in RSD Lite? Will keep doing research on my own .. thanks!
Epicenter714 said:
Currently, I have no PC to use that has Admin priveleges, so I can't install the USB drivers or RSDLite. I also can't use fastboot to install TWRP to use the TWRP .win backups I found.
I did get a roommate to let me use his laptop for 10 minutes to try RSD Lite, but I had this result: Loaded the ".xml.zip" file for the 4.0.4 and 4.1.2 firmwares (after removing the 'getvar' line that causes problems) and it says the phone reported "FAIL". No further details. MiniRSD gives no info from the phone other than the model (it all stays blank), is that supposed to happen? I have the phone in "AP Fastboot" mode so I don't see the problem.
The guy who let me use his PC momentarily is computer-illiterate and thinks anything will break it, so he only let me use it momentarily, and won't let me touch it because I accidentally left an icon on his desktop. I'll have to ask someone else, I think I may know somone..
If I do, how do I get around this error in RSD Lite? Will keep doing research on my own .. thanks!
Click to expand...
Click to collapse
Well remember - if you are on JB and you are downgrading to ICS, there are additional lines to remove.
Other than that, not sure why it would fail. Make sure 'fastboot devices' works in the command line before doing RSD perhaps.
arrrghhh said:
Well remember - if you are on JB and you are downgrading to ICS, there are additional lines to remove.
Other than that, not sure why it would fail. Make sure 'fastboot devices' works in the command line before doing RSD perhaps.
Click to expand...
Click to collapse
I'm trying to wipe the device clean and install ICS. Are there any other lines I need to remove? ..
As for Fastboot.. I did 'Fastboot Devices' and got no devices listed. How come it shows up in MiniRSD? .. I have the drivers installed, Windows says it installed an ADB device successfully. What are some reasons that might not work? Is there any sort of guide for this? Thank you
---------- Post added at 05:51 PM ---------- Previous post was at 05:29 PM ----------
Oh, as far as the weird booting problem, it seems the battery is fine and the charger died coincidentally at the same time as the overheating did. So my only problem is software now.. thanks.
Epicenter714 said:
I'm trying to wipe the device clean and install ICS. Are there any other lines I need to remove? ..
As for Fastboot.. I did 'Fastboot Devices' and got no devices listed. How come it shows up in MiniRSD? .. I have the drivers installed, Windows says it installed an ADB device successfully. What are some reasons that might not work? Is there any sort of guide for this? Thank you
---------- Post added at 05:51 PM ---------- Previous post was at 05:29 PM ----------
Oh, as far as the weird booting problem, it seems the battery is fine and the charger died coincidentally at the same time as the overheating did. So my only problem is software now.. thanks.
Click to expand...
Click to collapse
I have no clue what MiniRSD is - you mean RSD Lite?
If it doesn't show up in fastboot devices, sort that out before trying to use RSD.
As I stated previously, if you were on JB and going down to ICS you have additional lines which are needed to remove.
Yes, RSD Lite. I don't know where I got MiniRSD from.
I got it to show up in fastboot devices, but adb devices doesn't show it. Weird. Is that OK?
I was able to flash TWRP to the phone with Fastboot. RSD Lite was unable to find the phone. However, I opened the XML file and was able to figure out the flash commands to enter from a command prompt, so I did that:
I got these results... all of the files flashed successfully to stock, except for two. I forget the first, haven't got it in front of me, but here's the big one: SYSTEM! (Important, no?) Here's the error from fastboot:
>> fastboot flash system system.img.ext4
fastboot said:
target reports max download size 31457280 bytes
Invalid sparse file format at header magi
Click to expand...
Click to collapse
(then, Fastboot crashes.)
Does anyone know how to fix that? Also, the system image is way bigger than 31.4 MB. What is it talking about?
Thanks!
Epicenter714 said:
Yes, RSD Lite. I don't know where I got MiniRSD from.
I got it to show up in fastboot devices, but adb devices doesn't show it. Weird. Is that OK?
I was able to flash TWRP to the phone with Fastboot. RSD Lite was unable to find the phone. However, I opened the XML file and was able to figure out the flash commands to enter from a command prompt, so I did that:
I got these results... all of the files flashed successfully to stock, except for two. I forget the first, haven't got it in front of me, but here's the big one: SYSTEM! (Important, no?) Here's the error from fastboot:
>> fastboot flash system system.img.ext4
(then, Fastboot crashes.)
Does anyone know how to fix that? Also, the system image is way bigger than 31.4 MB. What is it talking about?
Thanks!
Click to expand...
Click to collapse
I would NOT recommend entering those fastboot commands in the XML file manually unless you KNOW what you are doing.
Sort out why RSD isn't working. adb and fastboot are two different things. If fastboot devices shows the device, RSD Lite should work fine. Try again.
Hey folks...I'm running into a problem I was hoping someone might be able to help with.
Earlier today I pulled my phone out of my pocket at work and saw that it was off...I thought that the battery must have died sooner than I thought. I started charging it in the car on the way home and it wouldn't boot up like normal. It would get to the google or "dots" screen and then reboot. I again thought that the battery might just be really low. After getting home and charging the phone all the way I still can't get it to boot up. As of now, one of 3 things will happen...
1-The phone will turn on, get to the google screen and bootloop (usually when plugged in).
2-The phone will turn on, get to the google screen and freeze.
3-Get to the "dots" screen and either swirl forever or eventually reboot and do one of the above again.
I've read some threads where people suggest this is a faulty power button, that doesn't seem to be the case for me though because I can get into fastboot and it won't select anything or turn off without me doing it.
I've used WugFresh NRT and wiped/reflashed android. I'm running out of ideas. Do you have any others?
I was running the stock 5.0.1, unlocked, not currently rooted.
Thanks!
kyle313 said:
Hey folks...I'm running into a problem I was hoping someone might be able to help with.
Earlier today I pulled my phone out of my pocket at work and saw that it was off...I thought that the battery must have died sooner than I thought. I started charging it in the car on the way home and it wouldn't boot up like normal. It would get to the google or "dots" screen and then reboot. I again thought that the battery might just be really low. After getting home and charging the phone all the way I still can't get it to boot up. As of now, one of 3 things will happen...
1-The phone will turn on, get to the google screen and bootloop (usually when plugged in).
2-The phone will turn on, get to the google screen and freeze.
3-Get to the "dots" screen and either swirl forever or eventually reboot and do one of the above again.
I've read some threads where people suggest this is a faulty power button, that doesn't seem to be the case for me though because I can get into fastboot and it won't select anything or turn off without me doing it.
I've used WugFresh NRT and wiped/reflashed android. I'm running out of ideas. Do you have any others?
I was running the stock 5.0.1, unlocked, not currently rooted.
Thanks!
Click to expand...
Click to collapse
Did you try flashing factory images?
ryukiri said:
Did you try flashing factory images?
Click to expand...
Click to collapse
Yeah, that was what I flashed :/
If you can get into fastboot you "should" be able to flash stock images... Obviously this will revert any root and you will need to flash TWRP/CWM recovery after.
I assume you have a Windows PC with fastboot/adb setup and all drivers etc..
- Download latest "stock" hammerhead images (I cannot post links due to XDA rules... so: "developers.google.com/android/nexus/images#hammerhead"
- Extract the .tgz archive contents on your PC into a folder
- Boot the N5 into fastboot and plug USB cable from phone into your PC
- Go to the folder with the extracted files and run the "flash-all.bat" script on Windows
**Hopefully at this point your device will start to respond.. I.e, on fastboot screen, at the bottom you will see "writing" or something, as the script runs on the command window on your PC.**
If this works, you should be able to reboot once complete and then wait to see if you can get back into your phone.. then you can fastboot again and flash custom recovery, and then whatever rom.
If however you have a hardware issue (i.e, even after the above process it fails) then I am not sure what you could do... I guess ensure it has a complete charge. If you can get into fastboot and the buttons are responsive then it should not be a faulty power button.
Hope this helps :good:
Have you tried a simple factory reset? Reason I ask is it was working fine so sounds like something needs "flushing out" clear cache etc.
kyle313 said:
Hey folks...I'm running into a problem I was hoping someone might be able to help with.
Earlier today I pulled my phone out of my pocket at work and saw that it was off...I thought that the battery must have died sooner than I thought. I started charging it in the car on the way home and it wouldn't boot up like normal. It would get to the google or "dots" screen and then reboot. I again thought that the battery might just be really low. After getting home and charging the phone all the way I still can't get it to boot up. As of now, one of 3 things will happen...
1-The phone will turn on, get to the google screen and bootloop (usually when plugged in).
2-The phone will turn on, get to the google screen and freeze.
3-Get to the "dots" screen and either swirl forever or eventually reboot and do one of the above again.
I've read some threads where people suggest this is a faulty power button, that doesn't seem to be the case for me though because I can get into fastboot and it won't select anything or turn off without me doing it.
I've used WugFresh NRT and wiped/reflashed android. I'm running out of ideas. Do you have any others?
I was running the stock 5.0.1, unlocked, not currently rooted.
Thanks!
Click to expand...
Click to collapse
Did you choose the right model and firmware before you flash in WugFresh NRT?
The above could be right, however when I've used it, it's pointed out if I made that mistake. Having used his software dozens of times I've found it will bring any Nexus 5 back to life.
howard bamber said:
The above could be right, however when I've used it, it's pointed out if I made that mistake. Having used his software dozens of times I've found it will bring any Nexus 5 back to life.
Click to expand...
Click to collapse
Hello! I am apologize for that I didn't read the OP carefully. This happened to me once in that particulary way, but it was immediately after flashing. OP says that it happened suddenly, without reason. So now I am the one, who doesn't read, right? Sorry for that.
Regards, Zagor
Thanks for the responses, but I'm still having trouble.
I have been able to successfully write the newest stock android 3 times (1 without full wipe, 2 with) and the phone still can't boot up and goes through one of the three issues above.
I've also been able to get to the system recovery from the bootloader and I've tried wiping the cache and doing a factory reset from there and the problem remains.
I'd contact google, but I bought it at launch so I don't think they'll do anything for me since it's been 1+ years.
kyle313 said:
Thanks for the responses, but I'm still having trouble.
I have been able to successfully write the newest stock android 3 times (1 without full wipe, 2 with) and the phone still can't boot up and goes through one of the three issues above.
I've also been able to get to the system recovery from the bootloader and I've tried wiping the cache and doing a factory reset from there and the problem remains.
I'd contact google, but I bought it at launch so I don't think they'll do anything for me since it's been 1+ years.
Click to expand...
Click to collapse
Sounds like you have a bad nand sector. From fastboot try:
Code:
fastboot oem lock
Then reboot into fastboot and check if it's locked or not. If the device isn't locked your emmc is corrupt and there is nothing you can do. If that is the case call Google and they will most likely help you out with a RMA.
theesotericone said:
Sounds like you have a bad nand sector. From fastboot try:
Code:
fastboot oem lock
Then reboot into fastboot and check if it's locked or not. If the device isn't locked your emmc is corrupt and there is nothing you can do. If that is the case call Google and they will most likely help you out with a RMA.
Click to expand...
Click to collapse
I was actually able to relock the phone.
Luckily I called google and they're going to send me a replacement.
If anyone else has any other ideas, I'll still take them...I'd rather not be without a phone for the next week!
You won't be without a phone - they are sending a refurbish unit to you , putting a block on your credit card and waiting for you phone to arive at them. Once that happens they will release the funds.
Hello guys,
so two days ago just when I was heading into work my phone randomly started restarting itself again and again. I had it in my pocket, mobile data and wifi off and nothing really going on when this happened. I was on stock Cyanogen OS with 6.0.1, rooted and with Xposed, but nothing too crazy or experimental.
The phone would boot with a small vibration to the Oneplus logo with the "Powered by Android" writing, stay on that for about 17-18 seconds, then reboot again. No way of going to the recovery with the hardware keys, it would just reboot the same again and again. Since I couldn't really do much, not turn it off and no way of disconnecting the battery, I just had to watch it reboot helplessly until the battery was dead. At home with some hassle I could get it charged again, which basically consisted of charging it while it kept rebooting and cooling it while doing that since it would get really, really hot.
The only option that really works is is getting it into fastboot via the volume up + power button. But in fastboot nothing I did so far changed even the smalles thing about it's behaviour. I tried flashing a new recovery image, letting it boot into the recovery via fastboot (both stock recovery and TWRP), reflashing the complete OS via fastboot again (CM 13 ZNH2KAS3P0), completely wiping it via fastboot and flashing an older ROM (CM11S XNPH44S) but so far nothing has even changed a thing. It keeps booting to the Oneplus logo for about 17-18 seconds before rebooting. The only thing that has changed is with the CM11S ROM the fastboot logo of the android head is now bigger.
I checked the bootloader via fastboot, but it's still unlocked.
So yeah, I'm at my wits end and desperate for any help. At this point I fear it might be a hardware issue and I can trash it, but I'm ready to grasp for straws as I don't really have the money for a new device yet.
Any help is appreciated! Thanks guys!
Atomschlumpf said:
Hello guys,
so two days ago just when I was heading into work my phone randomly started restarting itself again and again. I had it in my pocket, mobile data and wifi off and nothing really going on when this happened. I was on stock Cyanogen OS with 6.0.1, rooted and with Xposed, but nothing too crazy or experimental.
The phone would boot with a small vibration to the Oneplus logo with the "Powered by Android" writing, stay on that for about 17-18 seconds, then reboot again. No way of going to the recovery with the hardware keys, it would just reboot the same again and again. Since I couldn't really do much, not turn it off and no way of disconnecting the battery, I just had to watch it reboot helplessly until the battery was dead. At home with some hassle I could get it charged again, which basically consisted of charging it while it kept rebooting and cooling it while doing that since it would get really, really hot.
The only option that really works is is getting it into fastboot via the volume up + power button. But in fastboot nothing I did so far changed even the smalles thing about it's behaviour. I tried flashing a new recovery image, letting it boot into the recovery via fastboot (both stock recovery and TWRP), reflashing the complete OS via fastboot again (CM 13 ZNH2KAS3P0), completely wiping it via fastboot and flashing an older ROM (CM11S XNPH44S) but so far nothing has even changed a thing. It keeps booting to the Oneplus logo for about 17-18 seconds before rebooting. The only thing that has changed is with the CM11S ROM the fastboot logo of the android head is now bigger.
I checked the bootloader via fastboot, but it's still unlocked.
So yeah, I'm at my wits end and desperate for any help. At this point I fear it might be a hardware issue and I can trash it, but I'm ready to grasp for straws as I don't really have the money for a new device yet.
Any help is appreciated! Thanks guys!
Click to expand...
Click to collapse
how old is the device?
As far as I know my sister bought it around summer 2014 when it was released, I got it in late 2015
Atomschlumpf said:
As far as I know my sister bought it around summer 2014 when it was released, I got it in late 2015
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
AFAIK,If this toolkit can't fix your device then it's definitely hw issue.
Mr.Ak said:
https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
AFAIK,If this toolkit can't fix your device then it's definitely hw issue.
Click to expand...
Click to collapse
Well, the tool won't even recognize my phone, so I guess I'm **** out of luck ¯\_(ツ)_/¯
****ing great....
Atomschlumpf said:
Well, the tool won't even recognize my phone, so I guess I'm **** out of luck ¯\_(ツ)_/¯
****ing great....
Click to expand...
Click to collapse
Lol,gave up that early?
It needs around 10 tries to get it correctly recognised.
Use XP system with the proper drivers given in the above thread.This tool doesn't work on adb/fastboot,it works on Usb Debugging Port,hence requires different drivers.
Mr.Ak said:
Lol,gave up that early?
It needs around 10 tries to get it correctly recognised.
Use XP system with the proper drivers given in the above thread.This tool doesn't work on adb/fastboot,it works on Usb Debugging Port,hence requires different drivers.
Click to expand...
Click to collapse
No, I didn't. I tried the USB Drivers I had already installed, the drivers that came in the package and the QPST Tool suggested in the thread on both my and my girlfriends laptop. But if it doesn't work on ADB/fastboot I probably can't use it anyway since my only two options are having the phone on the fastboot screen or having it constantly reboot....
At this point I'm just really, really frustrated and have sorta accepted it's very likely a hardware issue
I'm with the same problem. In my case, the tool does recognize and shows green after the end but when i try to boot, it only shows the boot logo.
I can enter in fastboot and trying the command "fastboot continue" the brightness goes up, but nothing else
already tried various tools, back to stock, qualcomm , and none worked, so can i throw it out of the window?
Edit: can't enter in recovery, and unlike the op, my phone doesn't reboot (at least i didn't notice it)
So I got this Oneplus one from my friend and it's come to me to revive it as there is something wrong with it.. The current state of the phone is that when it's plugged on the computer it can go into fastboot mode or when I try to boot it I will see the oneplus one logo and then it will bootloop. No recovery mode. For some reason without plugging in the phone when I try to start it the phone just vibrates and then goes off and the screen is black all the time. Have charged the phone for an hour to make sure it's not out of juice.
This phone has unlocked bootloader and was on Lineage OS if I am not wrong but I am sure this friend has done something wrong in flashing the wrong file. I know there are loads of solutions which I have tried. Trust me I've tried all and then I am making this new thread or else I won't replicate content.
Things that I tried :
1. Tried flashing cm-13.1.2-ZNH2KAS3P0-bacon-signed-fastboot_64GB via fastboot mode. Everything writes properly but still the same bootlooping and no recovery.
2. Tried flashing Color OS via MSM8974DownloadTool. Everything again goes fine and it's green but again got the Red oneplus one logo this time (maybe that's the color OS boot image) and then bootlooping. Also no fastboot in this mode.
3. Tried Oneplus One Patch released by them officially on their forum to revert the phone to complete stock. Again same issue.
Is there anything else I need to try to make this phone work or is this going to the bin
Any leads would be appreciated from you guys.
Thanks.
have you tried swapping out the micro usb cable because that might be your problem
Replace the batteries with a new one....
Try using fastboot image of cm11s, the very first factory rom for bacon.
I once had to go this far back when flashing sail rom or something
OK let me try with a new cable and let me try flashing cm11. Will update. Thanks.
Update : Trying since morning to get the CM11 fastboot file but unable to get it. It's there on android host server but I am getting constant speed of 10KB/s. Kept it to download for 6 hours and it failed to download.
Anyone has a google drive link to the file? It would be a great help.
If fastboot works there shouldn't be problems at all. First of all wipe everything including internal(search commands online)...also try "fastboot oem unlock" command again. Then just simply flash the latest TWRP via fastboot and from TWRP flash Official LOS15.1(works beautifully) and gapps.
i had somthing simular happened and what i did was i flashed color os then flashed twrp then cm and then booted it (it worked) then flash linage os 15.1 and thats that (i did this cuz i bricked mine while trying to make a boot logo)and btw make sure you have not got the color os boot logo set as the boot logo while installing other roms due to the fact color os boot logo stops or roms from loading make sure you have got the original boot logo!
choosymoron said:
OK let me try with a new cable and let me try flashing cm11. Will update. Thanks.
Update : Trying since morning to get the CM11 fastboot file but unable to get it. It's there on android host server but I am getting constant speed of 10KB/s. Kept it to download for 6 hours and it failed to download.
Anyone has a google drive link to the file? It would be a great help.
Click to expand...
Click to collapse
who are you downloading it from aka which developer
I am inside the OS so the issue was to do with the cable. So stupid but I guess flashing Color OS did help. Thanks a lot guys. We can close this thread. Also the battery seems to be broken, will have to change that.
because i had the same issue a few months back i totally bricked my opo and i thought my phone was gone and not coming back